The Orange Pi PC 2 is a typical single board computer using the
Allwinner H5 SoC. Apart from the usual suspects it features three
separately driven USB ports and a Gigabit Ethernet port.
Also it has a SPI NOR flash soldered, from which the board can boot
from. This enables the SBC to behave like a "real computer" with
built-in firmware.
Add the board specific .dts file, which includes the H5 .dtsi and
enables the peripherals that we support so far.
Reviewed-by: Rask Ingemann Lambertsen <rask@formelder.dk>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
[Icenowy: dropped all GPIO pinctrl nodes, change red LED gpio,
change MMC cd to active-low, rename some node names to prevent
underscores]
Signed-off-by: Icenowy Zheng <icenowy@aosc.xyz>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The Allwinner H5 SoC is pin-compatible to the H3 SoC, but uses
Cortex-A53 cores instead.
Based on the now shared base .dtsi describing the common peripherals
describe the H5 specific nodes on top of that.
That symlinks in the sunxi-h3-h5.dtsi from the arch/arm tree.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
[Icenowy: add H5 pinctrl compatible, and changes for my h3-h5 dtsi
refactor, commit message changed to meet new arm64 naming scheme,
drop H3 pinctrl compatible because of interrupt bank change, drop
H3 ccu compatible because of clock change, drop ccu node as it come
into h3-h5 dtsi]
Signed-off-by: Icenowy Zheng <icenowy@aosc.xyz>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Allwinner H3/H5 have a dual-routed USB PHY0 -- routed to either OHCI/EHCI
or MUSB controller.
Add device nodes for these controllers.
Signed-off-by: Icenowy Zheng <icenowy@aosc.xyz>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The new Allwinner H5 SoC is pin-compatible to the H3 SoC, but with the
Cortex-A7 cores replaced by Cortex-A53 cores and the MMC controller
updated. So we should really share almost the whole .dtsi.
In preparation for that move the peripheral parts of the existing
sun8i-h3.dtsi into a new sunxi-h3-h5.dtsi.
The actual sun8i-h3.dtsi then includes that and defines the H3 specific
parts on top of it.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
[Icenowy: also split out mmc and gic, as well as pio and ccu's
compatible, and make drop of skeleton into a seperated patch]
Signed-off-by: Icenowy Zheng <icenowy@aosc.xyz>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
According to the datasheets provided by Allwinner, both Allwinner H3 and
H5 use GIC-400 as their interrupt controller.
For better device tree reusing, correct the GIC compatible in H3 DTSI to
"arm,gic-400", thus this node can be reused in H5.
Signed-off-by: Icenowy Zheng <icenowy@aosc.xyz>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
After converting to generic pinconf binding, pinctrl-a10.h is now not
used at all.
Drop its inclusion for H3 DTSI.
Signed-off-by: Icenowy Zheng <icenowy@aosc.xyz>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The skeleton.dtsi file is now deprecated, and do not exist in ARM64
environment.
Since we will soon reuse most part of H3 DTSI for H5, which is an ARM64
chip, drop skeleton.dtsi inclusion now.
Signed-off-by: Icenowy Zheng <icenowy@aosc.xyz>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
This commit makes use of the axp209.dtsi file to define the
AXP209 PMIC. While here, define the rails that are enabled on
this board.
Tested checking the regulator voltage varies according to the
CPU frequency.
Signed-off-by: Ezequiel Garcia <ezequiel@vanguardiasur.com.ar>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The SinA31s has a coaxial SPDIF output. Enable it.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
This adds the cpu-supply DT property to the cpu0 DT node needed by
the board to adapt the regulator voltage depending on the currently used
OPP.
Signed-off-by: Quentin Schulz <quentin.schulz@free-electrons.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
This adds almost all operating points allowed for the A33 as defined by
fex files available at:
https://github.com/linux-sunxi/sunxi-boards/tree/master/sys_config/a33
There are more possible frequencies in this patch than there are in the
fex files because the fex files only give an interval of possible
frequencies for a given voltage. All supported frequencies are defined
in the original driver code in Allwinner vendor tree.
There are two missing frequencies though: 1104MHz and 1200MHz which
require the CPU to have 1.32V supplied, which is higher than the default
voltage.
Without all A33 boards defining the CPU regulator, we cannot have these
two frequencies as it would cause the CPU to try to run a higher
frequency without "overvolting" which is very likely to crash the CPU.
Therefore, these two frequencies must be enabled on a per-board basis.
Signed-off-by: Quentin Schulz <quentin.schulz@free-electrons.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The NextThing Co. CHIP has an AXP209 PMIC and can be power-supplied by
ACIN via the CHG-IN pin.
This enables the ACIN power supply subnode in the DT.
Signed-off-by: Quentin Schulz <quentin.schulz@free-electrons.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The Sinlinx SinA33 has an AXP223 PMIC and an ACIN connector, thus, we
enable the ACIN power supply in its Device Tree.
Signed-off-by: Quentin Schulz <quentin.schulz@free-electrons.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The X-Powers AXP22X PMIC exposes the status of AC power supply.
This adds the AC power supply subnode for the AXP22X PMIC.
Signed-off-by: Quentin Schulz <quentin.schulz@free-electrons.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The X-Powers AXP20X PMIC exposes the status of AC power supply, the
current current and voltage supplied to the board by the AC power
supply.
This adds the AC power supply subnode for AXP20X PMIC.
Signed-off-by: Quentin Schulz <quentin.schulz@free-electrons.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
All dts files for the sunxi platform have been switched to the generic
pinconf bindings. As a result, the sunxi specific pinctrl macros are
no longer used.
Remove the #include entry with the following command:
sed --follow-symlinks -i -e '/pinctrl\/sun4i-a10.h/D' \
arch/arm/boot/dts/sun?i*.*
arch/arm/boot/dts/sun9i-a80.dtsi was then edited to remove the extra
empty line.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The old sunxi specific pinctrl bindings are deprecated, in favor of
the new generic pinconf bindings. Also, we are moving towards handling
GPIO pinmux settings that don't require extra bias or drive strength
settings to use the GPIO bindings only.
This patch removes the last instance of the sunxi specific pinctrl
bindings that use the pinctrl header by dropping the pinmux setting
for the audio codec's PA (external amplifier) control GPIO. The pin
is pulled down externally.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The variable 'data' is assigned null and never re-assigned. There
is also a redundant check for data being non-null which is always
false, so remove this and the variable data and dma_addr as they
are not used once the dead code has been removed.
Detected with CoverityScan, CID#1324015 ("'Constant' variable gaurds
dead code")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Jie Yang <yang.jie@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Intel SST driver spews an info message "FW Versoin xxxx" at each time
the device gets initialized. Since it's triggered at each PM (or even
runtime PM), it appears so ofetn, and rather becomes annoying than
useful.
This patch suppresses the superfluous messages by checking the
currently loaded FW version with the previously loaded one.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
commit 1351aaeb50 ("spi: spi-ti-qspi: Use dma_engine wrapper for dma
memcpy call") introduced this warning:
drivers/spi/spi-ti-qspi.c: In function 'ti_qspi_dma_xfer':
drivers/spi/spi-ti-qspi.c:398:21: warning: unused variable 'dma_dev' [-Wunused-variable]
struct dma_device *dma_dev = chan->device;
Fix it by removing the unused variable.
Signed-off-by: Vignesh R <vigneshr@ti.com>
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Mark Brown <broonie@kernel.org>
Commit e8a9c58fcd ("drm/i915: Unify active context tracking between
legacy/execlists/guc") converted the legacy intel_ringbuffer submission
to the same context pinning mechanism as execlists - that is to pin the
context until the subsequent request is retired. Previously it used the
vma retirement of the context object to keep itself pinned until the
next request (after i915_vma_move_to_active()). In the conversion, I
missed that the vma retirement was also responsible for marking the
object as dirty. Mark the context object as dirty when pinning
(equivalent to execlists) which ensures that if the context is swapped
out due to mempressure or suspend/hibernation, when it is loaded back in
it does so with the previous state (and not all zero).
Fixes: e8a9c58fcd ("drm/i915: Unify active context tracking between legacy/execlists/guc")
Reported-by: Dennis Gilmore <dennis@ausil.us>
Reported-by: Mathieu Marquer <mathieu.marquer@gmail.com>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=99993
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=100181
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: <drm-intel-fixes@lists.freedesktop.org> # v4.11-rc1
Link: http://patchwork.freedesktop.org/patch/msgid/20170322205930.12762-1-chris@chris-wilson.co.uk
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
(cherry picked from commit 5d4bac5503)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
When it is determined that the clock is actually unstable, and
we switch from stable to unstable, the __clear_sched_clock_stable()
function is eventually called.
In this function we set gtod_offset so the following holds true:
sched_clock() + raw_offset == ktime_get_ns() + gtod_offset
But instead of getting the latest timestamps, we use the last values
from scd, so instead of sched_clock() we use scd->tick_raw, and
instead of ktime_get_ns() we use scd->tick_gtod.
However, later, when we use gtod_offset sched_clock_local() we do not
add it to scd->tick_gtod to calculate the correct clock value when we
determine the boundaries for min/max clocks.
This can result in tick granularity sched_clock() values, so fix it.
Signed-off-by: Pavel Tatashin <pasha.tatashin@oracle.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: hpa@zytor.com
Fixes: 5680d8094f ("sched/clock: Provide better clock continuity")
Link: http://lkml.kernel.org/r/1490214265-899964-2-git-send-email-pasha.tatashin@oracle.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
If the child domain prefers tasks to go siblings, the local group could
end up pulling tasks to itself even if the local group is almost equally
loaded as the source group.
Lets assume a 4 core,smt==2 machine running 5 thread ebizzy workload.
Everytime, local group has capacity and source group has atleast 2 threads,
local group tries to pull the task. This causes the threads to constantly
move between different cores. This is even more profound if the cores have
more threads, like in Power 8, smt 8 mode.
Fix this by only allowing local group to pull a task, if the source group
has more number of tasks than the local group.
Here are the relevant perf stat numbers of a 22 core,smt 8 Power 8 machine.
Without patch:
Performance counter stats for 'ebizzy -t 22 -S 100' (5 runs):
1,440 context-switches # 0.001 K/sec ( +- 1.26% )
366 cpu-migrations # 0.000 K/sec ( +- 5.58% )
3,933 page-faults # 0.002 K/sec ( +- 11.08% )
Performance counter stats for 'ebizzy -t 48 -S 100' (5 runs):
6,287 context-switches # 0.001 K/sec ( +- 3.65% )
3,776 cpu-migrations # 0.001 K/sec ( +- 4.84% )
5,702 page-faults # 0.001 K/sec ( +- 9.36% )
Performance counter stats for 'ebizzy -t 96 -S 100' (5 runs):
8,776 context-switches # 0.001 K/sec ( +- 0.73% )
2,790 cpu-migrations # 0.000 K/sec ( +- 0.98% )
10,540 page-faults # 0.001 K/sec ( +- 3.12% )
With patch:
Performance counter stats for 'ebizzy -t 22 -S 100' (5 runs):
1,133 context-switches # 0.001 K/sec ( +- 4.72% )
123 cpu-migrations # 0.000 K/sec ( +- 3.42% )
3,858 page-faults # 0.002 K/sec ( +- 8.52% )
Performance counter stats for 'ebizzy -t 48 -S 100' (5 runs):
2,169 context-switches # 0.000 K/sec ( +- 6.19% )
189 cpu-migrations # 0.000 K/sec ( +- 12.75% )
5,917 page-faults # 0.001 K/sec ( +- 8.09% )
Performance counter stats for 'ebizzy -t 96 -S 100' (5 runs):
5,333 context-switches # 0.001 K/sec ( +- 5.91% )
506 cpu-migrations # 0.000 K/sec ( +- 3.35% )
10,792 page-faults # 0.001 K/sec ( +- 7.75% )
Which show that in these workloads CPU migrations get reduced significantly.
Signed-off-by: Srikar Dronamraju <srikar@linux.vnet.ibm.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Vincent Guittot <vincent.guittot@linaro.org>
Link: http://lkml.kernel.org/r/1490205470-10249-1-git-send-email-srikar@linux.vnet.ibm.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
By using "UD0" for WARN()s we remove the function call and its possible
__FILE__ and __LINE__ immediate arguments from the instruction stream.
Total image size will not change much, what we win in the instruction
stream we'll lose because of the __bug_table entries. Still, saves on
I$ footprint and the total image size does go down a bit.
text data filename
10702123 4530992 defconfig-build/vmlinux.orig
10682460 4530992 defconfig-build/vmlinux.patched
(UML didn't seem to use GENERIC_BUG at all, so remove it)
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Reviewed-by: Josh Poimboeuf <jpoimboe@redhat.com>
Cc: Arjan van de Ven <arjan@linux.intel.com>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Richard Weinberger <richard.weinberger@gmail.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Commit 8e3ba95f41 ("dmaengine: cppi41: use managed functions devm_*()")
moved the code to devm_* but erranously changed a varible name, so fix it.
drivers/dma/cppi41.c:1052:5: error: 'struct cppi41_dd' has no member named 'qmrg_mem'
cdd->qmrg_mem = devm_ioremap_resource(dev, mem);
^
drivers/dma/cppi41.c:1053:16: error: 'struct cppi41_dd' has no member named 'qmrg_mem'
if (IS_ERR(cdd->qmrg_mem))
^
drivers/dma/cppi41.c:1054:21: error: 'struct cppi41_dd' has no member named 'qmrg_mem'
return PTR_ERR(cdd->qmrg_mem);
^
Fixes: 8e3ba95f41 ("dmaengine: cppi41: use managed functions devm_*()")
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Functions udc_enable() and udc_disable() have a duplicated prototype.
Remove it.
Acked-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Petr Cvek <petr.cvek@tul.cz>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
dwc3_log_msg trace class isn't used any more. Suggest to remove it.
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Rearrange statements in mv_ep_enable function so that it’s obvious
what the switch does and how zlt, ios and mult variables are
initialised. Most notably, this gets rid of an implicit fall-through
so people don’t have to wonder whether it was intenional or not.
Addresses-Coverity-ID: 201385
Reported-by: Gustavo A. R. Silva <garsilva@embeddedor.com>
Signed-off-by: Michal Nazarewicz <mina86@mina86.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
This bit is only supposed to be used with known
buggy PHYs, however some platforms might erroneously
set it. In order to avoid it, let's make sure this
bit is always cleared. If some PHY needs this, we
will need to add a quirk flag.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
The trouble here is that it does multiple atomic commits under one
drm_modeset_lock_all, which breaks the behind-the-scenes acquire
context magic that function pulls off. It's much better to have one
overall atomic commit. That we still have multiple atomic commits
prevents us from adding some pretty useful debug checks to the atomic
machinery.
Hence it is really a bad idea to call the legacy
drm_crtc_force_disable_all() function. There's 2 atomic drivers using
this still, nouveau and tinydrm. To fix this, introduce a new
drm_atomic_helper_shutdown() by extracting the code from i915.
While at it improve kernel-doc and catch future offenders by
sprinkling a WARN_ON into the legacy function. We should probably move
those into the legacy modeset helpers, too ...
v2: Make it compile on arm drivers too (Noralf).
v3: Correct kerneldoc to point at _disable_all().
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Acked-by: Noralf Trønnes <noralf@tronnes.org>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Cc: Noralf Trønnes <noralf@tronnes.org>
Cc: Ben Skeggs <bskeggs@redhat.com>
Tested-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170321164149.31531-1-daniel.vetter@ffwll.ch
Using KASAN, Dmitry found a bug in the rh_call_control() routine: If
buffer allocation fails, the routine returns immediately without
unlinking its URB from the control endpoint, eventually leading to
linked-list corruption.
This patch fixes the problem by jumping to the end of the routine
(where the URB is unlinked) when an allocation failure occurs.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reported-and-tested-by: Dmitry Vyukov <dvyukov@google.com>
CC: <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This resolves a merge issue in the gadget code, and we want the USB
fixes in here as well.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch converts x86 to use proper folding of a new (fifth) page table level
with <asm-generic/pgtable-nop4d.h>.
That's a bit of a kitchen sink patch, but I don't see how to split it further
without hurting bisectability.
Signed-off-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Andy Lutomirski <luto@amacapital.net>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Brian Gerst <brgerst@gmail.com>
Cc: Dave Hansen <dave.hansen@intel.com>
Cc: Denys Vlasenko <dvlasenk@redhat.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Josh Poimboeuf <jpoimboe@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Michal Hocko <mhocko@suse.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: linux-arch@vger.kernel.org
Cc: linux-mm@kvack.org
Link: http://lkml.kernel.org/r/20170317185515.8636-7-kirill.shutemov@linux.intel.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Split these helpers into a couple of per-level functions and add support for
an additional page table level.
Signed-off-by: Xiong Zhang <xiong.y.zhang@intel.com>
[ Split off into separate patch ]
Signed-off-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Andy Lutomirski <luto@amacapital.net>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Brian Gerst <brgerst@gmail.com>
Cc: Dave Hansen <dave.hansen@intel.com>
Cc: Denys Vlasenko <dvlasenk@redhat.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Josh Poimboeuf <jpoimboe@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Michal Hocko <mhocko@suse.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: linux-arch@vger.kernel.org
Cc: linux-mm@kvack.org
Link: http://lkml.kernel.org/r/20170317185515.8636-6-kirill.shutemov@linux.intel.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
drm_driver.fops can't be shared since the owner then becomes tinydrm.ko.
Move the fops declaration to the driver.
v2: Use DEFINE_DRM_GEM_CMA_FOPS
Reported-by: Daniel Vetter <daniel.vetter@intel.com>
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/20170326142529.16938-1-noralf@tronnes.org
Currently, the irq handler that monitors changes for HPD and RX_SENSE
relies on the status of the bridge for updating the status of the HPD.
The update is done only when the bridge is enabled.
However, on Rockchip platforms we have found use cases where it could be
a problem. When HDMI is being used, turning off/on the screen or
unplugging/re-plugging the cable, the following simplified code path
will happen:
- dw_hdmi_irq() will be triggered by an HPD event, as the bridge is on
hdmi->disabled is false, then the handler will update the rxsense flag
accordingly.
- dw_hdmi_update_power() will be invoked with the mode
DRM_FORCE_UNSPECIFIED and rxsense == 1, so dw_hdmi_poweroff() will be
called and the PHY will be desactivated (its pixel clocks and TMDS)
[...]
- dw_hdmi_bridge_disable() will be invoked, the bridge will be marked as
disabled.
- dw_hdmi_irq() will be triggered by an HPD event, as the bridge is
currently disabled the HPD status won't be updated, so hdmi->rxsense
won't be changed. Even if the data part of the PHY is disabled, this
information coming from the HDMI Transmitter is correct and should be
saved.
[...]
- dw_hdmi_bridge_enable() will be invoked, the bridge will be marked as
enabled.
- dw_hdmi_update_power() will be called. When hdmi->force is equal to
DRM_FORCE_UNSPECIFIED the function will rely on hdmi->rxsense. If this
field has not been updated by the irq handler, it will be false and
DRM_FORCE_ON won't be put to hdmi->force.
Consequently, most of the time dw_hdmi_poweron() won't be called in this
use case, TMDS won't be re-enabled the PHY won't be re-initialized,
resulting in a "Signal not found".
This commit fixes the issue by removing the check for "!hdmi->disabled".
As already explained, even if the PHY is partially disabled, information
coming from HDMI Transmitter about HPD should be saved for a later use.
Signed-off-by: Romain Perier <romain.perier@collabora.com>
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Link: https://patchwork.freedesktop.org/patch/143602/
sdma_disable_channel() cannot ensure dma is stopped to access
module's FIFOs. There is chance SDMA core is running and accessing
BD when disable of corresponding channel, this may cause sometimes
even after call of .sdma_disable_channel(), SDMA core still be
running and accessing module's FIFOs.
According to NXP R&D team a delay of one BD SDMA cost time (maximum
is 1ms) should be added after disable of the channel bit, to ensure
SDMA core has really been stopped after SDMA clients call
.device_terminate_all.
This patch introduces adds a new function sdma_disable_channel_with_delay()
which simply adds 1ms delay after call sdma_disable_channel(),
and set it as .device_terminate_all.
Signed-off-by: Jiada Wang <jiada_wang@mentor.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
This makes the error handling much more simpler than open-coding
everything and in addition makes the probe function smaller an tidier.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
It makes sense to set residue when channel is in progress. Otherwise it
should be 0 since transfer is completed. Meanwhile this patch doesn't
prevent to set residue value anyway.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
We need to ensure that all DMAs and interrupts are cleared during
shutdown operation in order for kexec to start the next kernel clearly.
Otherwise, HW could be performing a DMA into random addresses in the
middle of second kernel start.
Signed-off-by: Sinan Kaya <okaya@codeaurora.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>