It seems on later Armada 38x, the slot clock configuration bit is not
read-only, but can be written. This means that our RW1C protection ends up
clearing this bit when the link control register is written.
Adjust the mask so that we only avoid writing '1' bits to the RW1C bits of
this register (bits 15 and 14 of the link status) rather than masking out
all the status register bits.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Symbolic permissions 'S_IWUSR | S_IRUGO' are not preferred. Consider using
octal permissions '0644'. Found running checkpatch.
Signed-off-by: Olivier Leveque <o_leveque@orange.fr>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Fixes three checkpatch warnings due to braces used when single
statements are sufficient.
Signed-off-by: Mark Stenglein <mark@stengle.in>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Standard deviation is calculated as the square root of the variance
where variance is the mean of sample_sum and length. Correct the
computation of statP->stddev in accordance to the proper calculation.
Fixes: 3c97c08b57 ("staging: iio: add TAOS tsl2x7x driver")
Reported-by: Abhiram Balasubramanian <abhiram@cs.utah.edu>
Signed-off-by: Eva Rachel Retuya <eraretuya@gmail.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
The payload->header.type and payload->size are little-endian, so just
convert them to the right byte order.
Signed-off-by: Jason Yan <yanaijie@huawei.com>
Cc: <stable@vger.kernel.org> #v4.10+
Signed-off-by: Shaohua Li <shli@fb.com>
discard request doesn't have data attached, so it's meaningless to
allocate memory and copy from original bio for behind IO. And the copy
is bogus because bio_copy_data_partial can't handle discard request.
We don't support writesame/writezeros request so far.
Reviewed-by: Ming Lei <tom.leiming@gmail.com>
Signed-off-by: Shaohua Li <shli@fb.com>
The gyroscope chip might need to be reset to be used.
Without the chip being reset, the driver stopped at the first
regmap_read (to get the CHIP_ID) and failed to probe.
The datasheet of the gyroscope says that a minimum wait of 30ms after
the reset has to be done.
This patch has been checked on a BMX055 and the datasheet of the BMG160
and the BMI055 give the same reset register and bits.
Signed-off-by: Quentin Schulz <quentin.schulz@free-electrons.com>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Environmental humidity sensor is a hid defined sensor,
it shows raw humidity measurement of air.
More information can be found in:
http://www.usb.org/developers/hidpage/HUTRR39b.pdf
According to IIO ABI definition, humidityrelative data output unit is
milli percent. Add the unit convert from percent to milli percent.
Signed-off-by: Song Hongyan <hongyan.song@intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Scale value include two parts: unit conversion and exponent conversion.
Add gravity unit convert table to fix gravity sensor scale value not
right issue.
Signed-off-by: Song Hongyan <hongyan.song@intel.com>
Acked-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
This patch adds support for STMicro VL6180 - ALS, range and proximity sensor. Sensor is capable of measuring the light
intensity as well as object distance using TOF (Time of Flight) technology.
Signed-off-by: Manivannan Sadhasivam <manivannanece23@gmail.com>
Signed-off-by: Peter Meerwald-Stadler <pmeerw@pmeerw.net>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
commit c18a1e0(block: introduce bio_clone_bioset_partial()) introduced
bio_clone_bioset_partial() for raid1 write behind IO. Now the write behind is
rewritten by Ming. We don't need the API any more, so revert the commit.
Cc: Christoph Hellwig <hch@lst.de>
Reviewed-by: Jens Axboe <axboe@fb.com>
Reviewed-by: Ming Lei <tom.leiming@gmail.com>
Signed-off-by: Shaohua Li <shli@fb.com>
Remove the extra parenthesis remove the checkpatch issue.
Signed-off-by: Arushi Singhal <arushisinghal19971997@gmail.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Use resourced managed function devm_iio_triggered_buffer_setup
to make error path simpler and be able to get rid of the remove
function.
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
The cros_ec_sensors_read function must return the type of value on all
cases. This was always true except for RAW and CALIBBIAS data which
returned an error or 0. This patch just fixes the mistake I introduced
when submitting the series.
Fixes: commit c14dca07a3 (iio: cros_ec_sensors: add ChromeOS EC
Contiguous Sensors driver)
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
This patch adds calibration for the Meson SAR ADC.
Points 25% vref and 75% vref are used for calibration.
It uses a simple linear calibration function: SCALE * val + BIAS
Successfully tested on a Odroid C2.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Tested-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
This patch allow write data to normal file when writting
new checkpoint.
We relax three limitations for write_begin path:
1. data allocation
2. node allocation
3. variables in checkpoint
Signed-off-by: Yunlei He <heyunlei@huawei.com>
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
While commit 5523662edd ("Input: add userio module") added userio.h
under the uapi/ directory, it forgot to add the header file to Kbuild.
Thus, the file was missing from header installation.
Signed-off-by: Naohiro Aota <naota@elisp.net>
Reviewed-by: Lyude Paul <thatslyude@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
llvm can optimize the 'if (ptr > data_end)' checks to be in the order
slightly different than the original C code which will confuse verifier.
Like:
if (ptr + 16 > data_end)
return TC_ACT_SHOT;
// may be followed by
if (ptr + 14 > data_end)
return TC_ACT_SHOT;
while llvm can see that 'ptr' is valid for all 16 bytes,
the verifier could not.
Fix verifier logic to account for such case and add a test.
Reported-by: Huapeng Zhou <hzhou@fb.com>
Fixes: 969bf05eb3 ("bpf: direct packet access")
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Martin KaFai Lau <kafai@fb.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We got a report of yet another bug in ping
http://www.openwall.com/lists/oss-security/2017/03/24/6
->disconnect() is not called with socket lock held.
Fix this by acquiring ping rwlock earlier.
Thanks to Daniel, Alexander and Andrey for letting us know this problem.
Fixes: c319b4d76b ("net: ipv4: add IPPROTO_ICMP socket kind")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Daniel Jiang <danieljiang0415@gmail.com>
Reported-by: Solar Designer <solar@openwall.com>
Reported-by: Andrey Konovalov <andreyknvl@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Alexander Duyck says:
====================
Add busy poll support for epoll
This patch set adds support for using busy polling with epoll. The main
idea behind this is that we record the NAPI ID for the last event that is
moved onto the ready list for the epoll context and then when we no longer
have any events on the ready list we begin polling with that ID. If the
busy polling does not yield any events then we will reset the NAPI ID to 0
and wait until a new event is added to the ready list with a valid NAPI ID
before we will resume busy polling.
Most of the changes in this set authored by me are meant to be cleanup or
fixes for various things. For example, I am trying to make it so that we
don't perform hash look-ups for the NAPI instance when we are only working
with sender_cpu and the like.
At the heart of this set is the last 3 patches which enable epoll support
and add support for obtaining the NAPI ID of a given socket. With these it
becomes possible for an application to make use of epoll and get optimal
busy poll utilization by stacking multiple sockets with the same NAPI ID on
the same epoll context.
v1: The first version of this series only allowed epoll to busy poll if all
of the sockets with a NAPI ID shared the same NAPI ID. I feel we were
too strict with this requirement, so I changed the behavior for v2.
v2: The second version was pretty much a full rewrite of the first set. The
main changes consisted of pulling apart several patches to better
address the need to clean up a few items and to make the code easier to
review. In the set however I went a bit overboard and was trying to fix
an issue that would only occur with 500+ years of uptime, and in the
process limited the range for busy_poll/busy_read unnecessarily.
v3: Split off the code for limiting busy_poll and busy_read into a separate
patch for net.
Updated patch that changed busy loop time tracking so that it uses
"local_clock() >> 10" as we originally did.
Tweaked "Change return type.." patch by moving declaration of "work"
inside the loop where is was accessed and always reset to 0.
Added "Acked-by" for patches that received acks.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
This socket option returns the NAPI ID associated with the queue on which
the last frame is received. This information can be used by the apps to
split the incoming flows among the threads based on the Rx queue on which
they are received.
If the NAPI ID actually represents a sender_cpu then the value is ignored
and 0 is returned.
Signed-off-by: Sridhar Samudrala <sridhar.samudrala@intel.com>
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds busy poll support to epoll. The implementation is meant to
be opportunistic in that it will take the NAPI ID from the last socket
that is added to the ready list that contains a valid NAPI ID and it will
use that for busy polling until the ready list goes empty. Once the ready
list goes empty the NAPI ID is reset and busy polling is disabled until a
new socket is added to the ready list.
In addition when we insert a new socket into the epoll we record the NAPI
ID and assume we are going to receive events on it. If that doesn't occur
it will be evicted as the active NAPI ID and we will resume normal
behavior.
An application can use SO_INCOMING_CPU or SO_REUSEPORT_ATTACH_C/EBPF socket
options to spread the incoming connections to specific worker threads
based on the incoming queue. This enables epoll for each worker thread
to have only sockets that receive packets from a single queue. So when an
application calls epoll_wait() and there are no events available to report,
busy polling is done on the associated queue to pull the packets.
Signed-off-by: Sridhar Samudrala <sridhar.samudrala@intel.com>
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move the core functionality in sk_busy_loop() to napi_busy_loop() and
make it independent of sk.
This enables re-using this function in epoll busy loop implementation.
Signed-off-by: Sridhar Samudrala <sridhar.samudrala@intel.com>
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch flips the logic we were using to determine if the busy polling
has timed out. The main motivation for this is that we will need to
support two different possible timeout values in the future and by
recording the start time rather than when we would want to end we can focus
on making the end_time specific to the task be it epoll or socket based
polling.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
checking the return value of sk_busy_loop. As there are only a few
consumers of that data, and the data being checked for can be replaced
with a check for !skb_queue_empty() we might as well just pull the code
out of sk_busy_loop and place it in the spots that actually need it.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Instead of defining two versions of skb_mark_napi_id I think it is more
readable to just match the format of the sk_mark_napi_id functions and just
wrap the contents of the function instead of defining two versions of the
function. This way we can save a few lines of code since we only need 2 of
the ifdef/endif but needed 5 for the extra function declaration.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
While working on some recent busy poll changes we found that child sockets
were being instantiated without NAPI ID being set. In our first attempt to
fix it, it was suggested that we should just pull programming the NAPI ID
into the function itself since all callers will need to have it set.
In addition to the NAPI ID change I have dropped the code that was
populating the Rx hash since it was actually being populated in
tcp_get_cookie_sock.
Reported-by: Sridhar Samudrala <sridhar.samudrala@intel.com>
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch is a cleanup/fix for NAPI IDs following the changes that made it
so that sender_cpu and napi_id were doing a better job of sharing the same
location in the sk_buff.
One issue I found is that we weren't validating the napi_id as being valid
before we started trying to setup the busy polling. This change corrects
that by using the MIN_NAPI_ID value that is now used in both allocating the
NAPI IDs, as well as validating them.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
aarch64-linux-gcc-7 complains about code it doesn't fully understand:
drivers/infiniband/hw/qib/qib_iba7322.c: In function 'qib_7322_txchk_change':
include/asm-generic/bitops/non-atomic.h:105:35: error: 'shadow' may be used uninitialized in this function [-Werror=maybe-uninitialized]
The code is right, and despite trying hard, I could not come up with a version
that I liked better than just adding a fake initialization here to shut up the
warning.
Fixes: f931551baf ("IB/qib: Add new qib driver for QLogic PCIe InfiniBand adapters")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Ira Weiny <ira.weiny@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
blk_integrity_profile's are never modified, so mark them 'const' so that
they are placed in .rodata and benefit from memory protection.
Signed-off-by: Eric Biggers <ebiggers@google.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
When the rdma device is removed, we must cleanup all
the rdma resources within the DEVICE_REMOVAL event
handler to let the device teardown gracefully. When
this happens with live I/O, some memory regions are
occupied. Thus, track them too and dereg all the mr's.
We are safe with mr access by iscsi_iser_cleanup_task.
Reported-by: Raju Rangoju <rajur@chelsio.com>
Signed-off-by: Sagi Grimberg <sagi@grimberg.me>
Reviewed-by: Max Gurtovoy <maxg@mellanox.com>
Reviewed-by: Max Gurtovoy <maxg@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
When testing the epoll w/ busy poll code I found that I could get into a
state where the i40e driver had q_vectors w/ active NAPI that had no rings.
This was resulting in a divide by zero error. To correct it I am updating
the driver code so that we only support NAPI on q_vectors that have 1 or
more rings allocated to them.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Unfortunately too many devices (not under our control) use tcp_tw_recycle=1,
which depends on timestamps being identical of the same saddr.
Although tcp_tw_recycle got removed in net-next we can't make
such end hosts disappear so downgrade to per-host timestamp offsets.
Cc: Soheil Hassas Yeganeh <soheil@google.com>
Cc: Eric Dumazet <edumazet@google.com>
Cc: Neal Cardwell <ncardwell@google.com>
Cc: Yuchung Cheng <ycheng@google.com>
Reported-by: Yvan Vanrossomme <yvan@vanrossomme.net>
Fixes: 95a22caee3 ("tcp: randomize tcp timestamp offsets for each connection")
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
This workqueue is used by our storage target mode ULPs
via the new CQ API. Recent observations when working
with very high-end flash storage devices reveal that
UNBOUND workqueue threads can migrate between cpu cores
and even numa nodes (although some numa locality is accounted
for).
While this attribute can be useful in some workloads,
it does not fit in very nicely with the normal
run-to-completion model we usually use in our target-mode
ULPs and the block-mq irq<->cpu affinity facilities.
The whole block-mq concept is that the completion will
land on the same cpu where the submission was performed.
The fact that our submitter thread is migrating cpus
can break this locality.
We assume that as a target mode ULP, we will serve multiple
initiators/clients and we can spread the load enough without
having to use unbound kworkers.
Also, while we're at it, expose this workqueue via sysfs which
is harmless and can be useful for debug.
Signed-off-by: Sagi Grimberg <sagi@grimberg.me>
Reviewed-by: Bart Van Assche <bart.vanassche@sandisk.com>--
Signed-off-by: Doug Ledford <dledford@redhat.com>
Saeed Mahameed says:
====================
Mellanox mlx5e XDP performance optimization
This series provides some preformancee optimizations for mlx5e
driver, especially for XDP TX flows.
1st patch is a simple change of rmb to dma_rmb in CQE fetch routine
which shows a huge gain for both RX and TX packet rates.
2nd patch removes write combining logic from the driver TX handler
and simplifies the TX logic while improving TX CPU utilization.
All other patches combined provide some refactoring to the driver TX
flows to allow some significant XDP TX improvements.
More details and performance numbers per patch can be found in each patch
commit message compared to the preceding patch.
Overall performance improvemnets
System: Intel(R) Xeon(R) CPU E5-2620 v3 @ 2.40GHz
Test case Baseline Now improvement
---------------------------------------------------------------
TX packets (24 threads) 45Mpps 54Mpps 20%
TC stack Drop (1 core) 3.45Mpps 3.6Mpps 5%
XDP Drop (1 core) 14Mpps 16.9Mpps 20%
XDP TX (1 core) 10.4Mpps 13.7Mpps 31%
====================
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Different SQ types (tx, xdp, ico) are growing apart, we separate them
and remove unwanted parts in each one of them, to simplify data path and
utilize data cache.
Remove DB union from SQ structures since it is not needed anymore as we
now have different SQ data type for each SQ.
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Reviewed-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the next patches we will introduce different SQ types,
and we would want to reuse those functions, in this patch we make them
agnostic to SQ type (txq, xdp, ico).
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Reviewed-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rename mlx5e_{create,destroy}_{sq,rq,cq} to
mlx5e_{alloc,free}_{sq,rq,cq}.
Rename mlx5e_{enable,disable}_{sq,rq,cq} to
mlx5e_{create,destroy}_{sq,rq,cq}.
mlx5e_{enable,disable}_{sq,rq,cq} used to actually create/destroy the SQ
in FW, so we rename them to align the functions names with FW semantics.
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Reviewed-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the next patches we will introduce different SQ types, for that we here
generalize some TX helper functions to work with more basic SQ parameters,
in order to re-use them for the different SQ types.
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Reviewed-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
XDP SQ has a fixed size WQE (MLX5E_XDP_TX_WQEBBS = 1) and only posts
one kind of WQE (MLX5_OPCODE_SEND),
Also we initialize SQ descriptors static fields once on open_xdpsq,
rather than every time on critical path.
Optimize the code in light of those facts and add a prefetch of the TX
descriptor first thing in the xdp xmit function.
Performance improvement:
System: Intel(R) Xeon(R) CPU E5-2620 v3 @ 2.40GHz
Test case Before Now improvement
---------------------------------------------------------------
XDP TX (1 core) 13Mpps 13.7Mpps 5%
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Reviewed-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Handle XDP TX completions before handling RX packets, to make sure more
free space is available for XDP TX packets a moment before handling
RX packets.
Performance improvement:
System: Intel(R) Xeon(R) CPU E5-2620 v3 @ 2.40GHz
Test case Before Now improvement
---------------------------------------------------------------
XDP Drop (1 core) 16.9Mpps 16.9Mpps No change
XDP TX (1 core) 12Mpps 13Mpps 8%
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Reviewed-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
To save many rq->channel->sq dereferences in fast-path.
And rename it to xdpsq.
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Reviewed-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move struct mlx5e_rq and friends to appear after mlx5e_sq declaration in
en.h.
We will need this for next patch to move the mlx5e_sq instance into
mlx5e_rq struct for XDP SQs.
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Reviewed-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
XDP code belongs to RX path, move mlx5e_poll_xdp_tx_cq and
mlx5e_free_xdp_tx_descs to en_rx.c.
Rename them to mlx5e_poll_xdpsq_cq and mlx5e_free_xdpsq_descs.
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Reviewed-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
One is sufficient since Blue Flame is not supported anymore.
This will also come in handy for switchdev mode to save resources, since
VF representors will use same single UAR as well for their own SQs.
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Reviewed-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
mlx5e netdev Blue Flame (write combining) support demands a lot of
overhead for a little latency gain for some special cases, this overhead
is hurting the common case.
Here we remove xmit Blue Flame support by creating all bfregs with no
write combining for all SQs, and we remove a lot of BF logic and
conditions from xmit data path.
Simplify mlx5e_tx_notify_hw (doorbell function) by removing BF related
code and by removing one memory barrier needed for WC mapped SQ doorbell
buffers, which no longer exist.
Performance improvement:
System: Intel(R) Xeon(R) CPU E5-2620 v3 @ 2.40GHz
Test case Before Now improvement
---------------------------------------------------------------
TX packets (24 threads) 50Mpps 54Mpps 8%
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Reviewed-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use dma_rmb in mlx5e_get_cqe rather than aggressive rmb (at least on
some architectures), this should help improve the performance on such
CPU archs where dma_rmb is optimized.
Performance improvement:
System: Intel(R) Xeon(R) CPU E5-2620 v3 @ 2.40GHz
Test case Baseline Now improvement
---------------------------------------------------------------
TX packets (24 threads) 45Mpps 50Mpps 11%
TC stack Drop (1 core) 3.45Mpps 3.6Mpps 5%
XDP Drop (1 core) 14Mpps 16.9Mpps 20%
XDP TX (1 core) 10.4Mpps 12Mpps 15%
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Reviewed-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
According to C9-147, MSN should only be incremented when the last packet of
a multi packet request has been received.
"Logically, the requester associates a sequential Send Sequence Number
(SSN) with each WQE posted to the send queue. The SSN bears a one-
to-one relationship to the MSN returned by the responder in each re-
sponse packet. Therefore, when the requester receives a response, it in-
terprets the MSN as representing the SSN of the most recent request
completed by the responder to determine which send WQE(s) can be
completed."
Fixes: 8700e3e7c4 ("Soft RoCE driver")
Signed-off-by: David Marchand <david.marchand@6wind.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Consistently use types from linux/types.h to fix the following
rdma/mlx5-abi.h userspace compilation errors:
/usr/include/rdma/mlx5-abi.h:69:25: error: 'u64' undeclared here (not in a function)
MLX5_LIB_CAP_4K_UAR = (u64)1 << 0,
/usr/include/rdma/mlx5-abi.h:69:29: error: expected ',' or '}' before numeric constant
MLX5_LIB_CAP_4K_UAR = (u64)1 << 0,
Include <linux/if_ether.h> to fix the following rdma/mlx5-abi.h
userspace compilation error:
/usr/include/rdma/mlx5-abi.h:286:12: error: 'ETH_ALEN' undeclared here (not in a function)
__u8 dmac[ETH_ALEN];
Signed-off-by: Dmitry V. Levin <ldv@altlinux.org>
Signed-off-by: Doug Ledford <dledford@redhat.com>