This removes the "0x" prefix in front of the I2C DT device
address designation for each I2C DT node in the ux500
devicetree files.
Reported-by: Bryan Wu <cooloney@gmail.com>
Cc: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
As it stands, the memory node in the u8540 Device Tree is ignored and
memory is actually stipulated by the bootloader via ATAGS. ARM core
architecture code then extracts the memory ATAG and inserts it into the
Device Tree. In the u8540 the LittleKernel bootloader only stipulates
512MB of memory; however, the u8540 actually has 2GB. We're taking the
responsibility to register the remainder from Device Tree here.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Ux500 ASoC driver is expected to have a specific device name to get
clock resources correctly. This patch provides the necessary
OF_DEV_AUXDATA to match the name in DT and non-DT cases.
Signed-off-by: Fabio Baltieri <fabio.baltieri@linaro.org>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add regulator DT bindings for the ab8500-codec driver.
Signed-off-by: Fabio Baltieri <fabio.baltieri@linaro.org>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Fix typo of VAMIC2 LDO regulator name in some DT-related files. This
patch replaces all occurrences with the right name.
Signed-off-by: Fabio Baltieri <fabio.baltieri@linaro.org>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Fix VAMIC1 LDO comment in DT files to be make it coherent with the
others.
Signed-off-by: Fabio Baltieri <fabio.baltieri@linaro.org>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
After some discussion and deliberation we have decided to only use the
short form of the PRCMU register names i.e. not mention the peripheral
in which the registers reside.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The recently DT:ed MUSB driver will require clock-name by device-name
look-up capability, until common clk has is properly supported by the
ux500 platform.
Acked-by: Fabio Baltieri <fabio.baltieri@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
What GPIO pin is used with which device on the SSP/SPI bus
is as board-specific as it gets, so it does not belong here
in the core SoC file, and it is disabled so it doesn't hurt
to delete this.
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This switches to including <dt-bindings/interrupt-controller/irq.h>
and referencing the apropriate flags from there instead of
open-coding the flag numerals everywhere in the ux500 device
trees.
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This patch prepares the use of '#define' into dts files.
Signed-off-by: Gabriel Fernandez <gabriel.fernandez@st.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
In patch:
"ARM: ux500: Enable 100MHz for SD/SDIO/MMC devices"
the max frequency for the MMC/SD/SDIO adapters was
increased from 50 to 100MHz. Do the same for the
device tree boot path.
Cc: Lee Jones <lee.jones@linaro.org>
Cc: Gabriel Fernandez <gabriel.fernandez.st@gmail.com>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Devices in board DTS files are usually searchable by multiple
compatible strings. In this case the 8540 based SoC should be
obtainable via the chipset [DB8540 & AB8540] name 'u8540' or
the board name 'ccu8540'. It's already possible to obtain the
Device Tree via its chipset name, this patch makes it possible
to get it by its board name too.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
By providing an OF match table with a suitable compatible string, we
can ensure the ux500-hasht driver is probed by supplying an associated
DT node in a given platform's Device Tree.
Cc: linux-crypto@vger.kernel.org
Acked-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
By providing an OF match table with a suitable compatible string, we
can ensure the ux500-crypt driver is probed by supplying an associated
DT node in a given platform's Device Tree.
Cc: linux-crypto@vger.kernel.org
Acked-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Commits:
"ARM: ux500: Add Device Tree nodes for the ux500 Crypt device"
"ARM: ux500: Add Device Tree nodes for the ux500 Hash device"
Added the crypto and hash devices conditionally, i.e. so as to
be turned on per-board by setting an "status" property on the
device from "disabled" to "okay" on each device.
This is wrong since this is an SoC feature, it is not board
dependent. It is the same ASIC under all circumstances and
functionality does not vary with board family.
This moves the enablement into the SoC file.
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This provides a device name which is required by the common clk API.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This provides a device name which is required by the common clk API.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
[Edited patch subject]
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This patch provides information required to setup ux500-hash when
booting with DT on the Snowball low-cost development platform.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This patch provides information required to setup ux500-crypt when
booting with DT on the Snowball low-cost development platform.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Based on pending device tree support in the LP55xx drivers
we can add the correct LED and channel configuration from the
ux500 device tree for all HREF variants.
Cc: Bryan Wu <cooloney@gmail.com>
Acked-by: Milo Kim <Milo.Kim@ti.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The Rohm vendor name was twisted in the STUIB device tree
include file. Fix it up.
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This makes sure the new ccu8540 DTB file is generated by
the build system.
Cc: Lee Jones <lee.jones@linaro.org>
Cc: Gabriel Fernandez <gabriel.fernandez.st@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The PRCMU's Tightly Coupled Data Memory on the DB8540 platform is
8kB larger than it's predecessor's. We need to reflect that in its
Device Tree. By re-specifying the address and size of the device
we effectively over-ride the previous values with more accurate
ones.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This is a skeleton DTS file which only enables serial. Just using
this simple file yields a terminal when booting u8540.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
It's now possible to configure memcpy channels dynamically with DT.
We're providing them despite the fact that they're the same as the
hard-coded channels, as they will be removed once the u8500 platform
goes DT-only.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This patch provides all the information to successfully probe() and
correctly configure the ux500-musb device driver for DMA.
Acked-by: Fabio Baltieri <fabio.baltieri@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
When requesting a channel, a DMA client needs to pass some pieces of
information such as; request channel, device type, channel type and
direction etc. Normally we do this in the form of platform data, but
when DT is enabled we need to pass it using the driver's bindings
instead.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
When requesting a channel, a DMA client needs to pass some pieces of
information such as; request channel, device type, channel type and
direction etc. Normally we do this in the form of platform data, but
when DT is enabled we need to pass it using the driver's bindings
instead.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The new DMA is now available, so let's use it to setup ST-Ericsson's
DMA40 driver when Device Tree is enabled.
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The DMA40 controller uses two sets of base addresses. In order to have
the resources setup by the of_platform framework so they are searchable
by name instead of index, we have to set names for them. The names have
to be the same as the ones used to fetch them back out of the resource
structure.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Ux500 regulator name for V-INTCORE is misspelled as vinitcore instead of
vintcore in some .dts file, causing the AB8500 regulator driver to not
bind properly. Fix this by replacing all occurrences with the right
name.
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Fabio Baltieri <fabio.baltieri@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This root node is used in the whole family of chips, the a9500
is just one particular instance. Nodes should be named after
the type of object rather than identity.
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Gabriel Fernandez <gabriel.fernandez@stericsson.com>
Reviewed-by: Philippe Langlais <philippe.langlais@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Until recently platform code took care of all MMCI level-shifting by
way of an ios_handler() call-back. Now it is the driver's responsibility
to handle. In order to so that we need to provide the VQMMC regulator
reference in Device Tree. This patch takes care of that.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
If we attempt to use the existing u8500 of_dev_auxdata struct to boot
the u8540, we fail to obtain a console, due to a lack of DMA support
on the platform.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
When the thermal DT node was inserted a new PRCMU node was created;
however, one already exists in the Snowball DTS file. Here we
amalgamate the two into a single consolidated node.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
do_smart_update_queue() is called when an operation (semop,
semctl(SETVAL), semctl(SETALL), ...) modified the array. It must check
which of the sleeping tasks can proceed.
do_smart_update_queue() missed a few wakeups:
- if a sleeping complex op was completed, then all per-semaphore queues
must be scanned - not only those that were modified by *sops
- if a sleeping simple op proceeded, then the global queue must be
scanned again
And:
- the test for "|sops == NULL) before scanning the global queue is not
required: If the global queue is empty, then it doesn't need to be
scanned - regardless of the reason for calling do_smart_update_queue()
The patch is not optimized, i.e. even completing a wait-for-zero
operation causes a rescan. This is done to keep the patch as simple as
possible.
Signed-off-by: Manfred Spraul <manfred@colorfullife.com>
Acked-by: Davidlohr Bueso <davidlohr.bueso@hp.com>
Cc: Rik van Riel <riel@redhat.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
- Stable fix to prevent an rpc_task wakeup race
- Fix a NFSv4.1 session drain deadlock
- Fix a NFSv4/v4.1 mount regression when not running rpc.gssd
- Ensure auth_gss pipe detection works in namespaces
- Fix SETCLIENTID fallback if rpcsec_gss is not available
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.13 (GNU/Linux)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=B8go
-----END PGP SIGNATURE-----
Merge tag 'nfs-for-3.10-3' of git://git.linux-nfs.org/projects/trondmy/linux-nfs
Pull NFS client bugfixes from Trond Myklebust:
- Stable fix to prevent an rpc_task wakeup race
- Fix a NFSv4.1 session drain deadlock
- Fix a NFSv4/v4.1 mount regression when not running rpc.gssd
- Ensure auth_gss pipe detection works in namespaces
- Fix SETCLIENTID fallback if rpcsec_gss is not available
* tag 'nfs-for-3.10-3' of git://git.linux-nfs.org/projects/trondmy/linux-nfs:
NFS: Fix SETCLIENTID fallback if GSS is not available
SUNRPC: Prevent an rpc_task wakeup race
NFSv4.1 Fix a pNFS session draining deadlock
SUNRPC: Convert auth_gss pipe detection to work in namespaces
SUNRPC: Faster detection if gssd is actually running
SUNRPC: Fix a bug in gss_create_upcall
Pull parisc fixes from Helge Deller:
"This time we made the kernel- and interruption stack allocation
reentrant which fixed some strange kernel crashes (specifically
protection ID traps).
Furthemore this patchset fixes the interrupt stack in UP and SMP
configurations by using native locking instructions. And finally
usage of floating point calculations on parisc were disabled in the
MPILIB."
* 'parisc-for-3.10' of git://git.kernel.org/pub/scm/linux/kernel/git/deller/parisc-linux:
parisc: fix irq stack on UP and SMP
parisc/superio: Use module_pci_driver to register driver
parisc: make interrupt and interruption stack allocation reentrant
parisc: show number of FPE and unaligned access handler calls in /proc/interrupts
parisc: add additional parisc git tree to MAINTAINERS file
parisc: use PAGE_SHIFT instead of hardcoded value 12 in pacache.S
parisc: add rp5470 entry to machine database
MPILIB: disable usage of floating point registers on parisc
- Fix for corruption with FSX on 512 byte blocksize filesystems
- Fix rounding error in xfs_free_file_space
- Fix use-after-free with extent free intents
- Add several missing KM_NOFS flags to fix lockdep reports
- Several fixes for CRC related code
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.10 (GNU/Linux)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=hQCM
-----END PGP SIGNATURE-----
Merge tag 'for-linus-v3.10-rc3' of git://oss.sgi.com/xfs/xfs
Pull xfs fixes from Ben Myers:
"Here are fixes for corruption on 512 byte filesystems, a rounding
error, a use-after-free, some flags to fix lockdep reports, and
several fixes related to CRCs. We have a somewhat larger post -rc1
queue than usual due to fixes related to the CRC feature we merged for
3.10:
- Fix for corruption with FSX on 512 byte blocksize filesystems
- Fix rounding error in xfs_free_file_space
- Fix use-after-free with extent free intents
- Add several missing KM_NOFS flags to fix lockdep reports
- Several fixes for CRC related code"
* tag 'for-linus-v3.10-rc3' of git://oss.sgi.com/xfs/xfs:
xfs: remote attribute lookups require the value length
xfs: xfs_attr_shortform_allfit() does not handle attr3 format.
xfs: xfs_da3_node_read_verify() doesn't handle XFS_ATTR3_LEAF_MAGIC
xfs: fix missing KM_NOFS tags to keep lockdep happy
xfs: Don't reference the EFI after it is freed
xfs: fix rounding in xfs_free_file_space
xfs: fix sub-page blocksize data integrity writes
- Additional CPU ID for the intel_pstate driver from Dirk Brandewie.
- More cpufreq fixes related to ARM big.LITTLE support and locking from
Viresh Kumar.
- VIA C7 cpufreq build fix from Rafał Bilski.
- ACPI power management fix making it possible to use device power
states regardless of the CONFIG_PM setting from Rafael J. Wysocki.
- New ACPI video blacklist item from Bastian Triller.
/
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)
iQIcBAABAgAGBQJRoRZjAAoJEKhOf7ml8uNsv9wQAKAMs9J8k6XqgNPisFKetw+K
hzCOsKFOpI0BQKFikgtWjhGre1SyNIRUvLXO7BHFHXYQW6cLvn1jAyJhvl+i4nvT
eOa+vdGd6grWncbhIxeidoyk9hTZ6bdMWlTBvKUz5KpHzvp4YGC2jlvwFwqsJkpg
nQ8Hcbrbhm4vz5h7EmrlYcELBNTi5LQtmnqlxtbn02GX75BFTpkCm5aLZWZNEUrE
Hix8BhN41+hSy+K34ztHFlP5g/s/lIa9dOX1tewqSigkDB/qYYIt2lpdD2icOIOW
qHAtvpZq8/fZOcoZ9KdFqKUjjbuKVavldb+YzGeTLQufOAwb4hgMRvAccdNFMHIW
9tVkp2TcK6K7pAYlXtgEf25ka7ulLWDBd4C662gZfpi+oPKx2BI/6m7J4VoTULeb
30hDMyZXrXWWvStwO05Pyno3W5lG+cn9jytc3hKkaFerb53NHcZHfb0Rih5NhDZD
Ep09IuPE8fOT9KndY2kw/WwoZyJurYCbrgE+G1QyA+hsNPkNhPlGTxdL8vCqxM4K
ZOaQQejpd1bXBSk8Koz8LRyQ38KJByvM64B0EDSP6BQUT+rlbkcvog1bJV+UdpbJ
4TlhrAFlobhRFQBqlIbRqMXFPH31YSm7wVK1eK/gEqNZI935Kd17YSFf8yyi2yli
vBlmPkiPEIJHysps+tvd
=Srt8
-----END PGP SIGNATURE-----
Merge tag 'pm+acpi-3.10-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management and ACPI fixes from Rafael Wysocki:
- Additional CPU ID for the intel_pstate driver from Dirk Brandewie.
- More cpufreq fixes related to ARM big.LITTLE support and locking from
Viresh Kumar.
- VIA C7 cpufreq build fix from Rafał Bilski.
- ACPI power management fix making it possible to use device power
states regardless of the CONFIG_PM setting from Rafael J Wysocki.
- New ACPI video blacklist item from Bastian Triller.
* tag 'pm+acpi-3.10-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
ACPI / video: Add "Asus UL30A" to ACPI video detect blacklist
cpufreq: arm_big_little_dt: Instantiate as platform_driver
cpufreq: arm_big_little_dt: Register driver only if DT has valid data
cpufreq / e_powersaver: Fix linker error when ACPI processor is a module
cpufreq / intel_pstate: Add additional supported CPU ID
cpufreq: Drop rwsem lock around CPUFREQ_GOV_POLICY_EXIT
ACPI / PM: Allow device power states to be used for CONFIG_PM unset
Pull slave-dma fixes from Vinod Koul:
"We have two patches from Andy & Rafael fixing the Lynxpoint dma"
* 'fixes' of git://git.infradead.org/users/vkoul/slave-dma:
ACPI / LPSS: register clock device for Lynxpoint DMA properly
dma: acpi-dma: parse CSRT to extract additional resources
kcore_vmalloc is in fs/proc/kcore.c and kcore_mem is unused across
the tree. Noticed while grepping the tree for some other kcore stuff.
(score looks pretty unmaintained to me.)
Signed-off-by: Kyle McMartin <kyle@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* Fallouts/wreckage of Cache Flush optimizations / aliasing dcache support
* Fix for an interesting bug where piped input to grep was getting
mysteriously clobbered
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=j1po
-----END PGP SIGNATURE-----
Merge tag 'arc-v3.10-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/vgupta/arc
Pull ARC fixes from Vineet Gupta:
- Fallouts/wreckage of Cache Flush optimizations / aliasing dcache
support
- Fix for an interesting bug where piped input to grep was getting
mysteriously clobbered
* tag 'arc-v3.10-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/vgupta/arc:
ARC: lazy dcache flush broke gdb in non-aliasing configs
ARC: Use enough bits for determining page's cache color
ARC: Brown paper bag bug in macro for checking cache color
ARC: copy_(to|from)_user() to honor usermode-access permissions
ARC: [mm] Prevent stray dcache lines after__sync_icache_dcach()
ARC: [TB10x] Remove redundant abilis,simple-pinctrl mechanism
