[ Upstream commit a8662eadd1 ]
According to the public S805 datasheet HHI_SYS_CPU_CLK_CNTL1[29:20] is
the register for the CPU scale_div clock. This matches the code in
Amlogic's 3.10 GPL kernel sources:
N = (aml_read_reg32(P_HHI_SYS_CPU_CLK_CNTL1) >> 20) & 0x3FF;
This means that the divider register is 10 bit wide instead of 9 bits.
So far this is not a problem since all u-boot versions I have seen are
not using the cpu_scale_div clock at all (instead they are configuring
the CPU clock to run off cpu_in_sel directly).
The fixes tag points to the latest rework of the CPU clocks. However,
even before the rework it was wrong. Commit 7a29a86943 ("clk: meson:
Add support for Meson clock controller") defines MESON_N_WIDTH as 9 (in
drivers/clk/meson/clk-cpu.c). But since the old clk-cpu implementation
this only carries the fixes tag for the CPU clock rewordk.
Fixes: 251b6fd38b ("clk: meson: rework meson8b cpu clock")
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Link: https://lkml.kernel.org/r/20180927085921.24627-3-martin.blumenstingl@googlemail.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a5ac1ead32 ]
The cpu_div3 clock (cpu_in divided by 3) generates a signal with a duty
cycle of 33%. The CPU clock however requires a clock signal with a duty
cycle of 50% to run stable.
cpu_div3 was observed to be problematic when cycling through all
available CPU frequencies (with additional patches on top of this one)
while running "stress --cpu 4" in the background. This caused sporadic
hangs where the whole system would fully lock up.
Amlogic's 3.10 kernel code also does not use the cpu_div3 clock either
when changing the CPU clock.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Reviewed-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Link: https://lkml.kernel.org/r/20181115224048.13511-3-martin.blumenstingl@googlemail.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 63a298f22a ]
The rcar-du driver supports probe deferral for external clocks, but
implements it badly by checking the wrong pointer due to a bad copy and
paste. Fix it.
While at it, reject invalid clocks outright for DU channels that have a
display PLL, as the external clock is mandatory in that case. This
avoids a WARN_ON() at runtime.
Fixes: 1b30dbde85 ("drm: rcar-du: Add support for external pixel clock")
Reported-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 01b671170d ]
When the rdma device is getting removed, get resource info can race with
device removal, as below:
CPU-0 CPU-1
-------- --------
rdma_nl_rcv_msg()
nldev_res_get_cq_dumpit()
mutex_lock(device_lock);
get device reference
mutex_unlock(device_lock); [..]
ib_unregister_device()
/* Valid reference to
* device->dev exists.
*/
ib_dealloc_device()
[..]
provider->fill_res_entry();
Even though device object is not freed, fill_res_entry() can get called on
device which doesn't have a driver anymore. Kernel core device reference
count is not sufficient, as this only keeps the structure valid, and
doesn't guarantee the driver is still loaded.
Similar race can occur with device renaming and device removal, where
device_rename() tries to rename a unregistered device. While this is fine
for devices of a class which are not net namespace aware, but it is
incorrect for net namespace aware class coming in subsequent series. If a
class is net namespace aware, then the below [1] call trace is observed in
above situation.
Therefore, to avoid the race, keep a reference count and let device
unregistration wait until all netlink users drop the reference.
[1] Call trace:
kernfs: ns required in 'infiniband' for 'mlx5_0'
WARNING: CPU: 18 PID: 44270 at fs/kernfs/dir.c:842 kernfs_find_ns+0x104/0x120
libahci i2c_core mlxfw libata dca [last unloaded: devlink]
RIP: 0010:kernfs_find_ns+0x104/0x120
Call Trace:
kernfs_find_and_get_ns+0x2e/0x50
sysfs_rename_link_ns+0x40/0xb0
device_rename+0xb2/0xf0
ib_device_rename+0xb3/0x100 [ib_core]
nldev_set_doit+0x165/0x190 [ib_core]
rdma_nl_rcv_msg+0x249/0x250 [ib_core]
? netlink_deliver_tap+0x8f/0x3e0
rdma_nl_rcv+0xd6/0x120 [ib_core]
netlink_unicast+0x17c/0x230
netlink_sendmsg+0x2f0/0x3e0
sock_sendmsg+0x30/0x40
__sys_sendto+0xdc/0x160
Fixes: da5c850782 ("RDMA/nldev: add driver-specific resource tracking")
Signed-off-by: Parav Pandit <parav@mellanox.com>
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e10b40f330 ]
If you create multiple vivid instances, each with their own media
device, then there was no way to tell them apart.
Fill in the bus_info so each instance has a unique bus_info string.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 51232df5e4 ]
When the managed cache is enabled, the last reference count
of a workgroup must be used for its workstation.
Otherwise, it could lead to incorrect (un)freezes in
the reclaim path, and it would be harmful.
A typical race as follows:
Thread 1 (In the reclaim path) Thread 2
workgroup_freeze(grp, 1) refcnt = 1
...
workgroup_unfreeze(grp, 1) refcnt = 1
workgroup_get(grp) refcnt = 2 (x)
workgroup_put(grp) refcnt = 1 (x)
...unexpected behaviors
* grp is detached but still used, which violates cache-managed
freeze constraint.
Reviewed-by: Chao Yu <yuchao0@huawei.com>
Signed-off-by: Gao Xiang <gaoxiang25@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit eef1687898 ]
It's better not to positively BUG_ON the kernel, however developers
need a way to locate issues as soon as possible.
DBG_BUGON is introduced and it could only crash when EROFS_FS_DEBUG
(EROFS developping feature) is on. It is helpful for developers
to find and solve bugs quickly by eng builds.
Previously, DBG_BUGON is defined as ((void)0) if EROFS_FS_DEBUG is off,
but some unused variable warnings as follows could occur:
drivers/staging/erofs/unzip_vle.c: In function `init_alway:':
drivers/staging/erofs/unzip_vle.c:61:33: warning: unused variable `work' [-Wunused-variable]
struct z_erofs_vle_work *const work =
^~~~
Fix it to #define DBG_BUGON(x) ((void)(x)).
Reviewed-by: Chao Yu <yuchao0@huawei.com>
Signed-off-by: Gao Xiang <gaoxiang25@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8ea0f2ba0f ]
of_parse_phandle() returns the device node with refcount incremented.
There are two nodes that are used temporary in mtk_vcodec_init_enc_pm(),
but their refcounts are not decremented.
The patch adds one of_node_put() and fixes returning error codes.
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c764da98a6 ]
The video device release() callback for video-i2c driver frees the whole
struct video_i2c_data. If there is no user left for the video device
when video_unregister_device() is called, the release callback is executed.
However, in video_i2c_remove() some fields (v4l2_dev, lock, and queue_lock)
in struct video_i2c_data are still accessed after video_unregister_device()
is called.
This fixes the use after free by moving the code from video_i2c_remove()
to the release() callback.
Fixes: 5cebaac609 ("media: video-i2c: add video-i2c driver")
Reviewed-by: Matt Ranostay <matt.ranostay@konsulko.com>
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8e782fcf78 ]
If userspace has an open file descriptor on the rc input device or lirc
device when rc_unregister_device() is called, then the rc close() is
never called.
This ensures that the receiver is turned off on the nuvoton-cir driver
during shutdown.
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9eb40fa2cd ]
of_find_node_by_path() acquires a reference to the node returned by it
and that reference needs to be dropped by its caller. soc_is_tegra()
doesn't do that, so fix it.
Signed-off-by: Yangtao Li <tiny.windzz@gmail.com>
Acked-by: Jon Hunter <jonathanh@nvidia.com>
[treding: slightly rewrite to avoid inline comparison]
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8d0bb86e2c ]
I fixed a bug by adding a dependency in the network driver, but that fix
caused a related bug in the SCSI driver:
WARNING: unmet direct dependencies detected for CHELSIO_T4
Depends on [m]: NETDEVICES [=y] && ETHERNET [=y] && NET_VENDOR_CHELSIO [=y] && PCI [=y] && (IPV6 [=y] || IPV6 [=y]=n) && (THERMAL [=m] || !THERMAL [=m])
Selected by [y]:
- SCSI_CXGB4_ISCSI [=y] && SCSI_LOWLEVEL [=y] && SCSI [=y] && PCI [=y] && INET [=y] && (IPV6 [=y] || IPV6 [=y]=n)
drivers/net/ethernet/chelsio/cxgb4/cxgb4_thermal.o: In function `cxgb4_thermal_init':
cxgb4_thermal.c:(.text+0x158): undefined reference to `thermal_zone_device_register'
drivers/net/ethernet/chelsio/cxgb4/cxgb4_thermal.o: In function `cxgb4_thermal_remove':
cxgb4_thermal.c:(.text+0x1d8): undefined reference to `thermal_zone_device_unregister'
/git/arm-soc/Makefile:1042: recipe for target 'vmlinux' failed
The same dependency needs to be propagated here to make it work correctly
with CONFIG_THERMAL=m and SCSI_CXGB4_ISCSI=y. That change by itself causes
another problem with a circular dependency, as we use 'select NETDEVICES'.
This is something we really should not do anyway, as a driver symbol should
never select another major subsystem, so let's turn that into a 'depends
on'. I don't see any downsides of that, as NETDEVICES is only disabled in
rather obscure cases that are not relevant to the users of cxgb4i.
Fixes: e70a57fa59 ("cxgb4: fix thermal configuration dependencies")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4787eff3fa ]
The tool perf is useful for the performance analysis on the Hygon Dhyana
platform. But right now there is no Hygon support for it to analyze the
KVM guest os data. So add Hygon Dhyana support to it by checking vendor
string to share the code path of AMD.
Signed-off-by: Pu Wen <puwen@hygon.cn>
Acked-by: Borislav Petkov <bp@suse.de>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Jiri Olsa <jolsa@kernel.org>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/1542008451-31735-1-git-send-email-puwen@hygon.cn
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5818c683a6 ]
If an ARM mapping symbol shares an address with a valid symbol,
find_elf_symbol can currently return the mapping symbol instead, as the
symbol is not validated. This can result in confusing warnings:
WARNING: vmlinux.o(.text+0x18f4028): Section mismatch in reference
from the function set_reset_devices() to the variable .init.text:$x.0
This change adds a call to is_valid_name to find_elf_symbol, similarly
to how it's already used in find_elf_symbol2.
Signed-off-by: Sami Tolvanen <samitolvanen@google.com>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1e86ace4c1 ]
Currently the cpu affinity hint mask for completion EQs is stored and
read from the wrong place, since reading and storing is done from the
same index, there is no actual issue with that, but internal irq_info
for completion EQs stars at MLX5_EQ_VEC_COMP_BASE offset in irq_info
array, this patch changes the code to use the correct offset to store
and read the IRQ affinity hint.
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Reviewed-by: Leon Romanovsky <leonro@mellanox.com>
Reviewed-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 23499442c3 ]
Since commit 88cda1c9da ("bpf: libbpf: Provide basic API support
to specify BPF obj name"), libbpf unconditionally sets bpf_attr->name
for maps. Pre v4.14 kernels don't know about map names and return an
error about unexpected non-zero data. Retry sys_bpf without a map
name to cover older kernels.
v2 changes:
* check for errno == EINVAL as suggested by Daniel Borkmann
Signed-off-by: Stanislav Fomichev <sdf@google.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 08e1c28dd5 ]
[why]
phy_pix_clk is one of the variable used to check if one PLL can be shared
with displays having common mode set configuration. As of now
phy_pix_clock varialbe is calculated in function dc_validate_stream().
dc_validate_stream() function is called after clocks are assigned for the
new display. Due to this during hotplug, when PLL sharing conditions are
checked for new display phy_pix_clk variable will be 0 and for displays
that are already enabled phy_pix_clk will have some value. Hence PLL will
not be shared and if the display hardware doesn't have any more PLL to
assign, mode set will fail due to resource unavailability.
[how]
Instead of only calculating the phy_pix_clk variable after the PLL is
assigned for new display, this patch calculates phy_pix_clk also during
the before assigning the PLL for new display.
Signed-off-by: Yogesh Mohan Marimuthu <yogesh.mohanmarimuthu@amd.com>
Reviewed-by: Harry Wentland <Harry.Wentland@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8ce504b938 ]
[why]
Gamma was always being set as identity on SDR monitor,
leading to no changes in gamma. This caused nightlight to
not apply correctly.
[how]
Added a default gamma structure to compare against
in the sdr case.
Signed-off-by: Murton Liu <murton.liu@amd.com>
Reviewed-by: Krunoslav Kovac <Krunoslav.Kovac@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c10b26abeb ]
When building the kernel with Clang, the following section mismatch
warnings appears:
WARNING: vmlinux.o(.text+0x2d398): Section mismatch in reference from
the function _setup() to the function .init.text:_setup_iclk_autoidle()
The function _setup() references
the function __init _setup_iclk_autoidle().
This is often because _setup lacks a __init
annotation or the annotation of _setup_iclk_autoidle is wrong.
WARNING: vmlinux.o(.text+0x2d3a0): Section mismatch in reference from
the function _setup() to the function .init.text:_setup_reset()
The function _setup() references
the function __init _setup_reset().
This is often because _setup lacks a __init
annotation or the annotation of _setup_reset is wrong.
WARNING: vmlinux.o(.text+0x2d408): Section mismatch in reference from
the function _setup() to the function .init.text:_setup_postsetup()
The function _setup() references
the function __init _setup_postsetup().
This is often because _setup lacks a __init
annotation or the annotation of _setup_postsetup is wrong.
_setup is used in omap_hwmod_allocate_module, which isn't marked __init
and looks like it shouldn't be, meaning to fix these warnings, those
functions must be moved out of the init section, which this patch does.
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit fa68d4f847 ]
Some of the functions (like cdn_dp_dpcd_read, cdn_dp_get_edid_block)
allow to read 64KiB, but the cdn_dp_mailbox_read_receive, that is
used by them, can read only up to 255 bytes at once. Normally, it's
not a big issue as DPCD or EDID reads won't (hopefully) exceed that
value.
The real issue here is the revocation list read during the HDCP
authentication process. (problematic use case:
https://chromium.googlesource.com/chromiumos/third_party/kernel/+/chromeos-4.4/drivers/gpu/drm/rockchip/cdn-dp-reg.c#1152)
The list can reach 127*5+4 bytes (num devs * 5 bytes per ID/Bksv +
4 bytes of an additional info).
In other words - CTSes with HDCP Repeater won't pass without this
fix. Oh, and the driver will most likely stop working (best case
scenario).
Signed-off-by: Damian Kos <dkos@cadence.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Link: https://patchwork.freedesktop.org/patch/msgid/1541518625-25984-1-git-send-email-dkos@cadence.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 810eeb1f41 ]
The smsc95xx driver already takes into account the NET_IP_ALIGN
parameter when setting up the receive packet data, which means
we do not need to worry about aligning the packets in the usbnet
driver.
Adding the EVENT_NO_IP_ALIGN means that the IPv4 header is now
passed to the ip_rcv() routine with the start on an aligned address.
Tested on Raspberry Pi B3.
Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 336650c785 ]
The ad7780 driver previously did not read the correct device output, as
it read an outdated value set at initialization. It now updates its
voltage on read.
Signed-off-by: Renato Lui Geh <renatogeh@gmail.com>
Acked-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 15bc43f31a ]
Currently the time of SAS SSP connection is 1ms, which means the link
connection will fail if no IO response after this period.
For some disks handling large IO (such as 512k), 1ms is not enough, so
change it to 5ms.
Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d5585b7b68 ]
If a TX hang occurs, we attempt to recover by incrementally resetting.
If we're starved for CPU time, it's possible the reset doesn't actually
complete (or even fire) before another tx_timeout fires causing us to
fly through the different resets without actually doing them.
This adds a bit to set and check if a timeout recovery is already
pending and, if so, bail out of tx_timeout. The bit will get cleared at
the end of i40e_rebuild when reset is complete.
Signed-off-by: Alan Brady <alan.brady@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7cd8eb0861 ]
The i40e driver complains about unprivileged VFs trying to configure
promiscuous mode each time a VF reset occurs. This isn't the fault of
the poor VF driver - the PF driver itself is making the request.
To fix this, skip the privilege check if the request is to disable all
promiscuous activity. This gets rid of the bogus message, but doesn't
affect privilege checks, since we really only care if the unprivileged
VF is trying to enable promiscuous mode.
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6ad16b78a0 ]
EC_MKBP_EVENT_SENSOR_FIFO events can be triggered for a variety of
reasons, and there are very few cases in which they should be treated as
wakeup interrupts (particularly, when a certain
MOTIONSENSE_MODULE_FLAG_* is set, but this is not even supported in the
mainline cros_ec_sensor driver yet). Most of the time, they are benign
sensor readings. In any case, the top-level cros_ec device doesn't know
enough to determine that they should wake the system, and so it should
not report the event. This would be the job of the cros_ec_sensors
driver to parse.
This patch adds checks to cros_ec_get_next_event() such that it doesn't
signal 'wakeup' for events of type EC_MKBP_EVENT_SENSOR_FIFO.
This patch is particularly relevant on devices like Scarlet (Rockchip
RK3399 tablet, known as Acer Chromebook Tab 10), where the EC firmware
reports sensor events much more frequently. This was causing
/sys/power/wakeup_count to increase very frequently, often needlessly
interrupting our ability to suspend the system.
Signed-off-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Benson Leung <bleung@chromium.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b8ae30a702 ]
With the new CONFIG_CC_OPTIMIZE_FOR_DEBUGGING option, we get a link
error in the vboxguest driver, when that fails to optimize out the
call to the compat handler:
drivers/virt/vboxguest/vboxguest_core.o: In function `vbg_ioctl_hgcm_call':
vboxguest_core.c:(.text+0x1f6e): undefined reference to `vbg_hgcm_call32'
Another compile-time check documents better what we want and avoids
the error.
Acked-by: Randy Dunlap <rdunlap@infradead.org>
Tested-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 187fade88c ]
If mapping the CvP BAR fails, we still can configure the FPGA via
PCI config space access. In this case the iomap pointer is NULL.
On x86_64, passing NULL address to pci_iounmap() generates
"Bad IO access at port 0x0" output with stack call trace. Fix it.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Acked-by: Alan Tull <atull@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4fcba7802c ]
The patch fixes:
hv_kvp_daemon.c: In function 'kvp_set_ip_info':
hv_kvp_daemon.c:1305:2: note: 'snprintf' output between 41 and 4136 bytes
into a destination of size 4096
The "(unsigned int)str_len" is to avoid:
hv_kvp_daemon.c:1309:30: warning: comparison of integer expressions of
different signedness: 'int' and 'long unsigned int' [-Wsign-compare]
Signed-off-by: Dexuan Cui <decui@microsoft.com>
Cc: K. Y. Srinivasan <kys@microsoft.com>
Cc: Haiyang Zhang <haiyangz@microsoft.com>
Cc: Stephen Hemminger <sthemmin@microsoft.com>
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 68f60538da ]
The probe function needs to verify the CvP enable bit in order to
properly determine if FPGA Manager functionality can be safely
enabled.
Fixes: 34d1dc17ce ("fpga manager: Add Altera CvP driver")
Signed-off-by: Andreas Puhm <puhm@oregano.at>
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Reviewed-by: Moritz Fischer <mdf@kernel.org>
Acked-by: Alan Tull <atull@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b3a3eafeef ]
Previously, ad2s90_probe ignored the return code from spi_setup, not
handling its possible failure. This patch makes ad2s90_probe check if
the code is an error code and, if so, do the following:
- Call dev_err with an appropriate error message.
- Return the spi_setup's error code.
Note: The 'return ret' statement could be out of the 'if' block, but
this whole block will be moved up in the function in the patch:
'staging:iio:ad2s90: Move device registration to the end of probe'.
Signed-off-by: Matheus Tavares <matheus.bernardino@usp.br>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5c2dbebb44 ]
If the association supports HE, HT/VHT rates will never be used for Tx
and therefore there's no need to set the sgi-per-channel-width-support
bits, so don't set them in this case.
Fixes: 110b32f065 ("iwlwifi: mvm: rs: add basic implementation of the new RS API handlers")
Signed-off-by: Naftali Goldstein <naftali.goldstein@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5500598abb ]
The fsl_mc_portal_allocate can fail when the requested MC portals are
not yet probed by the fsl_mc_allocator. In this situation, the driver
should defer the probe.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5ec17af7ea ]
The Intel EG20T Platform Controller Hub used on the MIPS Boston
development board supports prefetching memory to optimize DMA transfers.
Unfortunately for unknown reasons this doesn't work well with some MIPS
CPUs such as the P6600, particularly when using an I/O Coherence Unit
(IOCU) to provide cache-coherent DMA. In these systems it is common for
DMA data to be lost, resulting in broken access to EG20T devices such as
the MMC or SATA controllers.
Support for a DT property to configure the prefetching was added a while
back by commit 549ce8f134 ("misc: pch_phub: Read prefetch value from
device tree if passed") but we never added the DT snippet to make use of
it. Add that now in order to disable the prefetching & fix DMA on the
affected systems.
Signed-off-by: Paul Burton <paul.burton@mips.com>
Patchwork: https://patchwork.linux-mips.org/patch/21068/
Cc: linux-mips@linux-mips.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 83d0bdc739 ]
If a gettime64 call fails, return the error and avoid copying data back
to user.
Cc: Richard Cochran <richardcochran@gmail.com>
Cc: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Miroslav Lichvar <mlichvar@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 397bd9211f ]
Current driver only enable parity enable bit and never clear it
when user set the termios. The fix clear the parity enable bit when
PARENB flag is not set in termios->c_cflag.
Cc: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Andy Duan <fugang.duan@nxp.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0560054da5 ]
For the YUV conversion to work properly, ->x_scaling[1] should never
be set to VC4_SCALING_NONE, but vc4_get_scaling_mode() might return
VC4_SCALING_NONE if the horizontal scaling ratio exactly matches the
horizontal subsampling factor. Add a test to turn VC4_SCALING_NONE
into VC4_SCALING_PPF when that happens.
The old ->x_scaling[0] adjustment is dropped as I couldn't find any
mention to this constraint in the spec and it's proven to be
unnecessary (I tested various multi-planar YUV formats with scaling
disabled, and all of them worked fine without this adjustment).
Fixes: fc04023faf ("drm/vc4: Add support for YUV planes.")
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Reviewed-by: Eric Anholt <eric@anholt.net>
Link: https://patchwork.freedesktop.org/patch/msgid/20181109102633.32603-1-boris.brezillon@bootlin.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0a6a40c2a8 ]
In the "aes-fixed-time" AES implementation, disable interrupts while
accessing the S-box, in order to make cache-timing attacks more
difficult. Previously it was possible for the CPU to be interrupted
while the S-box was loaded into L1 cache, potentially evicting the
cachelines and causing later table lookups to be time-variant.
In tests I did on x86 and ARM, this doesn't affect performance
significantly. Responsiveness is potentially a concern, but interrupts
are only disabled for a single AES block.
Note that even after this change, the implementation still isn't
necessarily guaranteed to be constant-time; see
https://cr.yp.to/antiforgery/cachetiming-20050414.pdf for a discussion
of the many difficulties involved in writing truly constant-time AES
software. But it's valuable to make such attacks more difficult.
Reviewed-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Eric Biggers <ebiggers@google.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b144b99fff ]
By default, READ MAC on a Layer2 OSD device returns the adapter's
burnt-in MAC address. Given the default scenario of many virtual devices
on the same adapter, qeth can't make any use of this address and
therefore skips the READ MAC call for this device type.
But in some configurations, the READ MAC command for a Layer2 OSD device
actually returns a pre-provisioned, virtual MAC address. So enable the
READ MAC code to detect this situation, and let the L2 subdriver
call READ MAC for OSD devices.
This also removes the QETH_LAYER2_MAC_READ flag, which protects L2
devices against calling READ MAC multiple times. Instead protect the
whole call to qeth_l2_request_initial_mac().
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit bf598a8f0f ]
bpftool output is not user friendly when dumping a map with only a few
populated entries:
$ bpftool map
1: devmap name tx_devmap flags 0x0
key 4B value 4B max_entries 64 memlock 4096B
2: array name tx_idxmap flags 0x0
key 4B value 4B max_entries 64 memlock 4096B
$ bpftool map dump id 1
key:
00 00 00 00
value:
No such file or directory
key:
01 00 00 00
value:
No such file or directory
key:
02 00 00 00
value:
No such file or directory
key: 03 00 00 00 value: 03 00 00 00
Handle ENOENT by keeping the line format sane and dumping
"<no entry>" for the value
$ bpftool map dump id 1
key: 00 00 00 00 value: <no entry>
key: 01 00 00 00 value: <no entry>
key: 02 00 00 00 value: <no entry>
key: 03 00 00 00 value: 03 00 00 00
...
Signed-off-by: David Ahern <dsahern@gmail.com>
Acked-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5b3f5c408d ]
The previous commit, "of: overlay: add missing of_node_get() in
__of_attach_node_sysfs" added a missing of_node_get() to
__of_attach_node_sysfs(). This results in a refcount imbalance
for nodes attached with dlpar_attach_node(). The calling sequence
from dlpar_attach_node() to __of_attach_node_sysfs() is:
dlpar_attach_node()
of_attach_node()
__of_attach_node_sysfs()
For more detailed description of the node refcount, see
commit 68baf692c4 ("powerpc/pseries: Fix of_node_put() underflow
during DLPAR remove").
Tested-by: Alan Tull <atull@kernel.org>
Acked-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Frank Rowand <frank.rowand@sony.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 53bb565fc5 ]
In the expression "word1 << 16", word1 starts as u16, but is promoted to a
signed int, then sign-extended to resource_size_t, which is probably not
what was intended. Cast to resource_size_t to avoid the sign extension.
This fixes an identical issue as fixed by commit 0b2d70764b ("x86/PCI:
Fix Broadcom CNB20LE unintended sign extension") back in 2014.
Detected by CoverityScan, CID#138749, 138750 ("Unintended sign extension")
Fixes: 3f6ea84a30 ("PCI: read memory ranges out of Broadcom CNB20LE host bridge")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Bjorn Helgaas <helgaas@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 216f0efd19 ]
Before this patch, recovery would cause all callbacks to be delayed,
put on a queue, and afterward they were all queued to the callback
work queue. This patch does the same thing, but occasionally takes
a break after 25 of them so it won't swamp the CPU at the expense
of other RT processes like corosync.
Signed-off-by: Bob Peterson <rpeterso@redhat.com>
Signed-off-by: David Teigland <teigland@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 46fda5b506 ]
Smatch report warnings:
drivers/clk/imgtec/clk-boston.c:76 clk_boston_setup() warn: possible memory leak of 'onecell'
drivers/clk/imgtec/clk-boston.c:83 clk_boston_setup() warn: possible memory leak of 'onecell'
drivers/clk/imgtec/clk-boston.c:90 clk_boston_setup() warn: possible memory leak of 'onecell'
'onecell' is malloced in clk_boston_setup(), but not be freed
before leaving from the error handling cases.
Signed-off-by: Yi Wang <wang.yi59@zte.com.cn>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 82c08c3e7f ]
In case panic() and panic() called at the same time on different CPUS.
For example:
CPU 0:
panic()
__crash_kexec
machine_crash_shutdown
crash_smp_send_stop
machine_kexec
BUG_ON(num_online_cpus() > 1);
CPU 1:
panic()
local_irq_disable
panic_smp_self_stop
If CPU 1 calls panic_smp_self_stop() before crash_smp_send_stop(), kdump
fails. CPU1 can't receive the ipi irq, CPU1 will be always online.
To fix this problem, this patch split out the panic_smp_self_stop()
and add set_cpu_online(smp_processor_id(), false).
Signed-off-by: Yufen Wang <wangyufen@huawei.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 30e196cace ]
After a LOGO in response to an ABTS timeout, a PLOGI wasn't issued to
re-establish the login. An nlp_type check in the LOGO completion
handler failed to restart discovery for NVME targets. Revised the
nlp_type check for NVME as well as SCSI.
While reviewing the LOGO handling a few other issues were seen and
were addressed:
- Better lock synchronization around ndlp data types
- When the ABTS times out, unregister the RPI before sending the LOGO
so that all local exchange contexts are cleared and nothing received
while awaiting LOGO/PLOGI handling will be accepted.
- LOGO handling optimized to:
Wait only R_A_TOV for a response.
It doesn't need to be retried on timeout. If there wasn't a
response, a PLOGI will be sent, thus an implicit logout
applies as well when the other port sees it.
If there is a response, any kind of response is considered "good"
and the XRI quarantined for a exchange qualifier window.
- PLOGI is issued as soon a LOGO state is resolved.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit dc730212e8 ]
Call sas_remove_host() before removing the target devices in the driver's
.remove() callback function(i.e. during driver unload time). So that
driver can provide a way to allow SYNC CACHE, START STOP unit commands
etc. (which are issued from SML) to the target drives during driver unload
time.
Once sas_remove_host() is called before removing the target drives then
driver can just clean up the resources allocated for target devices and no
need to call sas_port_delete_phy(), sas_port_delete() API's as these API's
internally called from sas_remove_host().
Signed-off-by: Suganath Prabu <suganath-prabu.subramani@broadcom.com>
Reviewed-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b114d9009d ]
When LCB's are rejected, if beaconing was already in progress, the
Reason Code Explanation was not being set. Should have been set to
command in progress.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3831a2a001 ]
In order to properly support dynack in ad-hoc mode running
wpa_supplicant, take into account authentication frames for
'late ack' detection. This patch has been tested on devices
mounted on offshore high-voltage stations connected through
~24Km link
Reported-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
Tested-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2bd345cd2b ]
Commit 2ea9f12cef ("ath10k: add new cipher suite support") added a new
n_cipher_suites HW param with a fallback value and a warning log. Commit
03a72288c5 ("ath10k: wmi: add hw params entry for wcn3990") later
added WCN3990 HW entries, but it missed the n_cipher_suites.
Rather than seeing this warning every boot
ath10k_snoc 18800000.wifi: invalid hw_params.n_cipher_suites 0
let's provide the appropriate value.
Cc: Rakesh Pillai <pillair@qti.qualcomm.com>
Cc: Govind Singh <govinds@qti.qualcomm.com>
Signed-off-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
