Add support for dynamically discovering and exposing Configuration
Security Unit (CSU) registers through sysfs. Leverage the existing
PM_QUERY_DATA API to discover available registers at runtime, making
the interface flexible and maintainable.
Key features:
- Dynamic register discovery using PM_QUERY_DATA API
* PM_QID_GET_NODE_COUNT: Query number of available registers
* PM_QID_GET_NODE_NAME: Query register names by index
- Automatic sysfs attribute creation under csu_registers/ group
- Read operations via existing IOCTL_READ_REG API
- Write operations via existing IOCTL_MASK_WRITE_REG API
The sysfs interface is created at:
/sys/devices/platform/firmware:zynqmp-firmware/csu_registers/
Currently supported registers include:
- multiboot (CSU_MULTI_BOOT)
- idcode (CSU_IDCODE, read-only)
- pcap-status (CSU_PCAP_STATUS, read-only)
The dynamic discovery approach allows firmware to control which
registers are exposed without requiring kernel changes, improving
maintainability and security.
The firmware does not currently expose per-register access mode
information, so the kernel cannot distinguish read-only registers
from read-write ones at discovery time. All discovered registers are
therefore created with sysfs mode 0644, and the firmware is
responsible for rejecting writes to registers it treats as read-only
(for example idcode and pcap-status); that error is propagated back
to userspace from the store callback. If a per-register access-mode
query is added to the firmware in the future, sysfs permissions can
be tightened to match.
CSU register discovery is an optional feature: on firmware that lacks
support for PM_QID_GET_NODE_COUNT or PM_QID_GET_NODE_NAME, the probe
returns gracefully without exposing any sysfs entries. To keep the
memory footprint minimal on that path, partial devm allocations made
during discovery are explicitly released on failure so that no memory
lingers until device unbind when the feature is unavailable.
Signed-off-by: Ronak Jain <ronak.jain@amd.com>
Signed-off-by: Michal Simek <michal.simek@amd.com>
Link: https://lore.kernel.org/r/20260520093654.3303917-3-ronak.jain@amd.com
Document the new sysfs interface that exposes Configuration Security
Unit (CSU) registers through the zynqmp-firmware driver.
The interface is available under:
/sys/devices/platform/firmware:zynqmp-firmware/csu_registers/
The CSU registers are discovered at boot time using the PM_QUERY_DATA
firmware API. The following registers are currently supported:
- multiboot (CSU_MULTI_BOOT)
- idcode (CSU_IDCODE, read-only)
- pcap-status (CSU_PCAP_STATUS, read-only)
Read operations use the existing IOCTL_READ_REG firmware interface,
while write operations use IOCTL_MASK_WRITE_REG.
Access control is enforced by the firmware. Write attempts to
read-only registers are rejected by firmware even though the sysfs file
permissions allow writes.
Document the ABI entry accordingly.
Signed-off-by: Ronak Jain <ronak.jain@amd.com>
Signed-off-by: Michal Simek <michal.simek@amd.com>
Link: https://lore.kernel.org/r/20260520093654.3303917-2-ronak.jain@amd.com
The irdma_copy_user_pgaddrs function loops through all of the umem DMA
blocks to populate the PBLEs and will stop when either the last DMA
block is reached or palloc->total_cnt is reached. The issue is that
the logic for checking palloc->total_cnt would only work for non-zero
values.
When irdma_setup_pbles is called with lvl==0, it
calls irdma_copy_user_pgaddrs with palloc->total_cnt==0, which means
the only way to break out of the loop is to reach the last umem DMA
block, which means it could end up going beyond the fixed size of 4
iwmr->pgaddrmem array that is used in the lvl==0 case.
In the case of QP/CQ/SRQ rings, the value of lvl is determined by a
separate input (for example, req.cq_pages in the case of a CQ). So,
we must perform explicit checking to ensure we don't overflow the
pgaddrmem array if the user provides a umem that consists of more
blocks than their provided req.cq_pages.
Fixes: b48c24c2d7 ("RDMA/irdma: Implement device supported verb APIs")
Link: https://patch.msgid.link/r/20260512183852.614045-1-jmoroni@google.com
Signed-off-by: Jacob Moroni <jmoroni@google.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
Srinivas Kandagatla <srinivas.kandagatla@oss.qualcomm.com> says:
Here is the set of patches, that fixes one of the isssue reported by
Richard Acayan, while doing fix for the reported issue, found various
other issues in the existing code.
This set contains some of those cleanups along with few trivial coding
style patches which looked uncomfortable to read.
Patch 1 should be enough to fix the issue reported.
Tested this is on UNO-Q.
Link: https://patch.msgid.link/20260518092347.3446946-1-srinivas.kandagatla@oss.qualcomm.com
The ASM_CLIENT_EVENT_DATA_WRITE_DONE case does not declare any local
variables or require a separate scope, so drop the unnecessary braces.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@oss.qualcomm.com>
Link: https://patch.msgid.link/20260518092347.3446946-5-srinivas.kandagatla@oss.qualcomm.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Fix error handling in q6asm_dai_compr_set_params() and q6asm_dai_prepare()
for both CMD_CLOSE and q6asm_unmap_memory_regions().
In both the functions, we are doing q6asm_audio_client_free in failure
cases, which means if prepare or set_params fail, we can never recover.
Now open and close are done in respective dai_open/close functions.
Fixes: 2a9e92d371 ("ASoC: qdsp6: q6asm: Add q6asm dai driver")
Cc: Stable@vger.kernel.org
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@oss.qualcomm.com>
Link: https://patch.msgid.link/20260518092347.3446946-4-srinivas.kandagatla@oss.qualcomm.com
Signed-off-by: Mark Brown <broonie@kernel.org>
q6asm_dai_close() and q6asm_dai_compr_free() currently issue CMD_CLOSE
whenever prtd->state is non-zero.
After prepare() closes an existing stream, the state is updated to
Q6ASM_STREAM_STOPPED. Since this state is also non-zero, the close and
free paths can send CMD_CLOSE again for a stream that has already been
closed.
Restrict CMD_CLOSE to the Q6ASM_STREAM_RUNNING state so the command is
sent only when the ASM stream is still active.
Fixes: 2a9e92d371 ("ASoC: qdsp6: q6asm: Add q6asm dai driver")
Cc: Stable@vger.kernel.org
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@oss.qualcomm.com>
Link: https://patch.msgid.link/20260518092347.3446946-3-srinivas.kandagatla@oss.qualcomm.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The q6asm-dai stream state is used by prepare() to decide whether an
existing stream setup needs to be closed before opening/configuring a new
one. Updating the state from trigger or asynchronous DSP callbacks can make
that state stale or incorrect relative to the actual setup lifetime.
In particular, setting Q6ASM_STREAM_STOPPED on STOP or EOS completion can
make prepare() believe there is no active setup to close, which can result
in opening/configuring the same stream more than once.
Keep stream state updates tied to prepare(), where the stream is actually
closed and reopened, and stop changing it from trigger and EOS callbacks.
Fixes: bfbb12dfa1 ("ASoC: qcom: q6asm-dai: perform correct state check before closing")
Cc: Stable@vger.kernel.org
Closes: https://lore.kernel.org/all/afS7rTHdc9TyIeLx@rdacayan/
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@oss.qualcomm.com>
Link: https://patch.msgid.link/20260518092347.3446946-2-srinivas.kandagatla@oss.qualcomm.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Srinivas Kandagatla <srinivas.kandagatla@oss.qualcomm.com> says:
The MAX98090 codec driver currently exposes a custom
max98090_mic_detect() helper for machine drivers to register a headset
jack.
This series converts the driver to use the standard component
.set_jack callback and updates the mt8173-max98090 machine driver to use
snd_soc_component_set_jack() instead of the codec-specific helper.
Using the standard callback removes the need for a custom exported
symbol and allows machine drivers to use the common ASoC jack
registration interface. This also improves compatibility with machine
drivers, such as Qualcomm platforms, that already rely on
snd_soc_component_set_jack().
Link: https://patch.msgid.link/20260520155002.145306-1-srinivas.kandagatla@oss.qualcomm.com
The MAX98090 driver provides a custom max98090_mic_detect() helper for
machine drivers to register a jack.
This can be implemented using the standard component set_jack callback
instead. Doing so allows machine drivers to use
snd_soc_component_set_jack(), which is also the interface used by
machine drivers including Qualcomm ones.
Convert max98090_mic_detect() to a component set_jack callback and remove
the exported helper.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@oss.qualcomm.com>
Link: https://patch.msgid.link/20260520155002.145306-3-srinivas.kandagatla@oss.qualcomm.com
Signed-off-by: Mark Brown <broonie@kernel.org>
use snd_soc_component_set_jack() instead of custom callback to
max98090 codec.
This will help other drivers using the standard callback to exercise
the standard path instead of custom callback.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@oss.qualcomm.com>
Link: https://patch.msgid.link/20260520155002.145306-2-srinivas.kandagatla@oss.qualcomm.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Chancel Liu <chancel.liu@nxp.com> says:
Some audio systems require specific DAPM widgets to remain powered
during system suspend. Introduce a generic and reusable mechanism in
the ASoC core to mark selected DAPM widgets as ignore_suspend.
The unified mechanism consists of two parts:
1. Parse and store the name list of widgets to ignore suspend in
struct snd_soc_card
The list of widgets can be provided either by the machine driver or
parsed from Device Tree. Different machines have different routing and
power requirements. Each machine can specify its own widgets to ignore
suspend through DT property. It enables flexible policy without hard
code. A new helper, snd_soc_of_parse_ignore_suspend_widgets() is added
for this purpose.
2. Apply ignore_suspend flags during snd_soc_bind_card()
After all components have been probed and all DAPM widgets have been
registered, snd_soc_bind_card() performs a unified lookup of the
configured widget names across all DAPM contexts of the card and marks
the matching widgets with ignore_suspend = 1.
Switch to use core ignore-suspend-widgets support for imx-rpmsg driver.
Chancel Liu (3):
ASoC: dapm: Fix widget lookup with prefixed names across DAPM contexts
ASoC: soc-core: Add core support for ignoring suspend on selected DAPM
widgets
ASoC: fsl: imx-rpmsg: Switch to core ignore-suspend-widgets support
Link: https://patch.msgid.link/20260507013654.2945915-1-chancel.liu@nxp.com
The imx-rpmsg machine driver currently implements its own logic to
parse ignore-suspend-widgets from Device Tree and manually traverse
DAPM widgets to mark them as ignore_suspend.
It also has a potential issue that some widgets listed in the property
(e.g. "Headphone Jack") belong to card or CPU DAI DAPM context.
Switch to use snd_soc_of_parse_ignore_suspend_widgets() with the
introduction of a generic ignore-suspend-widgets mechanism in the ASoC
core.
Signed-off-by: Chancel Liu <chancel.liu@nxp.com>
Link: https://patch.msgid.link/20260507013654.2945915-4-chancel.liu@nxp.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Some audio systems require specific DAPM widgets to remain powered
during system suspend. Introduce a generic and reusable mechanism in
the ASoC core to mark selected DAPM widgets as ignore_suspend.
The unified mechanism consists of two parts:
1. Parse and store the name list of widgets to ignore suspend in
struct snd_soc_card
The list of widgets can be provided either by the machine driver or
parsed from Device Tree. Different machines have different routing and
power requirements. Each machine can specify its own widgets to ignore
suspend through DT property. It enables flexible policy without hard
code. A new helper, snd_soc_of_parse_ignore_suspend_widgets() is added
for this purpose.
2. Apply ignore_suspend flags during snd_soc_bind_card()
After all components have been probed and all DAPM widgets have been
registered, snd_soc_bind_card() performs a unified lookup of the
configured widget names across all DAPM contexts of the card and marks
the matching widgets with ignore_suspend = 1.
Signed-off-by: Chancel Liu <chancel.liu@nxp.com>
Link: https://patch.msgid.link/20260507013654.2945915-3-chancel.liu@nxp.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Currently dapm_find_widget() manually constructs a prefixed widget name
based on the provided DAPM context and compares it using strcmp(). This
happens to work in most cases because callers usually know which DAPM
context the target widget belongs to and pass in the matching DAPM
context.
However, this assumption breaks when search_other_contexts is enabled.
In such cases, callers may intentionally pass a different DAPM context,
while searching for a widget that actually belongs to another DAPM
context.
For example, when searching for a "DAC" widget, the widget belongs to
the codec DAPM and be registered with a codec prefix, while the caller
passes card->dapm and intends to search across all DAPM contexts. The
current implementation incorrectly applies the caller card DAPM causing
the lookup to fail even though the widget exists on the card.
Improve the matching strategy to support both use cases:
1. When the caller provides a fully qualified name with prefix, perform
exact string matching. This preserves the ability to use prefixes for
disambiguation.
2. When the caller provides a bare widget name without prefix, try exact
matching first, then fall back to prefix-stripped comparison using
snd_soc_dapm_widget_name_cmp().
To determine whether the pin name includes a prefix, a new helper
function snd_soc_dapm_pin_has_prefix() is introduced. It checks if the
pin name starts with any known component prefix on the card.
This fixes widget lookup failures when searching across different DAPM
contexts while maintaining backward compatibility for explicitly
prefixed lookups.
Fixes: ae4fc53224 ("ASoC: dapm: use component prefix when checking widget names")
Signed-off-by: Chancel Liu <chancel.liu@nxp.com>
Assisted-by: Cody:Claude-4.5-Sonnet
Link: https://patch.msgid.link/20260507013654.2945915-2-chancel.liu@nxp.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Use of_device_get_match_data() to fetch platform match data directly
instead of open-coding an of_match_device() lookup.
This also lets the driver drop the of_device.h include.
Assisted-by: Codex:GPT-5.5
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://patch.msgid.link/20260519004352.627148-1-rosenp@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
byt_cht_es8316_init() enables MCLK before configuring the codec sysclk
and creating the headset jack. If either of those later steps fails, the
function returns without disabling MCLK, leaving the clock enabled after
card registration fails.
Track whether this driver enabled MCLK and disable it on the init error
paths. Add the matching DAI link exit callback so the same clock enable
is also balanced when ASoC cleans up a successfully initialized link.
Fixes: a03bdaa565 ("ASoC: Intel: add machine driver for BYT/CHT + ES8316")
Signed-off-by: Cássio Gabriel <cassiogabrielcontato@gmail.com>
Link: https://patch.msgid.link/20260519-asoc-bytcht-es8316-mclk-leak-v1-1-b4a11cdc2afd@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Detect DPRX capability changes without a long HPD or RX_CAP_CHANGED
signal and queue a corresponding link params reset.
Besides detecting the above unexpected capability changes, this also
avoids races between queuing and handling a deferred link params reset.
v2: (Ville)
- Query/set intel_dp::reset_link_params instead of using helpers for
these.
- Assert matching types for old/new common rate elements as well.
- Add TODO: for adding a struct tracking both rates and number of rates.
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patch.msgid.link/20260522160514.2628249-5-imre.deak@intel.com
Cache the maximum common lane count together with the common link
rates.
This is safe because the cached value is updated:
- during driver probe, before the connector is registered and can be
used for mode validation or modesetting
- during resume, before output HW state readout can query it
- during connector detection, right after updating the sink/link
capabilities
Caching the value allows detecting max common lane count changes in
a follow-up change and keeps the tracking of max common lane count
aligned with that of common rates.
Reviewed-by: Jouni Högander <jouni.hogander@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patch.msgid.link/20260522160514.2628249-4-imre.deak@intel.com
Add intel_dp_set_common_link_params() to prepare for updating the
maximum common lane count together with the common rates.
Reviewed-by: Jouni Högander <jouni.hogander@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patch.msgid.link/20260522160514.2628249-3-imre.deak@intel.com
There is no reason to distinguish between DPRX capability changes
signaled via a long HPD and via an RX_CAP_CHANGED HPD IRQ.
Both cases result in reading out the DPRX capabilities and updating the
corresponding sink and common capabilities cached in intel_dp, however
only the long HPD resets the link training/recovery state and MST link
probe parameters correspondingly. The link training/recovery state may
contain reduced maximum link rate/lane count values left over from a
previous link training failure.
Based on the above after an RX_CAP_CHANGED increased the link rate, lane
count parameters the maximum link rate/lane count in the link
training/recovery state may remain below these, leaving the newly added
valid configurations unavailable for subsequent modesets in an
inconsistent way.
Handle RX_CAP_CHANGED IRQs the same way as long HPDs and reset the link
recovery state and MST link probe parameters in that case as well.
v2: Set intel_dp::reset_link_params instead of using a helper for this.
(Ville).
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patch.msgid.link/20260522160514.2628249-2-imre.deak@intel.com
- Drop CONFIG_MPLS_IPTUNNEL=m (depends on LWTUNNEL, which is no longer
auto-enabled since since commit 309b905dee ("ipv6: convert
CONFIG_IPV6 to built-in only and clean up Kconfigs")),
- Drop CONFIG_HID_ITE=n and CONFIG_HID_REDRAGON=n (disabled by default
since commit 3d39be2a76 ("HID: drop 'default !EXPERT' from
tristate symbols")),
- Enable modular build of the CMAC, MD5, SHA-512, and SHA-3 algorithms
(no longer auto-enabled since commits 4c1c07820a ("smb:
client: Remove obsolete cmac(aes) allocation"), 7aa0f56d4b
("scsi: iscsi_tcp: Remove unneeded selections of CRYPTO and
CRYPTO_MD5"), commit 4061bc8c03 ("crypto: rng - Don't pull in
DRBG when CRYPTO_FIPS=n"), resp. ce260754bb ("crypto:
jitterentropy - Use SHA-3 library")),
- Drop CONFIG_CRYPTO_DRBG_HASH=y and CONFIG_CRYPTO_DRBG_CTR=y (depend
on CRYPTO_DRBG_MENU, which is no longer auto-enabled since commit
4061bc8c03 ("crypto: rng - Don't pull in DRBG when
CRYPTO_FIPS=n")),
- Enable modular build of all CRC functions and crypto library code
for KUnit tests,
- Enable benchmarking in the (modular) string functions KUnit test,
- Enable modular build of the new test module for stress/performance
analysis of workqueue.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Link: https://patch.msgid.link/d20ee047f2133570673e108d1ffb0c6400a2e240.1777290987.git.geert@linux-m68k.org
hyperv_receive_sub() reads msg->vid_hdr.type and dispatches into one
of four message-type branches without knowing how many bytes the host
wrote into hv->recv_buf. The completion path then runs
memcpy(hv->init_buf, msg, VMBUS_MAX_PACKET_SIZE), so the consumer that
wakes on wait_for_completion_timeout() can read up to 16 KiB of
residue from a prior message as if it were the response payload.
Pass bytes_recvd into hyperv_receive_sub() and reject any packet that
does not cover the pipe + synthvid header. A single switch on
msg->vid_hdr.type then computes the type-specific payload size: the
three completion-driving types (SYNTHVID_VERSION_RESPONSE,
SYNTHVID_RESOLUTION_RESPONSE, SYNTHVID_VRAM_LOCATION_ACK) fall through
to a shared exit that requires that size before memcpy/complete, while
SYNTHVID_FEATURE_CHANGE validates its own payload and returns before
reading is_dirt_needed. Unknown types are dropped.
SYNTHVID_RESOLUTION_RESPONSE is variable length: the host fills
resolution_count entries, not the full SYNTHVID_MAX_RESOLUTION_COUNT
array. Validate the fixed prefix first so resolution_count can be
read, bound it against the array, then require only the count-sized
array, so the shorter responses the host actually sends are accepted.
Only run the sub-handler when vmbus_recvpacket() returned success. The
memcpy length is bytes_recvd, which is bounded by VMBUS_MAX_PACKET_SIZE
only on a successful receive; on -ENOBUFS vmbus_recvpacket() instead
reports the required length, which can exceed hv->recv_buf, so copying
bytes_recvd would read and write past the 16 KiB buffers. Gating on the
success return keeps the copy bounded. The nonzero-return path is itself
a malformed-message case and is now logged rather than silently skipped;
channel recovery is not attempted.
Rejected packets are reported via drm_err_ratelimited() rather than
silently dropped, matching the CoCo-hardened pattern in
hv_kvp_onchannelcallback().
Fixes: 76c56a5aff ("drm/hyperv: Add DRM driver for hyperv synthetic video device")
Cc: stable@vger.kernel.org # 5.14+
Signed-off-by: Berkant Koc <me@berkoc.com>
Assisted-by: Claude:claude-opus-4-7 berkoc-pipeline
Reviewed-by: Michael Kelley <mhklinux@outlook.com>
Tested-by: Michael Kelley <mhklinux@outlook.com>
Signed-off-by: Hamza Mahfooz <hamzamahfooz@linux.microsoft.com>
Link: https://patch.msgid.link/8200dbc199c7a9b75ac7e8af6c748d2189b5ebd5.1779542874.git.me@berkoc.com
A SYNTHVID_RESOLUTION_RESPONSE with resolution_count > 64 walks past
the supported_resolution[SYNTHVID_MAX_RESOLUTION_COUNT] array in the
parse loop. Bound resolution_count against the array size, folded
into the existing zero-check.
When the WIN10 resolution probe fails, the caller in
hyperv_connect_vsp() left hv->screen_*_max / preferred_* unpopulated,
which sets mode_config.max_width / max_height to 0 and makes
drm_internal_framebuffer_create() reject every userspace framebuffer
with -EINVAL. The pre-WIN10 branch had the same gap for
preferred_width / preferred_height. Use a single post-probe fallback
guarded by screen_width_max == 0 so both paths converge on the WIN8
defaults.
Signed-off-by: Berkant Koc <me@berkoc.com>
Assisted-by: Claude:claude-opus-4-7 berkoc-pipeline
Fixes: 76c56a5aff ("drm/hyperv: Add DRM driver for hyperv synthetic video device")
Cc: stable@vger.kernel.org # 5.14+
Reviewed-by: Michael Kelley <mhklinux@outlook.com>
Tested-by: Michael Kelley <mhklinux@outlook.com>
Signed-off-by: Hamza Mahfooz <hamzamahfooz@linux.microsoft.com>
Link: https://patch.msgid.link/6945b22419c7d404b4954a113de2ac9c900dba93.1779542874.git.me@berkoc.com
Troy Mitchell <troy.mitchell@linux.spacemit.com> says:
On some SoCs (e.g. SpacemiT K3), multiple I2S controllers share the
same physical BCLK. When one controller is already streaming, the
others must use hw_params that result in the same BCLK rate, otherwise
the shared clock would be reconfigured and corrupt the active stream.
This series adds framework-level support for this constraint:
Patch 1 adds the dt-bindings for the spacemit,k3-i2s compatible.
The K3 SoC uses the same I2S IP as K1 but requires additional clocks:
a dedicated sysclk_div, along with c_sysclk and c_bclk which are
shared across multiple I2S controllers.
Patch 2 adds a DEFINE_GUARD wrapping snd_soc_card_mutex_lock() and
snd_soc_card_mutex_unlock() so that scope-based locking picks up the
SND_SOC_CARD_CLASS_RUNTIME lockdep subclass.
Patch 3 adds the constraint logic in soc-pcm.c. During PCM open,
every DAI that has a bclk clock pointer gets a hw_rule registered
unconditionally. The rule callback runs at hw_refine time: it scans
the card for an active peer sharing the same physical BCLK (via
clk_is_match()) that has already completed hw_params, then constrains
the current stream's rate to match the established BCLK rate. The
first DAI to complete hw_params is unconstrained; subsequent DAIs
must match. Two modes are supported:
- Default (I2S): BCLK = rate * channels * sample_bits. The rule
derives the valid rate range from the current channel and
sample_bits intervals.
- Explicit ratio (TDM): if the driver sets dai->bclk_ratio
(e.g. slots * slot_width), the rule computes the single valid
rate as active_bclk_rate / bclk_ratio.
This series was prompted by review feedback on the SpacemiT K3 I2S
series, where a vendor-specific fixed-sample-rate property was rejected
in favor of a generic framework solution:
https://lore.kernel.org/all/afFqgF6ZRwYdfUmL@sirena.co.uk/
Link: https://patch.msgid.link/20260522-i2s-same-blk-v4-0-a71a86faaa20@linux.spacemit.com
When multiple CPU DAIs on the same sound card share the same physical
BCLK, add a hw_rule during PCM open that constrains the sample rate so
the resulting BCLK rate stays consistent across all sharing DAIs.
The rule callback scans all DAIs on the card at hw_refine time, looking
for an active peer that shares the same physical BCLK (via
clk_is_match()) and has already completed hw_params (checked via
dai->symmetric_rate != 0). This ensures the constraint uses the real
BCLK rate established by the peer's clk_set_rate() in hw_params, not a
stale boot-time default.
The first DAI to complete hw_params is unconstrained (no active peer
yet); subsequent DAIs are constrained to match.
The rule supports two modes:
- If the DAI has an explicit bclk_ratio set (e.g. for TDM where
BCLK = rate * slots * slot_width), the rate is constrained to
active_bclk_rate / bclk_ratio.
- Otherwise, the default formula BCLK = rate * channels * sample_bits
is used to derive the valid rate range.
The constraint is purely additive: DAIs that do not set a bclk clock
pointer are completely unaffected.
Signed-off-by: Troy Mitchell <troy.mitchell@linux.spacemit.com>
Link: https://patch.msgid.link/20260522-i2s-same-blk-v4-3-a71a86faaa20@linux.spacemit.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Define a guard class wrapping snd_soc_card_mutex_lock() and
snd_soc_card_mutex_unlock() so that scope-based locking can be used
while still picking up the SND_SOC_CARD_CLASS_RUNTIME lockdep subclass.
Signed-off-by: Troy Mitchell <troy.mitchell@linux.spacemit.com>
Link: https://patch.msgid.link/20260522-i2s-same-blk-v4-2-a71a86faaa20@linux.spacemit.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Add a bclk field to struct snd_soc_dai and a helper function
snd_soc_dai_set_bclk_clk() that platform drivers can use to declare
which clock is their BCLK.
Also cache the bclk_ratio in snd_soc_dai_set_bclk_ratio() so that
the framework can use it later in hw_rule evaluation for TDM
configurations where BCLK = rate * slots * slot_width.
When multiple DAIs on the same card share the same physical BCLK
(detected via clk_is_match()), the ASoC core can automatically
constrain their hw_params so that the resulting BCLK rates are
compatible. This commit adds the data structure support; the actual
constraint logic follows in the next patch.
Signed-off-by: Troy Mitchell <troy.mitchell@linux.spacemit.com>
Link: https://patch.msgid.link/20260522-i2s-same-blk-v4-1-a71a86faaa20@linux.spacemit.com
Signed-off-by: Mark Brown <broonie@kernel.org>
For Legacy timing generator, if there are no panel replay/sel_update or
other SRD constraints, the Set context latency (SCL) window should be
at least 1.
However, for VRR timing generator the SCL window can be 0. It has other
guardband constraints, but that are checked during guardband computation.
Allow SCL to be 0 for platforms that have VRR TG always on.
Signed-off-by: Ankit Nautiyal <ankit.k.nautiyal@intel.com>
Reviewed-by: Suraj Kandpal <suraj.kandpal@intel.com>
Reviewed-by: Jouni Högander <jouni.hogander@intel.com>
Link: https://patch.msgid.link/20260517142753.2813959-3-ankit.k.nautiyal@intel.com
'needs_sel_update' is common for both display version branches, so check it
once and keep the version specific checks as separate early returns.
v2: Split into separate early returns. (Jani)
Signed-off-by: Ankit Nautiyal <ankit.k.nautiyal@intel.com>
Reviewed-by: Suraj Kandpal <suraj.kandpal@intel.com>
Reviewed-by: Jouni Högander <jouni.hogander@intel.com>
Link: https://patch.msgid.link/20260517142753.2813959-2-ankit.k.nautiyal@intel.com
Add support for identifying the R-Car M3Le (R8A779MD) SoC.
The Renesas R-Car R8A779MD M3Le SoC is a variant of the already
supported R-Car M3-N SoC with reduced peripherals.
Enable support for the M3Le SoC through already existing ARCH_R8A77965
configuration symbol. PRR reads 0x67c05501.
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Link: https://patch.msgid.link/20260504144534.43745-6-marek.vasut+renesas@mailbox.org
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Since Lunarlake there is no restriction planar planes has to be even
positions. Due to this we may end up having odd offset for UV-plane in
selective fetch configuration. Add handling for this case into selective
fetch configuration.
Bspec: 68927
Suggested-by: Vidya Srinivas <vidya.srinivas@intel.com>
Signed-off-by: Jouni Högander <jouni.hogander@intel.com>
Reviewed-by: Vidya Srinivas <vidya.srinivas@intel.com>
Link: https://patch.msgid.link/20260512080022.2527094-1-jouni.hogander@intel.com
We are observing following warnings:
*ERROR* power well DC_off state mismatch (refcount 0/enabled 1)
gen9_dc_off_power_well_enabled is considering target state DC_STATE_DISABLE
as DC_OFF power well being enabled. Fix this by using wakeref for the
purpose.
To achieve this we need to modify notification code as well. Currently it
is possible that PSR gets notified vblank enable/disable twice on same
status. This is currently not a problem as it is just triggering call to
intel_display_power_set_target_dc_state with same target state as a
parameter. When using wakeref this becomes a problem due to reference
counting. Fix this storing vbank status on last notification and use that
to ensure there are no more than one notification with same vblank status.
v2: ensure there is no subsequent notifications with same status
Fixes: aa451abcff ("drm/i915/display: Prevent DC6 while vblank is enabled for Panel Replay")
Cc: <stable@vger.kernel.org> # v6.13+
Signed-off-by: Jouni Högander <jouni.hogander@intel.com>
Reviewed-by: Michał Grzelak <michal.grzelak@intel.com>
Link: https://patch.msgid.link/20260520104944.239797-2-jouni.hogander@intel.com
Currently we are blocking DC states only when Panel Replay is enabled on
vblank enable. It may happen that Panel Replay is getting enabled when
vblank is already enabled. Fix this by blocking DC states always if Panel
Replay is supported.
While at it take care of possible dual eDP case by looping all encoders
supporting PSR.
Fixes: 0c427ac78a ("drm/i915/psr: Add interface to notify PSR of vblank enable/disable")
Cc: <stable@vger.kernel.org> # v6.16+
Signed-off-by: Jouni Högander <jouni.hogander@intel.com>
Reviewed-by: Michał Grzelak <michal.grzelak@intel.com>
Link: https://patch.msgid.link/20260520104944.239797-1-jouni.hogander@intel.com
The pinctrl and GPIO core code make exceptions for the -ENOTSUPP error
code. One such example is gpio_set_config_with_argument_optional(),
which returns success when gpio_set_config_with_argument() returns
-ENOTSUPP, but reports failure for all other error codes.
Returning -EOPNOTSUPP from the pinctrl driver on the unsupported pinctrl
operation may lead to boot failures when pinctrl drivers implements
struct gpio_chip::set_config, the system uses GPIO hogs, and the
struct gpio_chip::set_config implementation returns -EOPNOTSUPP for the
unsupported operations.
Return -ENOTSUPP for the unsupported pinctrl operation.
Fixes: 560c633d37 ("pinctrl: renesas: rzg2l: Drop oen_read and oen_write callbacks")
Fixes: c4c4637eb5 ("pinctrl: renesas: Add RZ/G2L pin and gpio controller driver")
Cc: stable@vger.kernel.org
Signed-off-by: Claudiu Beznea <claudiu.beznea.uj@bp.renesas.com>
Reviewed-by: Bartosz Golaszewski <bartosz.golaszewski@oss.qualcomm.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Tested-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://patch.msgid.link/20260515124008.2947838-2-claudiu.beznea@kernel.org
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
In rzt2h_pinctrl_set_pfc_mode(), read the PMC and PFC registers upfront
and skip the pin function configuration if the pin is already in
peripheral mode with the desired function.
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://patch.msgid.link/20260513115312.1574367-3-prabhakar.mahadev-lad.rj@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Variable 'j' in rzt2h_pinctrl_register() is incremented during pin
descriptor initialization but never used afterwards.
Remove the unused variable and the associated dead code.
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://patch.msgid.link/20260513115312.1574367-2-prabhakar.mahadev-lad.rj@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Rename the internal loop iterator variable in the for_each_mod_clock()
macro from 'i' to '__i'.
The current naming conflicts with local loop variables named 'i' inside
code blocks that utilize the macro, triggering compiler warnings due to
variable shadowing:
drivers/clk/renesas/rzg2l-cpg.c:1494:36: warning: declaration of `i` shadows a previous local [-Wshadow]
1494 | for (unsigned int i = 0; i < clk->num_shared_mstop_clks; i++)
Using a unique identifier for the macro-internal iterator resolves the
shadowing warnings globally across all macro expansions.
Fixes: 3fd4a8bb4b ("clk: renesas: rzg2l: Add macro to loop through module clocks")
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://patch.msgid.link/20260520092947.70596-1-prabhakar.mahadev-lad.rj@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
spacemit_pin_set_config() looks up the per-pin descriptor with
spacemit_get_pin() then checks the wrong variable for failure:
const struct spacemit_pin *spin = spacemit_get_pin(pctrl, pin);
...
if (!pin)
return -EINVAL;
reg = spacemit_pin_to_reg(pctrl, spin->pin);
pin is an unsigned int pin id, where 0 (GPIO_0 / gmac0_rxdv on K3) is a
valid pin, so rejecting it here drops the PAD config write for the first
pin of every group. On K3 Pico-ITX the GMAC RGMII group lists pin 0 as
its first entry, so its drive-strength / bias configuration was silently
ignored.
The intended guard is against spacemit_get_pin() returning NULL when the
pin id isn't in the SoC's pin table. Check spin instead, which both
restores PAD setup for pin 0 and prevents a NULL deref on spin->pin.
Fixes: a83c29e1d1 ("pinctrl: spacemit: add support for SpacemiT K1 SoC")
Signed-off-by: Han Gao <gaohan@iscas.ac.cn>
Reviewed-by: Troy Mitchell <troy.mitchell@linux.spacemit.com>
Reviewed-by: Yixun Lan <dlan@kernel.org>
Signed-off-by: Linus Walleij <linusw@kernel.org>
Drivers were accessing this drm_exec member directly.
While that may seem harmless, it will require action if
the drm_exec utility is made a subclass of a dma-resv transaction
utility as outlined in the cover-letter.
Provide an accessor, drm_exec_ticket() to avoid that.
v2:
- Fix amdgpu compile error (Intel CI)
- Update the commit message.
Signed-off-by: Thomas Hellström <thomas.hellstrom@linux.intel.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Link: https://patch.msgid.link/20260520101616.41284-5-thomas.hellstrom@linux.intel.com
The xe driver was using the drm_exec retry pointer directly to
restart the locking loop after out-of-memory errors. This is
relying on undocumented behaviour.
Instead add a drm_exec_retry() macro that can be used in this
situation, and that also warns if the struct drm_exec is
not newly (re-)initialized.
Use that macro in xe.
v2:
- Only allow if the drm_exec context is newly initialized.
(Christian)
Signed-off-by: Thomas Hellström <thomas.hellstrom@linux.intel.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Link: https://patch.msgid.link/20260520101616.41284-4-thomas.hellstrom@linux.intel.com
Use __UNIQUE_ID as done elsewhere in the kernel rather than a
hand-rolled __PASTE to craft a unique id.
Also use __maybe_unused rather than (void) to signify that a
variable, althrough written to, may not actually be used.
v2:
- Move assignment to declaration (Christian)
- Declare the retry pointer as void *const.
Signed-off-by: Thomas Hellström <thomas.hellstrom@linux.intel.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Link: https://patch.msgid.link/20260520101616.41284-3-thomas.hellstrom@linux.intel.com
Nobody makes any use of it. Possible internal future users can
instead use the _index variable. External users shouldn't use
it since the array it's pointing into is internal drm_exec state.
v2:
- Use a unique id for the loop variable (Christian)
Assisted-by: GitHub Copilot:claude-sonnet-4.6
Signed-off-by: Thomas Hellström <thomas.hellstrom@linux.intel.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Link: https://patch.msgid.link/20260520101616.41284-2-thomas.hellstrom@linux.intel.com
The pinctrl_generic_to_map() and pinctrl_generic_pins_function_dt_node_to_map()
functions are built whenever CONFIG_GENERIC_PINCTRL is enabled, including
configurations without CONFIG_OF.
When CONFIG_OF is disabled, the dummy definitions are also present in the header,
which causes the build to fail:
drivers/pinctrl/pinctrl-generic.c:20:5: error: conflicting types for 'pinctrl_generic_to_map'; have 'int(struct pinctrl_dev *, struct device_node *, struct device_node *, struct pinctrl_map **, unsigned int *, unsigned int *, const char **, unsigned int, const char **, unsigned int *, unsigned int)'
20 | int pinctrl_generic_to_map(struct pinctrl_dev *pctldev, struct device_node *parent,
| ^~~~~~~~~~~~~~~~~~~~~~
In file included from drivers/pinctrl/pinctrl-generic.c:16:
drivers/pinctrl/pinconf.h:193:1: note: previous definition of 'pinctrl_generic_to_map' with type 'int(struct pinctrl_dev *, struct device_node *, struct device_node *, struct pinctrl_map **, unsigned int *, unsigned int *, const char **, unsigned int, const char **, unsigned int *, void *)'
193 | pinctrl_generic_to_map(struct pinctrl_dev *pctldev, struct device_node *parent,
| ^~~~~~~~~~~~~~~~~~~~~~
drivers/pinctrl/pinctrl-generic.c:130:5: error: redefinition of 'pinctrl_generic_pins_function_dt_node_to_map'
130 | int pinctrl_generic_pins_function_dt_node_to_map(struct pinctrl_dev *pctldev,
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
drivers/pinctrl/pinconf.h:184:1: note: previous definition of 'pinctrl_generic_pins_function_dt_node_to_map' with type 'int(struct pinctrl_dev *, struct device_node *, struct pinctrl_map **, unsigned int *)'
184 | pinctrl_generic_pins_function_dt_node_to_map(struct pinctrl_dev *pctldev,
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
Removing either set of definitions is sufficient to avoid the problem.
Remove the copy from the header for simplicity.
Fixes: aaaf31be04 ("pinctrl: extract pinctrl_generic_to_map() from pinctrl_generic_pins_function_dt_node_to_map()")
Fixes: 43722575e5 ("pinctrl: add generic functions + pins mapper")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Conor Dooley <conor.dooley@microchip.com>
Signed-off-by: Linus Walleij <linusw@kernel.org>
