Before probing the NETC switch driver, some pre-initialization needs to
be set in NETCMIX and IERB to ensure that the switch can work properly.
For example, i.MX94 NETC switch has three external ports and each port
is bound to a link. And each link needs to be configured so that it can
work properly, such as I/O variant and MII protocol.
In addition, the switch port 2 (MAC 2) and ENETC 0 (MAC 3) share the same
parallel interface, they cannot be used at the same time due to the SoC
constraint. And the MAC selection is controlled by the mac2_mac3_sel bit
of EXT_PIN_CONTROL register. Currently, the interface is set for ENETC 0
by default unless the switch port 2 is enabled in the DT node.
Like ENETC, each external port of the NETC switch can manage its external
PHY through its port MDIO registers. And the port can only access its own
external PHY by setting the PHY address to the LaBCR[MDIO_PHYAD_PRTAD].
If the accessed PHY address is not equal to LaBCR[MDIO_PHYAD_PRTAD], then
the MDIO access initiated by port MDIO will be invalid.
Signed-off-by: Wei Fang <wei.fang@nxp.com>
Link: https://patch.msgid.link/20260518082506.1318236-4-wei.fang@nxp.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Add bindings for NETC switch. This switch is a PCIe function of NETC IP,
it supports advanced QoS with 8 traffic classes and 4 drop resilience
levels, and a full range of TSN standards capabilities. The switch CPU
port connects to an internal ENETC port, which is also a PCIe function
of NETC IP. So these two ports use a light-weight "pseudo MAC" instead
of a back-to-back MAC, because the "pseudo MAC" provides the delineation
between switch and ENETC, this translates to lower power (less logic and
memory) and lower delay (as there is no serialization delay across this
link).
Signed-off-by: Wei Fang <wei.fang@nxp.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Reviewed-by: Rob Herring (Arm) <robh@kernel.org>
Link: https://patch.msgid.link/20260518082506.1318236-3-wei.fang@nxp.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
The current description indicates that the 'dsa,member' property cannot
be set for a switch that is not part of any cluster. Vladimir thinks
that this is a case where the actual technical limitation was poorly
transposed into words when this restriction was first documented, in
commit 8c5ad1d617 ("net: dsa: Document new binding").
The true technical limitation is that many DSA tagging protocols are
topology-unaware, and always call dsa_conduit_find_user() with a
switch_id of 0. Specifying a custom "dsa,member" property with a
non-zero switch_id would break them.
Therefore, for topology-aware switches, it is fine to specify this
property for them, even if they are not part of any cluster. Our NETC
switch is a good example which is topology-aware, the switch_id is
carried in the switch tag, but the switch_id 0 is reserved for VEPA
switch and cannot be used, so we need to use this property to assign
a non-zero switch_id for it.
Suggested-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Wei Fang <wei.fang@nxp.com>
Acked-by: Rob Herring (Arm) <robh@kernel.org>
Link: https://patch.msgid.link/20260518082506.1318236-2-wei.fang@nxp.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
comp_register_videodev() allocates a video_device with
video_device_alloc() and releases it if video_register_device() fails.
This can double free the video_device when __video_register_device()
reaches device_register() and that call fails:
video_register_device()
-> __video_register_device()
-> device_register() fails
-> put_device(&vdev->dev)
-> v4l2_device_release()
-> vdev->release(vdev)
-> video_device_release(vdev)
comp_register_videodev()
-> video_device_release(mdev->vdev)
Use video_device_release_empty() while registering the device so that
registration failure paths do not free mdev->vdev through vdev->release().
comp_register_videodev() then releases mdev->vdev exactly once on failure.
Restore video_device_release() after successful registration so the
registered device keeps its normal lifetime handling.
This issue was found by a static analysis tool I am developing.
Fixes: eab231c039 ("staging: most: v4l2-aim: remove unnecessary label err_vbi_dev")
Signed-off-by: Guangshuo Li <lgs201920130244@gmail.com>
Link: https://patch.msgid.link/20260517111218.945796-1-lgs201920130244@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Rename the CamelCase variable 'Bpp' to 'bpp' in both the header
and implementation files to comply with Linux kernel coding style.
Issue found by checkpatch.
Signed-off-by: Rupesh Majhi <zoone.rupert@gmail.com>
Link: https://patch.msgid.link/20260517131918.197943-1-zoone.rupert@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This switch statement doesn't do anything in all of its branches. As
such we can clean it up, and only keep the assignment in the else block.
Signed-off-by: Jennifer Guo <guojy.bj@gmail.com>
Link: https://patch.msgid.link/20260517044330.8517-1-guojy.bj@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The 'g_noaccel', 'g_nomtrr' and 'g_dualview' variables are initialized
only during the init phase in the 'lynxfb_setup' function and never
changed. So, mark them as __ro_after_init.
Signed-off-by: Len Bao <len.bao@gmx.us>
Link: https://patch.msgid.link/20260516142326.36018-1-len.bao@gmx.us
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Propagate errno values from rtl8723bs_hal_xmitframe_enqueue()
through rtw_hal_xmitframe_enqueue() by returning the error code
directly.
Update rtw_hal_xmit() to explicitly map the boolean return
value of rtl8723bs_hal_xmit() to _SUCCESS/_FAIL, clarifying
the return semantics at the HAL boundary.
None of the callers of rtw_hal_xmitframe_enqueue() check the
return value, so they do not need to be updated. This change
does not affect runtime behavior.
Signed-off-by: Hungyu Lin <dennylin0707@gmail.com>
Link: https://patch.msgid.link/20260514100708.25031-6-dennylin0707@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Propagate errno values from rtw_xmit_classifier() through
rtw_xmitframe_enqueue(), and update the local enqueue caller
to check for non-zero return values.
Signed-off-by: Hungyu Lin <dennylin0707@gmail.com>
Link: https://patch.msgid.link/20260514100708.25031-5-dennylin0707@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Convert rtw_xmit_classifier() to return 0 on success and
negative error codes on failure.
Update the caller to check for non-zero return values and
preserve the existing _FAIL/_SUCCESS semantics.
Signed-off-by: Hungyu Lin <dennylin0707@gmail.com>
Link: https://patch.msgid.link/20260514100708.25031-4-dennylin0707@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The rtw_xmit_classifier() function is only used within
rtw_xmit.c. Move it above its caller and make it static to
limit its scope.
Signed-off-by: Hungyu Lin <dennylin0707@gmail.com>
Link: https://patch.msgid.link/20260514100708.25031-3-dennylin0707@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Simplify rtw_xmit_classifier() by removing the exit label and
using direct returns for error handling.
No functional change.
Signed-off-by: Hungyu Lin <dennylin0707@gmail.com>
Link: https://patch.msgid.link/20260514100708.25031-2-dennylin0707@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Convert the private helper _rtw_enqueue_cmd() to return 0 on
success instead of the legacy _SUCCESS value.
Keep rtw_enqueue_cmd() translating the result back to the
existing return convention for now.
No functional change intended.
Signed-off-by: Hungyu Lin <dennylin0707@gmail.com>
Link: https://patch.msgid.link/20260513213719.12246-5-dennylin0707@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Replace the goto exit pattern with direct returns to simplify
the control flow and improve readability.
No functional change intended.
Signed-off-by: Hungyu Lin <dennylin0707@gmail.com>
Link: https://patch.msgid.link/20260513213719.12246-4-dennylin0707@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The function _rtw_enqueue_cmd() is only used within rtw_cmd.c,
so make it static and remove the unnecessary declaration from
the header file.
Signed-off-by: Hungyu Lin <dennylin0707@gmail.com>
Link: https://patch.msgid.link/20260513213719.12246-3-dennylin0707@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Replace the goto exit pattern with a direct return to simplify
the control flow and improve readability.
No functional change intended.
Signed-off-by: Hungyu Lin <dennylin0707@gmail.com>
Link: https://patch.msgid.link/20260513213719.12246-2-dennylin0707@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Remove multiple consecutive blank lines in more hal/ files.
This fixes the following checkpatch.pl check:
CHECK: Please don't use multiple blank lines
Signed-off-by: Jennifer Guo <guojy.bj@gmail.com>
Link: https://patch.msgid.link/20260515175140.7439-1-guojy.bj@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Remove the TXDESC_64_BYTES code since it is not used as the macro
is not defined anywhere.
Signed-off-by: Andrei Khomenkov <khomenkov@mailbox.org>
Link: https://patch.msgid.link/20260515151253.8106-3-khomenkov@mailbox.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Remove the DBG_XMIT_BUF and DBG_XMIT_BUF_EXT code since it is
not used as the macros are not defined anywhere.
Signed-off-by: Andrei Khomenkov <khomenkov@mailbox.org>
Link: https://patch.msgid.link/20260515151253.8106-2-khomenkov@mailbox.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Remove multiple consecutive blank lines in hal/Hal* source and header
files.
This fixes the following checkpatch.pl check:
CHECK: Please don't use multiple blank lines
Signed-off-by: Jennifer Guo <guojy.bj@gmail.com>
Link: https://patch.msgid.link/20260514180642.4608-1-guojy.bj@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Remove multiple consecutive blank lines in hal/hal_* and hal/sdio_*
files.
This fixes the following checkpatch.pl check:
CHECK: Please don't use multiple blank lines
Signed-off-by: Jennifer Guo <guojy.bj@gmail.com>
Link: https://patch.msgid.link/20260513212747.50900-1-guojy.bj@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add a blank line between the WIFI_UNDER_WPS block and the
wifi_spec block to improve readability.
Signed-off-by: Salman Alghamdi <me@cipherat.com>
Reviewed-by: Luka Gejak <luka.gejak@linux.dev>
Link: https://patch.msgid.link/20260513203611.31872-7-me@cipherat.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Inline rtw_sitesurvey_cmd() directly in the if condition to reduce
line length.
Signed-off-by: Salman Alghamdi <me@cipherat.com>
Reviewed-by: Luka Gejak <luka.gejak@linux.dev>
Link: https://patch.msgid.link/20260513203611.31872-3-me@cipherat.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Remove `data = 0` initialization since the variable is reset each
time in the for loop.
Signed-off-by: Ahmet Sezgin Duran <ahmet@sezginduran.net>
Link: https://patch.msgid.link/20260512164124.188210-4-ahmet@sezginduran.net
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Invert the frequency validation conditions and use early returns
to reduce nesting and improve readability.
No functional changes.
Signed-off-by: Ahmet Sezgin Duran <ahmet@sezginduran.net>
Link: https://patch.msgid.link/20260512164124.188210-3-ahmet@sezginduran.net
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Remove unused header file includes from multiple source files to
declutter the include sections.
Also remove the unused CONFIG_MTRR include block after verifying
that no MTRR interfaces are used by the driver.
No functional changes.
Signed-off-by: Ahmet Sezgin Duran <ahmet@sezginduran.net>
Link: https://patch.msgid.link/20260512164124.188210-2-ahmet@sezginduran.net
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
cedrus_probe() initializes the media device before registering the video
device, the media controller, and the media device. If any of those later
steps fails, probe returns without calling media_device_cleanup(), so the
media device internals initialized by media_device_init() are left behind.
Add a media-device cleanup label to the probe unwind path and route video
registration failures through it as well.
Fixes: 50e761516f ("media: platform: Add Cedrus VPU decoder driver")
Cc: stable@vger.kernel.org
Reviewed-by: Paul Kocialkowski <paulk@sys-base.io>
Co-developed-by: Ijae Kim <ae878000@gmail.com>
Signed-off-by: Ijae Kim <ae878000@gmail.com>
Signed-off-by: Myeonghun Pak <mhun512@gmail.com>
Signed-off-by: Nicolas Dufresne <nicolas.dufresne@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil+cisco@kernel.org>
Add support for the RGA3 unit contained in the RK3588.
Only a basic feature set consisting of scaling and color conversion is
implemented. Currently unimplemented features include:
- Advanced formats like 10bit YUV, FBCE mode and Tile8x8 mode
- Background color (V4L2_CID_BG_COLOR)
- Configurable alpha value (V4L2_CID_ALPHA_COMPONENT)
- Image flipping (V4L2_CID_HFLIP and V4L2_CID_VFLIP)
- Image rotation (V4L2_CID_ROTATE)
- Image cropping/composing (VIDIOC_S_SELECTION)
- Only very basic output cropping for 1088 -> 1080 cases is implemented
The register address defines were copied from the
vendor Rockchip kernel sources and slightly adjusted to not start at 0
again for the cmd registers.
During testing it has been noted that the scaling of the hardware is
slightly incorrect. A test conversion of 128x128 RGBA to 256x256 RGBA
causes a slightly larger scaling. The scaling is suddle, as it seems
that the image is scaled to a 2px larger version and then cropped to
it's final size. Trying to use the RGA2 scaling factor calculation
didn't work. As the calculation matches the vendor kernel driver, no
further research has been utilized to check if there may be some kind of
better scaling factor calculation.
Furthermore comparing the RGA3 conversion with the GStreamer
videoconvertscale element, the chroma-site is different. A quick testing
didn't reveal a chroma-site that creates the same image with the
GStreamer Element. Also when converting from YUV to RGB the RGB values
differ by 1 or 2. This doesn't seem to be a colorspace conversion issue
but rather a slightly different precision on the calculation.
Reviewed-by: Nicolas Dufresne <nicolas.dufresne@collabora.com>
Signed-off-by: Sven Püschel <s.pueschel@pengutronix.de>
Signed-off-by: Nicolas Dufresne <nicolas.dufresne@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil+cisco@kernel.org>
Disable multi-core support in preparation of the RGA3 addition. The
RK3588 SoC features two equal RGA3 cores. This allows scheduling of the
work between both cores, which is not yet implemented. Until it is
implemented avoid exposing both cores as independent video devices to
prevent an ABI breakage when multi-core support is added.
This patch is copied from the Hantro driver patch to disable multi core
support by Sebastian Reichel. See
commit ccdeb8d57f ("media: hantro: Disable multicore support")
Link: https://lore.kernel.org/all/20240618183816.77597-4-sebastian.reichel@collabora.com/
Reviewed-by: Nicolas Dufresne <nicolas.dufresne@collabora.com>
Signed-off-by: Sven Püschel <s.pueschel@pengutronix.de>
Signed-off-by: Nicolas Dufresne <nicolas.dufresne@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil+cisco@kernel.org>
In preparation to the RGA3 addition add feature flags, which can limit
the exposed feature set of the video device, like rotating or selection
support. This is necessary as the RGA3 doesn't initially implement the
full feature set currently exposed by the driver.
Reviewed-by: Nicolas Dufresne <nicolas.dufresne@collabora.com>
Signed-off-by: Sven Püschel <s.pueschel@pengutronix.de>
Signed-off-by: Nicolas Dufresne <nicolas.dufresne@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil+cisco@kernel.org>
Move rga_fmt to rga-hw in preparation of the RGA3 addition, as the struct
contains many RGA2 specific values. They are used to write the correct
register values quickly based on the chosen format. Therefore the
pointer to the rga_fmt struct is kept but changed to an opaque void
pointer outside of the rga-hw.h.
To enumerate and set the correct formats, two helper functions need to
be exposed in the rga_hw struct:
enum_format just get's the vidioc_enum_fmt format and it's return value
is also returned from vidioc_enum_fmt. This is a simple pass-through,
as the implementation is very simple.
adjust_and_map_format is a simple abstraction around the previous
rga_find_format. But unlike rga_find_format, it always returns a valid
format. Therefore the passed format value is also a pointer to update
it in case the values are not supported by the hardware.
Due to the RGA3 supporting different formats on the capture and output
side, an additional parameter is_capture has been added to support
this use-case. The additional ctx parameter is also added to allow the
RGA3 to limit the colorimetry only if an RGB<->YCrCb transformation
happens.
Reviewed-by: Nicolas Dufresne <nicolas.dufresne@collabora.com>
Signed-off-by: Sven Püschel <s.pueschel@pengutronix.de>
Signed-off-by: Nicolas Dufresne <nicolas.dufresne@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil+cisco@kernel.org>
Remove the stride variable from rga_frame. Despite the comment it
didn't involve any calculation and is just a copy of the
plane_fmt[0].bytesperline value. Therefore avoid this struct member
and use the bytesperline value directly in the places where it is
required.
Also drop the dependency on the depth format member, which was only
used to calculate the stride of the default format. This is already done
by the v4l2_fill_pixfmt_mp_aligned helper and used as stride in try_fmt.
Therefore using it's value also for the default format stride is just
more consistent.
Reviewed-by: Nicolas Dufresne <nicolas.dufresne@collabora.com>
Signed-off-by: Sven Püschel <s.pueschel@pengutronix.de>
Signed-off-by: Nicolas Dufresne <nicolas.dufresne@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil+cisco@kernel.org>
The size member is only used for the mmu page table mapping.
Therefore avoid storing the value and instead only calculate it
in place. This also avoids the calculation entirely when an external
iommu is used.
Reviewed-by: Nicolas Dufresne <nicolas.dufresne@collabora.com>
Signed-off-by: Sven Püschel <s.pueschel@pengutronix.de>
Signed-off-by: Nicolas Dufresne <nicolas.dufresne@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil+cisco@kernel.org>
The RGA3 and the corresponding iommu share the interrupt. So in that
case, request a shared interrupt so that the iommu driver can request
it as well.
Signed-off-by: Michael Olbrich <m.olbrich@pengutronix.de>
Reviewed-by: Nicolas Dufresne <nicolas.dufresne@collabora.com>
Signed-off-by: Sven Püschel <s.pueschel@pengutronix.de>
Signed-off-by: Nicolas Dufresne <nicolas.dufresne@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil+cisco@kernel.org>
In preparation for the RGA3 add support for external iommus. This is a
transition step to just disable the RGA2 specific mmu table setup code.
Currently a simple rga_hw struct field is used to set the internal iommu.
But to handle the case of more sophisticated detection mechanisms
(e.g. check for an iommu property in the device tree), it is abstracted
by an inline function.
Reviewed-by: Nicolas Dufresne <nicolas.dufresne@collabora.com>
Signed-off-by: Sven Püschel <s.pueschel@pengutronix.de>
Signed-off-by: Nicolas Dufresne <nicolas.dufresne@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil+cisco@kernel.org>
Change the offset to dma_addresses, as the current naming is misleading.
The offset naming comes from the fact that it references the offset in
the mapped iommu address space. But from the hardware point of view this
is an address, as also pointed out by the register naming
(e.g. RGA_DST_Y_RGB_BASE_ADDR). Therefore also change the type to
dma_addr_t, as with an external iommu driver this would also be the
correct type.
This change is a preparation for the RGA3 support, which uses an external
iommu and therefore just gets an dma_addr_t for each buffer. The field
renaming allows to reuse the existing fields of rga_vb_buffer to store
these values.
Reviewed-by: Nicolas Dufresne <nicolas.dufresne@collabora.com>
Signed-off-by: Sven Püschel <s.pueschel@pengutronix.de>
Signed-off-by: Nicolas Dufresne <nicolas.dufresne@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil+cisco@kernel.org>
In preparation of the RGA3 support add a filed to the rga_hw struct
to specify the desired card type value. This allows the user to
differentiate the RGA2 and RGA3 video device nodes.
Reviewed-by: Nicolas Dufresne <nicolas.dufresne@collabora.com>
Signed-off-by: Sven Püschel <s.pueschel@pengutronix.de>
Signed-off-by: Nicolas Dufresne <nicolas.dufresne@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil+cisco@kernel.org>
Check the scaling factor to avoid potential problems. This is relevant
for the upcoming RGA3 support, as it can hang when the scaling factor
is exceeded.
The check is done at streamon when the other side is already streaming
to avoid incorrectly failing if the application configures the other
side after calling streamon. As try_fmt shouldn't be state aware,
it cannot be used to limit the format based on the scaling factor.
Therefore the check is done just before the actual streaming would be
started.
As the driver allows changing the rotation and selection while
streaming, add additional checks to ensure these changes
don't exceed the scaling factor.
Signed-off-by: Sven Püschel <s.pueschel@pengutronix.de>
Reviewed-by: Nicolas Dufresne <nicolas.dufresne@collabora.com>
Signed-off-by: Nicolas Dufresne <nicolas.dufresne@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil+cisco@kernel.org>
Reuse the command buffer contents instead of completely writing it
for every frame. Therefore we only need to replace the source and
destination addresses for each frame. This reduces the amount of CPU
and memory operations done in each frame. A new cmdbuf_dirty flag notes
if the cmdbuf has to be rewritten on the next frame.
The initial idea of initializing the cmdbuf on streamon broke the
ability to update controls while streaming (e.g. mirroring).
Signed-off-by: Sven Püschel <s.pueschel@pengutronix.de>
Reviewed-by: Nicolas Dufresne <nicolas.dufresne@collabora.com>
Signed-off-by: Nicolas Dufresne <nicolas.dufresne@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil+cisco@kernel.org>
Add an alignment setting to rga_hw to set the desired stride alignment.
As the RGA2 register for the stride counts in word units, the code
already divides the bytesperline value by 4 when writing it into the
register. Therefore fix the alignment to a multiple of 4 to avoid
potential off by one errors due from the division.
Reviewed-by: Nicolas Dufresne <nicolas.dufresne@collabora.com>
Signed-off-by: Sven Püschel <s.pueschel@pengutronix.de>
Signed-off-by: Nicolas Dufresne <nicolas.dufresne@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil+cisco@kernel.org>
Move the command buffer to the rga_ctx struct in preparation to reuse
an already prepared command buffer. This allows to split the command
buffer setup in a further commit to setup a template for the command
buffer at streamon and only update the buffer addresses in device_run
and trigger the command stream. No sync point is added, as one command
buffer should only be used for one conversion at a time.
Reviewed-by: Nicolas Dufresne <nicolas.dufresne@collabora.com>
Signed-off-by: Sven Püschel <s.pueschel@pengutronix.de>
Signed-off-by: Nicolas Dufresne <nicolas.dufresne@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil+cisco@kernel.org>
Calculate the x_div and y_div variables with the information from
v4l2_format_info instead of storing these in the rga_fmt struct.
Reviewed-by: Nicolas Dufresne <nicolas.dufresne@collabora.com>
Signed-off-by: Sven Püschel <s.pueschel@pengutronix.de>
Signed-off-by: Nicolas Dufresne <nicolas.dufresne@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil+cisco@kernel.org>
Avoid odd frame sizes for YUV formats, as they may cause undefined
behavior. This is done in preparation for the RGA3, which hangs when the
output format is set to 129x129 pixel YUV420 SP (NV12).
This requirement is documented explicitly for the RGA3 in section 5.6.3
of the RK3588 TRM Part 2. For the RGA2 the RK3588 TRM Part 2
(section 6.1.2) and RK3568 TRM Part 2 (section 14.2) only mentions the
x/y offsets and stride aligning requirements. But the vendor driver for
the RGA2 also contains checks for the width and height to be aligned to
2 bytes.
Reviewed-by: Nicolas Dufresne <nicolas.dufresne@collabora.com>
Signed-off-by: Sven Püschel <s.pueschel@pengutronix.de>
Signed-off-by: Nicolas Dufresne <nicolas.dufresne@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil+cisco@kernel.org>
In preparation for the RGA3 unit, move RGA2 specific parts from rga.c
to rga-hw.c and create a struct to reference the RGA2 specific functions
and formats. This also allows to remove the rga-hw.h reference from the
include list of the rga driver.
Also document the command finish interrupt with a dedicated define.
Reviewed-by: Nicolas Dufresne <nicolas.dufresne@collabora.com>
Signed-off-by: Sven Püschel <s.pueschel@pengutronix.de>
Signed-off-by: Nicolas Dufresne <nicolas.dufresne@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil+cisco@kernel.org>
Announce the capability to adjust the quantization and ycbcr_enc on the
capture side and check if the SET_CSC flag is set when the colorimetry
is changed. Furthermore copy the colorimetry from the output to the
capture side to fix the currently failing v4l2-compliance tests, which
expect exactly this behavior.
Reviewed-by: Nicolas Dufresne <nicolas.dufresne@collabora.com>
Signed-off-by: Sven Püschel <s.pueschel@pengutronix.de>
Signed-off-by: Nicolas Dufresne <nicolas.dufresne@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil+cisco@kernel.org>
Remove the redundant rga_frame variables width, height and color space.
The value of these variables is already contained in the pix member
of rga_frame. The code also keeps these values in sync. Therefore drop
them in favor of the existing pix member.
Reviewed-by: Nicolas Dufresne <nicolas.dufresne@collabora.com>
Signed-off-by: Sven Püschel <s.pueschel@pengutronix.de>
Signed-off-by: Nicolas Dufresne <nicolas.dufresne@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil+cisco@kernel.org>
