On DesignWare I3C controllers where IC_HAS_IBI_DATA=0 (such as versalnet),
the IBI_STS_CNT field (bits [28:24] of QUEUE_STATUS_LEVEL) is hardwired
to 0. The IBI status entry count is instead reported via IBI_BUF_BLR
(bits [23:16] of the same register).
irq_handle_ibis() was unconditionally reading IBI_STS_CNT, causing it to
always see 0 pending IBIs on versalnet and return early without draining
the IBI buffer. Since INTR_IBI_THLD_STAT is level-triggered against the
buffer fill level, this left the interrupt permanently asserted.
Detect IBI data capability at probe time by writing the IBI data threshold
field in QUEUE_THLD_CTRL and reading it back. Use the result to select the
correct register field in irq_handle_ibis().
Signed-off-by: Shubhrajyoti Datta <shubhrajyoti.datta@amd.com>
Link: https://patch.msgid.link/20260401084430.436059-1-shubhrajyoti.datta@amd.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Replace mutex_init()/mutex_destroy() with drmm_mutex_init() for the
VRAM manager lock. This leverages DRM managed infrastructure to
automatically destroy the mutex during device teardown, eliminating
manual mutex_destroy() calls in both the normal fini path and the
gpu_buddy_init() error path.
Assisted-by: Claude:claude-opus-4.6
Reviewed-by: Matthew Auld <matthew.auld@intel.com>
Reviewed-by: Matthew Brost <matthew.brost@intel.com>
Link: https://patch.msgid.link/20260429093138.3899280-2-tejas.upadhyay@intel.com
Signed-off-by: Tejas Upadhyay <tejas.upadhyay@intel.com>
Replace sprintf() function calls with sysfs_emit() and
sysfs_emit_at() function calls where appropriate. This will help
harden the driver and help modernize it. While at it, add missing
newlines at the end of some sysfs_emit() (formerly sprintf()) calls.
Signed-off-by: Maxwell Doose <m32285159@gmail.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Link: https://patch.msgid.link/20260421214837.20939-1-m32285159@gmail.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
On NPCM845, when a target on the I3C bus gets stuck holding SDA low,
the controller reports a false Master Request (MR) in-band interrupt
event. The driver handles this by emitting a STOP condition to restore
the bus.
However, the hardware quirk SVC_I3C_QUIRK_FALSE_SLVSTART indicates that
emitting a STOP condition may spuriously set the SLVSTART interrupt
status bit. In the Master Request case, this creates a feedback loop:
the STOP triggers a new SLVSTART event, the IRQ handler fires again,
the controller still reports an MR type, another STOP is emitted, and
the cycle repeats indefinitely, resulting in an IRQ storm that can lock
up the CPU.
Clear the SLVSTART status bit explicitly after emitting the STOP in the
Master Request IBI handler when the SVC_I3C_QUIRK_FALSE_SLVSTART quirk
is set. This breaks the feedback loop without affecting normal SLVSTART
processing, which is already guarded in the top-level IRQ handler by
checking that MSTATUS is in SLVREQ state.
Signed-off-by: Stanley Chu <yschu@nuvoton.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Link: https://patch.msgid.link/20260413005040.1211107-3-yschu@nuvoton.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
The NPCM845 I3C controller may raise a false SLVSTART interrupt. The
handler first latches MSTATUS and then clears SLVSTART. If a real IBI
request arrives after the handler latches MSTATUS but before it clears
the SLVSTART interrupt status, HW sets the SLVREQ state. However, the
handler still relies on the stale MSTATUS snapshot, returns early, and
misses the real IBI. No further interrupt is generated for this pending
IBI.
Re-read MSTATUS to obtain the latest state and avoid missing a real IBI
due to this race condition.
Fixes: 4dd12e944f ("i3c: master: svc: Fix npcm845 invalid slvstart event")
Signed-off-by: Stanley Chu <yschu@nuvoton.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Link: https://patch.msgid.link/20260413005040.1211107-2-yschu@nuvoton.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Jacob Keller says:
====================
Intel Wired LAN Update 2026-04-27 (ice, iavf)
Petr Oros from RedHat has accumulated a number of fixes for the Intel ice
and iavf drivers, bundled together in this series.
First, a series of 4 fixes to resolve issues with the iavf driver logic for
handling VLAN filters. This includes keeping VLAN filters while the
interface is brought down, waiting for confirmation on filter deletion
before deleting filters from the driver tracking structures, and handling
the VIRTCHNL_OP_ADD_VLAN for the old v1 VLAN_ADD command.
A fix for a crash in ice_reset_all_vfs(), properly checking for errors when
ice_vf_rebuild_vsi() fails.
A fix for a possible infinite recursion in ice_cfg_tx_topo() that occurs
when trying to apply invalid Tx topology configuration.
A fix to initialize the SMA pins in the DPLL subsystem properly.
A fix to change the SMA and U.FL pin state for paired pins, ensuring that
all flows changing one pin will also update its shared pin appropriately.
A preparatory patch to export __dpll_pin_change_ntf() so that drivers can
notify pin changes while already holding the dpll_lock.
A fix to ensure DPLL notifications are sent for the software-controlled
pins which wrap the physical CGU input/output pins.
A fix to add DPLL notifications for peer pins when changing the SMA or U.FL
pins, ensuring DPLL subsystem is notified about the paired connected pins.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
====================
Link: https://patch.msgid.link/20260427-jk-iwl-net-petr-oros-fixes-v1-0-cdcb48303fd8@intel.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
SMA and U.FL pins share physical signal paths in pairs (SMA1/U.FL1 and
SMA2/U.FL2). When one pin's state changes via a PCA9575 GPIO write,
the paired pin's state also changes, but no notification is sent for
the peer pin. Userspace consumers monitoring the peer via dpll netlink
subscribe never learn about the update.
Add ice_dpll_sw_pin_notify_peer() which sends a change notification for
the paired SW pin. Call it from ice_dpll_pin_sma_direction_set(),
ice_dpll_sma_pin_state_set(), and ice_dpll_ufl_pin_state_set() after
pf->dplls.lock is released. Use __dpll_pin_change_ntf() because
dpll_lock is still held by the dpll netlink layer (dpll_pin_pre_doit).
Fixes: 2dd5d03c77 ("ice: redesign dpll sma/u.fl pins control")
Signed-off-by: Petr Oros <poros@redhat.com>
Tested-by: Alexander Nowlin <alexander.nowlin@intel.com>
Reviewed-by: Arkadiusz Kubalewski <arkadiusz.kubalewski@intel.com>
Reviewed-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Link: https://patch.msgid.link/20260427-jk-iwl-net-petr-oros-fixes-v1-11-cdcb48303fd8@intel.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
The SMA/U.FL pin redesign (commit 2dd5d03c77 ("ice: redesign dpll
sma/u.fl pins control")) introduced software-controlled pins that wrap
backing CGU input/output pins, but never updated the notification and
data paths to propagate pin events to these SW wrappers.
The periodic work sends dpll_pin_change_ntf() only for direct CGU input
pins. SW pins that wrap these inputs never receive change or phase
offset notifications, so userspace consumers such as synce4l monitoring
SMA pins via dpll netlink never learn about state transitions or phase
offset updates. Similarly, ice_dpll_phase_offset_get() reads the SW
pin's own phase_offset field which is never updated; the PPS monitor
writes to the backing CGU input's field instead.
Fix by introducing ice_dpll_pin_ntf(), a wrapper around
dpll_pin_change_ntf() that also notifies any registered SMA/U.FL pin
whose backing CGU input matches. Replace all direct
dpll_pin_change_ntf() calls in the periodic notification paths with
this wrapper. Fix ice_dpll_phase_offset_get() to return the backing
CGU input's phase_offset for input-direction SW pins.
Fixes: 2dd5d03c77 ("ice: redesign dpll sma/u.fl pins control")
Signed-off-by: Petr Oros <poros@redhat.com>
Tested-by: Alexander Nowlin <alexander.nowlin@intel.com>
Reviewed-by: Arkadiusz Kubalewski <arkadiusz.kubalewski@intel.com>
Reviewed-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Reviewed-by: Ivan Vecera <ivecera@redhat.com>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Link: https://patch.msgid.link/20260427-jk-iwl-net-petr-oros-fixes-v1-10-cdcb48303fd8@intel.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Export __dpll_pin_change_ntf() so that drivers can send pin change
notifications from within pin callbacks, which are already called
under dpll_lock. Using dpll_pin_change_ntf() in that context would
deadlock.
Add lockdep_assert_held() to catch misuse without the lock held.
Acked-by: Vadim Fedorenko <vadim.fedorenko@linux.dev>
Signed-off-by: Ivan Vecera <ivecera@redhat.com>
Signed-off-by: Petr Oros <poros@redhat.com>
Tested-by: Alexander Nowlin <alexander.nowlin@intel.com>
Reviewed-by: Arkadiusz Kubalewski <arkadiusz.kubalewski@intel.com>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Link: https://patch.msgid.link/20260427-jk-iwl-net-petr-oros-fixes-v1-9-cdcb48303fd8@intel.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
SMA and U.FL pins share physical signal paths in pairs (SMA1/U.FL1 and
SMA2/U.FL2) controlled by the PCA9575 GPIO expander. Each pair can
only have one active pin at a time: SMA1 output and U.FL1 output share
the same CGU output, SMA2 input and U.FL2 input share the same CGU
input. The PCA9575 register bits determine which connector in each
pair owns the signal path.
The driver does not account for this pairing in two places:
ice_dpll_ufl_pin_state_set() modifies PCA9575 bits and disables the
backing CGU pin without checking whether the U.FL pin is currently
active. Disconnecting an already inactive U.FL pin flips bits that
the paired SMA pin relies on, breaking its connection.
ice_dpll_sma_direction_set() does not propagate direction changes to
the paired U.FL pin. For SMA2/U.FL2 the ICE_SMA2_UFL2_RX_DIS bit is
never managed, so U.FL2 stays disconnected after SMA2 switches to
output. For both pairs the backing CGU pin of the U.FL side is never
enabled when a direction change activates it, so userspace sees the
pin as disconnected even though the routing is correct.
Fix by guarding the U.FL disconnect path against inactive pins and by
updating the paired U.FL pin fully on SMA direction changes: manage
ICE_SMA2_UFL2_RX_DIS for the SMA2/U.FL2 pair and enable the backing
CGU pin whenever the peer becomes active.
Fixes: 2dd5d03c77 ("ice: redesign dpll sma/u.fl pins control")
Signed-off-by: Petr Oros <poros@redhat.com>
Tested-by: Alexander Nowlin <alexander.nowlin@intel.com>
Reviewed-by: Arkadiusz Kubalewski <arkadiusz.kubalewski@intel.com>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Link: https://patch.msgid.link/20260427-jk-iwl-net-petr-oros-fixes-v1-8-cdcb48303fd8@intel.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
The DPLL SMA/U.FL pin redesign introduced ice_dpll_sw_pin_frequency_get()
which gates frequency reporting on the pin's active flag. This flag is
determined by ice_dpll_sw_pins_update() from the PCA9575 GPIO expander
state. Before the redesign, SMA pins were exposed as direct HW
input/output pins and ice_dpll_frequency_get() returned the CGU
frequency unconditionally — the PCA9575 state was never consulted.
The PCA9575 powers on with all outputs high, setting ICE_SMA1_DIR_EN,
ICE_SMA1_TX_EN, ICE_SMA2_DIR_EN and ICE_SMA2_TX_EN. Nothing in the
driver writes the register during initialization, so
ice_dpll_sw_pins_update() sees all pins as inactive and
ice_dpll_sw_pin_frequency_get() permanently returns 0 Hz for every
SW pin.
Fix this by writing a default SMA configuration in
ice_dpll_init_info_sw_pins(): clear all SMA bits, then set SMA1 and
SMA2 as active inputs (DIR_EN=0) with U.FL1 output and U.FL2 input
disabled. Each SMA/U.FL pair shares a physical signal path so only
one pin per pair can be active at a time. U.FL pins still report
frequency 0 after this fix: U.FL1 (output-only) is disabled by
ICE_SMA1_TX_EN which keeps the TX output buffer off, and U.FL2
(input-only) is disabled by ICE_SMA2_UFL2_RX_DIS. They can be
activated by changing the corresponding SMA pin direction via dpll
netlink.
Fixes: 2dd5d03c77 ("ice: redesign dpll sma/u.fl pins control")
Signed-off-by: Petr Oros <poros@redhat.com>
Reviewed-by: Ivan Vecera <ivecera@redhat.com>
Reviewed-by: Arkadiusz Kubalewski <arkadiusz.kubalewski@intel.com>
Tested-by: Alexander Nowlin <alexander.nowlin@intel.com>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Link: https://patch.msgid.link/20260427-jk-iwl-net-petr-oros-fixes-v1-7-cdcb48303fd8@intel.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
On certain E810 configurations where firmware supports Tx scheduler
topology switching (tx_sched_topo_comp_mode_en), ice_cfg_tx_topo()
may need to apply a new 5-layer or 9-layer topology from the DDP
package. If the AQ command to set the topology fails (e.g. due to
invalid DDP data or firmware limitations), the global configuration
lock must still be cleared via a CORER reset.
Commit 86aae43f21 ("ice: don't leave device non-functional if Tx
scheduler config fails") correctly fixed this by refactoring
ice_cfg_tx_topo() to always trigger CORER after acquiring the global
lock and re-initialize hardware via ice_init_hw() afterwards.
However, commit 8a37f9e2ff ("ice: move ice_deinit_dev() to the end
of deinit paths") later moved ice_init_dev_hw() into ice_init_hw(),
breaking the reinit path introduced by 86aae43f21. This creates an
infinite recursive call chain:
ice_init_hw()
ice_init_dev_hw()
ice_cfg_tx_topo() # topology change needed
ice_deinit_hw()
ice_init_hw() # reinit after CORER
ice_init_dev_hw() # recurse
ice_cfg_tx_topo()
... # stack overflow
Fix by moving ice_init_dev_hw() back out of ice_init_hw() and calling
it explicitly from ice_probe() and ice_devlink_reinit_up(). The third
caller, ice_cfg_tx_topo(), intentionally does not need ice_init_dev_hw()
during its reinit, it only needs the core HW reinitialization. This
breaks the recursion cleanly without adding flags or guards.
The deinit ordering changes from commit 8a37f9e2ff ("ice: move
ice_deinit_dev() to the end of deinit paths") which fixed slow rmmod
are preserved, only the init-side placement of ice_init_dev_hw() is
reverted.
Fixes: 8a37f9e2ff ("ice: move ice_deinit_dev() to the end of deinit paths")
Signed-off-by: Petr Oros <poros@redhat.com>
Reviewed-by: Paul Menzel <pmenzel@molgen.mpg.de>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Tested-by: Alexander Nowlin <alexander.nowlin@intel.com>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Link: https://patch.msgid.link/20260427-jk-iwl-net-petr-oros-fixes-v1-6-cdcb48303fd8@intel.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
ice_reset_all_vfs() ignores the return value of ice_vf_rebuild_vsi().
When the VSI rebuild fails (e.g. during NVM firmware update via
nvmupdate64e), ice_vsi_rebuild() tears down the VSI on its error path,
leaving txq_map and rxq_map as NULL. The subsequent unconditional call
to ice_vf_post_vsi_rebuild() leads to a NULL pointer dereference in
ice_ena_vf_q_mappings() when it accesses vsi->txq_map[0].
The single-VF reset path in ice_reset_vf() already handles this
correctly by checking the return value of ice_vf_reconfig_vsi() and
skipping ice_vf_post_vsi_rebuild() on failure.
Apply the same pattern to ice_reset_all_vfs(): check the return value
of ice_vf_rebuild_vsi() and skip ice_vf_post_vsi_rebuild() and
ice_eswitch_attach_vf() on failure. The VF is left safely disabled
(ICE_VF_STATE_INIT not set, VFGEN_RSTAT not set to VFACTIVE) and can
be recovered via a VFLR triggered by a PCI reset of the VF
(sysfs reset or driver rebind).
Note that this patch does not prevent the VF VSI rebuild from failing
during NVM update — the underlying cause is firmware being in a
transitional state while the EMP reset is processed, which can cause
Admin Queue commands (ice_add_vsi, ice_cfg_vsi_lan) to fail. This
patch only prevents the subsequent NULL pointer dereference that
crashes the kernel when the rebuild does fail.
crash> bt
PID: 50795 TASK: ff34c9ee708dc680 CPU: 1 COMMAND: "kworker/u512:5"
#0 [ff72159bcfe5bb50] machine_kexec at ffffffffaa8850ee
#1 [ff72159bcfe5bba8] __crash_kexec at ffffffffaaa15fba
#2 [ff72159bcfe5bc68] crash_kexec at ffffffffaaa16540
#3 [ff72159bcfe5bc70] oops_end at ffffffffaa837eda
#4 [ff72159bcfe5bc90] page_fault_oops at ffffffffaa893997
#5 [ff72159bcfe5bce8] exc_page_fault at ffffffffab528595
#6 [ff72159bcfe5bd10] asm_exc_page_fault at ffffffffab600bb2
[exception RIP: ice_ena_vf_q_mappings+0x79]
RIP: ffffffffc0a85b29 RSP: ff72159bcfe5bdc8 RFLAGS: 00010206
RAX: 00000000000f0000 RBX: ff34c9efc9c00000 RCX: 0000000000000000
RDX: 0000000000000000 RSI: 0000000000000010 RDI: ff34c9efc9c00000
RBP: ff34c9efc27d4828 R8: 0000000000000093 R9: 0000000000000040
R10: ff34c9efc27d4828 R11: 0000000000000040 R12: 0000000000100000
R13: 0000000000000010 R14: R15:
ORIG_RAX: ffffffffffffffff CS: 0010 SS: 0018
#7 [ff72159bcfe5bdf8] ice_sriov_post_vsi_rebuild at ffffffffc0a85e2e [ice]
#8 [ff72159bcfe5be08] ice_reset_all_vfs at ffffffffc0a920b4 [ice]
#9 [ff72159bcfe5be48] ice_service_task at ffffffffc0a31519 [ice]
#10 [ff72159bcfe5be88] process_one_work at ffffffffaa93dca4
#11 [ff72159bcfe5bec8] worker_thread at ffffffffaa93e9de
#12 [ff72159bcfe5bf18] kthread at ffffffffaa946663
#13 [ff72159bcfe5bf50] ret_from_fork at ffffffffaa8086b9
The panic occurs attempting to dereference the NULL pointer in RDX at
ice_sriov.c:294, which loads vsi->txq_map (offset 0x4b8 in ice_vsi).
The faulting VSI is an allocated slab object but not fully initialized
after a failed ice_vsi_rebuild():
crash> struct ice_vsi 0xff34c9efc27d4828
netdev = 0x0,
rx_rings = 0x0,
tx_rings = 0x0,
q_vectors = 0x0,
txq_map = 0x0,
rxq_map = 0x0,
alloc_txq = 0x10,
num_txq = 0x10,
alloc_rxq = 0x10,
num_rxq = 0x10,
The nvmupdate64e process was performing NVM firmware update:
crash> bt 0xff34c9edd1a30000
PID: 49858 TASK: ff34c9edd1a30000 CPU: 1 COMMAND: "nvmupdate64e"
#0 [ff72159bcd617618] __schedule at ffffffffab5333f8
#4 [ff72159bcd617750] ice_sq_send_cmd at ffffffffc0a35347 [ice]
#5 [ff72159bcd6177a8] ice_sq_send_cmd_retry at ffffffffc0a35b47 [ice]
#6 [ff72159bcd617810] ice_aq_send_cmd at ffffffffc0a38018 [ice]
#7 [ff72159bcd617848] ice_aq_read_nvm at ffffffffc0a40254 [ice]
#8 [ff72159bcd6178b8] ice_read_flat_nvm at ffffffffc0a4034c [ice]
#9 [ff72159bcd617918] ice_devlink_nvm_snapshot at ffffffffc0a6ffa5 [ice]
dmesg:
ice 0000:13:00.0: firmware recommends not updating fw.mgmt, as it
may result in a downgrade. continuing anyways
ice 0000:13:00.1: ice_init_nvm failed -5
ice 0000:13:00.1: Rebuild failed, unload and reload driver
Fixes: 12bb018c53 ("ice: Refactor VF reset")
Signed-off-by: Petr Oros <poros@redhat.com>
Tested-by: Rafal Romanowski <rafal.romanowski@intel.com>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Link: https://patch.msgid.link/20260427-jk-iwl-net-petr-oros-fixes-v1-5-cdcb48303fd8@intel.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
The V1 ADD_VLAN opcode had no success handler; filters sent via V1
stayed in ADDING state permanently. Add a fallthrough case so V1
filters also transition ADDING -> ACTIVE on PF confirmation.
Critically, add an `if (v_retval) break` guard: the error switch in
iavf_virtchnl_completion() does NOT return after handling errors,
it falls through to the success switch. Without this guard, a
PF-rejected ADD would incorrectly mark ADDING filters as ACTIVE,
creating a driver/HW mismatch where the driver believes the filter
is installed but the PF never accepted it.
For V2, this is harmless: iavf_vlan_add_reject() in the error
block already kfree'd all ADDING filters, so the success handler
finds nothing to transition.
Fixes: 968996c070 ("iavf: Fix VLAN_V2 addition/rejection")
Signed-off-by: Petr Oros <poros@redhat.com>
Reviewed-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Tested-by: Rafal Romanowski <rafal.romanowski@intel.com>
Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Link: https://patch.msgid.link/20260427-jk-iwl-net-petr-oros-fixes-v1-4-cdcb48303fd8@intel.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
The VLAN filter DELETE path was asymmetric with the ADD path: ADD
waits for PF confirmation (ADD -> ADDING -> ACTIVE), but DELETE
immediately frees the filter struct after sending the DEL message
without waiting for the PF response.
This is problematic because:
- If the PF rejects the DEL, the filter remains in HW but the driver
has already freed the tracking structure, losing sync.
- Race conditions between DEL pending and other operations
(add, reset) cannot be properly resolved if the filter struct
is already gone.
Add IAVF_VLAN_REMOVING state to make the DELETE path symmetric:
REMOVE -> REMOVING (send DEL) -> PF confirms -> kfree
-> PF rejects -> ACTIVE
In iavf_del_vlans(), transition filters from REMOVE to REMOVING
instead of immediately freeing them. The new DEL completion handler
in iavf_virtchnl_completion() frees filters on success or reverts
them to ACTIVE on error.
Update iavf_add_vlan() to handle the REMOVING state: if a DEL is
pending and the user re-adds the same VLAN, queue it for ADD so
it gets re-programmed after the PF processes the DEL.
The !VLAN_FILTERING_ALLOWED early-exit path still frees filters
directly since no PF message is sent in that case.
Also update iavf_del_vlan() to skip filters already in REMOVING
state: DEL has been sent to PF and the completion handler will
free the filter when PF confirms. Without this guard, the sequence
DEL(pending) -> user-del -> second DEL could cause the PF to return
an error for the second DEL (filter already gone), causing the
completion handler to incorrectly revert a deleted filter back to
ACTIVE.
Fixes: 968996c070 ("iavf: Fix VLAN_V2 addition/rejection")
Signed-off-by: Petr Oros <poros@redhat.com>
Reviewed-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Tested-by: Rafal Romanowski <rafal.romanowski@intel.com>
Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Link: https://patch.msgid.link/20260427-jk-iwl-net-petr-oros-fixes-v1-3-cdcb48303fd8@intel.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
When a VF goes down, the driver currently sends DEL_VLAN to the PF for
every VLAN filter (ACTIVE -> DISABLE -> send DEL -> INACTIVE), then
re-adds them all on UP (INACTIVE -> ADD -> send ADD -> ADDING ->
ACTIVE). This round-trip is unnecessary because:
1. The PF disables the VF's queues via VIRTCHNL_OP_DISABLE_QUEUES,
which already prevents all RX/TX traffic regardless of VLAN filter
state.
2. The VLAN filters remaining in PF HW while the VF is down is
harmless - packets matching those filters have nowhere to go with
queues disabled.
3. The DEL+ADD cycle during down/up creates race windows where the
VLAN filter list is incomplete. With spoofcheck enabled, the PF
enables TX VLAN filtering on the first non-zero VLAN add, blocking
traffic for any VLANs not yet re-added.
Remove the entire DISABLE/INACTIVE state machinery:
- Remove IAVF_VLAN_DISABLE and IAVF_VLAN_INACTIVE enum values
- Remove iavf_restore_filters() and its call from iavf_open()
- Remove VLAN filter handling from iavf_clear_mac_vlan_filters(),
rename it to iavf_clear_mac_filters()
- Remove DEL_VLAN_FILTER scheduling from iavf_down()
- Remove all DISABLE/INACTIVE handling from iavf_del_vlans()
VLAN filters now stay ACTIVE across down/up cycles. Only explicit
user removal (ndo_vlan_rx_kill_vid) or PF/VF reset triggers VLAN
filter deletion/re-addition.
Fixes: ed1f5b58ea ("i40evf: remove VLAN filters on close")
Signed-off-by: Petr Oros <poros@redhat.com>
Reviewed-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Tested-by: Rafal Romanowski <rafal.romanowski@intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Link: https://patch.msgid.link/20260427-jk-iwl-net-petr-oros-fixes-v1-2-cdcb48303fd8@intel.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Rename the IAVF_VLAN_IS_NEW state to IAVF_VLAN_ADDING to better
describe what the state represents: an ADD request has been sent to
the PF and is waiting for a response.
This is a pure rename with no behavioral change, preparing for a
cleanup of the VLAN filter state machine.
Signed-off-by: Petr Oros <poros@redhat.com>
Reviewed-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Tested-by: Rafal Romanowski <rafal.romanowski@intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Link: https://patch.msgid.link/20260427-jk-iwl-net-petr-oros-fixes-v1-1-cdcb48303fd8@intel.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
shmob_drm_connector_create() can init the connector in two ways, based on
the 'if (sdev->pdata)':
1. manually in shmob_drm_connector_create(), or
2. delegating to drm_bridge_connector_init()
Whichever branch is taken, drm_connector_attach_encoder() is called
immediately after to attach the connector to the encoder.
Now drm_bridge_connector_init() calls drm_connector_attach_encoder() on the
connector so it is not needed anymore in case 2 and should be removed, but
it is still needed in case 1. Move drm_connector_attach_encoder() from the
common path to inside shmob_drm_connector_create() in order to get back to
a single drm_connector_attach_encoder() in both cases.
Tested-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Link: https://patch.msgid.link/20260423115550.444930-7-luca.ceresoli@bootlin.com
Signed-off-by: Luca Ceresoli <luca.ceresoli@bootlin.com>
drm_connector_attach_encoder() is now called by
drm_bridge_connector_init().
Reviewed-by: Liu Ying <victor.liu@nxp.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Link: https://patch.msgid.link/20260423115550.444930-5-luca.ceresoli@bootlin.com
Signed-off-by: Luca Ceresoli <luca.ceresoli@bootlin.com>
