ADC & I/Q calibrations could take infinite time to comple, since they
depend on received frames. In particular the I/Q mismatch calibration
requires receiving of OFDM frames for completion. But in the 2.4GHz
band, a station could receive only CCK frames for a very long time.
And while we wait for the completion of one of the mentioned
calibrations, the NF calibration is blocked. Moreover, in some
environments, I/Q calibration is unable to complete until a correct
noise calibration will be performed due to AGC behaviour.
In order to avoid delaying NF calibration on forever, limit the maximum
duration of ADCs & I/Q calibrations. If the calibration is not completed
within the maximum time, it will be interrupted and a next calibration
will be performed. The code that selects the next calibration has been
reworked to the loop so incompleted calibration will be respinned later.
Ð maximum calibration time of 30 seconds was selected to give the
calibration enough time to complete and to not interfere with the long
(NF) calibration.
Run tested with AR9220.
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200424004923.17129-7-ryazanov.s.a@gmail.com
Previously after the calibration validity period is over,
calibrations are invalidated in a one at time manner. So, for AR9002
family, which has three calibrations, the full recalibration interval
becomes 3 x ATH_RESTART_CALINTERVAL. And each next calibration will be
separated by the ATH_RESTART_CALINTERVAL time from a previous one.
It seems like it is better to do whole recalibration at once. Also, this
change makes the driver behaviour a little simpler. So, invalidate all
calibrations at once at the end of the calibration validity interval.
This change affects only AR9002 chips family, since the AR9003 utilize
only a single calibration.
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200424004923.17129-6-ryazanov.s.a@gmail.com
NF calibration and other elements of long calibration are usually faster
than ADCs & I/Q calibrations due to independence of receiption of the
OFDM signal. Moreover sometime I/Q calibration can not be completed at
all without preceding NF calibration. This is due to AGC, which has a
habit to block a weak signal without regular NF calibration. Thus, we do
not need to deferr the long calibration forever.
So, if the long calibration is requested, then deferr the ADCs & I/Q
calibration(s) and run the longcal (the NF calibration in particular) to
obtain fresh noise data.
Run tested with AR9220.
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200424004923.17129-5-ryazanov.s.a@gmail.com
Each of AGC & I/Q calibrations can take a long time. Long calibration
and NF calibration in particular are forbiden for parallel run with
ADC & I/Q calibrations. So, the chip could not be ready to perform the
long calibration at the time of request. And a request to perform the
long calibration may be lost.
In order to fix this, preserve the long calibration request as a
calibration state flag and restore the long calibration request each
time the calibration function is called again (i.e. on each subsequent
ivocation of the short calibration).
This feature will be twice useful after the next change, which will
make it possible to start the long calibration before all ADCs & I/Q
calibrations are completed.
Run tested with AR9220.
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200424004923.17129-4-ryazanov.s.a@gmail.com
The NFCAL_PENDING flag is set by the ath9k_hw_start_nfcal() routine,
so there is no reason to set it manually after calling it during the
AR9002 calibrations initialization.
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200424004923.17129-3-ryazanov.s.a@gmail.com
ADC calibration is only required for a 80 MHz sampling rate (i.e. for
40 MHz channels), when the chip utilizes the pair of ADCs in interleved
mode. Calibration on a 20 MHz channel will never be completed.
Previous channel check is trying to exclude all channels where the
calibration will get stuck. It effectively blocks the calibration run
for HT20 channels, but fails to exclude 20 MHz channels without HT (e.g.
legacy mode channels).
Fix this issue by reworking the channel check to explicitly allow ADCs
gain & DC offset calibrations for HT40 channels only. Also update the
complicated comment to make it clear that these calibrations are for
multi-ADC mode only.
Stuck ADCs calibration blocks the NF calibration, what could make it
impossible to work in a noisy evironment: too big Rx attentuation,
invalid RSSI value, etc. So this change is actually more of a NF
calibration fix rather then the ADC calibration fix.
Run tested with AR9220.
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200424004923.17129-2-ryazanov.s.a@gmail.com
When tx complete is disabled, all tx status will be set with status
HTT_TX_COMPL_STATE_ACK and indicate to mac80211 by ieee80211_tx_status,
then it does not have the statistics for retries and failed packets.
count of tx retries and tx failed of command "iw wlan0 station dump"
are both 0. If tx complete is not disabled, then firmware report the
tx status and ath10k indicate the status to mac80211, then mac80211
save the statistics and command "iw wlan0 station dump" show them.
for example:
localhost ~ # iw dev wlan0 station dump
Station 3c:28:6d:96:fd:69 (on wlan0)
inactive time: 5 ms
rx bytes: 1325012
rx packets: 6477
tx bytes: 85264
tx packets: 518
tx retries: 0
tx failed: 0
This patch only effect chips with tx complete disabled, e.g. SDIO.
with this patch, output of command "iw dev wlan0 station dump":
Station c4:04:15:5d:97:22 (on wlan0)
inactive time: 608 ms
rx bytes: 180366
rx packets: 991
tx bytes: 98765577
tx packets: 64624
tx retries: 14682
tx failed: 47086
Tested with QCA6174 SDIO with firmware WLAN.RMH.4.4.1-00042.
Signed-off-by: Wen Gong <wgong@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200423024134.10601-1-wgong@codeaurora.org
When run command "iw dev wlan0 station dump", the rx duration is 0.
When firmware indicate WMI_UPDATE_STATS_EVENTID, extended flag of
statsis not set by default, so firmware do not report rx duration.
one sample:
localhost # iw wlan0 station dump
Station c4:04:15:5d:97:22 (on wlan0)
inactive time: 48 ms
rx bytes: 21670
rx packets: 147
tx bytes: 11529
tx packets: 100
tx retries: 88
tx failed: 36
beacon loss: 1
beacon rx: 31
rx drop misc: 47
signal: -72 [-74, -75] dBm
signal avg: -71 [-74, -75] dBm
beacon signal avg: -71 dBm
tx bitrate: 54.0 MBit/s MCS 3 40MHz
rx bitrate: 1.0 MBit/s
rx duration: 0 us
This patch enable firmware's extened flag of stats by setting flag
WMI_TLV_STAT_PEER_EXTD of ar->fw_stats_req_mask which is set in
ath10k_core_init_firmware_features via WMI_REQUEST_STATS_CMDID.
After apply this patch, rx duration show value with the command:
Station c4:04:15:5d:97:22 (on wlan0)
inactive time: 883 ms
rx bytes: 44289
rx packets: 265
tx bytes: 10838
tx packets: 93
tx retries: 899
tx failed: 103
beacon loss: 0
beacon rx: 78
rx drop misc: 46
signal: -71 [-74, -76] dBm
signal avg: -70 [-74, -76] dBm
beacon signal avg: -70 dBm
tx bitrate: 54.0 MBit/s MCS 3 40MHz
rx bitrate: 1.0 MBit/s
rx duration: 358004 us
This patch do not have side effect for all chips, because function
ath10k_debug_fw_stats_request is already exported to debugfs
"fw_stats" and WMI_REQUEST_STATS_CMDID is safely sent after condition
checked by ath10k_peer_stats_enabled in ath10k_sta_statistics.
Tested with QCA6174 SDIO with firmware WLAN.RMH.4.4.1-00042.
Signed-off-by: Wen Gong <wgong@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200423022758.5365-1-wgong@codeaurora.org
we are sending the reo flush command for the deleted peer
tid after the ageout period reaches 1 second. This handling
causes reo ring get full when more than 128 clients are
disconnected continuously. so added the count for flush list
and reo flush command is triggered after the list count reaches
the threshold value, it is configured as 64 (half of the reo ring).
This will avoid the situation where reo ring get full.
Signed-off-by: Karthikeyan Periyasamy <periyasa@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1587552378-4884-1-git-send-email-periyasa@codeaurora.org
sdio chip use DMA buffer to receive TX packet from ath10k, and it has
limitation of each buffer, if the packet size exceed the credit size,
it will trigger error in firmware.
Tested with QCA6174 SDIO with firmware
WLAN.RMH.4.4.1-00017-QCARMSWP-1.
Signed-off-by: Wen Gong <wgong@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200422084719.3479-1-wgong@codeaurora.org
The driver is allowing the invalid tx/rx chainmask configuration
(other than 1,3,7,15) set by the user. It causes the firmware
crash due to the invalid chainmask values.
Hence, reject the invalid chainmask values in the driver by not
sending the pdev set command to the firmware.
Tested hardware: QCA9888
Tested firmware: 10.4-3.10-00047
Signed-off-by: Maharaja Kennadyrajan <mkenna@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1587495512-29813-1-git-send-email-mkenna@codeaurora.org
The default credit size is 1792 bytes, but the IP mtu is 1500 bytes,
then it has about 290 bytes's waste for each data packet on sdio
transfer path for TX bundle, it will reduce the transmission utilization
ratio for data packet.
This patch enable the small credit size in firmware, firmware will use
the new credit size 1556 bytes, it will increase the transmission
utilization ratio for data packet on TX patch. It results in significant
performance improvement on TX path.
This patch only effect sdio chip, it will not effect PCI, SNOC etc.
Tested with QCA6174 SDIO with firmware
WLAN.RMH.4.4.1-00017-QCARMSWP-1.
Signed-off-by: Wen Gong <wgong@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200410061400.14231-3-wgong@codeaurora.org
The transmission utilization ratio for sdio bus for small packet is
slow, because the space and time cost for sdio bus is same for large
length packet and small length packet. So the speed of data for large
length packet is higher than small length.
Test result of different length of data:
data packet(byte) cost time(us) calculated rate(Mbps)
256 28 73
512 33 124
1024 35 234
1792 45 318
14336 168 682
28672 333 688
57344 660 695
This patch change the TX packet from single packet to a large length
bundle packet, max size is 32, it results in significant performance
improvement on TX path.
Also there's a fourth thread "ath10k_tx_complete_wq" added to ath10k as it
improves TCP RX throughput (values in Mbps):
TCP-RX TCP-TX UDP-RX UDP-TX
use workqueue_tx_complete 423 357 448 412
change it to ar->workqueue 410 360 449 414
change it to ar->workqueue_aux 405 339 446 401
This patch only effect sdio chip, it will not effect PCI, SNOC etc.
It only enable bundle for sdio chip.
Tested with QCA6174 SDIO with firmware
WLAN.RMH.4.4.1-00017-QCARMSWP-1.
Signed-off-by: Wen Gong <wgong@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200410061400.14231-2-wgong@codeaurora.org
The '==' expression itself is bool, no need to convert it to bool again.
This fixes the following coccicheck warning:
drivers/net/wireless/ath/ath11k/debug.c:198:57-62: WARNING: conversion
to bool not needed here
drivers/net/wireless/ath/ath11k/debug.c:218:58-63: WARNING: conversion
to bool not needed here
Signed-off-by: Jason Yan <yanaijie@huawei.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200420123745.4159-1-yanaijie@huawei.com
The '==' expression itself is bool, no need to convert it to bool again.
This fixes the following coccicheck warning:
drivers/net/wireless/ath/ath11k/dp_rx.c:255:46-51: WARNING: conversion
to bool not needed here
Signed-off-by: Jason Yan <yanaijie@huawei.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200420123718.3384-1-yanaijie@huawei.com
This patch is to set register to allow the mbox enter sleep status
if it does not have tx traffic and wakeup it if tx traffic arrive.
After mbox enter sleep status, the soc will enter sleep status by
firmware, this will save power. The power consume drops from about
90mW to about 10mW with this patch.
This patch only effect sdio chip.
Tested with QCA6174 SDIO with firmware WLAN.RMH.4.4.1-00029.
Signed-off-by: Wen Gong <wgong@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1587037859-28873-3-git-send-email-kvalo@codeaurora.org
Convert ath10k_hif_swap_mailbox() to a more generic op so that bus drivers can
do more than just swap the mailbox, for example set power save settings like in
the following sdio patch.
No functional changes, compile tested only.
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1587037859-28873-2-git-send-email-kvalo@codeaurora.org
IPQ8074 HW supports three TCL rings for tx. Currently these rings
are mapped based on the Access categories, viz. VO, VI, BE, BK.
In case, one of the traffic type dominates, then it could stress
the same tcl rings. Rather, it would be optimal to make use of all
the rings in a round robin fashion irrespective of the traffic type
so that the load could be evenly distributed among all the rings.
Also, in case the selected ring is busy or full, a retry mechanism
is used to ensure other available ring is selected without dropping
the packet.
In SMP systems, this change avoids a single CPU from getting hogged
when heavy traffic of same category is transmitted.
The tx completion interrupts corresponding to the used tcl ring
would be more which causes the assigned CPU to get hogged.
Distribution of tx packets to different tcl rings helps balance
this load.
Signed-off-by: Sriram R <srirrama@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1586782622-22570-1-git-send-email-srirrama@codeaurora.org
should not overwrite the error code. No buffer available then return
invalid. For other failures return the error code of actual failure.
Signed-off-by: Govindaraj Saminathan <gsamin@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1586776872-25766-1-git-send-email-gsamin@codeaurora.org
Rx_filter flags are set with default filter flags during
wifi up/down sequence even though the 'ext_rx_stats' debugfs
is enabled as 1. So, that we are not getting proper per peer
rx_stats.
Hence, fixing this by setting the missing rx_filter when
ext_rx_stats is already set/enabled.
Signed-off-by: Maharaja Kennadyrajan <mkenna@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1586538405-16226-3-git-send-email-mkenna@codeaurora.org
After setting fixed vht-rate if new station is trying to
assoc with mu_bfee cap, or if a sta is already connected
with mu_bfee cap then set the fixed vht-rate and
reconnecting the sta, FW assert is happening.
So to avoid this, reset the MU_BEAMFORMEE bit in vht->caps,
if mcs_index is invalid for nss 1.
Signed-off-by: Ritesh Singh <ritesi@codeaurora.org>
Signed-off-by: Maharaja Kennadyrajan <mkenna@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1586538405-16226-2-git-send-email-mkenna@codeaurora.org
Debugfs pdev entries should be cleaned up during the crash
on recovery. If not, mac register will fail for the reason
that it is already registered during core reconfigure.
Signed-off-by: Maharaja Kennadyrajan <mkenna@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1586538405-16226-1-git-send-email-mkenna@codeaurora.org
During RX, accessing the reo dest ring descriptor directly is consuming
a lot of CPU cycles. Accessing the descriptor after copying it locally
has improved CPU usage by around ~10-15% while measuring throughput
in RX DBTC test cases(all radios are involved in the throughput
measurement).
HW tested: IPQ8074
Signed-off-by: Manikanta Pubbisetty <mpubbise@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1586421797-885-1-git-send-email-mpubbise@codeaurora.org
Unlike CE interrupts, DP interrupts are not enabled/disabled at
source; they are enabled/disabled only at GIC level, therefore
it is required to set IRQ_DISABLE_UNLAZY flag to avoid spurious
interrupts.
Signed-off-by: Manikanta Pubbisetty <mpubbise@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1586421013-23025-1-git-send-email-mpubbise@codeaurora.org
Add the pdev index information in the peer object to validate
the peer creation. Ignore the peer creation request, if the given
MAC address is already present in the peer list with same radio.
If we allow the peer creation in above scenario, FW assert will happen.
Above scenario occurred in two cases, where Multiple AP VAP created in
the same radio.
1. when testing tool sends association request to two AP with same
MAC address
2. when a station do roaming from one AP VAP to another AP VAP.
Signed-off-by: Karthikeyan Periyasamy <periyasa@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1586343795-21422-1-git-send-email-periyasa@codeaurora.org
This sorts the actual field names too, potentially causing even more
chaos and confusion at merge time if you have edited the MAINTAINERS
file. But the end result is a more consistent layout, and hopefully
it's a one-time pain minimized by doing this just before the -rc1
release.
This was entirely scripted:
./scripts/parse-maintainers.pl --input=MAINTAINERS --output=MAINTAINERS --order
Requested-by: Joe Perches <joe@perches.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
They are all supposed to be sorted, but people who add new entries don't
always know the alphabet. Plus sometimes the entry names get edited,
and people don't then re-order the entry.
Let's see how painful this will be for merging purposes (the MAINTAINERS
file is often edited in various different trees), but Joe claims there's
relatively few patches in -next that touch this, and doing it just
before -rc1 is likely the best time. Fingers crossed.
This was scripted with
/scripts/parse-maintainers.pl --input=MAINTAINERS --output=MAINTAINERS
but then I also ended up manually upper-casing a few entry names that
stood out when looking at the end result.
Requested-by: Joe Perches <joe@perches.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
detection feature.
It addressed the case where a KVM guest triggers a split lock #AC and KVM
reinjects it into the guest which is not prepared to handle it.
Adds proper sanity checks which prevent the unconditional injection into
the guest and handles the #AC on the host side in the same way as user
space detections are handled. Depending on the detection mode it either
warns and disables detection for the task or kills the task if the mode is
set to fatal.
-----BEGIN PGP SIGNATURE-----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=8FbL
-----END PGP SIGNATURE-----
Merge tag 'x86-urgent-2020-04-12' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 fixes from Thomas Gleixner:
"A set of three patches to fix the fallout of the newly added split
lock detection feature.
It addressed the case where a KVM guest triggers a split lock #AC and
KVM reinjects it into the guest which is not prepared to handle it.
Add proper sanity checks which prevent the unconditional injection
into the guest and handles the #AC on the host side in the same way as
user space detections are handled. Depending on the detection mode it
either warns and disables detection for the task or kills the task if
the mode is set to fatal"
* tag 'x86-urgent-2020-04-12' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
KVM: VMX: Extend VMXs #AC interceptor to handle split lock #AC in guest
KVM: x86: Emulate split-lock access as a write in emulator
x86/split_lock: Provide handle_guest_split_lock()
- Fix the time_for_children symlink in /proc/$PID/ so it properly reflects
that it part of the 'time' namespace
- Add the missing userns limit for the allowed number of time namespaces,
which was half defined but the actual array member was not added. This
went unnoticed as the array has an exessive empty member at the end but
introduced a user visible regression as the output was corrupted.
- Prevent further silent ucount corruption by adding a BUILD_BUG_ON() to
catch half updated data.
-----BEGIN PGP SIGNATURE-----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=wOiC
-----END PGP SIGNATURE-----
Merge tag 'timers-urgent-2020-04-12' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull time(keeping) updates from Thomas Gleixner:
- Fix the time_for_children symlink in /proc/$PID/ so it properly
reflects that it part of the 'time' namespace
- Add the missing userns limit for the allowed number of time
namespaces, which was half defined but the actual array member was
not added. This went unnoticed as the array has an exessive empty
member at the end but introduced a user visible regression as the
output was corrupted.
- Prevent further silent ucount corruption by adding a BUILD_BUG_ON()
to catch half updated data.
* tag 'timers-urgent-2020-04-12' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
ucount: Make sure ucounts in /proc/sys/user don't regress again
time/namespace: Add max_time_namespaces ucount
time/namespace: Fix time_for_children symlink
- Deduplicate the average computations in the scheduler core and the fair
class code.
- Fix a raise between runtime distribution and assignement which can cause
exceeding the quota by up to 70%.
- Prevent negative results in the imbalanace calculation
- Remove a stale warning in the workqueue code which can be triggered
since the call site was moved out of preempt disabled code. It's a false
positive.
- Deduplicate the print macros for procfs
- Add the ucmap values to the SCHED_DEBUG procfs output for completness
-----BEGIN PGP SIGNATURE-----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=BVqY
-----END PGP SIGNATURE-----
Merge tag 'sched-urgent-2020-04-12' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull scheduler fixes/updates from Thomas Gleixner:
- Deduplicate the average computations in the scheduler core and the
fair class code.
- Fix a raise between runtime distribution and assignement which can
cause exceeding the quota by up to 70%.
- Prevent negative results in the imbalanace calculation
- Remove a stale warning in the workqueue code which can be triggered
since the call site was moved out of preempt disabled code. It's a
false positive.
- Deduplicate the print macros for procfs
- Add the ucmap values to the SCHED_DEBUG procfs output for completness
* tag 'sched-urgent-2020-04-12' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
sched/debug: Add task uclamp values to SCHED_DEBUG procfs
sched/debug: Factor out printing formats into common macros
sched/debug: Remove redundant macro define
sched/core: Remove unused rq::last_load_update_tick
workqueue: Remove the warning in wq_worker_sleeping()
sched/fair: Fix negative imbalance in imbalance calculation
sched/fair: Fix race between runtime distribution and assignment
sched/fair: Align rq->avg_idle and rq->avg_scan_cost
- Fix the perf event cgroup tracking which tries to track the cgroup even
for disabled events.
- Add Ice Lake server support for uncore events
- Disable pagefaults when retrieving the physical address in the sampling
code.
-----BEGIN PGP SIGNATURE-----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=5kqD
-----END PGP SIGNATURE-----
Merge tag 'perf-urgent-2020-04-12' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull perf fixes from Thomas Gleixner:
"Three fixes/updates for perf:
- Fix the perf event cgroup tracking which tries to track the cgroup
even for disabled events.
- Add Ice Lake server support for uncore events
- Disable pagefaults when retrieving the physical address in the
sampling code"
* tag 'perf-urgent-2020-04-12' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
perf/core: Disable page faults when getting phys address
perf/x86/intel/uncore: Add Ice Lake server uncore support
perf/cgroup: Correct indirection in perf_less_group_idx()
perf/core: Fix event cgroup tracking
- Plug a task struct reference leak in the percpu rswem implementation.
- Document the refcount interaction with PID_MAX_LIMIT
- Improve the 'invalid wait context' data dump in lockdep so it contains
all information which is required to decode the problem
-----BEGIN PGP SIGNATURE-----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=Agrh
-----END PGP SIGNATURE-----
Merge tag 'locking-urgent-2020-04-12' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull locking fixes from Thomas Gleixner:
"Three small fixes/updates for the locking core code:
- Plug a task struct reference leak in the percpu rswem
implementation.
- Document the refcount interaction with PID_MAX_LIMIT
- Improve the 'invalid wait context' data dump in lockdep so it
contains all information which is required to decode the problem"
* tag 'locking-urgent-2020-04-12' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
locking/lockdep: Improve 'invalid wait context' splat
locking/refcount: Document interaction with PID_MAX_LIMIT
locking/percpu-rwsem: Fix a task_struct refcount
-----BEGIN PGP SIGNATURE-----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=tstz
-----END PGP SIGNATURE-----
Merge tag '5.7-rc-smb3-fixes-part2' of git://git.samba.org/sfrench/cifs-2.6
Pull cifs fixes from Steve French:
"Ten cifs/smb fixes:
- five RDMA (smbdirect) related fixes
- add experimental support for swap over SMB3 mounts
- also a fix which improves performance of signed connections"
* tag '5.7-rc-smb3-fixes-part2' of git://git.samba.org/sfrench/cifs-2.6:
smb3: enable swap on SMB3 mounts
smb3: change noisy error message to FYI
smb3: smbdirect support can be configured by default
cifs: smbd: Do not schedule work to send immediate packet on every receive
cifs: smbd: Properly process errors on ib_post_send
cifs: Allocate crypto structures on the fly for calculating signatures of incoming packets
cifs: smbd: Update receive credits before sending and deal with credits roll back on failure before sending
cifs: smbd: Check send queue size before posting a send
cifs: smbd: Merge code to track pending packets
cifs: ignore cached share root handle closing errors
- fix an integer truncation in dma_direct_get_required_mask
(Kishon Vijay Abraham)
- fix the display of dma mapping types (Grygorii Strashko)
-----BEGIN PGP SIGNATURE-----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=Af93
-----END PGP SIGNATURE-----
Merge tag 'dma-mapping-5.7-1' of git://git.infradead.org/users/hch/dma-mapping
Pull dma-mapping fixes from Christoph Hellwig:
- fix an integer truncation in dma_direct_get_required_mask
(Kishon Vijay Abraham)
- fix the display of dma mapping types (Grygorii Strashko)
* tag 'dma-mapping-5.7-1' of git://git.infradead.org/users/hch/dma-mapping:
dma-debug: fix displaying of dma allocation type
dma-direct: fix data truncation in dma_direct_get_required_mask()
- raise minimum supported binutils version to 2.23
- remove old CONFIG_AS_* macros that we know binutils >= 2.23 supports
- move remaining CONFIG_AS_* tests to Kconfig from Makefile
- enable -Wtautological-compare warnings to catch more issues
- do not support GCC plugins for GCC <= 4.7
- fix various breakages of 'make xconfig'
- include the linker version used for linking the kernel into
LINUX_COMPILER, which is used for the banner, and also exposed to
/proc/version
- link lib-y objects to vmlinux forcibly when CONFIG_MODULES=y,
which allows us to remove the lib-ksyms.o workaround, and to
solve the last known issue of the LLVM linker
- add dummy tools in scripts/dummy-tools/ to enable all compiler
tests in Kconfig, which will be useful for distro maintainers
- support the single switch, LLVM=1 to use Clang and all LLVM utilities
instead of GCC and Binutils.
- support LLVM_IAS=1 to enable the integrated assembler, which is still
experimental
-----BEGIN PGP SIGNATURE-----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=jpyF
-----END PGP SIGNATURE-----
Merge tag 'kbuild-v5.7-2' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild
Pull more Kbuild updates from Masahiro Yamada:
- raise minimum supported binutils version to 2.23
- remove old CONFIG_AS_* macros that we know binutils >= 2.23 supports
- move remaining CONFIG_AS_* tests to Kconfig from Makefile
- enable -Wtautological-compare warnings to catch more issues
- do not support GCC plugins for GCC <= 4.7
- fix various breakages of 'make xconfig'
- include the linker version used for linking the kernel into
LINUX_COMPILER, which is used for the banner, and also exposed to
/proc/version
- link lib-y objects to vmlinux forcibly when CONFIG_MODULES=y, which
allows us to remove the lib-ksyms.o workaround, and to solve the last
known issue of the LLVM linker
- add dummy tools in scripts/dummy-tools/ to enable all compiler tests
in Kconfig, which will be useful for distro maintainers
- support the single switch, LLVM=1 to use Clang and all LLVM utilities
instead of GCC and Binutils.
- support LLVM_IAS=1 to enable the integrated assembler, which is still
experimental
* tag 'kbuild-v5.7-2' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild: (36 commits)
kbuild: fix comment about missing include guard detection
kbuild: support LLVM=1 to switch the default tools to Clang/LLVM
kbuild: replace AS=clang with LLVM_IAS=1
kbuild: add dummy toolchains to enable all cc-option etc. in Kconfig
kbuild: link lib-y objects to vmlinux forcibly when CONFIG_MODULES=y
MIPS: fw: arc: add __weak to prom_meminit and prom_free_prom_memory
kbuild: remove -I$(srctree)/tools/include from scripts/Makefile
kbuild: do not pass $(KBUILD_CFLAGS) to scripts/mkcompile_h
Documentation/llvm: fix the name of llvm-size
kbuild: mkcompile_h: Include $LD version in /proc/version
kconfig: qconf: Fix a few alignment issues
kconfig: qconf: remove some old bogus TODOs
kconfig: qconf: fix support for the split view mode
kconfig: qconf: fix the content of the main widget
kconfig: qconf: Change title for the item window
kconfig: qconf: clean deprecated warnings
gcc-plugins: drop support for GCC <= 4.7
kbuild: Enable -Wtautological-compare
x86: update AS_* macros to binutils >=2.23, supporting ADX and AVX2
crypto: x86 - clean up poly1305-x86_64-cryptogams.S by 'make clean'
...
I do not longer work for credativ Germany.
Please, use my private email address instead.
This is for the case when people want to CC me on
patches sent from my old business email address.
Signed-off-by: Sedat Dilek <sedat.dilek@gmail.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Another brown paper bag moment. pnfs_alloc_ds_commits_list() is leaking
the RCU lock.
Fixes: a9901899b6 ("pNFS: Add infrastructure for cleaning up per-layout commit structures")
Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com>
Two types of #AC can be generated in Intel CPUs:
1. legacy alignment check #AC
2. split lock #AC
Reflect #AC back into the guest if the guest has legacy alignment checks
enabled or if split lock detection is disabled.
If the #AC is not a legacy one and split lock detection is enabled, then
invoke handle_guest_split_lock() which will either warn and disable split
lock detection for this task or force SIGBUS on it.
[ tglx: Switch it to handle_guest_split_lock() and rename the misnamed
helper function. ]
Suggested-by: Sean Christopherson <sean.j.christopherson@intel.com>
Signed-off-by: Xiaoyao Li <xiaoyao.li@intel.com>
Signed-off-by: Sean Christopherson <sean.j.christopherson@intel.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Borislav Petkov <bp@suse.de>
Acked-by: Paolo Bonzini <pbonzini@redhat.com>
Link: https://lkml.kernel.org/r/20200410115517.176308876@linutronix.de
Without at least minimal handling for split lock detection induced #AC,
VMX will just run into the same problem as the VMWare hypervisor, which
was reported by Kenneth.
It will inject the #AC blindly into the guest whether the guest is
prepared or not.
Provide a function for guest mode which acts depending on the host
SLD mode. If mode == sld_warn, treat it like user space, i.e. emit a
warning, disable SLD and mark the task accordingly. Otherwise force
SIGBUS.
[ bp: Add a !CPU_SUP_INTEL stub for handle_guest_split_lock(). ]
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Borislav Petkov <bp@suse.de>
Acked-by: Paolo Bonzini <pbonzini@redhat.com>
Link: https://lkml.kernel.org/r/20200410115516.978037132@linutronix.de
Link: https://lkml.kernel.org/r/20200402123258.895628824@linutronix.de
