commit a8eda9fa1b upstream.
There is a bug in the current GPIO code for ftdi_sio: it failed to take USB
autosuspend into account. If the device is in autosuspend, calls to
usb_control_msg() fail with -EHOSTUNREACH. Because the standard value for
autosuspend timeout is usually 2-5 seconds, this made it almost impossible
to use the GPIOs on machines that have USB autosuspend enabled. This patch
fixes the issue by acquiring a PM lock on the device for the duration of
the USB transfers. Tested on an FT231X device.
Signed-off-by: Karoly Pados <pados@pados.hu>
[ johan: simplify code somewhat ]
Fixes: ba93cc7da8 ("USB: serial: ftdi_sio: implement GPIO support for FT-X devices")
Cc: stable <stable@vger.kernel.org> # 4.20
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 91f7d2e898 upstream.
The patch "usb: simplify usbport trigger" together with "leds: triggers:
add device attribute support" caused an regression for the usbport
trigger. it will no longer enumerate any active usb hub ports under the
"ports" directory in the sysfs class directory, if the usb host drivers
are fully initialized before the usbport trigger was loaded.
The reason is that the usbport driver tries to register the sysfs
entries during the activate() callback. And this will fail with -2 /
ENOENT because the patch "leds: triggers: add device attribute support"
made it so that the sysfs "ports" group was only being added after the
activate() callback succeeded.
This version of the patch reverts parts of the "usb: simplify usbport
trigger" patch and restores usbport trigger's functionality.
Fixes: 6f7b0bad88 ("usb: simplify usbport trigger")
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Cc: stable <stable@vger.kernel.org>
Acked-by: Jacek Anaszewski <jacek.anaszewski@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit deaa5c96c2 ]
When using Kerberos with v4.20, I've observed frequent connection
loss on heavy workloads. I traced it down to the client underrunning
the GSS sequence number window -- NFS servers are required to drop
the RPC with the low sequence number, and also drop the connection
to signal that an RPC was dropped.
Bisected to commit 918f3c1fe8 ("SUNRPC: Improve latency for
interactive tasks").
I've got a one-line workaround for this issue, which is easy to
backport to v4.20 while a more permanent solution is being derived.
Essentially, tk_owner-based sorting is disabled for RPCs that carry
a GSS sequence number.
Fixes: 918f3c1fe8 ("SUNRPC: Improve latency for interactive ... ")
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit d6951f582c upstream.
The intention in the previous patch was to only place the processor
tables in the .rodata section if big.Little was being built and we
wanted the branch target hardening, but instead (due to the way it
was tested) it ended up always placing the tables into the .rodata
section.
Although harmless, let's correct this anyway.
Fixes: 3a4d0c2172 ("ARM: ensure that processor vtables is not lost after boot")
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David A. Long <dave.long@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 13d7f46386 ]
TCP transmission with MSG_ZEROCOPY fails if the peer closes its end of
the connection and so transitions this socket to CLOSE_WAIT state.
Transmission in close wait state is acceptable. Other similar tests in
the stack (e.g., in FastOpen) accept both states. Relax this test, too.
Link: https://www.mail-archive.com/netdev@vger.kernel.org/msg276886.html
Link: https://www.mail-archive.com/netdev@vger.kernel.org/msg227390.html
Fixes: f214f915e7 ("tcp: enable MSG_ZEROCOPY")
Reported-by: Marek Majkowski <marek@cloudflare.com>
Signed-off-by: Willem de Bruijn <willemb@google.com>
CC: Yuchung Cheng <ycheng@google.com>
CC: Neal Cardwell <ncardwell@google.com>
CC: Soheil Hassas Yeganeh <soheil@google.com>
CC: Alexey Kodanev <alexey.kodanev@oracle.com>
Acked-by: Soheil Hassas Yeganeh <soheil@google.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 80b3671e93 ]
We forgot to update ip6erspan version related info when changing link,
which will cause setting new hwid failed.
Reported-by: Jianlin Shi <jishi@redhat.com>
Fixes: 94d7d8f292 ("ip6_gre: add erspan v2 support")
Signed-off-by: Hangbin Liu <liuhangbin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit e0a7328fad ]
m88e1318_set_wol() takes the lock as part of phy_select_page(). Don't
take the lock again with phy_read(), use the unlocked __phy_read().
Fixes: 424ca4c551 ("net: phy: marvell: fix paged access races")
Reported-by: Åke Rehnman <ake.rehnman@gmail.com>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 20704bd163 ]
As said in draft-foschiano-erspan-03#section4:
Different frame variants known as "ERSPAN Types" can be
distinguished based on the GRE "Protocol Type" field value: Type I
and II's value is 0x88BE while Type III's is 0x22EB [ETYPES].
So set it properly in erspan_xmit() according to erspan_ver. While at
it, also remove the unused parameter 'proto' in erspan_fb_xmit().
Fixes: 94d7d8f292 ("ip6_gre: add erspan v2 support")
Reported-by: Jianlin Shi <jishi@redhat.com>
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit ab5098fa25 ]
In changelink ops, the ip6gre_net pointer is retrieved from
dev_net(dev), which is wrong in case of x-netns. Thus, the tunnel is not
unlinked from its current list and is relinked into another net
namespace. This corrupts the tunnel lists and can later trigger a kernel
oops.
Fix this by retrieving the netns from device private area.
Fixes: c8632fc30b ("net: ip6_gre: Split up ip6gre_changelink()")
Cc: Petr Machata <petrm@mellanox.com>
Signed-off-by: Olivier Matz <olivier.matz@6wind.com>
Acked-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 0f149c9fec ]
Failure __ip_append_data triggers udp_flush_pending_frames, but these
tests happen later. The skb must be freed directly.
Fixes: bec1f6f697 ("udp: generate gso with UDP_SEGMENT")
Reported-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 2cddd20147 ]
Recent changes (especially 05cd271fd6 ("cls_flower: Support multiple
masks per priority")) in the fl_flow_mask structure grow it and its
current size e.g. on x86_64 with defconfig is 760 bytes and more than
1024 bytes with some debug options enabled. Prior the mentioned commit
its size was 176 bytes (using defconfig on x86_64).
With regard to this fact it's reasonable to allocate this structure
dynamically in fl_change() to reduce its stack size.
v2:
- use kzalloc() instead of kcalloc()
Fixes: 05cd271fd6 ("cls_flower: Support multiple masks per priority")
Cc: Jiri Pirko <jiri@resnulli.us>
Cc: Paul Blakey <paulb@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ivan Vecera <ivecera@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When a packet should be trapped to the CPU the device consumes a WQE
(work queue element) from an RDQ (receive descriptor queue) and copies
the packet to the address specified in the WQE. The device then tries to
post a CQE (completion queue element) that contains various metadata
(e.g., ingress port) about the packet to a CQ (completion queue).
In case the device managed to consume a WQE, but did not manage to post
the corresponding CQE, it will get stuck. This unlikely situation can be
triggered due to the scheme the driver is currently using to process
CQEs.
The driver will consume up to 512 CQEs at a time and after processing
each corresponding WQE it will ring the RDQ's doorbell, letting the
device know that a new WQE was posted for it to consume. Only after
processing all the CQEs (up to 512), the driver will ring the CQ's
doorbell, letting the device know that new ones can be posted.
Fix this by having the driver ring the CQ's doorbell for every processed
CQE, but before ringing the RDQ's doorbell. This guarantees that
whenever we post a new WQE, there is a corresponding CQE available. Copy
the currently processed CQE to prevent the device from overwriting it
with a new CQE after ringing the doorbell.
Note that the driver still arms the CQ only after processing all the
pending CQEs, so that interrupts for this CQ will only be delivered
after the driver finished its processing.
Before commit 8404f6f2e8 ("mlxsw: pci: Allow to use CQEs of version 1
and version 2") the issue was virtually impossible to trigger since the
number of CQEs was twice the number of WQEs and the number of CQEs
processed at a time was equal to the number of available WQEs.
Fixes: 8404f6f2e8 ("mlxsw: pci: Allow to use CQEs of version 1 and version 2")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reported-by: Semion Lisyansky <semionl@mellanox.com>
Tested-by: Semion Lisyansky <semionl@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit a11dcd6497 ]
When using a tc flower action of egress mirred redirect, the driver adds
an implicit FID setting action. This implicit action sets a dummy FID to
the packet and is used as part of a design for trapping unmatched flows
in OVS. While this implicit FID setting action is supposed to be a NOP
when a redirect action is added, in Spectrum-2 the FID record is
consulted as the dummy FID index is an 802.1D FID index and the packet
is dropped instead of being redirected.
Set the dummy FID index value to be within 802.1Q range. This satisfies
both Spectrum-1 which ignores the FID and Spectrum-2 which identifies it
as an 802.1Q FID and will then follow the redirect action.
Fixes: c3ab435466 ("mlxsw: spectrum: Extend to support Spectrum-2 ASIC")
Signed-off-by: Nir Dotan <nird@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit f97f4dd8b3 ]
IPv4 routing tables are flushed in two cases:
1. In response to events in the netdev and inetaddr notification chains
2. When a network namespace is being dismantled
In both cases only routes associated with a dead nexthop group are
flushed. However, a nexthop group will only be marked as dead in case it
is populated with actual nexthops using a nexthop device. This is not
the case when the route in question is an error route (e.g.,
'blackhole', 'unreachable').
Therefore, when a network namespace is being dismantled such routes are
not flushed and leaked [1].
To reproduce:
# ip netns add blue
# ip -n blue route add unreachable 192.0.2.0/24
# ip netns del blue
Fix this by not skipping error routes that are not marked with
RTNH_F_DEAD when flushing the routing tables.
To prevent the flushing of such routes in case #1, add a parameter to
fib_table_flush() that indicates if the table is flushed as part of
namespace dismantle or not.
Note that this problem does not exist in IPv6 since error routes are
associated with the loopback device.
[1]
unreferenced object 0xffff888066650338 (size 56):
comm "ip", pid 1206, jiffies 4294786063 (age 26.235s)
hex dump (first 32 bytes):
00 00 00 00 00 00 00 00 b0 1c 62 61 80 88 ff ff ..........ba....
e8 8b a1 64 80 88 ff ff 00 07 00 08 fe 00 00 00 ...d............
backtrace:
[<00000000856ed27d>] inet_rtm_newroute+0x129/0x220
[<00000000fcdfc00a>] rtnetlink_rcv_msg+0x397/0xa20
[<00000000cb85801a>] netlink_rcv_skb+0x132/0x380
[<00000000ebc991d2>] netlink_unicast+0x4c0/0x690
[<0000000014f62875>] netlink_sendmsg+0x929/0xe10
[<00000000bac9d967>] sock_sendmsg+0xc8/0x110
[<00000000223e6485>] ___sys_sendmsg+0x77a/0x8f0
[<000000002e94f880>] __sys_sendmsg+0xf7/0x250
[<00000000ccb1fa72>] do_syscall_64+0x14d/0x610
[<00000000ffbe3dae>] entry_SYSCALL_64_after_hwframe+0x49/0xbe
[<000000003a8b605b>] 0xffffffffffffffff
unreferenced object 0xffff888061621c88 (size 48):
comm "ip", pid 1206, jiffies 4294786063 (age 26.235s)
hex dump (first 32 bytes):
6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b kkkkkkkkkkkkkkkk
6b 6b 6b 6b 6b 6b 6b 6b d8 8e 26 5f 80 88 ff ff kkkkkkkk..&_....
backtrace:
[<00000000733609e3>] fib_table_insert+0x978/0x1500
[<00000000856ed27d>] inet_rtm_newroute+0x129/0x220
[<00000000fcdfc00a>] rtnetlink_rcv_msg+0x397/0xa20
[<00000000cb85801a>] netlink_rcv_skb+0x132/0x380
[<00000000ebc991d2>] netlink_unicast+0x4c0/0x690
[<0000000014f62875>] netlink_sendmsg+0x929/0xe10
[<00000000bac9d967>] sock_sendmsg+0xc8/0x110
[<00000000223e6485>] ___sys_sendmsg+0x77a/0x8f0
[<000000002e94f880>] __sys_sendmsg+0xf7/0x250
[<00000000ccb1fa72>] do_syscall_64+0x14d/0x610
[<00000000ffbe3dae>] entry_SYSCALL_64_after_hwframe+0x49/0xbe
[<000000003a8b605b>] 0xffffffffffffffff
Fixes: 8cced9eff1 ("[NETNS]: Enable routing configuration in non-initial namespace.")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit d2f372ba09 ]
Spectrum-2 PHY layer introduces a calibration period which is a part of the
Spectrum-2 firmware boot process. Hence increase the SW timeout waiting for
the firmware to come out of boot. This does not increase system boot time
in cases where the firmware PHY calibration process is done quickly.
Fixes: c3ab435466 ("mlxsw: spectrum: Extend to support Spectrum-2 ASIC")
Signed-off-by: Nir Dotan <nird@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit cc5e710759 ]
Vhost dirty page logging API is designed to sync through GPA. But we
try to log GIOVA when device IOTLB is enabled. This is wrong and may
lead to missing data after migration.
To solve this issue, when logging with device IOTLB enabled, we will:
1) reuse the device IOTLB translation result of GIOVA->HVA mapping to
get HVA, for writable descriptor, get HVA through iovec. For used
ring update, translate its GIOVA to HVA
2) traverse the GPA->HVA mapping to get the possible GPA and log
through GPA. Pay attention this reverse mapping is not guaranteed
to be unique, so we should log each possible GPA in this case.
This fix the failure of scp to guest during migration. In -next, we
will probably support passing GIOVA->GPA instead of GIOVA->HVA.
Fixes: 6b1e6cc785 ("vhost: new device IOTLB API")
Reported-by: Jintack Lim <jintack@cs.columbia.edu>
Cc: Jintack Lim <jintack@cs.columbia.edu>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 04a4af334b ]
For nested and variable attributes, the expected length of an attribute
is not known and marked by a negative number. This results in an OOB
read when the expected length is later used to check if the attribute is
all zeros. Fix this by using the actual length of the attribute rather
than the expected length.
Signed-off-by: Ross Lagerwall <ross.lagerwall@citrix.com>
Acked-by: Pravin B Shelar <pshelar@ovn.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit cd0c4e70fc ]
Martin reported a set of filters don't work after changing
from reclassify to continue. Looking into the code, it
looks like skb protocol is not always fetched for each
iteration of the filters. But, as demonstrated by Martin,
TC actions could modify skb->protocol, for example act_vlan,
this means we have to refetch skb protocol in each iteration,
rather than using the one we fetch in the beginning of the loop.
This bug is _not_ introduced by commit 3b3ae88026
("net: sched: consolidate tc_classify{,_compat}"), technically,
if act_vlan is the only action that modifies skb protocol, then
it is commit c7e2b9689e ("sched: introduce vlan action") which
introduced this bug.
Reported-by: Martin Olsson <martin.olsson+netdev@sentorsecurity.com>
Cc: Jamal Hadi Salim <jhs@mojatatu.com>
Cc: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 3e64cf7a43 ]
Since phy driver features became a link_mode bitmap, phy drivers that
don't have a list of features configured will cause the kernel to crash
when probed.
Prevent the phy driver from registering if the features field is missing.
Fixes: 719655a149 ("net: phy: Replace phy driver features u32 with link_mode bitmap")
Reported-by: Scott Wood <oss@buserror.net>
Signed-off-by: Camelia Groza <camelia.groza@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 8cbcdc1a51 ]
The VOD can be out of spec, unless some magic value is poked into an
undocumented register in an undocumented page.
Fixes: e4cf8a38fc ("net: phy: Marvell: Add mv88e6390 internal PHY")
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 6c57f04580 ]
In certain cases, pskb_trim_rcsum() may change skb pointers.
Reinitialize header pointers afterwards to avoid potential
use-after-frees. Add a note in the documentation of
pskb_trim_rcsum(). Found by KASAN.
Signed-off-by: Ross Lagerwall <ross.lagerwall@citrix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 28c1382fa2 ]
The skb header should be set to ethernet header before using
is_skb_forwardable. Because the ethernet header length has been
considered in is_skb_forwardable(including dev->hard_header_len
length).
To reproduce the issue:
1, add 2 ports on linux bridge br using following commands:
$ brctl addbr br
$ brctl addif br eth0
$ brctl addif br eth1
2, the MTU of eth0 and eth1 is 1500
3, send a packet(Data 1480, UDP 8, IP 20, Ethernet 14, VLAN 4)
from eth0 to eth1
So the expect result is packet larger than 1500 cannot pass through
eth0 and eth1. But currently, the packet passes through success, it
means eth1's MTU limit doesn't take effect.
Fixes: f6367b4660 ("bridge: use is_skb_forwardable in forward path")
Cc: bridge@lists.linux-foundation.org
Cc: Nkolay Aleksandrov <nikolay@cumulusnetworks.com>
Cc: Roopa Prabhu <roopa@cumulusnetworks.com>
Cc: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: Yunjian Wang <wangyunjian@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 5ab3121bee ]
The XGBE hardware has support for performing MDIO operations using an
MDIO command request. The driver mistakenly uses the mdio port address
as the MDIO command request device address instead of the MDIO command
request port address. Additionally, the driver does not properly check
for and create a clause 45 MDIO command.
Check the supplied MDIO register to determine if the request is a clause
45 operation (MII_ADDR_C45). For a clause 45 operation, extract the device
address and register number from the supplied MDIO register and use them
to set the MDIO command request device address and register number fields.
For a clause 22 operation, the MDIO request device address is set to zero
and the MDIO command request register number is set to the supplied MDIO
register. In either case, the supplied MDIO port address is used as the
MDIO command request port address.
Fixes: 732f2ab7af ("amd-xgbe: Add support for MDIO attached PHYs")
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Tested-by: Shyam Sundar S K <Shyam-sundar.S-k@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7d6380cd40 upstream.
The block number was not being compared right, it was off by one
when checking the response.
Some statistics wouldn't be incremented properly in some cases.
Check to see if that middle-part messages always have 31 bytes of
data.
Signed-off-by: Corey Minyard <cminyard@mvista.com>
Cc: stable@vger.kernel.org # 4.4
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 479d6b39b9 upstream.
Some IPMI modules (e.g. ibmpex_msg_handler()) will have ipmi_usr_hdlr
handlers that call ipmi_free_recv_msg() directly. This will essentially
kfree(msg), leading to use-after-free.
This does not happen in the ipmi_devintf module, which will queue the
message and run ipmi_free_recv_msg() later.
BUG: KASAN: use-after-free in deliver_response+0x12f/0x1b0
Read of size 8 at addr ffff888a7bf20018 by task ksoftirqd/3/27
CPU: 3 PID: 27 Comm: ksoftirqd/3 Tainted: G O 4.19.11-amd64-ani99-debug #12.0.1.601133+pv
Hardware name: AppNeta r1000/X11SPW-TF, BIOS 2.1a-AP 09/17/2018
Call Trace:
dump_stack+0x92/0xeb
print_address_description+0x73/0x290
kasan_report+0x258/0x380
deliver_response+0x12f/0x1b0
? ipmi_free_recv_msg+0x50/0x50
deliver_local_response+0xe/0x50
handle_one_recv_msg+0x37a/0x21d0
handle_new_recv_msgs+0x1ce/0x440
...
Allocated by task 9885:
kasan_kmalloc+0xa0/0xd0
kmem_cache_alloc_trace+0x116/0x290
ipmi_alloc_recv_msg+0x28/0x70
i_ipmi_request+0xb4a/0x1640
ipmi_request_settime+0x1b8/0x1e0
...
Freed by task 27:
__kasan_slab_free+0x12e/0x180
kfree+0xe9/0x280
deliver_response+0x122/0x1b0
deliver_local_response+0xe/0x50
handle_one_recv_msg+0x37a/0x21d0
handle_new_recv_msgs+0x1ce/0x440
tasklet_action_common.isra.19+0xc4/0x250
__do_softirq+0x11f/0x51f
Fixes: e86ee2d44b ("ipmi: Rework locking and shutdown for hot remove")
Cc: stable@vger.kernel.org # 4.18
Signed-off-by: Fred Klassen <fklassen@appneta.com>
Signed-off-by: Corey Minyard <cminyard@mvista.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a7102c7461 upstream.
channel and addr->channel are indirectly controlled by user-space,
hence leading to a potential exploitation of the Spectre variant 1
vulnerability.
These issues were detected with the help of Smatch:
drivers/char/ipmi/ipmi_msghandler.c:1381 ipmi_set_my_address() warn: potential spectre issue 'user->intf->addrinfo' [w] (local cap)
drivers/char/ipmi/ipmi_msghandler.c:1401 ipmi_get_my_address() warn: potential spectre issue 'user->intf->addrinfo' [r] (local cap)
drivers/char/ipmi/ipmi_msghandler.c:1421 ipmi_set_my_LUN() warn: potential spectre issue 'user->intf->addrinfo' [w] (local cap)
drivers/char/ipmi/ipmi_msghandler.c:1441 ipmi_get_my_LUN() warn: potential spectre issue 'user->intf->addrinfo' [r] (local cap)
drivers/char/ipmi/ipmi_msghandler.c:2260 check_addr() warn: potential spectre issue 'intf->addrinfo' [r] (local cap)
Fix this by sanitizing channel and addr->channel before using them to
index user->intf->addrinfo and intf->addrinfo, correspondingly.
Notice that given that speculation windows are large, the policy is
to kill the speculation on the first load and not worry if it can be
completed with a dependent load/store [1].
[1] https://lore.kernel.org/lkml/20180423164740.GY17484@dhcp22.suse.cz/
Cc: stable@vger.kernel.org
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Corey Minyard <cminyard@mvista.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 913a89f009 upstream.
The IPMI driver was recently modified to use SRCU, but it turns out
this uses a chunk of percpu memory, even if IPMI is never used.
So modify thing to on initialize on the first use. There was already
code to sort of handle this for handling init races, so piggy back
on top of that, and simplify it in the process.
Signed-off-by: Corey Minyard <cminyard@mvista.com>
Reported-by: Tejun Heo <tj@kernel.org>
Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Reviewed-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: stable@vger.kernel.org # 4.18
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1629db9c75 upstream.
In case a command which completes in Command Status was sent using the
hci_cmd_send-family of APIs there would be a misleading error in the
hci_get_cmd_complete function, since the code would be trying to fetch
the Command Complete parameters when there are none.
Avoid the misleading error and silently bail out from the function in
case the received event is a command status.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Acked-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Tested-by Adam Ford <aford173@gmail.com> #4.19.16
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ae1cf20df7 upstream.
[Why]
The cursor vanishes when touching the top of edge of the screen for
Raven on Linux.
This occurs because the cursor height is not taken into account when
deciding to disable the cursor.
[How]
Factor in the cursor height into the cursor calculations - and mimic
the existing x position calculations.
Fixes: 94a4ffd1d4 ("drm/amd/display: fix PIP bugs on Dal3")
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Harry Wentland <Harry.Wentland@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit fed84c7852 ]
Kmemleak does not play well with KASAN (tested on both HPE Apollo 70 and
Huawei TaiShan 2280 aarch64 servers).
After calling start_kernel()->setup_arch()->kasan_init(), kmemleak early
log buffer went from something like 280 to 260000 which caused kmemleak
disabled and crash dump memory reservation failed. The multitude of
kmemleak_alloc() calls is from nested loops while KASAN is setting up full
memory mappings, so let early kmemleak allocations skip those
memblock_alloc_internal() calls came from kasan_init() given that those
early KASAN memory mappings should not reference to other memory. Hence,
no kmemleak false positives.
kasan_init
kasan_map_populate [1]
kasan_pgd_populate [2]
kasan_pud_populate [3]
kasan_pmd_populate [4]
kasan_pte_populate [5]
kasan_alloc_zeroed_page
memblock_alloc_try_nid
memblock_alloc_internal
kmemleak_alloc
[1] for_each_memblock(memory, reg)
[2] while (pgdp++, addr = next, addr != end)
[3] while (pudp++, addr = next, addr != end && pud_none(READ_ONCE(*pudp)))
[4] while (pmdp++, addr = next, addr != end && pmd_none(READ_ONCE(*pmdp)))
[5] while (ptep++, addr = next, addr != end && pte_none(READ_ONCE(*ptep)))
Link: http://lkml.kernel.org/r/1543442925-17794-1-git-send-email-cai@gmx.us
Signed-off-by: Qian Cai <cai@gmx.us>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Cc: Michal Hocko <mhocko@suse.com>
Cc: Mike Rapoport <rppt@linux.vnet.ibm.com>
Cc: Alexander Potapenko <glider@google.com>
Cc: Dmitry Vyukov <dvyukov@google.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7550c60798 ]
Patch series "THP eligibility reporting via proc".
This series of three patches aims at making THP eligibility reporting much
more robust and long term sustainable. The trigger for the change is a
regression report [2] and the long follow up discussion. In short the
specific application didn't have good API to query whether a particular
mapping can be backed by THP so it has used VMA flags to workaround that.
These flags represent a deep internal state of VMAs and as such they
should be used by userspace with a great deal of caution.
A similar has happened for [3] when users complained that VM_MIXEDMAP is
no longer set on DAX mappings. Again a lack of a proper API led to an
abuse.
The first patch in the series tries to emphasise that that the semantic of
flags might change and any application consuming those should be really
careful.
The remaining two patches provide a more suitable interface to address [2]
and provide a consistent API to query the THP status both for each VMA and
process wide as well. [1]
http://lkml.kernel.org/r/20181120103515.25280-1-mhocko@kernel.org [2]
http://lkml.kernel.org/r/http://lkml.kernel.org/r/alpine.DEB.2.21.1809241054050.224429@chino.kir.corp.google.com
[3] http://lkml.kernel.org/r/20181002100531.GC4135@quack2.suse.cz
This patch (of 3):
Even though vma flags exported via /proc/<pid>/smaps are explicitly
documented to be not guaranteed for future compatibility the warning
doesn't go far enough because it doesn't mention semantic changes to those
flags. And they are important as well because these flags are a deep
implementation internal to the MM code and the semantic might change at
any time.
Let's consider two recent examples:
http://lkml.kernel.org/r/20181002100531.GC4135@quack2.suse.cz
: commit e1fb4a0864 "dax: remove VM_MIXEDMAP for fsdax and device dax" has
: removed VM_MIXEDMAP flag from DAX VMAs. Now our testing shows that in the
: mean time certain customer of ours started poking into /proc/<pid>/smaps
: and looks at VMA flags there and if VM_MIXEDMAP is missing among the VMA
: flags, the application just fails to start complaining that DAX support is
: missing in the kernel.
http://lkml.kernel.org/r/alpine.DEB.2.21.1809241054050.224429@chino.kir.corp.google.com
: Commit 1860033237 ("mm: make PR_SET_THP_DISABLE immediately active")
: introduced a regression in that userspace cannot always determine the set
: of vmas where thp is ineligible.
: Userspace relies on the "nh" flag being emitted as part of /proc/pid/smaps
: to determine if a vma is eligible to be backed by hugepages.
: Previous to this commit, prctl(PR_SET_THP_DISABLE, 1) would cause thp to
: be disabled and emit "nh" as a flag for the corresponding vmas as part of
: /proc/pid/smaps. After the commit, thp is disabled by means of an mm
: flag and "nh" is not emitted.
: This causes smaps parsing libraries to assume a vma is eligible for thp
: and ends up puzzling the user on why its memory is not backed by thp.
In both cases userspace was relying on a semantic of a specific VMA flag.
The primary reason why that happened is a lack of a proper interface.
While this has been worked on and it will be fixed properly, it seems that
our wording could see some refinement and be more vocal about semantic
aspect of these flags as well.
Link: http://lkml.kernel.org/r/20181211143641.3503-2-mhocko@kernel.org
Signed-off-by: Michal Hocko <mhocko@suse.com>
Acked-by: Jan Kara <jack@suse.cz>
Acked-by: Dan Williams <dan.j.williams@intel.com>
Acked-by: David Rientjes <rientjes@google.com>
Acked-by: Mike Rapoport <rppt@linux.ibm.com>
Acked-by: Vlastimil Babka <vbabka@suse.cz>
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: David Rientjes <rientjes@google.com>
Cc: Paul Oppenheimer <bepvte@gmail.com>
Cc: William Kucharski <william.kucharski@oracle.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3cfd22be0a ]
When the process being tracked does mremap() without
UFFD_FEATURE_EVENT_REMAP on the corresponding tracking uffd file handle,
we should not generate the remap event, and at the same time we should
clear all the uffd flags on the new VMA. Without this patch, we can still
have the VM_UFFD_MISSING|VM_UFFD_WP flags on the new VMA even the fault
handling process does not even know the existance of the VMA.
Link: http://lkml.kernel.org/r/20181211053409.20317-1-peterx@redhat.com
Signed-off-by: Peter Xu <peterx@redhat.com>
Reviewed-by: Andrea Arcangeli <aarcange@redhat.com>
Acked-by: Mike Rapoport <rppt@linux.vnet.ibm.com>
Reviewed-by: William Kucharski <william.kucharski@oracle.com>
Cc: Andrea Arcangeli <aarcange@redhat.com>
Cc: Mike Rapoport <rppt@linux.vnet.ibm.com>
Cc: Kirill A. Shutemov <kirill@shutemov.name>
Cc: Hugh Dickins <hughd@google.com>
Cc: Pavel Emelyanov <xemul@virtuozzo.com>
Cc: Pravin Shedge <pravin.shedge4linux@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 66f71da9dd ]
Since a2468cc9bf ("swap: choose swap device according to numa node"),
avail_lists field of swap_info_struct is changed to an array with
MAX_NUMNODES elements. This made swap_info_struct size increased to 40KiB
and needs an order-4 page to hold it.
This is not optimal in that:
1 Most systems have way less than MAX_NUMNODES(1024) nodes so it
is a waste of memory;
2 It could cause swapon failure if the swap device is swapped on
after system has been running for a while, due to no order-4
page is available as pointed out by Vasily Averin.
Solve the above two issues by using nr_node_ids(which is the actual
possible node number the running system has) for avail_lists instead of
MAX_NUMNODES.
nr_node_ids is unknown at compile time so can't be directly used when
declaring this array. What I did here is to declare avail_lists as zero
element array and allocate space for it when allocating space for
swap_info_struct. The reason why keep using array but not pointer is
plist_for_each_entry needs the field to be part of the struct, so pointer
will not work.
This patch is on top of Vasily Averin's fix commit. I think the use of
kvzalloc for swap_info_struct is still needed in case nr_node_ids is
really big on some systems.
Link: http://lkml.kernel.org/r/20181115083847.GA11129@intel.com
Signed-off-by: Aaron Lu <aaron.lu@intel.com>
Reviewed-by: Andrew Morton <akpm@linux-foundation.org>
Acked-by: Michal Hocko <mhocko@suse.com>
Cc: Vasily Averin <vvs@virtuozzo.com>
Cc: Huang Ying <ying.huang@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3fa750dcf2 ]
write_cache_pages() is used in both background and integrity writeback
scenarios by various filesystems. Background writeback is mostly
concerned with cleaning a certain number of dirty pages based on various
mm heuristics. It may not write the full set of dirty pages or wait for
I/O to complete. Integrity writeback is responsible for persisting a set
of dirty pages before the writeback job completes. For example, an
fsync() call must perform integrity writeback to ensure data is on disk
before the call returns.
write_cache_pages() unconditionally breaks out of its processing loop in
the event of a ->writepage() error. This is fine for background
writeback, which had no strict requirements and will eventually come
around again. This can cause problems for integrity writeback on
filesystems that might need to clean up state associated with failed page
writeouts. For example, XFS performs internal delayed allocation
accounting before returning a ->writepage() error, where applicable. If
the current writeback happens to be associated with an unmount and
write_cache_pages() completes the writeback prematurely due to error, the
filesystem is unmounted in an inconsistent state if dirty+delalloc pages
still exist.
To handle this problem, update write_cache_pages() to always process the
full set of pages for integrity writeback regardless of ->writepage()
errors. Save the first encountered error and return it to the caller once
complete. This facilitates XFS (or any other fs that expects integrity
writeback to process the entire set of dirty pages) to clean up its
internal state completely in the event of persistent mapping errors.
Background writeback continues to exit on the first error encountered.
[akpm@linux-foundation.org: fix typo in comment]
Link: http://lkml.kernel.org/r/20181116134304.32440-1-bfoster@redhat.com
Signed-off-by: Brian Foster <bfoster@redhat.com>
Reviewed-by: Jan Kara <jack@suse.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3cc31fa65d ]
iomap_is_partially_uptodate() is intended to check wither blocks within
the selected range of a not-uptodate page are uptodate; if the range we
care about is up to date, it's an optimization.
However, the iomap implementation continues to check all blocks up to
from+count, which is beyond the page, and can even be well beyond the
iop->uptodate bitmap.
I think the worst that will happen is that we may eventually find a zero
bit and return "not partially uptodate" when it would have otherwise
returned true, and skip the optimization. Still, it's clearly an invalid
memory access that must be fixed.
So: fix this by limiting the search to within the page as is done in the
non-iomap variant, block_is_partially_uptodate().
Zorro noticed thiswhen KASAN went off for 512 byte blocks on a 64k
page system:
BUG: KASAN: slab-out-of-bounds in iomap_is_partially_uptodate+0x1a0/0x1e0
Read of size 8 at addr ffff800120c3a318 by task fsstress/22337
Reported-by: Zorro Lang <zlang@redhat.com>
Signed-off-by: Eric Sandeen <sandeen@redhat.com>
Signed-off-by: Eric Sandeen <sandeen@sandeen.net>
Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8b23eee4e5 ]
The shadow page table contains ptes for translations from nested guest
address to host address. Currently when creating these ptes we take the
rc bits from the pte for the L1 guest address to host address
translation. This is incorrect as we must also factor in the rc bits
from the pte for the nested guest address to L1 guest address
translation (as contained in the L1 guest partition table for the nested
guest).
By not calculating these bits correctly L1 may not have been correctly
notified when it needed to update its rc bits in the partition table it
maintains for its nested guest.
Modify the code so that the rc bits in the resultant pte for the L2->L0
translation are the 'and' of the rc bits in the L2->L1 pte and the L1->L0
pte, also accounting for whether this was a write access when setting
the dirty bit.
Signed-off-by: Suraj Jitindar Singh <sjitindarsingh@gmail.com>
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8400f87406 ]
Nested rmap entries are used to store the translation from L1 gpa to L2
gpa when entries are inserted into the shadow (nested) page tables. This
rmap list is located by indexing the rmap array in the memslot by L1
gfn. When we come to search for these entries we only know the L1 page size
(which could be PAGE_SIZE, 2M or a 1G page) and so can only select a gfn
aligned to that size. This means that when we insert the entry, so we can
find it later, we need to align the gfn we use to select the rmap list
in which to insert the entry to L1 page size as well.
By not doing this we were missing nested rmap entries when modifying L1
ptes which were for a page also passed through to an L2 guest.
Signed-off-by: Suraj Jitindar Singh <sjitindarsingh@gmail.com>
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e57b2945aa ]
We must free all irqs during shutdown, else kexec's 2nd kernel would hang
in pqi_wait_for_completion_io() as below:
Call trace:
pqi_wait_for_completion_io
pqi_submit_raid_request_synchronous.constprop.78+0x23c/0x310 [smartpqi]
pqi_configure_events+0xec/0x1f8 [smartpqi]
pqi_ctrl_init+0x814/0xca0 [smartpqi]
pqi_pci_probe+0x400/0x46c [smartpqi]
local_pci_probe+0x48/0xb0
pci_device_probe+0x14c/0x1b0
really_probe+0x218/0x3fc
driver_probe_device+0x70/0x140
__driver_attach+0x11c/0x134
bus_for_each_dev+0x70/0xc8
driver_attach+0x30/0x38
bus_add_driver+0x1f0/0x294
driver_register+0x74/0x12c
__pci_register_driver+0x64/0x70
pqi_init+0xd0/0x10000 [smartpqi]
do_one_initcall+0x60/0x1d8
do_init_module+0x64/0x1f8
load_module+0x10ec/0x1350
__se_sys_finit_module+0xd4/0x100
__arm64_sys_finit_module+0x28/0x34
el0_svc_handler+0x104/0x160
el0_svc+0x8/0xc
This happens only in the following combinations:
1. smartpqi is built as module, not built-in;
2. We have a disk connected to smartpqi card;
3. Both kexec's 1st and 2nd kernels use this disk as Rootfs' mount point.
Signed-off-by: Yanjiang Jin <yanjiang.jin@hxt-semitech.com>
Acked-by: Don Brace <don.brace@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2d3b55853b ]
There was a race condition in SMP that an ath10k_peer was created but its
member sta was null. Following are procedures of ath10k_peer creation and
member sta access in peer statistics path.
1. Peer creation:
ath10k_peer_create()
=>ath10k_wmi_peer_create()
=>ath10k_wait_for_peer_created()
...
# another kernel path, RX from firmware
ath10k_htt_t2h_msg_handler()
=>ath10k_peer_map_event()
=>wake_up()
# ar->peer_map[id] = peer //add peer to map
#wake up original path from waiting
...
# peer->sta = sta //sta assignment
2. RX path of statistics
ath10k_htt_t2h_msg_handler()
=>ath10k_update_per_peer_tx_stats()
=>ath10k_htt_fetch_peer_stats()
# peer->sta //sta accessing
Any access of peer->sta after peer was added to peer_map but before sta was
assigned could cause a null pointer issue. And because these two steps are
asynchronous, no proper lock can protect them. So both peer and sta need to
be checked before access.
Tested: QCA9984 with firmware ver 10.4-3.9.0.1-00005
Signed-off-by: Zhi Chen <zhichen@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2ba55c9851 ]
Problem:
The Linux kernel takes a logical volume offline after a LUN reset. This is
generally accompanied by this message in the dmesg output:
Device offlined - not ready after error recovery
Root Cause:
The root cause is a "quirk" in the timeout handling in the Linux SCSI
layer. The Linux kernel places a 30-second timeout on most media access
commands (reads and writes) that it send to device drivers. When a media
access command times out, the Linux kernel goes into error recovery mode
for the LUN that was the target of the command that timed out. Every
command that timed out is kept on a list inside of the Linux kernel to be
retried later. The kernel attempts to recover the command(s) that timed out
by issuing a LUN reset followed by a TEST UNIT READY. If the LUN reset and
TEST UNIT READY commands are successful, the kernel retries the command(s)
that timed out.
Each SCSI command issued by the kernel has a result field associated with
it. This field indicates the final result of the command (success or
error). When a command times out, the kernel places a value in this result
field indicating that the command timed out.
The "quirk" is that after the LUN reset and TEST UNIT READY commands are
completed, the kernel checks each command on the timed-out command list
before retrying it. If the result field is still "timed out", the kernel
treats that command as not having been successfully recovered for a
retry. If the number of commands that are in this state are greater than
two, the kernel takes the LUN offline.
Fix:
When our RAIDStack receives a LUN reset, it simply waits until all
outstanding commands complete. Generally, all of these outstanding commands
complete successfully. Therefore, the fix in the smartpqi driver is to
always set the command result field to indicate success when a request
completes successfully. This normally isn’t necessary because the result
field is always initialized to success when the command is submitted to the
driver. So when the command completes successfully, the result field is
left untouched. But in this case, the kernel changes the result field
behind the driver’s back and then expects the field to be changed by the
driver as the commands that timed-out complete.
Reviewed-by: Dave Carroll <david.carroll@microsemi.com>
Reviewed-by: Scott Teel <scott.teel@microsemi.com>
Signed-off-by: Kevin Barnett <kevin.barnett@microsemi.com>
Signed-off-by: Don Brace <don.brace@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 23c3828aa2 ]
With commit 09c2f95ad4 ("scsi: mpt3sas: Swap I/O memory read value back
to cpu endianness"), 64bit writes in _base_writeq() were rewritten to use
__raw_writeq() instad of writeq().
This introduced a bug apparent on powerpc64 systems such as the Raptor
Talos II that causes the HBA to drop from the PCIe bus under heavy load and
being reinitialized after a couple of seconds.
It can easily be triggered on affacted systems by using something like
fio --name=random-write --iodepth=4 --rw=randwrite --bs=4k --direct=0 \
--size=128M --numjobs=64 --end_fsync=1
fio --name=random-write --iodepth=4 --rw=randwrite --bs=64k --direct=0 \
--size=128M --numjobs=64 --end_fsync=1
a couple of times. In my case I tested it on both a ZFS raidz2 and a btrfs
raid6 using LSI 9300-8i and 9400-8i controllers.
The fix consists in resembling the write ordering of writeq() by adding a
mandatory write memory barrier before device access and a compiler barrier
afterwards. The additional MMIO barrier is superfluous.
Signed-off-by: Stephan Günther <moepi@moepi.net>
Reported-by: Matt Corallo <linux@bluematt.me>
Acked-by: Sreekanth Reddy <Sreekanth.Reddy@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
