To make the fastboot checks at least somewhat sensible let's mark
the expected DPLL as the active one right after we finished the
state computation. Otherwise intel_pipe_config_compare() will
always be comparing things against NULL/0.
TODO: This is still not really right. If the previous commit
had to fall back to the other PLL then the comparisong will
now fail. I guess intel_pipe_config_compare() should rather
be comparing port_dplls[] instead. But to do that we really
should just unify every platform to use the port_dplls[]
approach whether they have any need for PLL fallbacks or not.
Acked-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220907091057.11572-12-ville.syrjala@linux.intel.com
Now that we no longer fuzz M/N during fastset these should
match exctly.
In order to get a match with what the BIOS does we need to round
M/N down. And we do the opposite rounding when doing the readback.
That gets us pretty much the same thing back.
There can still be slight rounding differences between FDI M/N
vs. the DPLL output so we allow for tiny deviation in
intel_pipe_config_sanity_check().
v2: Tweak rounding/sanity check stuff a bit
Reviewed-by: Jani Nikula <jani.nikula@intel.com> #v1
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220907091057.11572-10-ville.syrjala@linux.intel.com
Do the DPLL computation before fastset checks. This should
allow us to get rid of all that horrible fuzzy clock handling
for fastsets. Who knows how many bugs there are caused by our
state not actually matching what the hardware will generate.
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220907091057.11572-9-ville.syrjala@linux.intel.com
Fill port_clock and hw.adjusted_mode.crtc_clock with the actual
frequency we're going to be getting from the hardware. This will
let us accurately compute all derived state that depends on those.
v2: Reintroduce iCLKIP WARN
v3: Try to deal with VLV/BXT DSI PLL as well
Reviewed-by: Jani Nikula <jani.nikula@intel.com> #v1
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220907091057.11572-8-ville.syrjala@linux.intel.com
Only reassign the pipe's DPLL if it's going through a full
.compute_config() cycle. If OTOH it's just getting modeset
eg. in order to change cdclk there doesn't seem much point in
picking a new DPLL for it.
This should also prevent .get_dplls() from seeing a funky port_clock
for DP even in cases where the readout produces a non-standard
clock and we (for some reason) have decided to not fully recompute
the state to remedy the situation.
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220907091057.11572-7-ville.syrjala@linux.intel.com
Currently we calculate a lot of things (pixel rate, watermarks,
cdclk) trusting that the DPLL can generate the exact frequency
we ask it. In practice that is not true and there can be
certain amount of rounding involved.
To allow us to eventually get accurate numbers for all our
DPLL clock derived state we need to move the DPLL calculation
to hapen much earlier. To that end we hoist it up to the just
after the fastset checks. For now we just do the easy code
motion, and the actual back feeding of the final DPLL clock
into the state will come later.
A slight change here is that now .crtc_compute_clock()
can get called while the shared_dpll is still assigned.
But since .crtc_compute_clock() no longer assignes new
shared_dplls this is perfectly fine.
TODO: I'd actually like to do this before the fastset check
so that if the DPLL state should change we actually do the
modeset. Which I think is what the video aficionados want,
but it might not be what the fans of fastboot want. Not yet
sure how to reconcile those conflicting requirements...
v2: s/return/goto/ in error handling
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220907091057.11572-6-ville.syrjala@linux.intel.com
These chip versions are closely related and all of them have no
chip-specific MAC/PHY initialization. Therefore merge support
for the three chip versions.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Link: https://lore.kernel.org/r/469d27e0-1d06-9b15-6c96-6098b3a52e35@gmail.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Return the value pm_runtime_force_suspend() directly instead of storing
it in another redundant variable.
Reported-by: Zeal Robot <zealci@zte.com.cn>
Signed-off-by: ye xingchen <ye.xingchen@zte.com.cn>
Link: https://lore.kernel.org/r/20220908010429.342875-1-ye.xingchen@zte.com.cn
Signed-off-by: Mark Brown <broonie@kernel.org>
Most function in ak4458_probe() and ak4458_remove() are
duplicate with dai ops, so remove them and move dsd_path
setting to dai ops.
Signed-off-by: Shengjiu Wang <shengjiu.wang@nxp.com>
Reviewed-by: Daniel Baluta <daniel.baluta@nxp.com>
Link: https://lore.kernel.org/r/1662622316-23426-1-git-send-email-shengjiu.wang@nxp.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Return the value regmap_write() and sti_sas_init_sas_registers() directly
instead of storing it in another redundant variable.
Reported-by: Zeal Robot <zealci@zte.com.cn>
Signed-off-by: ye xingchen <ye.xingchen@zte.com.cn>
Link: https://lore.kernel.org/r/20220908010304.342760-1-ye.xingchen@zte.com.cn
Signed-off-by: Mark Brown <broonie@kernel.org>
The Amp is already control in userspace before trigger calibrate function.
Remove unnecessary control in calibrate function and
add condition to check calibration is ready.
Signed-off-by: Steve Lee <steve.lee.analog@gmail.com>
Link: https://lore.kernel.org/r/20220908060359.13606-1-steve.lee.analog@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
snd_soc_dai_link_event_pre_pmu() is using if/else for config->formats
check, but "else" case is for just error.
Unnecessary if/else is not good for readable code. this patch checks
if config->formats was zero as error case.
Moreover, we don't need to indicate config->formats value in error message,
because it is zero. This patch tidyup it, too.
=> if (config->formats) {
...
} else {
dev_warn(w->dapm->dev, "ASoC: Invalid format %llx specified\n",
=> config->formats);
...
}
Link: https://lore.kernel.org/all/YxiDkDOwRsbXeZ17@sirena.org.uk/
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Link: https://lore.kernel.org/r/877d2ebn3t.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>
In preparation to make memory operations accessible for a non
ffa_driver/device, it is better to split the ffa_ops into different
categories of operations: info, message and memory. The info and memory
are ffa_device independent and can be used without any associated
ffa_device from a non ffa_driver.
However, we don't export these info and memory APIs yet without the user.
The first users of these APIs can export them.
Link: https://lore.kernel.org/r/20220907145240.1683088-11-sudeep.holla@arm.com
Reviewed-by: Jens Wiklander <jens.wiklander@linaro.org>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
FF-A v1.1 adds a flag in the partition properties to indicate if the
partition runs in the AArch32 or AArch64 execution state. Use the same
to set-up the 32-bit execution flag mode in the ffa_dev automatically
if the detected firmware version is above v1.0 and ignore any requests
to do the same from the ffa_driver.
Link: https://lore.kernel.org/r/20220907145240.1683088-10-sudeep.holla@arm.com
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
FF-A v1.1 adds support to discovery the UUIDs of the partitions that was
missing in v1.0 and which the driver workarounds by using UUIDs supplied
by the ffa_drivers.
Add the v1.1 get_partition_info support and disable the workaround if
the detected FF-A version is greater than v1.0.
Link: https://lore.kernel.org/r/20220907145240.1683088-9-sudeep.holla@arm.com
Reviewed-by: Jens Wiklander <jens.wiklander@linaro.org>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Except the message APIs, all other APIs are ffa_device independent and can
be used without any associated ffa_device from a non ffa_driver.
In order to reflect the same, just rename ffa_dev_ops as ffa_ops to
avoid any confusion or to keep it simple.
Link: https://lore.kernel.org/r/20220907145240.1683088-8-sudeep.holla@arm.com
Suggested-by: Sumit Garg <sumit.garg@linaro.org>
Reviewed-by: Sumit Garg <sumit.garg@linaro.org>
Reviewed-by: Jens Wiklander <jens.wiklander@linaro.org>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
There is a requirement to make memory APIs independent of the ffa_device.
One of the use-case is to have a common memory driver that manages the
memory for all the ffa_devices. That common memory driver won't be a
ffa_driver or won't have any ffa_device associated with it. So having
these memory APIs accessible without a ffa_device is needed and should
be possible as most of these are handled by the partition manager(SPM
or hypervisor).
Drop the ffa_device argument to the memory APIs and make them ffa_device
independent.
Link: https://lore.kernel.org/r/20220907145240.1683088-7-sudeep.holla@arm.com
Acked-by: Jens Wiklander <jens.wiklander@linaro.org>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Currently, the ffa_dev->mode_32bit is use to detect if the native 64-bit
or 32-bit versions of FF-A ABI needs to be used. However for the FF-A
memory ABIs, it is not dependent on the ffa_device(i.e. the partition)
itself, but the partition manager(SPM).
So, the FFA_FEATURES can be use to detect if the native 64bit ABIs are
supported or not and appropriate calls can be made based on that.
Use FFA_FEATURES to detect if native versions of MEM_LEND or MEM_SHARE
are implemented and make of the same to use native memory ABIs later on.
Link: https://lore.kernel.org/r/20220907145240.1683088-6-sudeep.holla@arm.com
Reviewed-by: Jens Wiklander <jens.wiklander@linaro.org>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Add support for FFA_FEATURES to discover properties supported at the
FF-A interface. This interface can be used to query:
- If an FF-A interface is implemented by the component at the higher EL,
- If an implemented FF-A interface also implements any optional features
described in its interface definition, and
- Any implementation details exported by an implemented FF-A interface
as described in its interface definition.
Link: https://lore.kernel.org/r/20220907145240.1683088-5-sudeep.holla@arm.com
Reviewed-by: Jens Wiklander <jens.wiklander@linaro.org>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
The only user of this exported ffa_dev_ops_get() was OPTEE driver which
now uses ffa_dev->ops directly, there are no other users for this.
Also, since any ffa driver can use ffa_dev->ops directly, there will be
no need for ffa_dev_ops_get(), so just remove ffa_dev_ops_get().
Link: https://lore.kernel.org/r/20220907145240.1683088-4-sudeep.holla@arm.com
Reviewed-by: Jens Wiklander <jens.wiklander@linaro.org>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Now that the ffa_device structure holds the pointer to ffa_dev_ops,
there is no need to obtain the same through ffa_dev_ops_get().
Just use the ffa_dev->ops directly. Since the ffa_device itself carries
ffa_dev_ops now, there is no need to keep a copy in optee_ffa structure.
Drop ffa_ops in the optee_ffa structure as it is not needed anymore.
Link: https://lore.kernel.org/r/20220907145240.1683088-3-sudeep.holla@arm.com
Reviewed-by: Jens Wiklander <jens.wiklander@linaro.org>
Reviewed-by: Sumit Garg <sumit.garg@linaro.org>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Currently ffa_dev_ops_get() is the way to fetch the ffa_dev_ops pointer.
It checks if the ffa_dev structure pointer is valid before returning the
ffa_dev_ops pointer.
Instead, the pointer can be made part of the ffa_dev structure and since
the core driver is incharge of creating ffa_device for each identified
partition, there is no need to check for the validity explicitly if the
pointer is embedded in the structure.
Add the pointer to the ffa_dev_ops in the ffa_dev structure itself and
initialise the same as part of creation of the device.
Link: https://lore.kernel.org/r/20220907145240.1683088-2-sudeep.holla@arm.com
Reviewed-by: Jens Wiklander <jens.wiklander@linaro.org>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Fix regression introduced by commit:
"drm/i915: Individualize fences before adding to dma_resv obj"
which sets obj->read_domains to 0 for both read and write paths.
Also set obj->write_domain to 0 on read path which was removed by
the commit.
References: https://gitlab.freedesktop.org/drm/intel/-/issues/6639
Fixes: 420a07b841 ("drm/i915: Individualize fences before adding to dma_resv obj")
Signed-off-by: Nirmoy Das <nirmoy.das@intel.com>
Cc: <stable@vger.kernel.org> # v5.16+
Cc: Matthew Auld <matthew.auld@intel.com>
Cc: Andrzej Hajda <andrzej.hajda@intel.com>
Reviewed-by: Andrzej Hajda <andrzej.hajda@intel.com>
Signed-off-by: Matthew Auld <matthew.auld@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220907172641.12555-1-nirmoy.das@intel.com
Enabling panfrost GPU OPP with dynamic regulator will make OPP
responsible to enable and configure it.
Unfortunately OPP configure and enable the regulator when an OPP
is asked to be set, which is not the case during
panfrost_devfreq_init().
This leave the regulator unconfigured and if no GPU load is
triggered, no OPP is asked to be set which make the regulator framework
switching it off during regulator_late_cleanup() without
noticing and therefore make the board hang as any access to GPU
memory space make bus locks up.
Call dev_pm_opp_set_opp() with the recommend OPP in
panfrost_devfreq_init() to enable the regulator, this will properly
configure and enable the regulator and will avoid any switch off
by regulator_late_cleanup().
Suggested-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Clément Péron <peron.clem@gmail.com>
Reviewed-by: Steven Price <steven.price@arm.com>
Signed-off-by: Steven Price <steven.price@arm.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220906153034.153321-5-peron.clem@gmail.com
So far, different views (normal, partial, rotated and remapped)
into the same object are only supported for GGTT mappings.
But with the upcoming VM_BIND feature, PPGTT will also use the
partial view mapping. Hence rename ggtt_view to more generic
gtt_view.
Signed-off-by: Niranjana Vishwanathapura <niranjana.vishwanathapura@intel.com>
Acked-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220901183854.3446-1-niranjana.vishwanathapura@intel.com
Cong Wang noticed that the previous fix for sch_sfb accessing the queued
skb after enqueueing it to a child qdisc was incomplete: the SFB enqueue
function was also calling qdisc_qstats_backlog_inc() after enqueue, which
reads the pkt len from the skb cb field. Fix this by also storing the skb
len, and using the stored value to increment the backlog after enqueueing.
Fixes: 9efd23297c ("sch_sfb: Don't assume the skb is still around after enqueueing to child")
Signed-off-by: Toke Høiland-Jørgensen <toke@toke.dk>
Acked-by: Cong Wang <cong.wang@bytedance.com>
Link: https://lore.kernel.org/r/20220905192137.965549-1-toke@toke.dk
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Currently phy link up/down interrupt is enabled using the
LAN87xx_INTERRUPT_MASK register. In the lan87xx_read_status function,
phy link is determined using the T1_MODE_STAT_REG register comm_ready bit.
comm_ready bit is set using the loc_rcvr_status & rem_rcvr_status.
Whenever the phy link is up, LAN87xx_INTERRUPT_SOURCE link_up bit is set
first but comm_ready bit takes some time to set based on local and
remote receiver status.
As per the current implementation, interrupt is triggered using link_up
but the comm_ready bit is still cleared in the read_status function. So,
link is always down. Initially tested with the shared interrupt
mechanism with switch and internal phy which is working, but after
implementing interrupt controller it is not working.
It can fixed either by updating the read_status function to read from
LAN87XX_INTERRUPT_SOURCE register or enable the interrupt mask for
comm_ready bit. But the validation team recommends the use of comm_ready
for link detection.
This patch fixes by enabling the comm_ready bit for link_up in the
LAN87XX_INTERRUPT_MASK_2 register (MISC Bank) and link_down in
LAN87xx_INTERRUPT_MASK register.
Fixes: 8a1b415d70 ("net: phy: added ethtool master-slave configuration support")
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20220905152750.5079-1-arun.ramadoss@microchip.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
The simple display pipeline is a set of helpers that can be used by DRM
drivers to avoid dealing with all the needed components and just define
a few functions to operate a simple display device with one full-screen
scanout buffer feeding a single output.
But it is arguable that this provides the correct level of abstraction
for simple drivers, and recently some have been ported from using these
simple display helpers to use the regular atomic helpers instead.
The rationale for this is that the simple display pipeline helpers don't
hide that much of the DRM complexity, while adding an indirection layer
that conflates the concepts of CRTCs and planes. This makes the helpers
less flexible and harder to be reused among different graphics drivers.
Also, for simple drivers, using the full atomic helpers doesn't require
a lot of additional code. So adding a simple display pipeline layer may
not be worth it.
For these reasons, let's follow that trend and make ssd130x a plain DRM
driver that creates its own primary plane, CRTC, enconder and connector.
Suggested-by: Thomas Zimmermann <tzimmermann@suse.de>
Signed-off-by: Javier Martinez Canillas <javierm@redhat.com>
Acked-by: Thomas Zimmermann <tzimmermann@suse.de>
Link: https://patchwork.freedesktop.org/patch/msgid/20220905222759.2597186-1-javierm@redhat.com
GPIO library now accepts fwnode as a firmware node, so
switch the driver to use it.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Link: https://lore.kernel.org/r/20220905180034.73132-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
fwnode_irq_get() may return all possible signed values, such as Linux
error code. Fix the code to handle this properly.
Fixes: be2dc859ab ("pinctrl: pinctrl-microchip-sgpio: Add irq support (for sparx5)")
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Michael Walle <michael@walle.cc>
Link: https://lore.kernel.org/r/20220906115021.8661-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The stmmac has the possibility to automatically strip the padding/FCS for IEEE
802.3 type frames. This feature is enabled conditionally. Therefore, the stmmac
receive path has to have a determination logic whether the FCS has to be
stripped in software or not.
In fact, for DSA this ACS feature is disabled and the determination logic
doesn't check for it properly. For instance, when using DSA in combination with
an older stmmac (pre version 4), the FCS is not stripped by hardware or software
which is problematic.
So either add another check for DSA to the fast path or simply disable ACS
feature completely. The latter approach has been chosen, because most of the
time the FCS is stripped in software anyway and it removes conditionals from the
receive fast path.
Signed-off-by: Kurt Kanzenbach <kurt@linutronix.de>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/87v8q8jjgh.fsf@kurt/
Link: https://lore.kernel.org/r/20220905130155.193640-1-kurt@linutronix.de
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Ideally this and similar common properties will be inherited so you
won't need to paste them in every pinctrl binding.
Signed-off-by: Iskren Chernev <iskren.chernev@gmail.com>
Reviewed-by: Caleb Connolly <caleb@connolly.tech>
Link: https://lore.kernel.org/r/20220903174150.3566935-5-iskren.chernev@gmail.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
PINCTRL_IMX depends on OF, however the dependency is missed when selected
by PINCTRL_IMX8M* (it does not follow the indirect 'select' statements),
select it explicitly.
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Linus Walleij <linus.walleij@linaro.org>
Reported-by: kernel test robot <lkp@intel.com>
Link: https://lore.kernel.org/all/202209050605.fezJUgFH-lkp@intel.com/
Fixes: 87c2a29a6b ("pinctrl: imx8m: kconfig: Depends on SOC_IMX8M")
Signed-off-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Reviewed-by: Jacky Bai <ping.bai@nxp.com>
Link: https://lore.kernel.org/r/20220905224408.346425-1-francesco.dolcini@toradex.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
In a few comments the style is not aligned with the rest.
Correct them.
While at it, drop unneeded blank lines and deduplicate 'Author'.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Tested-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Link: https://lore.kernel.org/r/20220902182650.83098-17-andriy.shevchenko@linux.intel.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Make use of the GENMASK() (far less error-prone, far more concise).
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Tested-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Link: https://lore.kernel.org/r/20220902182650.83098-16-andriy.shevchenko@linux.intel.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
ACPI table on Intel Galileo Gen 1 has wrong pin number for IRQ resource
of the I²C GPIO expander. Since we know what that number is and luckily
have GPIO bases fixed for SoC's controllers, we may use a simple DMI quirk
to match the platform and retrieve GpioInt() pin on it for the expander in
question.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Tested-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Link: https://lore.kernel.org/r/20220902182650.83098-15-andriy.shevchenko@linux.intel.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add support of the expander found on Intel Galileo Gen1 board.
The platform information comes from ACPI.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Tested-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Link: https://lore.kernel.org/r/20220902182650.83098-14-andriy.shevchenko@linux.intel.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Convert the module to be property provider agnostic and allow
it to be used on non-OF platforms.
Add mod_devicetable.h include.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Tested-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Link: https://lore.kernel.org/r/20220902182650.83098-13-andriy.shevchenko@linux.intel.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The introduced callback ->pin_dbg_show() is useful for debugging.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Tested-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Link: https://lore.kernel.org/r/20220902182650.83098-12-andriy.shevchenko@linux.intel.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Move the default values to the 'default' case in the switches.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Tested-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Link: https://lore.kernel.org/r/20220902182650.83098-11-andriy.shevchenko@linux.intel.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Since we have pin configuration getter and setter provided,
there is no need to duplicate that in the custom ->set_config().
Instead, switch to gpiochip_generic_config().
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Tested-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Link: https://lore.kernel.org/r/20220902182650.83098-10-andriy.shevchenko@linux.intel.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The pin control framework checks pin boundaries before calling
the respective driver's callbacks. Hence no need to check for
pin boundaries, the respective conditionals won't be ever true.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Tested-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Link: https://lore.kernel.org/r/20220902182650.83098-9-andriy.shevchenko@linux.intel.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The Cypress CY8C95x0 chips have an internal EEPROM that defines
initial configuration. It might be that bootloader or other
entity wrote the platform related setup into it. Don't override
it in the driver.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Tested-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Link: https://lore.kernel.org/r/20220902182650.83098-8-andriy.shevchenko@linux.intel.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Since it's a pin control, GPIO counterpart needs to know the mapping
between pin numbering and GPIO numbering. Enable this by calling
gpiochip_add_pin_range() at the chip addition time.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Tested-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Link: https://lore.kernel.org/r/20220902182650.83098-7-andriy.shevchenko@linux.intel.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>