Heiner Kallweit says:
====================
r8169: remove support for few unused chip versions
There's a number of chip versions that apparently never made it to the
mass market. Detection of these chip versions has been disabled for
few kernel versions now and nobody complained. Therefore remove
support for these chip versions.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Detection of this chip version has been disabled for few kernel versions now.
Nobody complained, so remove support for this chip version.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Detection of this chip version has been disabled for few kernel versions now.
Nobody complained, so remove support for this chip version.
v3:
- rebase patch
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Detection of this chip version has been disabled for few kernel versions now.
Nobody complained, so remove support for this chip version.
v2:
- fix a typo: RTL_GIGA_MAC_VER_40 -> RTL_GIGA_MAC_VER_50
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Detection of these chip versions has been disabled for few kernel versions now.
Nobody complained, so remove support for this chip version.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Detection of this chip version has been disabled for few kernel versions now.
Nobody complained, so remove support for this chip version.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Roi Dayan Says:
===============
Add support for SF tunnel offload
Mlx5 driver only supports VF tunnel offload.
To add support for SF tunnel offload the driver needs to:
1. Add send-to-vport metadata matching rules like done for VFs.
2. Set an indirect table for SF vport, same as VF vport.
info smaller sub functions for better maintainability.
rules from esw init phase to representor load phase.
SFs could be created after esw initialized and thus the send-to-vport
meta rules would not be created for those SFs.
By moving the creation of the rules to representor load phase
we ensure creating the rules also for SFs created later.
===============
Lama Kayal Says:
================
Make flow steering API loosely coupled from mlx5e_priv, in a manner to
introduce more readable and maintainable modules.
Make TC's private, let mlx5e_flow_steering struct be dynamically allocated,
and introduce its API to maintain the code via setters and getters
instead of publicly exposing it.
Introduce flow steering debug macros to provide an elegant finish to the
decoupled flow steering API, where errors related to flow steering shall
be reported via them.
All flow steering related files will drop any coupling to mlx5e_priv,
instead they will get the relevant members as input. Among these,
fs_tt_redirect, fs_tc, and arfs.
================
-----BEGIN PGP SIGNATURE-----
iQEzBAABCAAdFiEEGhZs6bAKwk/OTgTpSD+KveBX+j4FAmMEaToACgkQSD+KveBX
+j7H1wf8DPInwK4MsgilUZFXNd03RJprlptami+Feev2wmuzOIOwyTxOc+VvowFM
G6r0Yuqahg0z5oE7zgxMNNdtKevjqmaNLWuDtbvv4UQKt7hwJz28Y0Ezuz3L9sQS
JVEQpII/FhUFzHoeDTbbJojKGTO7N8hS4D7ZB9wGeQc7M8PmLiUq19PURKwGDxUq
EhNwEgxOzbd6S5OMGfD0bDOOK+TpntKctkXUpYh7rr6JlLQpor03cBfYrOx9DcST
M3Yk9ianx4fmeOeyZAAZOEzUpBkwMt74SxelIcwAAei9bcNRRI3FoNLc+PcKJjz1
c567AeSzx/HYnaoydtGFOroq8lAwnw==
=pgqu
-----END PGP SIGNATURE-----
Merge tag 'mlx5-updates-2022-08-22' of git://git.kernel.org/pub/scm/linux/kernel/git/saeed/linux
mlx5-updates-2022-08-22
Roi Dayan Says:
===============
Add support for SF tunnel offload
Mlx5 driver only supports VF tunnel offload.
To add support for SF tunnel offload the driver needs to:
1. Add send-to-vport metadata matching rules like done for VFs.
2. Set an indirect table for SF vport, same as VF vport.
info smaller sub functions for better maintainability.
rules from esw init phase to representor load phase.
SFs could be created after esw initialized and thus the send-to-vport
meta rules would not be created for those SFs.
By moving the creation of the rules to representor load phase
we ensure creating the rules also for SFs created later.
===============
Lama Kayal Says:
================
Make flow steering API loosely coupled from mlx5e_priv, in a manner to
introduce more readable and maintainable modules.
Make TC's private, let mlx5e_flow_steering struct be dynamically allocated,
and introduce its API to maintain the code via setters and getters
instead of publicly exposing it.
Introduce flow steering debug macros to provide an elegant finish to the
decoupled flow steering API, where errors related to flow steering shall
be reported via them.
All flow steering related files will drop any coupling to mlx5e_priv,
instead they will get the relevant members as input. Among these,
fs_tt_redirect, fs_tc, and arfs.
================
skb_copy_bits() could fail, which requires a check on the return
value.
Signed-off-by: Li Zhong <floridsleeves@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Issue found during code review. This bug has no impact as long as the
ks8851_net structure is the first element of the ks8851_net_spi structure.
As long as the offset to the ks8851_net struct is zero, the container_of()
macro is subtracting 0 and therefore no damage done. But if the
ks8851_net_spi struct is ever modified such that the ks8851_net struct
within it is no longer the first element of the struct, then the bug would
manifest itself and cause problems.
struct ks8851_net is contained within ks8851_net_spi.
ks is contained within kss.
kss is the priv_data of the netdev structure.
Signed-off-by: Jerry Ray <jerry.ray@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
tcp_md5sig_pool_populated can be read while another thread
changes its value.
The race has no consequence because allocations
are protected with tcp_md5sig_mutex.
This patch adds READ_ONCE() and WRITE_ONCE() to document
the race and silence KCSAN.
Reported-by: Abhishek Shah <abhishek.shah@columbia.edu>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Both <port> br_port_locked and <lag> interfaces's flag
offloading is supported. No new ABI is being added,
rather existing (port_param_set) API call gets extended.
Signed-off-by: Oleksandr Mazur <oleksandr.mazur@plvision.eu>
V2:
add missing receipents (linux-kernel, netdev)
Signed-off-by: David S. Miller <davem@davemloft.net>
Steffen Klassert says:
====================
pull request (net): ipsec 2022-08-24
1) Fix a refcount leak in __xfrm_policy_check.
From Xin Xiong.
2) Revert "xfrm: update SA curlft.use_time". This
violates RFC 2367. From Antony Antony.
3) Fix a comment on XFRMA_LASTUSED.
From Antony Antony.
4) x->lastused is not cloned in xfrm_do_migrate.
Fix from Antony Antony.
5) Serialize the calls to xfrm_probe_algs.
From Herbert Xu.
6) Fix a null pointer dereference of dst->dev on a metadata
dst in xfrm_lookup_with_ifid. From Nikolay Aleksandrov.
Please pull or let me know if there are problems.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Recent versions of dt-schema warn about unevaluatedProperties:
arch/riscv/boot/dts/microchip/mpfs-icicle-kit.dtb: pcie@2000000000: Unevaluated properties are not allowed ('clock-names', 'clocks', 'legacy-interrupt-controller', 'microchip,axi-m-atr0' were unexpected)
From schema: Documentation/devicetree/bindings/pci/microchip,pcie-host.yaml
The clocks are required to enable interfaces between the FPGA fabric
and the core complex, so add them to the binding.
Link: https://lore.kernel.org/r/20220819231415.3860210-3-mail@conchuod.ie
Fixes: 6ee6c89aac ("dt-bindings: PCI: microchip: Add Microchip PolarFire host binding")
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
Signed-off-by: Lorenzo Pieralisi <lpieralisi@kernel.org>
Reviewed-by: Rob Herring <robh@kernel.org>
The commit b92225b034 ("dt-bindings: PCI: designware: Fix
'unevaluatedProperties' warnings") removed the clock-names property as
a requirement and from the example as it triggered unevaluatedProperty
warnings. dtbs_check was not able to pick up on this at the time, but
now can:
arch/riscv/boot/dts/sifive/hifive-unmatched-a00.dtb: pcie@e00000000: Unevaluated properties are not allowed ('clock-names' was unexpected)
From schema: linux/Documentation/devicetree/bindings/pci/sifive,fu740-pcie.yaml
The property was already in use by the FU740 DTS and the clock must be
enabled. The Linux and FreeBSD drivers require the property to enable
the clocks correctly Re-add the property and its "clocks" dependency,
while making it required.
Link: https://lore.kernel.org/r/20220819231415.3860210-2-mail@conchuod.ie
Fixes: b92225b034 ("dt-bindings: PCI: designware: Fix 'unevaluatedProperties' warnings")
Fixes: 43cea116be ("dt-bindings: PCI: Add SiFive FU740 PCIe host controller")
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
Signed-off-by: Lorenzo Pieralisi <lpieralisi@kernel.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Return the value from regmap_write() directly instead of storing it
in another redundant variable.
Reported-by: Zeal Robot <zealci@zte.com.cn>
Signed-off-by: ye xingchen <ye.xingchen@zte.com.cn>
Link: https://lore.kernel.org/r/20220824074707.221159-1-ye.xingchen@zte.com.cn
Signed-off-by: Mark Brown <broonie@kernel.org>
After using 'res_node' returned by of_parse_phandle(), of_node_put()
need be called to decrease the refcount.
Fixes: fb5319af6a ("ASoC: SOF: imx: Add i.MX8ULP HW support")
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Link: https://lore.kernel.org/r/20220824013234.375738-2-yangyingliang@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>
In a large enough fleet of computers, it is common to have a few bad CPUs.
Those can often be identified by seeing that some commonly run kernel code,
which runs fine everywhere else, keeps crashing on the same CPU core on one
particular bad system.
However, the failure modes in CPUs that have gone bad over the years are
often oddly specific, and the only bad behavior seen might be segfaults
in programs like bash, python, or various system daemons that run fine
everywhere else.
Add a printk() to show_signal_msg() to print the CPU, core, and socket
at segfault time.
This is not perfect, since the task might get rescheduled on another
CPU between when the fault hit, and when the message is printed, but in
practice this has been good enough to help people identify several bad
CPU cores.
For example:
segfault[1349]: segfault at 0 ip 000000000040113a sp 00007ffc6d32e360 error 4 in \
segfault[401000+1000] likely on CPU 0 (core 0, socket 0)
This printk can be controlled through /proc/sys/debug/exception-trace.
[ bp: Massage a bit, add "likely" to the printed line to denote that
the CPU number is not always reliable. ]
Signed-off-by: Rik van Riel <riel@surriel.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Link: https://lore.kernel.org/r/20220805101644.2e674553@imladris.surriel.com
Since the user can control the arguments provided to the kernel by the
ioctl() system call, an out-of-bounds bug occurs when the 'id->name'
provided by the user does not end with '\0'.
The following log can reveal it:
[ 10.002313] BUG: KASAN: stack-out-of-bounds in snd_ctl_find_id+0x36c/0x3a0
[ 10.002895] Read of size 1 at addr ffff888109f5fe28 by task snd/439
[ 10.004934] Call Trace:
[ 10.007140] snd_ctl_find_id+0x36c/0x3a0
[ 10.007489] snd_ctl_ioctl+0x6cf/0x10e0
Fix this by checking the bound of 'id->name' in the loop.
Fixes: c27e1efb61 ("ALSA: control: Use xarray for faster lookups")
Signed-off-by: Zheyu Ma <zheyuma97@gmail.com>
Link: https://lore.kernel.org/r/20220824081654.3767739-1-zheyuma97@gmail.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
On link state change, the controller gets reset,
causing PPS to drop out and the PHC to lose its
time and calibration. So we restart it if needed,
restoring calibration and time registers.
Changes since v2:
* Add `fec_ptp_save_state()`/`fec_ptp_restore_state()`
* Use `ktime_get_real_ns()`
* Use `BIT()` macro
Changes since v1:
* More ECR #define's
* Stop PPS in `fec_ptp_stop()`
Signed-off-by: Csókás Bence <csokas.bence@prolan.hu>
Signed-off-by: David S. Miller <davem@davemloft.net>
Siddharth Vadapalli says:
====================
J7200: CPSW5G: Add support for QSGMII mode to am65-cpsw driver
Add support for QSGMII mode to am65-cpsw driver.
Change log:
v4-> v5:
1. Move ti,j7200-cpswxg-nuss compatible to the line above the
ti,j721e-cpsw-nuss compatible.
2. Add allOf and move if-then statements within it to allow future if-then
statements to be added easily.
v3 -> v4:
1. Update bindings to disallow ports based on compatible, instead of
adding a new if/then statement for the new compatible.
2. Add Else-If condition for RMII mode in the set of supported interfaces.
Support for RMII mode is already present in the driver and I had
missed out adding a condition for RMII mode in the previous patches.
v2 -> v3:
1. In ti,k3-am654-cpsw-nuss.yaml, restrict if/then statement to port
nodes.
v1 -> v2:
1. Add new compatible for CPSW5G in ti,k3-am654-cpsw-nuss.yaml and extend
properties for new compatible.
2. Add extra_modes member to struct am65_cpsw_pdata to be used for QSGMII
mode by new compatible.
3. Add check for phylink supported modes to ensure that only one phy mode
is advertised as supported.
4. Check if extra_modes supports QSGMII mode in am65_cpsw_nuss_mac_config()
for register write.
5. Add check for assigning port->sgmii_base only when extra_modes is valid.
v4: https://lore.kernel.org/r/20220816060139.111934-1-s-vadapalli@ti.com/
v3: https://lore.kernel.org/r/20220606110443.30362-1-s-vadapalli@ti.com/
v2: https://lore.kernel.org/r/20220602114558.6204-1-s-vadapalli@ti.com/
v1: https://lore.kernel.org/r/20220531113058.23708-1-s-vadapalli@ti.com/
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
In TI's J7200 SoC CPSW5G ports, each of the 4 ports can be configured
as a QSGMII main or QSGMII-SUB port. This configuration is performed
by phy-gmii-sel driver on invoking the phy_set_mode_ext() function.
It is necessary for the QSGMII main port to be configured before any of
the QSGMII-SUB interfaces are brought up. Currently, the QSGMII-SUB
interfaces come up before the QSGMII main port is configured.
Fix this by moving the call to phy_set_mode_ext() from
am65_cpsw_nuss_ndo_slave_open() to am65_cpsw_nuss_init_slave_ports(),
thereby ensuring that the QSGMII main port is configured before any of
the QSGMII-SUB ports are brought up.
Signed-off-by: Siddharth Vadapalli <s-vadapalli@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
CPSW5G in J7200 supports additional modes like QSGMII and SGMII.
Add new compatible for J7200 and enable QSGMII mode in am65-cpsw driver.
Signed-off-by: Siddharth Vadapalli <s-vadapalli@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Update bindings for TI K3 J7200 SoC which contains 5 ports (4 external
ports) CPSW5G module and add compatible for it.
Changes made:
- Add new compatible ti,j7200-cpswxg-nuss for CPSW5G.
- Extend pattern properties for new compatible.
- Change maximum number of CPSW ports to 4 for new compatible.
Signed-off-by: Siddharth Vadapalli <s-vadapalli@ti.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
It is not allowed to call kfree_skb() from hardware interrupt
context or with interrupts being disabled. So add all skb to
a tmp list, then free them after spin_unlock_irqrestore() at
once.
Fixes: 66ba215cb5 ("neigh: fix possible DoS due to net iface start/stop loop")
Suggested-by: Denis V. Lunev <den@openvz.org>
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Reviewed-by: Nikolay Aleksandrov <razor@blackwall.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Sometimes, gcc will optimize the function by spliting it to two or
more functions. In this case, kfree_skb_reason() is splited to
kfree_skb_reason and kfree_skb_reason.part.0. However, the
function/tracepoint trace_kfree_skb() in it needs the return address
of kfree_skb_reason().
This split makes the call chains becomes:
kfree_skb_reason() -> kfree_skb_reason.part.0 -> trace_kfree_skb()
which makes the return address that passed to trace_kfree_skb() be
kfree_skb().
Therefore, introduce '__fix_address', which is the combination of
'__noclone' and 'noinline', and apply it to kfree_skb_reason() to
prevent to from being splited or made inline.
(Is it better to simply apply '__noclone oninline' to kfree_skb_reason?
I'm thinking maybe other functions have the same problems)
Meanwhile, wrap 'skb_unref()' with 'unlikely()', as the compiler thinks
it is likely return true and splits kfree_skb_reason().
Signed-off-by: Menglong Dong <imagedong@tencent.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add initial runtime info that we can copy to runtime info at i915
creation time. This lets us define the initial values for runtime info
statically while making it possible to change them runtime. This will be
the new home for the current "const" device info members that are
modified runtime anyway.
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Maarten Lankhort <maarten.lankhorst@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/a77c6db2da20d401f47a0a5e87356b9b3f6292df.1660910433.git.jani.nikula@intel.com
variable 'mode' is used uninitialized whenever switch default is taken
in sps.c which leads to the following clang warning.
drivers/platform/x86/amd/pmf/sps.c:96:2: error: variable 'mode' is used uninitialized whenever switch default is taken [-Werror,-Wsometimes-uninitialized]
default:
^~~~~~~
drivers/platform/x86/amd/pmf/sps.c:101:9: note: uninitialized use occurs here
return mode;
^~~~
drivers/platform/x86/amd/pmf/sps.c:84:9: note: initialize the variable 'mode' to silence this warning
u8 mode;
^
= '\0'
1 error generated.
Fix it by returning -EOPNOTSUPP in default case and also change the return
type of the function amd_pmf_get_pprof_modes() to keep it similar like
other drivers which implement platform_profile.
Fixes: 4c71ae4144 ("platform/x86/amd/pmf: Add support SPS PMF feature")
Reported-by: Nathan Chancellor <nathan@kernel.org>
Reviewed-by: Nathan Chancellor <nathan@kernel.org>
Signed-off-by: Shyam Sundar S K <Shyam-sundar.S-k@amd.com>
Link: https://lore.kernel.org/r/20220822062917.4061503-1-Shyam-sundar.S-k@amd.com
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Its reported that amd-pmf driver when built with config which does not
have ACPI_PLATFORM_PROFILE set/enabled throws a undefined references to
symbols used.
ld: vmlinux.o: in function `amd_pmf_init_sps':
drivers/platform/x86/amd/pmf/sps.c:132: undefined reference to `platform_profile_register'
ld: vmlinux.o: in function `amd_pmf_deinit_sps':
drivers/platform/x86/amd/pmf/sps.c:142: undefined reference to `platform_profile_remove'
Fix it by adding a "select" to the Kconfig.
Fixes: da5ce22df5 ("platform/x86/amd/pmf: Add support for PMF core layer")
Reported-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Shyam Sundar S K <Shyam-sundar.S-k@amd.com>
Acked-by: Randy Dunlap <rdunlap@infradead.org> # build-tested
Link: https://lore.kernel.org/r/20220819083858.3987590-1-Shyam-sundar.S-k@amd.com
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
When running identity-mapped and depending on the kernel configuration,
it is possible that the compiler uses jump tables when generating code
for cc_platform_has().
This causes a boot failure because the jump table uses un-mapped kernel
virtual addresses, not identity-mapped addresses. This has been seen
with CONFIG_RETPOLINE=n.
Similar to sme_encrypt_kernel(), use an open-coded direct check for the
status of SNP rather than trying to eliminate the jump table. This
preserves any code optimization in cc_platform_has() that can be useful
post boot. It also limits the changes to SEV-specific files so that
future compiler features won't necessarily require possible build changes
just because they are not compatible with running identity-mapped.
[ bp: Massage commit message. ]
Fixes: 5e5ccff60a ("x86/sev: Add helper for validating pages in early enc attribute changes")
Reported-by: Sean Christopherson <seanjc@google.com>
Suggested-by: Sean Christopherson <seanjc@google.com>
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Cc: <stable@vger.kernel.org> # 5.19.x
Link: https://lore.kernel.org/all/YqfabnTRxFSM+LoX@google.com/
In some cases, bootloaders will leave boot_params->cc_blob_address
uninitialized rather than zeroing it out. This field is only meant to be
set by the boot/compressed kernel in order to pass information to the
uncompressed kernel when SEV-SNP support is enabled.
Therefore, there are no cases where the bootloader-provided values
should be treated as anything other than garbage. Otherwise, the
uncompressed kernel may attempt to access this bogus address, leading to
a crash during early boot.
Normally, sanitize_boot_params() would be used to clear out such fields
but that happens too late: sev_enable() may have already initialized
it to a valid value that should not be zeroed out. Instead, have
sev_enable() zero it out unconditionally beforehand.
Also ensure this happens for !CONFIG_AMD_MEM_ENCRYPT as well by also
including this handling in the sev_enable() stub function.
[ bp: Massage commit message and comments. ]
Fixes: b190a043c4 ("x86/sev: Add SEV-SNP feature detection/setup")
Reported-by: Jeremi Piotrowski <jpiotrowski@linux.microsoft.com>
Reported-by: watnuss@gmx.de
Signed-off-by: Michael Roth <michael.roth@amd.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Cc: stable@vger.kernel.org
Link: https://bugzilla.kernel.org/show_bug.cgi?id=216387
Link: https://lore.kernel.org/r/20220823160734.89036-1-michael.roth@amd.com
Commit 368d179adb ("drm/i915/guc: Add GuC <-> kernel time stamp
translation information") added intel_device_info_print_runtime() in the
time info dump for no obvious reason or explanation in the commit
message. It only logs the rawclk freq. Remove it.
Cc: John Harrison <John.C.Harrison@Intel.com>
Cc: Alan Previn <alan.previn.teres.alexis@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: John Harrison <John.C.Harrison@Intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/b395ac4c909042f5daabf29959d8733993545aa2.1660910433.git.jani.nikula@intel.com
Currently, net.netfilter.nf_conntrack_frag6_high_thresh can only be lowered.
I found this issue while investigating a probable kernel issue
causing flakes in tools/testing/selftests/net/ip_defrag.sh
In particular, these sysctl changes were ignored:
ip netns exec "${NETNS}" sysctl -w net.netfilter.nf_conntrack_frag6_high_thresh=9000000 >/dev/null 2>&1
ip netns exec "${NETNS}" sysctl -w net.netfilter.nf_conntrack_frag6_low_thresh=7000000 >/dev/null 2>&1
This change is inline with commit 8361962392 ("net/ipfrag: let ip[6]frag_high_thresh
in ns be higher than in init_net")
Fixes: 8db3d41569bb ("netfilter: nf_defrag_ipv6: use net_generic infra")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
ALSA: Drop hackish GFP giveaway for CONTINUOUS pages
This is a series of cleanup patches for dropping the current hackish
way of passing the GFP_* flags for CONTINOUS and VMALLOC memory
allocations. There are only three users for this legacy feature, and
all of them seem superfluous. And, if any driver requires the memory
restriction in future, it can now pass the proper device pointer for
specifying the DMA mask.
Link: https://lore.kernel.org/r/20220823115740.14123-1-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
In order to ensure only documented properties are present, node schemas
must have unevaluatedProperties or additionalProperties set to false
(typically).
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Update the documentation to follow the recent change of the memory
allocation helpers. The macro snd_dma_continuous_data() is gone, and
the driver needs to set up the coherent dma mask for allocating in the
lower memory addresses, instead.
Link: https://lore.kernel.org/r/20220823115740.14123-6-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Now that all users of snd_dma_continuous_data() is gone, let's drop
this ugly (and dangerous) way.
After this commit, SNDRV_DMA_TYPE_CONTINUOUS may take the standard
device pointer instead of the hacked pointer by the macro above, and
the memalloc core refers to the coherent_dma_mask of the given
device like other SNDRV_DMA_TYPE. It's still allowed to pass NULL
there, and in that case, the allocation is performed always in the
normal zone.
For SNDRV_DMA_TYPE_VMALLOC, the device pointer is simply ignored.
Link: https://lore.kernel.org/r/20220823115740.14123-5-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
ASoC Atom SST driver is using the continuous RAM pages with GFP_DMA
flag for its PCM buffer, but this should work fine with the standard
DMA pages. As a part of cleanup work, this patch replaces the buffer
allocation to the standard device pages with SNDRV_DMA_TYPE_DEV.
Link: https://lore.kernel.org/r/20220823115740.14123-4-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Reviewed-by: Cezary Rojewski <cezary.rojewski@intel.com>