ASoC framework/driver checks whether card was instantiated every
where. Then, it should check card pointer too in such case.
This patch adds snd_soc_card_is_instantiated() for it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Reviewed-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://lore.kernel.org/r/875ycnfoqp.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>
snd_soc_dai_get_widget() requests SNDRV_PCM_STREAM_PLAYBACK/CAPTURE.
This patch adds helper for it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Reviewed-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://lore.kernel.org/r/877cx3foqz.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Current ASoC has tx/rx_mask, and is directly accessing to them,
but accessing to it via function is nice idea.
This patch adds snd_soc_dai_tdm_mask_set/get() for it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Reviewed-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://lore.kernel.org/r/878rhjfor8.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Current ASoC has snd_soc_dai_set/get_dma_data() which is assuming
struct snd_pcm_substream to get Playback/Capture direction.
But, many drivers want to use it not through snd_pcm_substream.
This patch adds more low level snd_soc_dai_dma_data_set/get() for it,
and previous functions will be macro for it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Reviewed-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://lore.kernel.org/r/87a61zfori.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Current ASoC has snd_soc_dai_get_widget() (= _get_) but doesn't
have _set_ function. This patch adds it.
This patch also cleanup unnecessary line break for _get_ function.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Reviewed-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://lore.kernel.org/r/87bkmfforp.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>
If a relocatable kernel is loaded at a non-zero address and told not to
relocate to zero (kdump or RELOCATABLE_TEST), the mapping of the
interrupt code at zero is left with RWX permissions.
That is a security weakness, and leads to a warning at boot if
CONFIG_DEBUG_WX is enabled:
powerpc/mm: Found insecure W+X mapping at address 00000000056435bc/0xc000000000000000
WARNING: CPU: 1 PID: 1 at arch/powerpc/mm/ptdump/ptdump.c:193 note_page+0x484/0x4c0
CPU: 1 PID: 1 Comm: swapper/0 Not tainted 6.2.0-rc1-00001-g8ae8e98aea82-dirty #175
Hardware name: IBM pSeries (emulated by qemu) POWER9 (raw) 0x4e1202 0xf000005 of:SLOF,git-dd0dca hv:linux,kvm pSeries
NIP: c0000000004a1c34 LR: c0000000004a1c30 CTR: 0000000000000000
REGS: c000000003503770 TRAP: 0700 Not tainted (6.2.0-rc1-00001-g8ae8e98aea82-dirty)
MSR: 8000000002029033 <SF,VEC,EE,ME,IR,DR,RI,LE> CR: 24000220 XER: 00000000
CFAR: c000000000545a58 IRQMASK: 0
...
NIP note_page+0x484/0x4c0
LR note_page+0x480/0x4c0
Call Trace:
note_page+0x480/0x4c0 (unreliable)
ptdump_pmd_entry+0xc8/0x100
walk_pgd_range+0x618/0xab0
walk_page_range_novma+0x74/0xc0
ptdump_walk_pgd+0x98/0x170
ptdump_check_wx+0x94/0x100
mark_rodata_ro+0x30/0x70
kernel_init+0x78/0x1a0
ret_from_kernel_thread+0x5c/0x64
The fix has two parts. Firstly the pages from zero up to the end of
interrupts need to be marked read-only, so that they are left with R-X
permissions. Secondly the mapping logic needs to be taught to ensure
there is a page boundary at the end of the interrupt region, so that the
permission change only applies to the interrupt text, and not the region
following it.
Fixes: c55d7b5e64 ("powerpc: Remove STRICT_KERNEL_RWX incompatibility with RELOCATABLE")
Reported-by: Sachin Sant <sachinp@linux.ibm.com>
Tested-by: Sachin Sant <sachinp@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20230110124753.1325426-2-mpe@ellerman.id.au
If a relocatable kernel is loaded at an address that is not 2MB aligned
and told not to relocate to zero, the kernel can crash due to
mark_rodata_ro() incorrectly changing some read-write data to read-only.
Scenarios where the misalignment can occur are when the kernel is
loaded by kdump or using the RELOCATABLE_TEST config option.
Example crash with the kernel loaded at 5MB:
Run /sbin/init as init process
BUG: Unable to handle kernel data access on write at 0xc000000000452000
Faulting instruction address: 0xc0000000005b6730
Oops: Kernel access of bad area, sig: 11 [#1]
LE PAGE_SIZE=64K MMU=Radix SMP NR_CPUS=2048 NUMA pSeries
CPU: 1 PID: 1 Comm: init Not tainted 6.2.0-rc1-00011-g349188be4841 #166
Hardware name: IBM pSeries (emulated by qemu) POWER9 (raw) 0x4e1202 0xf000005 of:SLOF,git-5b4c5a hv:linux,kvm pSeries
NIP: c0000000005b6730 LR: c000000000ae9ab8 CTR: 0000000000000380
REGS: c000000004503250 TRAP: 0300 Not tainted (6.2.0-rc1-00011-g349188be4841)
MSR: 8000000000009033 <SF,EE,ME,IR,DR,RI,LE> CR: 44288480 XER: 00000000
CFAR: c0000000005b66ec DAR: c000000000452000 DSISR: 0a000000 IRQMASK: 0
...
NIP memset+0x68/0x104
LR zero_user_segments.constprop.0+0xa8/0xf0
Call Trace:
ext4_mpage_readpages+0x7f8/0x830
ext4_readahead+0x48/0x60
read_pages+0xb8/0x380
page_cache_ra_unbounded+0x19c/0x250
filemap_fault+0x58c/0xae0
__do_fault+0x60/0x100
__handle_mm_fault+0x1230/0x1a40
handle_mm_fault+0x120/0x300
___do_page_fault+0x20c/0xa80
do_page_fault+0x30/0xc0
data_access_common_virt+0x210/0x220
This happens because mark_rodata_ro() tries to change permissions on the
range _stext..__end_rodata, but _stext sits in the middle of the 2MB
page from 4MB to 6MB:
radix-mmu: Mapped 0x0000000000000000-0x0000000000200000 with 2.00 MiB pages (exec)
radix-mmu: Mapped 0x0000000000200000-0x0000000000400000 with 2.00 MiB pages
radix-mmu: Mapped 0x0000000000400000-0x0000000002400000 with 2.00 MiB pages (exec)
The logic that changes the permissions assumes the linear mapping was
split correctly at boot, so it marks the entire 2MB page read-only. That
leads to the write fault above.
To fix it, the boot time mapping logic needs to consider that if the
kernel is running at a non-zero address then _stext is a boundary where
it must split the mapping.
That leads to the mapping being split correctly, allowing the rodata
permission change to take happen correctly, with no spillover:
radix-mmu: Mapped 0x0000000000000000-0x0000000000200000 with 2.00 MiB pages (exec)
radix-mmu: Mapped 0x0000000000200000-0x0000000000400000 with 2.00 MiB pages
radix-mmu: Mapped 0x0000000000400000-0x0000000000500000 with 64.0 KiB pages
radix-mmu: Mapped 0x0000000000500000-0x0000000000600000 with 64.0 KiB pages (exec)
radix-mmu: Mapped 0x0000000000600000-0x0000000002400000 with 2.00 MiB pages (exec)
If the kernel is loaded at a 2MB aligned address, the mapping continues
to use 2MB pages as before:
radix-mmu: Mapped 0x0000000000000000-0x0000000000200000 with 2.00 MiB pages (exec)
radix-mmu: Mapped 0x0000000000200000-0x0000000000400000 with 2.00 MiB pages
radix-mmu: Mapped 0x0000000000400000-0x0000000002c00000 with 2.00 MiB pages (exec)
radix-mmu: Mapped 0x0000000002c00000-0x0000000100000000 with 2.00 MiB pages
Fixes: c55d7b5e64 ("powerpc: Remove STRICT_KERNEL_RWX incompatibility with RELOCATABLE")
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20230110124753.1325426-1-mpe@ellerman.id.au
In kexec_extra_fdt_size_ppc64() there's logic to estimate how much
extra space will be needed in the device tree for some memory related
properties.
That logic uses the size of RAM divided by drmem_lmb_size() to do the
estimation. However drmem_lmb_size() can be zero if the machine has no
hotpluggable memory configured, which is the case when booting with qemu
and no maxmem=x parameter is passed (the default).
The division by zero is reported by UBSAN, and can also lead to an
overflow and a warning from kvmalloc, and kdump kernel loading fails:
WARNING: CPU: 0 PID: 133 at mm/util.c:596 kvmalloc_node+0x15c/0x160
Modules linked in:
CPU: 0 PID: 133 Comm: kexec Not tainted 6.2.0-rc5-03455-g07358bd97810 #223
Hardware name: IBM pSeries (emulated by qemu) POWER9 (raw) 0x4e1200 0xf000005 of:SLOF,git-dd0dca pSeries
NIP: c00000000041ff4c LR: c00000000041fe58 CTR: 0000000000000000
REGS: c0000000096ef750 TRAP: 0700 Not tainted (6.2.0-rc5-03455-g07358bd97810)
MSR: 800000000282b033 <SF,VEC,VSX,EE,FP,ME,IR,DR,RI,LE> CR: 24248242 XER: 2004011e
CFAR: c00000000041fed0 IRQMASK: 0
...
NIP kvmalloc_node+0x15c/0x160
LR kvmalloc_node+0x68/0x160
Call Trace:
kvmalloc_node+0x68/0x160 (unreliable)
of_kexec_alloc_and_setup_fdt+0xb8/0x7d0
elf64_load+0x25c/0x4a0
kexec_image_load_default+0x58/0x80
sys_kexec_file_load+0x5c0/0x920
system_call_exception+0x128/0x330
system_call_vectored_common+0x15c/0x2ec
To fix it, skip the calculation if drmem_lmb_size() is zero.
Fixes: 2377c92e37 ("powerpc/kexec_file: fix FDT size estimation for kdump kernel")
Cc: stable@vger.kernel.org # v5.12+
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20230130014707.541110-1-mpe@ellerman.id.au
While in theory the timer can be triggered before expires + delta, for the
cases of RT tasks they really have no business giving any lenience for
extra slack time, so override any passed value by the user and always use
zero for schedule_hrtimeout_range() calls. Furthermore, this is similar to
what the nanosleep(2) family already does with current->timer_slack_ns.
Signed-off-by: Davidlohr Bueso <dave@stgolabs.net>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lore.kernel.org/r/20230123173206.6764-3-dave@stgolabs.net
Commit 6a7ee50f8f ("ARM: disallow pre-ARMv5 builds with ld.lld")
prevented v4 or v4t kernels when ld.lld will link the kernel due to
inserting unsupported blx instructions.
ld.lld has been fixed in current main (16.0.0) to avoid inserting these
instructions by inserting position independent thunks instead. Allow
these configurations to be enabled when ld.lld 16.0.0 is used to link
the kernel.
Additionally, add a link to the upstream LLVM issue so that the reason
for this dependency is clearly documented.
Link: https://github.com/ClangBuiltLinux/linux/issues/964
Link: 6f9ff1beee
Suggested-by: Nick Desaulniers <ndesaulniers@google.com>
Tested-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Nathan Chancellor <nathan@kernel.org>
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Fix spelling (reported by codespell) and grammar in Arm Kconfig files.
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: linux-arm-kernel@lists.infradead.org
Cc: patches@armlinux.org.uk
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Replace a switch-case in rtw_write_port with an if statement and make the
code a bit shorter.
Signed-off-by: Martin Kaiser <martin@kaiser.cx>
Link: https://lore.kernel.org/r/20230130195303.138941-10-martin@kaiser.cx
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
legacy_dz in struct sta_xmit_priv is initialised but not used. It can be
removed.
Signed-off-by: Martin Kaiser <martin@kaiser.cx>
Link: https://lore.kernel.org/r/20230130195303.138941-7-martin@kaiser.cx
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
rtw_free_xmitframe_list iterates over the list of xmit_frames and frees
each entry. We can use list_for_each_entry_safe instead of coding this
manually. We need the _safe version as the current pxmitframe will be
removed from the list by rtw_free_xmitframe.
Signed-off-by: Martin Kaiser <martin@kaiser.cx>
Link: https://lore.kernel.org/r/20230130195303.138941-6-martin@kaiser.cx
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We can now change sta_pending in struct tx_servq from __queue to
list_head. The driver defines __queue as list_head + spinlock, the
spinlock is not used for sta_pending.
Signed-off-by: Martin Kaiser <martin@kaiser.cx>
Link: https://lore.kernel.org/r/20230130195303.138941-5-martin@kaiser.cx
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Modify the rtw_free_xmitframe_queue function to take a list_head pointer
instead of a __queue pointer.
This is an intermediate step towards changing struct tx_servq's
sta_pending from __queue to list_head.
Now that the function takes a list instead of a queue, we should also
rename it to rtw_free_xmitframe_list.
Signed-off-by: Martin Kaiser <martin@kaiser.cx>
Link: https://lore.kernel.org/r/20230130195303.138941-4-martin@kaiser.cx
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Modify the dequeue_xmitframes_to_sleeping_queue function to take a
list_head pointer instead of a __queue pointer.
This is an intermediate step towards changing struct tx_servq's
sta_pending from __queue to list_head.
Signed-off-by: Martin Kaiser <martin@kaiser.cx>
Link: https://lore.kernel.org/r/20230130195303.138941-3-martin@kaiser.cx
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There's no need for a spinlock in rtw_free_xmitframe_queue.
This function is called only from rtw_free_stainfo. rtw_free_stainfo holds
pxmitpriv->lock during all rtw_free_xmitframe_queue calls.
Signed-off-by: Martin Kaiser <martin@kaiser.cx>
Link: https://lore.kernel.org/r/20230130195303.138941-2-martin@kaiser.cx
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
rxSNRdB is initialized and set but never read. Remove dead code. Local
variable rx_snrX is then of no use. Remove rx_snrX as well. Local
variable tmp_rxsnr is then of no use. Remove tmp_rxsnr as well.
Signed-off-by: Philipp Hortmann <philipp.g.hortmann@gmail.com>
Link: https://lore.kernel.org/r/b3150d506556375c4b155c51eabf79e128f50780.1675003608.git.philipp.g.hortmann@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Rename constant TxBBGainTableLength to TX_BB_GAIN_TABLE_LEN,
CCKTxBBGainTableLength to CCK_TX_BB_GAIN_TABLE_LEN and
RT_CID_819x_Netcore to RT_CID_819X_NETCORE to avoid CamelCase which is
not accepted by checkpatch. Added spaces before and after "-" to fix
checkpatch message.
Signed-off-by: Philipp Hortmann <philipp.g.hortmann@gmail.com>
Link: https://lore.kernel.org/r/0f390222d1bd272c3e63d1b2936109ac50e9f05f.1675003608.git.philipp.g.hortmann@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
As DMA Rx can be completed from two places, it is possible that DMA Rx
completes before DMA completion callback had a chance to complete it.
Once the previous DMA Rx has been completed, a new one can be started
on the next UART interrupt. The following race is possible
(uart_unlock_and_check_sysrq_irqrestore() replaced with
spin_unlock_irqrestore() for simplicity/clarity):
CPU0 CPU1
dma_rx_complete()
serial8250_handle_irq()
spin_lock_irqsave(&port->lock)
handle_rx_dma()
serial8250_rx_dma_flush()
__dma_rx_complete()
dma->rx_running = 0
// Complete DMA Rx
spin_unlock_irqrestore(&port->lock)
serial8250_handle_irq()
spin_lock_irqsave(&port->lock)
handle_rx_dma()
serial8250_rx_dma()
dma->rx_running = 1
// Setup a new DMA Rx
spin_unlock_irqrestore(&port->lock)
spin_lock_irqsave(&port->lock)
// sees dma->rx_running = 1
__dma_rx_complete()
dma->rx_running = 0
// Incorrectly complete
// running DMA Rx
This race seems somewhat theoretical to occur for real but handle it
correctly regardless. Check what is the DMA status before complething
anything in __dma_rx_complete().
Reported-by: Gilles BULOZ <gilles.buloz@kontron.com>
Tested-by: Gilles BULOZ <gilles.buloz@kontron.com>
Fixes: 9ee4b83e51 ("serial: 8250: Add support for dmaengine")
Cc: stable@vger.kernel.org
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20230130114841.25749-3-ilpo.jarvinen@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
__dma_rx_complete() is called from two places:
- Through the DMA completion callback dma_rx_complete()
- From serial8250_rx_dma_flush() after IIR_RLSI or IIR_RX_TIMEOUT
The former does not hold port's lock during __dma_rx_complete() which
allows these two to race and potentially insert the same data twice.
Extend port's lock coverage in dma_rx_complete() to prevent the race
and check if the DMA Rx is still pending completion before calling
into __dma_rx_complete().
Reported-by: Gilles BULOZ <gilles.buloz@kontron.com>
Tested-by: Gilles BULOZ <gilles.buloz@kontron.com>
Fixes: 9ee4b83e51 ("serial: 8250: Add support for dmaengine")
Cc: stable@vger.kernel.org
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20230130114841.25749-2-ilpo.jarvinen@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Requesting an interrupt with IRQF_ONESHOT will run the primary handler
in the hard-IRQ context even in the force-threaded mode. The
force-threaded mode is used by PREEMPT_RT in order to avoid acquiring
sleeping locks (spinlock_t) in hard-IRQ context. This combination
makes it impossible and leads to "sleeping while atomic" warnings.
Use one interrupt handler for both handlers (primary and secondary)
and drop the IRQF_ONESHOT flag which is not needed.
Fixes: e359b4411c ("serial: stm32: fix threaded interrupt handling")
Reviewed-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Tested-by: Valentin Caron <valentin.caron@foss.st.com> # V3
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20230120160332.57930-1-marex@denx.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The 'aspeed,lpc-io-reg' property is also defined in
ipmi/aspeed,ast2400-kcs-bmc.yaml as a 'uint32-array'. Unify it to use
'uint32-array' everywhere.
Signed-off-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20230125221513.3059177-1-robh@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The struct liteuart_port keeps tracking of UART ID which is also
saved in the struct uart_port as line member. Drop the former one
and use the latter everywhere.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Gabriel Somlo <gsomlo@gmail.com>
Link: https://lore.kernel.org/r/20230123192604.81452-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In the probe we need to call all devm_*() first followed by
non-devm_*() calls. This is due to reversed clean up that
may happen in a wrong order otherwise. The driver currently
allocates xarray before calling
devm_platform_get_and_ioremap_resource(). While it's not an
issue in this certain case, it's still better to be pedantic.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Gabriel Somlo <somlo@cmu.edu>
Link: https://lore.kernel.org/r/20230123191741.79751-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The lpuart of imx8ulp is basically the same as imx7ulp, but it supports
some new features based on imx7ulp, such as it can assert the DMA
request on EOP(end-of-packet).
Here add lpuart support for imx8ulp, and rx_watermark is set to 3 as
imx8ulp RX FIFO depth is 8.
Signed-off-by: Sherry Sun <sherry.sun@nxp.com>
Link: https://lore.kernel.org/r/20230130064449.9564-7-sherry.sun@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add RTS watermark support for LPUART. The RX RTS_B output negates when
the number of empty words in the receive FIFO is greater or equal to
RTSWATER. Here set the RTSWATER to half of the rxfifo_size.
Signed-off-by: Sherry Sun <sherry.sun@nxp.com>
Link: https://lore.kernel.org/r/20230130064449.9564-6-sherry.sun@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
With the growth of rx watermark, it's useful to enable the Receiver Idle
Empty function, it can assert the RDRF(Receive Data Register Full Flag)
when the receiver is idle for a number of idle characters and the FIFO
is not empty. It will generate a DMA request or interrupt, which can
avoid receive data being trapped in the RX FIFO since the number of
words received is less than the watermark.
Here set the RXIDEN as 0x3 which enable the RDRF assertion due to
partially filled FIFO when receiver is idle for 4 characters.
Signed-off-by: Sherry Sun <sherry.sun@nxp.com>
Link: https://lore.kernel.org/r/20230130064449.9564-5-sherry.sun@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The RXWATER value must be greater than 0 according to the LPUART
reference manual. And when the number of datawords in the receive
FIFO is greater than RXWATER, an interrupt or a DMA request is
generated, so no need to set the different value for lpuart interrupt
case and dma case. Here delete the wrong RXWATER setting for dma case
directly.
Fixes: 42b68768e5 ("serial: fsl_lpuart: DMA support for 32-bit variant")
Signed-off-by: Sherry Sun <sherry.sun@nxp.com>
Link: https://lore.kernel.org/r/20230130064449.9564-4-sherry.sun@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since imx8qxp RX FIFO depth is 64 datawords, it will be better to set
the rx watermark as 31, which means when the number of datawords in the
receive FIFO(>= 32) is greater than the watermark, an interrupt or a DMA
request is generated.
Also keep the console rx watermark as 1 to make sure it responsive.
Signed-off-by: Sherry Sun <sherry.sun@nxp.com>
Link: https://lore.kernel.org/r/20230130064449.9564-3-sherry.sun@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add rx_watermark parameter for struct lpuart_port to make the receive
watermark configurable for different platforms.
No function changed.
Signed-off-by: Sherry Sun <sherry.sun@nxp.com>
Link: https://lore.kernel.org/r/20230130064449.9564-2-sherry.sun@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
lpuart32_setup_watermark_enable() will configure the UART FIFO and
watermark, also enable the receiver and transmitter, this should be done
after the rx/tx dma steup ready.
Also add lpuart32_hw_disable() to make sure the receiver/transmitter and
interrupts are disabled during the dma steup.
Signed-off-by: Sherry Sun <sherry.sun@nxp.com>
Link: https://lore.kernel.org/r/20230130054107.9119-1-sherry.sun@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The usual mixed bag - with a bunch of issues found by Carlos Song
in the fxos8700 IMU driver dominating.
hid-accel,gyro
- Fix wrong returned value when read succeeds.
marvell,berlin-adc
- Missing of_node_put() in an error path.
nxp,fxos8700 (freescale)
- Wrong channel type match.
- Swapped channel read back.
- Incomplete channel read back (not enough bytes).
- Missing shift of acceleration data.
- Range selection didn't work (datasheet bug)
- Wrong ODR mode read back due to wrong field offset.
- Drop unused, but wrong define.
- Fix issue with magnetometer scale an units.
nxp,imx8qxp
- Fix an irq flood due to not reading data early enough.
st,lsm6dsx
- Add CONFIG_IIO_TRIGGERED_BUFFER select.
st,stm32-adc
- Fix missing MODULE_DEVICE_TABLE() needed for module aliases.
ti,twl6030
- Fix missing enable of some channels.
- Fix a typo in previous patch that meant one channel still wasn't enabled.
xilinx,xadc
- Carrying on incorrectly after allocation error.
-----BEGIN PGP SIGNATURE-----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=OFFy
-----END PGP SIGNATURE-----
Merge tag 'iio-fixes-for-6.2a' of https://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into char-misc-next
Jonathan writes:
"1st set of IIO fixes for the 6.2 cycle.
The usual mixed bag - with a bunch of issues found by Carlos Song
in the fxos8700 IMU driver dominating.
hid-accel,gyro
- Fix wrong returned value when read succeeds.
marvell,berlin-adc
- Missing of_node_put() in an error path.
nxp,fxos8700 (freescale)
- Wrong channel type match.
- Swapped channel read back.
- Incomplete channel read back (not enough bytes).
- Missing shift of acceleration data.
- Range selection didn't work (datasheet bug)
- Wrong ODR mode read back due to wrong field offset.
- Drop unused, but wrong define.
- Fix issue with magnetometer scale an units.
nxp,imx8qxp
- Fix an irq flood due to not reading data early enough.
st,lsm6dsx
- Add CONFIG_IIO_TRIGGERED_BUFFER select.
st,stm32-adc
- Fix missing MODULE_DEVICE_TABLE() needed for module aliases.
ti,twl6030
- Fix missing enable of some channels.
- Fix a typo in previous patch that meant one channel still wasn't enabled.
xilinx,xadc
- Carrying on incorrectly after allocation error."
* tag 'iio-fixes-for-6.2a' of https://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio:
iio: imu: fxos8700: fix MAGN sensor scale and unit
iio: imu: fxos8700: remove definition FXOS8700_CTRL_ODR_MIN
iio: imu: fxos8700: fix failed initialization ODR mode assignment
iio: imu: fxos8700: fix incorrect ODR mode readback
iio: light: cm32181: Fix PM support on system with 2 I2C resources
iio: hid: fix the retval in gyro_3d_capture_sample
iio: hid: fix the retval in accel_3d_capture_sample
iio: imu: st_lsm6dsx: fix build when CONFIG_IIO_TRIGGERED_BUFFER=m
iio:adc:twl6030: Enable measurement of VAC
iio: imu: fxos8700: fix ACCEL measurement range selection
iio: imu: fxos8700: fix IMU data bits returned to user space
iio: imu: fxos8700: fix incomplete ACCEL and MAGN channels readback
iio: imu: fxos8700: fix swapped ACCEL and MAGN channels readback
iio: imu: fxos8700: fix map label of channel type to MAGN sensor
iio:adc:twl6030: Enable measurements of VUSB, VBAT and others
iio: imx8qxp-adc: fix irq flood when call imx8qxp_adc_read_raw()
iio: adc: xilinx-ams: fix devm_krealloc() return value check
iio: adc: berlin2-adc: Add missing of_node_put() in error path
iio: adc: stm32-dfsdm: fill module aliases
