ACPICA commit 1dc530059a3e6202e941e6a9478cf30f092bfb47
loong_arch-specific interrupt controllers (similar to APIC) are added
in the next revision of ACPI Specification (current revision is 6.4),
which including CORE_PIC (CPUINTC), LIO_PIC (LIOINTC), EIO_PIC (EIOINTC),
HT_PIC (HTVECINTC), BIO_PIC (PCHINTC), LPC_PIC (PCHLPC) and MSI_PIC
(PCHMSI). This patch add their definition.
ACPI changes of loong_arch-specific interrupt controllers have already
been approved in the ECRs, and will be public in the next revision of
ACPI Specification.
Link: 1dc53005
Link: https://mantis.uefi.org/mantis/view.php?id=2203
Link: https://mantis.uefi.org/mantis/view.php?id=2313
Co-developed-by: Jianmin Lv <lvjianmin@loongson.cn>
Signed-off-by: Jianmin Lv <lvjianmin@loongson.cn>
Signed-off-by: Huacai Chen <chenhuacai@loongson.cn>
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The acpi_ex_load_op() code has slightly diverged from the upstream
implementation, so correct that to make the behavior consistent with
the upstream and avoid patch backporting issues going forward.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
When not all LED channels of the led chip are configured, the
sysfs selftest functionality gives erroneous results and tries to
test all channels of the chip.
There is a potential for LED overcurrent conditions since the
test current will be set to values from out-of-bound regions.
It is wrong to use pdata->led_config[i].led_current to skip absent
channels as led_config[] only contains the configured LED channels.
Instead of iterating over all the physical channels of the device,
loop over the available LED configurations and use led->chan_nr to
access the correct i2c registers. Keep the zero-check for the LED
current as existing users might depend on this to disable a channel.
Reported-by: Arne Staessen <a.staessen@televic.com>
Signed-off-by: Maarten Zanders <maarten.zanders@mind.be>
Signed-off-by: Pavel Machek <pavel@ucw.cz>
After some off-list discussion with Marek Vasut and Geert Uytterhoeven
and finally a kx022a driver related discussion with Joe Perches
https://lore.kernel.org/lkml/92c3f72e60bc99bf4a21da259b4d78c1bdca447d.camel@perches.com/
it seems that my status as a reviewer has been wrong. I do look after
the ROHM/Kionix drivers I've authored and currently I am also paid to do
so as is reflected by the 'S: Supported'. According to Joe, the reviewer
entry in MAINTAINERS do not indicate such level of support and having a
reviewer supporting an IC is a contradiction.
Switch undersigned from a reviewer to a maintainer for IC drivers I am
taking care of.
Signed-off-by: Matti Vaittinen <mazziesaccount@gmail.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Merge an IRQ override quirk, an ACPI PCC code fix and a device
properties documentation update for 6.1-rc3:
- Make the ACPI device resources code skip IRQ override on Asus
Vivobook S5602ZA (Tamim Khan).
- Fix a possible integer overflow during multiplication in the ACPI
PCC code (Manank Patel).
- Fix the documentation of the *_match_string() family of functions to
properly cover the return value (Andy Shevchenko).
* acpi-resource:
ACPI: resource: Skip IRQ override on Asus Vivobook S5602ZA
* acpi-pcc:
ACPI: PCC: Fix unintentional integer overflow
* devprop:
device property: Fix documentation for *_match_string() APIs
Merge a hiberantion-related fix, a generic power domains code fix and
a pm-graph update for 6.1-rc1:
- Allow hybrid sleep to use suspend-to-idle as a system suspend method
if it is the current suspend method of choice (Mario Limonciello).
- Fix handling of unavailable/disabled idle states in the generic
power domains code (Sudeep Holla).
- Update the pm-graph suite of utilities to version 5.10 which is
fixes-mostly and does not add any new features (Todd Brandt).
* pm-sleep:
PM: hibernate: Allow hybrid sleep to work with s2idle
* pm-domains:
PM: domains: Fix handling of unavailable/disabled idle states
* pm-tools:
pm-graph v5.10
adv7511 probe may need to be attempted multiple times before no
-EPROBE_DEFER is returned. Currently, every such probe results in
an error message:
[ 4.534229] adv7511 1-003d: failed to find dsi host
[ 4.580288] adv7511 1-003d: failed to find dsi host
This is misleading, as there is no error and probe deferral is normal
behavior. Fix this by using dev_err_probe that will suppress
-EPROBE_DEFER errors. While at it, we touch all dev_err in the probe
path. This makes the code more concise and included the error code
everywhere to aid user in debugging.
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Ahmad Fatoum <a.fatoum@pengutronix.de>
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20221026125246.3188260-1-a.fatoum@pengutronix.de
Function blk_mq_alloc_request_hctx() is missing zeroing/init of rq->bio,
biotail, __sector, and __data_len members, which blk_mq_alloc_request()
has, so duplicate what we do in blk_mq_alloc_request().
Fixes: 1f5bd336b9 ("blk-mq: add blk_mq_alloc_request_hctx")
Signed-off-by: John Garry <john.garry@huawei.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Ming Lei <ming.lei@redhat.com>
Link: https://lore.kernel.org/r/1666780513-121650-1-git-send-email-john.garry@huawei.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Add common schema for restart and shutdown handlers, so they all use
same meaning of "priority" field. The Linux drivers already have this
property and some systems want to customize it per-board in DTS.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Don't populate the read-only array name on the stack but instead make
it static. Since the data and the pointers don't change also add in
a missing const. Also makes the object code a little smaller.
Signed-off-by: Colin Ian King <colin.i.king@gmail.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
When evm_status is INTEGRITY_PASS then this function returns early and so
later codepaths that check for evm_status != INTEGRITY_PASS can be removed
as they are dead code.
Fixes: e61b135f7b ("integrity: implement get and set acl hook")
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Christian Brauner (Microsoft) <brauner@kernel.org>
During firmware recovery, the monitor interface is not
getting created in the driver and firmware since
the respective flags are not updated properly.
So after firmware recovery is successful, when monitor
interface is brought down manually, firmware assertion
is observed, since we are trying to bring down the
interface which is not yet created in the firmware.
Fix this by updating the monitor flags properly per
phy#, during firmware recovery.
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.7.0.1-01744-QCAHKSWPL_SILICONZ-1
Signed-off-by: Nagarajan Maran <quic_nmaran@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20221014155054.11471-1-quic_nmaran@quicinc.com
Commit b9e8a7d950 ("firmware: ti_sci: Switch transport to polled
mode during system suspend") uses read_poll_timeout_atomic() macro
in ti_sci_do_xfer() to wait for completion when the system is
suspending. The break condition of the macro is set to "true" which
will cause it break immediately when evaluated, likely before the
TISCI xfer is completed, and always return 0. We want to poll here
until "done_state == true".
1) Change the break condition of read_poll_timeout_atomic() to
the bool variable "done_state".
2) The read_poll_timeout_atomic() returns 0 if the break condition
is met or -ETIMEDOUT if not. Since our break condition has changed
to "done_state", we also don't have to check for "!done_state" when
evaluating the return value.
Fixes: b9e8a7d950 ("firmware: ti_sci: Switch transport to polled mode during system suspend")
Signed-off-by: Georgi Vlaev <g-vlaev@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Link: https://lore.kernel.org/r/20221021185704.181316-1-g-vlaev@ti.com
There is a sparse warning shown below:
drivers/soc/ti/knav_qmss_queue.c:70:12: warning: symbol
'knav_acc_firmwares' was not declared. Should it be static?
Since 'knav_acc_firmwares' is only called within knav_qmss_queue.c,
mark it as static to fix the warning.
Fixes: 96ee19becc ("soc: ti: add firmware file name as part of the driver")
Signed-off-by: Chen Jiahao <chenjiahao16@huawei.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Link: https://lore.kernel.org/r/20221019153212.72350-1-chenjiahao16@huawei.com
I2C nodes defined in the top-level J721s2 SoC dtsi files are incomplete
and will not be functional unless they are extended with pinmux
information.
As the pinmux is only known at the board integration level, these
nodes should only be enabled when provided with this information.
Disable the I2C nodes in the dtsi files and only enable the ones that
are actually pinned out on a given board.
Signed-off-by: Andrew Davis <afd@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Bryan Brattlof <bb@ti.com>
Link: https://lore.kernel.org/r/20221020160305.18711-13-afd@ti.com
MCAN nodes defined in the top-level J721s2 SoC dtsi files are incomplete
and may not be functional unless they are extended with pinmux
information.
As the pinmux is only known at the board integration level, these
nodes should only be enabled when provided with this information.
Disable the MCAN nodes in the dtsi files and only enable the ones that
are actually pinned out on a given board.
Signed-off-by: Andrew Davis <afd@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Bryan Brattlof <bb@ti.com>
Link: https://lore.kernel.org/r/20221020160305.18711-12-afd@ti.com
Mailbox nodes defined in the top-level J721s2 SoC dtsi files are incomplete
and may not be functional unless they are extended with a chosen interrupt
and connection to a remote processor.
As the remote processors depend on memory nodes which are only known at
the board integration level, these nodes should only be enabled when
provided with the above information.
Disable the Mailbox nodes in the dtsi files and only enable the ones that
are actually used on a given board.
Signed-off-by: Andrew Davis <afd@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Bryan Brattlof <bb@ti.com>
Link: https://lore.kernel.org/r/20221020160305.18711-11-afd@ti.com
Mailbox nodes defined in the top-level J7200 SoC dtsi files are incomplete
and may not be functional unless they are extended with a chosen interrupt
and connection to a remote processor.
As the remote processors depend on memory nodes which are only known at
the board integration level, these nodes should only be enabled when
provided with the above information.
Disable the Mailbox nodes in the dtsi files and only enable the ones that
are actually used on a given board.
Signed-off-by: Andrew Davis <afd@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Bryan Brattlof <bb@ti.com>
Link: https://lore.kernel.org/r/20221020160305.18711-10-afd@ti.com
Mailbox nodes defined in the top-level J721e SoC dtsi files are incomplete
and may not be functional unless they are extended with a chosen interrupt
and connection to a remote processor.
As the remote processors depend on memory nodes which are only known at
the board integration level, these nodes should only be enabled when
provided with the above information.
Disable the Mailbox nodes in the dtsi files and only enable the ones that
are actually used on a given board.
Signed-off-by: Andrew Davis <afd@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Bryan Brattlof <bb@ti.com>
Link: https://lore.kernel.org/r/20221020160305.18711-9-afd@ti.com
UART nodes defined in the top-level J721s2 SoC dtsi files are incomplete
and may not be functional unless they are extended with pinmux
information.
As the pinmux is only known at the board integration level, these
nodes should only be enabled when provided with this information.
Disable the UART nodes in the dtsi files and only enable the ones that
are actually pinned out on a given board.
Signed-off-by: Andrew Davis <afd@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Bryan Brattlof <bb@ti.com>
Link: https://lore.kernel.org/r/20221020160305.18711-8-afd@ti.com
I2C nodes defined in the top-level J7200 SoC dtsi files are incomplete
and will not be functional unless they are extended with pinmux
information.
As the pinmux is only known at the board integration level, these
nodes should only be enabled when provided with this information.
Disable the I2C nodes in the dtsi files and only enable the ones that
are actually pinned out on a given board.
Signed-off-by: Andrew Davis <afd@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Bryan Brattlof <bb@ti.com>
Link: https://lore.kernel.org/r/20221020160305.18711-7-afd@ti.com
UART nodes defined in the top-level J7200 SoC dtsi files are incomplete
and may not be functional unless they are extended with pinmux
information.
As the pinmux is only known at the board integration level, these
nodes should only be enabled when provided with this information.
Disable the UART nodes in the dtsi files and only enable the ones that
are actually pinned out on a given board.
Signed-off-by: Andrew Davis <afd@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Bryan Brattlof <bb@ti.com>
Link: https://lore.kernel.org/r/20221020160305.18711-6-afd@ti.com
MCAN nodes defined in the top-level J721e SoC dtsi files are incomplete
and may not be functional unless they are extended with pinmux
information.
As the pinmux is only known at the board integration level, these
nodes should only be enabled when provided with this information.
Disable the MCAN nodes in the dtsi files and only enable the ones that
are actually pinned out on a given board.
Signed-off-by: Andrew Davis <afd@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Bryan Brattlof <bb@ti.com>
Link: https://lore.kernel.org/r/20221020160305.18711-5-afd@ti.com
MCASP nodes defined in the top-level J721e SoC dtsi files are incomplete
and may not be functional unless they are extended with pinmux
information.
As the pinmux is only known at the board integration level, these
nodes should only be enabled when provided with this information.
Disable the MCASP nodes in the dtsi files and only enable the ones that
are actually pinned out on a given board.
Signed-off-by: Andrew Davis <afd@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Bryan Brattlof <bb@ti.com>
Link: https://lore.kernel.org/r/20221020160305.18711-4-afd@ti.com
I2C nodes defined in the top-level J721e SoC dtsi files are incomplete
and will not be functional unless they are extended with pinmux
information.
As the pinmux is only known at the board integration level, these
nodes should only be enabled when provided with this information.
Disable the I2C nodes in the dtsi files and only enable the ones that
are actually pinned out on a given board.
Signed-off-by: Andrew Davis <afd@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Bryan Brattlof <bb@ti.com>
Link: https://lore.kernel.org/r/20221020160305.18711-3-afd@ti.com
UART nodes defined in the top-level J721e SoC dtsi files are incomplete
and may not be functional unless they are extended with pinmux
information.
As the pinmux is only known at the board integration level, these
nodes should only be enabled when provided with this information.
Disable the UART nodes in the dtsi files and only enable the ones that
are actually pinned out on a given board.
Signed-off-by: Andrew Davis <afd@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Bryan Brattlof <bb@ti.com>
Link: https://lore.kernel.org/r/20221020160305.18711-2-afd@ti.com
OSPI nodes defined in the top-level AM62x SoC dtsi files are incomplete
and will not be functional unless they are extended with pinmux
information.
As the pinmux is only known at the board integration level, these
nodes should only be enabled when provided with this information.
Disable the OSPI nodes in the dtsi files and only enable the ones that
are actually pinned out on a given board.
Signed-off-by: Andrew Davis <afd@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Bryan Brattlof <bb@ti.com>
Link: https://lore.kernel.org/r/20221018211533.21335-11-afd@ti.com
SDHCI nodes defined in the top-level AM62x SoC dtsi files are incomplete
and will not be functional unless they are extended with pinmux
information.
As the pinmux is only known at the board integration level, these
nodes should only be enabled when provided with this information.
Disable the SDHCI nodes in the dtsi files and only enable the ones that
are actually pinned out on a given board.
Signed-off-by: Andrew Davis <afd@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Bryan Brattlof <bb@ti.com>
Link: https://lore.kernel.org/r/20221018211533.21335-10-afd@ti.com
MCAN nodes defined in the top-level AM62x SoC dtsi files are incomplete
and will not be functional unless they are extended with pinmux
information.
As the pinmux is only known at the board integration level, these
nodes should only be enabled when provided with this information.
Disable the MCAN nodes in the dtsi files and only enable the ones that
are actually pinned out on a given board.
Signed-off-by: Andrew Davis <afd@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Bryan Brattlof <bb@ti.com>
Link: https://lore.kernel.org/r/20221018211533.21335-9-afd@ti.com
MDIO nodes defined in the top-level AM62x SoC dtsi files are incomplete
and will not be functional unless they are extended with a pinmux.
As the attached PHY is only known about at the board integration level,
these nodes should only be enabled when provided with this information.
Disable the MDIO nodes in the dtsi files and only enable the ones that
are actually pinned out on a given board.
Signed-off-by: Andrew Davis <afd@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Bryan Brattlof <bb@ti.com>
Link: https://lore.kernel.org/r/20221018211533.21335-8-afd@ti.com
Although usually integrated as a child of an Ethernet controller, MDIO
IP has an independent pinout. This pinout should be controlled by
the MDIO node (so if it was to be disabled for instance, the pinmux
state would reflect that).
Move the MDIO pins pinmux to the MIDO nodes.
Signed-off-by: Andrew Davis <afd@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Bryan Brattlof <bb@ti.com>
Link: https://lore.kernel.org/r/20221018211533.21335-7-afd@ti.com
ECAP nodes defined in the top-level AM62x SoC dtsi files are incomplete
and will not be functional unless they are extended with pinmux
information. (These and the EPWM nodes could be used to trigger internal
actions but they are not used like that currently)
As the pinmux is only known at the board integration level, these
nodes should only be enabled when provided with this information.
Disable the ECAP nodes in the dtsi files and only enable the ones that
are actually pinned out on a given board.
Signed-off-by: Andrew Davis <afd@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Bryan Brattlof <bb@ti.com>
Link: https://lore.kernel.org/r/20221018211533.21335-6-afd@ti.com
EPWM nodes defined in the top-level AM62x SoC dtsi files are incomplete
and will not be functional unless they are extended with pinmux
information.
As the pinmux is only known at the board integration level, these
nodes should only be enabled when provided with this information.
Disable the EPWM nodes in the dtsi files and only enable the ones that
are actually pinned out on a given board.
Signed-off-by: Andrew Davis <afd@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Bryan Brattlof <bb@ti.com>
Link: https://lore.kernel.org/r/20221018211533.21335-5-afd@ti.com
SPI nodes defined in the top-level AM62x SoC dtsi files are incomplete
and will not be functional unless they are extended with pinmux
information.
As the pinmux is only known at the board integration level, these
nodes should only be enabled when provided with this information.
Disable the SPI nodes in the dtsi files and only enable the ones that
are actually pinned out on a given board.
Signed-off-by: Andrew Davis <afd@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Bryan Brattlof <bb@ti.com>
Link: https://lore.kernel.org/r/20221018211533.21335-4-afd@ti.com
I2C nodes defined in the top-level AM62x SoC dtsi files are incomplete
and will not be functional unless they are extended with pinmux
information.
As the pinmux is only known at the board integration level, these
nodes should only be enabled when provided with this information.
Disable the I2C nodes in the dtsi files and only enable the ones that
are actually pinned out on a given board.
Signed-off-by: Andrew Davis <afd@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Bryan Brattlof <bb@ti.com>
Link: https://lore.kernel.org/r/20221018211533.21335-3-afd@ti.com
UART nodes defined in the top-level AM62x SoC dtsi files are incomplete
and will not be functional unless they are extended with pinmux
information.
As the pinmux is only known at the board integration level, these
nodes should only be enabled when provided with this information.
Disable the UART nodes in the dtsi files and only enable the ones that
are actually pinned out on a given board.
Signed-off-by: Andrew Davis <afd@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Bryan Brattlof <bb@ti.com>
Link: https://lore.kernel.org/r/20221018211533.21335-2-afd@ti.com
The GPMC node defined in the top-level AM64x SoC dtsi files are incomplete
and will not be functional unless it is extended with pinmux information.
As the pinmux is only known at the board integration level, this node
should only be enabled when provided with this information.
Disable the GPMC node in the dtsi file. Since the ELM is made to work
with the GPMC, disable it too.
Signed-off-by: Andrew Davis <afd@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Bryan Brattlof <bb@ti.com>
Acked-by: Vignesh Raghavendra <vigneshr@ti.com>
Link: https://lore.kernel.org/r/20221017192532.23825-11-afd@ti.com
MCAN nodes defined in the top-level AM64x SoC dtsi files are incomplete
and will not be functional unless they are extended with pinmux
information.
As the pinmux is only known at the board integration level, these
nodes should only be enabled when provided with this information.
Disable the MCAN nodes in the dtsi files and only enable the ones that
are actually pinned out on a given board.
Signed-off-by: Andrew Davis <afd@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Bryan Brattlof <bb@ti.com>
Acked-by: Vignesh Raghavendra <vigneshr@ti.com>
Link: https://lore.kernel.org/r/20221017192532.23825-10-afd@ti.com
MDIO nodes defined in the top-level AM64x SoC dtsi files are incomplete
and will not be functional unless they are extended with a pinmux.
As the attached PHY is only known about at the board integration level,
these nodes should only be enabled when provided with this information.
Disable the MDIO nodes (in both CPSW and ICSSG) in the dtsi files and
only enable the ones that are actually pinned out on a given board.
Signed-off-by: Andrew Davis <afd@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Bryan Brattlof <bb@ti.com>
Acked-by: Vignesh Raghavendra <vigneshr@ti.com>
Link: https://lore.kernel.org/r/20221017192532.23825-9-afd@ti.com
Although usually integrated as a child of an Ethernet controller, MDIO
IP has an independent pinout. This pinout should be controlled by
the MDIO node (so if it was to be disabled for instance, the pinmux
state would reflect that).
Move the MDIO pins pinmux to the MIDO nodes.
Signed-off-by: Andrew Davis <afd@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Bryan Brattlof <bb@ti.com>
Acked-by: Vignesh Raghavendra <vigneshr@ti.com>
Link: https://lore.kernel.org/r/20221017192532.23825-8-afd@ti.com
PCIe nodes defined in the top-level AM64x SoC dtsi files are incomplete
and will not be functional unless they are extended with a SerDes PHY.
And usually only one of the two modes can be used at a time as they
share a SerDes link.
As the PHY and mode is only known at the board integration level, these
nodes should only be enabled when provided with this information.
Disable the PCIe nodes in the dtsi files and only enable the ones that
are actually pinned out on a given board.
Signed-off-by: Andrew Davis <afd@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Bryan Brattlof <bb@ti.com>
Acked-by: Vignesh Raghavendra <vigneshr@ti.com>
Link: https://lore.kernel.org/r/20221017192532.23825-7-afd@ti.com
ECAP nodes defined in the top-level AM64x SoC dtsi files are incomplete
and will not be functional unless they are extended with pinmux
information. (These and the EPWM nodes could be used to trigger internal
actions but they are not used like that currently)
As the pinmux is only known at the board integration level, these
nodes should only be enabled when provided with this information.
Disable the ECAP nodes in the dtsi files and only enable the ones that
are actually pinned out on a given board.
Signed-off-by: Andrew Davis <afd@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Bryan Brattlof <bb@ti.com>
Acked-by: Vignesh Raghavendra <vigneshr@ti.com>
Link: https://lore.kernel.org/r/20221017192532.23825-6-afd@ti.com
EPWM nodes defined in the top-level AM64x SoC dtsi files are incomplete
and will not be functional unless they are extended with pinmux
information.
As the pinmux is only known at the board integration level, these
nodes should only be enabled when provided with this information.
Disable the EPWM nodes in the dtsi files and only enable the ones that
are actually pinned out on a given board.
Signed-off-by: Andrew Davis <afd@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Bryan Brattlof <bb@ti.com>
Acked-by: Vignesh Raghavendra <vigneshr@ti.com>
Link: https://lore.kernel.org/r/20221017192532.23825-5-afd@ti.com
SPI nodes defined in the top-level AM64x SoC dtsi files are incomplete
and will not be functional unless they are extended with pinmux
information.
As the pinmux is only known at the board integration level, these
nodes should only be enabled when provided with this information.
Disable the SPI nodes in the dtsi files and only enable the ones that
are actually pinned out on a given board.
Signed-off-by: Andrew Davis <afd@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Bryan Brattlof <bb@ti.com>
Acked-by: Vignesh Raghavendra <vigneshr@ti.com>
Link: https://lore.kernel.org/r/20221017192532.23825-4-afd@ti.com
I2C nodes defined in the top-level AM64x SoC dtsi files are incomplete
and will not be functional unless they are extended with pinmux
information.
As the pinmux is only known at the board integration level, these
nodes should only be enabled when provided with this information.
Disable the I2C nodes in the dtsi files and only enable the ones that
are actually pinned out on a given board.
Signed-off-by: Andrew Davis <afd@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Bryan Brattlof <bb@ti.com>
Acked-by: Vignesh Raghavendra <vigneshr@ti.com>
Link: https://lore.kernel.org/r/20221017192532.23825-3-afd@ti.com
UART nodes defined in the top-level AM64x SoC dtsi files are incomplete
and will not be functional unless they are extended with pinmux
information.
As the pinmux is only known at the board integration level, these
nodes should only be enabled when provided with this information.
Disable the UART nodes in the dtsi files and only enable the ones that
are actually pinned out on a given board.
Signed-off-by: Andrew Davis <afd@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Bryan Brattlof <bb@ti.com>
Acked-by: Vignesh Raghavendra <vigneshr@ti.com>
Link: https://lore.kernel.org/r/20221017192532.23825-2-afd@ti.com
This Asus Zenbook laptop use Realtek HDA codec combined with
2xCS35L41 Amplifiers using I2C with Internal Boost.
Signed-off-by: Stefan Binding <sbinding@opensource.cirrus.com>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20221028102742.2588687-1-sbinding@opensource.cirrus.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
