[Why]
reuse struct rect rather than adding a new struct.
[How]
- Userspace keeps inputting x_start, y_start, x_end, y_end
- We translate data to x, y, width, height in code flow to store
- translate back to x_start, y_start, x_end, y_end before programming HW
Tested-by: Mark Broadworth <mark.broadworth@amd.com>
Reviewed-by: Wayne Lin <Wayne.Lin@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alan Liu <HaoPing.Liu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Porting secure display feature from DCN10 to DCN21. Support single
display for now and will extend to multiple displays.
[How]
- use workqueue to offload works for dmub or dmcu firmware
- after receiving ROI update from userspace, set skip_frame_cnt to 1
- refactor amdgpu_dm_crtc_handle_crc_window_irq()
- disable PSR before activating secure_display on a crtc
- check if secure_display is activated before enabling psr
- only work for single display for now.
Tested-by: Mark Broadworth <mark.broadworth@amd.com>
Reviewed-by: Wayne Lin <Wayne.Lin@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alan Liu <HaoPing.Liu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Ignore cable ID for DP2 receivers that does not support the feature.
Tested-by: Mark Broadworth <mark.broadworth@amd.com>
Reviewed-by: Roman Li <Roman.Li@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Fangzhi Zuo <Jerry.Zuo@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Under memory pressure, enetc_refill_rx_ring() may fail, and when called
during the enetc_open() -> enetc_setup_rxbdr() procedure, this is not
checked for.
An extreme case of memory pressure will result in exactly zero buffers
being allocated for the RX ring, and in such a case it is expected that
hardware drops all RX packets due to lack of buffers.
This does not happen, because the reset-default value of the consumer
and produces index is 0, and this makes the ENETC think that all buffers
have been initialized and that it owns them (when in reality none were).
The hardware guide explains this best:
| Configure the receive ring producer index register RBaPIR with a value
| of 0. The producer index is initially configured by software but owned
| by hardware after the ring has been enabled. Hardware increments the
| index when a frame is received which may consume one or more BDs.
| Hardware is not allowed to increment the producer index to match the
| consumer index since it is used to indicate an empty condition. The ring
| can hold at most RBLENR[LENGTH]-1 received BDs.
|
| Configure the receive ring consumer index register RBaCIR. The
| consumer index is owned by software and updated during operation of the
| of the BD ring by software, to indicate that any receive data occupied
| in the BD has been processed and it has been prepared for new data.
| - If consumer index and producer index are initialized to the same
| value, it indicates that all BDs in the ring have been prepared and
| hardware owns all of the entries.
| - If consumer index is initialized to producer index plus N, it would
| indicate N BDs have been prepared. Note that hardware cannot start if
| only a single buffer is prepared due to the restrictions described in
| (2).
| - Software may write consumer index to match producer index anytime
| while the ring is operational to indicate all received BDs prior have
| been processed and new BDs prepared for hardware.
Normally, the value of rx_ring->rcir (consumer index) is brought in sync
with the rx_ring->next_to_use software index, but this only happens if
page allocation ever succeeded.
When PI==CI==0, the hardware appears to receive frames and write them to
DMA address 0x0 (?!), then set the READY bit in the BD.
The enetc_clean_rx_ring() function (and its XDP derivative) is naturally
not prepared to handle such a condition. It will attempt to process
those frames using the rx_swbd structure associated with index i of the
RX ring, but that structure is not fully initialized (enetc_new_page()
does all of that). So what happens next is undefined behavior.
To operate using no buffer, we must initialize the CI to PI + 1, which
will block the hardware from advancing the CI any further, and drop
everything.
The issue was seen while adding support for zero-copy AF_XDP sockets,
where buffer memory comes from user space, which can even decide to
supply no buffers at all (example: "xdpsock --txonly"). However, the bug
is present also with the network stack code, even though it would take a
very determined person to trigger a page allocation failure at the
perfect time (a series of ifup/ifdown under memory pressure should
eventually reproduce it given enough retries).
Fixes: d4fd0404c1 ("enetc: Introduce basic PF and VF ENETC ethernet drivers")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Claudiu Manoil <claudiu.manoil@nxp.com>
Link: https://lore.kernel.org/r/20221027182925.3256653-1-vladimir.oltean@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Similar to changes done in TCP in blamed commit.
We should not sense pfmemalloc status in sendpage() methods.
Fixes: 3261400639 ("tcp: TX zerocopy should not sense pfmemalloc status")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Link: https://lore.kernel.org/r/20221027040637.1107703-1-edumazet@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Use the event group trees to iterate only perf_tracepoint events.
Signed-off-by: Ravi Bangoria <ravi.bangoria@amd.com
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
There have been various issues and limitations with the way perf uses
(task) contexts to track events. Most notable is the single hardware
PMU task context, which has resulted in a number of yucky things (both
proposed and merged).
Notably:
- HW breakpoint PMU
- ARM big.little PMU / Intel ADL PMU
- Intel Branch Monitoring PMU
- AMD IBS PMU
- S390 cpum_cf PMU
- PowerPC trace_imc PMU
*Current design:*
Currently we have a per task and per cpu perf_event_contexts:
task_struct::perf_events_ctxp[] <-> perf_event_context <-> perf_cpu_context
^ | ^ | ^
`---------------------------------' | `--> pmu ---'
v ^
perf_event ------'
Each task has an array of pointers to a perf_event_context. Each
perf_event_context has a direct relation to a PMU and a group of
events for that PMU. The task related perf_event_context's have a
pointer back to that task.
Each PMU has a per-cpu pointer to a per-cpu perf_cpu_context, which
includes a perf_event_context, which again has a direct relation to
that PMU, and a group of events for that PMU.
The perf_cpu_context also tracks which task context is currently
associated with that CPU and includes a few other things like the
hrtimer for rotation etc.
Each perf_event is then associated with its PMU and one
perf_event_context.
*Proposed design:*
New design proposed by this patch reduce to a single task context and
a single CPU context but adds some intermediate data-structures:
task_struct::perf_event_ctxp -> perf_event_context <- perf_cpu_context
^ | ^ ^
`---------------------------' | |
| | perf_cpu_pmu_context <--.
| `----. ^ |
| | | |
| v v |
| ,--> perf_event_pmu_context |
| | |
| | |
v v |
perf_event ---> pmu ----------------'
With the new design, perf_event_context will hold all events for all
pmus in the (respective pinned/flexible) rbtrees. This can be achieved
by adding pmu to rbtree key:
{cpu, pmu, cgroup, group_index}
Each perf_event_context carries a list of perf_event_pmu_context which
is used to hold per-pmu-per-context state. For example, it keeps track
of currently active events for that pmu, a pmu specific task_ctx_data,
a flag to tell whether rotation is required or not etc.
Additionally, perf_cpu_pmu_context is used to hold per-pmu-per-cpu
state like hrtimer details to drive the event rotation, a pointer to
perf_event_pmu_context of currently running task and some other
ancillary information.
Each perf_event is associated to it's pmu, perf_event_context and
perf_event_pmu_context.
Further optimizations to current implementation are possible. For
example, ctx_resched() can be optimized to reschedule only single pmu
events.
Much thanks to Ravi for picking this up and pushing it towards
completion.
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Co-developed-by: Ravi Bangoria <ravi.bangoria@amd.com>
Signed-off-by: Ravi Bangoria <ravi.bangoria@amd.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Link: https://lkml.kernel.org/r/20221008062424.313-1-ravi.bangoria@amd.com
The cited commit at rx sa update operation passes the sci object
attribute, in the wrong endianness and not as expected by the HW
effectively create malformed hw sa context in case of update rx sa
consequently, HW produces unexpected MACsec packets which uses this
sa.
Fix by passing sci to create macsec object with the correct endianness,
while at it add __force u64 to prevent sparse check error of type
"sparse: error: incorrect type in assignment".
Fixes: aae3454e4d ("net/mlx5e: Add MACsec offload Rx command support")
Signed-off-by: Raed Salem <raeds@nvidia.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Link: https://lore.kernel.org/r/20221026135153.154807-16-saeed@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The cited commit produces a sparse check error of type
"sparse: error: restricted __be64 degrades to integer". The
offending line wrongly did a bitwise operation between two different
storage types one of 64 bit when the other smaller side is 16 bit
which caused the above sparse error, furthermore bitwise operation
usage here is wrong in the first place as the constant MACSEC_PORT_ES
is not a bitwise field.
Fix by using the right mask to get the lower 16 bit if the sci number,
and use comparison operator '==' instead of bitwise '&' operator.
Fixes: 3b20949cb2 ("net/mlx5e: Add MACsec RX steering rules")
Signed-off-by: Raed Salem <raeds@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Link: https://lore.kernel.org/r/20221026135153.154807-15-saeed@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The cited commit adds the support for update/delete MACsec Rx SA,
naturally, these operations need to check if the SA in question exists
to update/delete the SA and return error code otherwise, however they
do just the opposite i.e. return with error if the SA exists
Fix by change the check to return error in case the SA in question does
not exist, adjust error message and code accordingly.
Fixes: aae3454e4d ("net/mlx5e: Add MACsec offload Rx command support")
Signed-off-by: Raed Salem <raeds@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Link: https://lore.kernel.org/r/20221026135153.154807-14-saeed@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The cited commit at update rx sa operation passes object attributes
to MACsec object create function without initializing/setting all
attributes fields leaving some of them with garbage values, therefore
violating the implicit assumption at create object function, which
assumes that all input object attributes fields are set.
Fix by initializing the object attributes struct to zero, thus leaving
unset fields with the legal zero value.
Fixes: aae3454e4d ("net/mlx5e: Add MACsec offload Rx command support")
Signed-off-by: Raed Salem <raeds@nvidia.com>
Reviewed-by: Lior Nahmanson <liorna@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Link: https://lore.kernel.org/r/20221026135153.154807-13-saeed@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
When setting Bluefield to DPU NIC mode using mlxconfig tool + sync
firmware reset flow, we run into scenario where the host was not
eswitch manager at the time of mlx5 driver load but becomes eswitch manager
after the sync firmware reset flow. This results in null pointer
access of mpfs structure during mac filter add. This change prevents null
pointer access but mpfs table entries will not be added.
Fixes: 5ec697446f ("net/mlx5: Add support for devlink reload action fw activate")
Signed-off-by: Suresh Devarakonda <ramad@nvidia.com>
Reviewed-by: Moshe Shemesh <moshe@nvidia.com>
Reviewed-by: Bodong Wang <bodong@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Link: https://lore.kernel.org/r/20221026135153.154807-12-saeed@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Update devlink health fw fatal reporter state to "healthy" is needed by
strictly calling devlink_health_reporter_state_update() after recovery
was done by PCI error handler. This is needed when fw_fatal reporter was
triggered due to PCI error. Poll health is called and set reporter state
to error. Health recovery failed (since EEH didn't re-enable the PCI).
PCI handlers keep on recover flow and succeed later without devlink
acknowledgment. Fix this by adding devlink state update at the end of
the PCI handler recovery process.
Fixes: 6181e5cb75 ("devlink: add support for reporter recovery completion")
Signed-off-by: Roy Novich <royno@nvidia.com>
Reviewed-by: Moshe Shemesh <moshe@nvidia.com>
Reviewed-by: Aya Levin <ayal@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Link: https://lore.kernel.org/r/20221026135153.154807-11-saeed@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
On multi table split the driver creates a new attr instance with
data being copied from prev attr instance zeroing action flags.
Also need to reset dests properties to avoid incorrect dests per attr.
Fixes: 8300f22526 ("net/mlx5e: Create new flow attr for multi table actions")
Signed-off-by: Roi Dayan <roid@nvidia.com>
Reviewed-by: Maor Dickman <maord@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Link: https://lore.kernel.org/r/20221026135153.154807-10-saeed@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Reject TC rules that forward from internal port to internal port
as it is not supported.
This include rules that are explicitly have internal port as
the filter device as well as rules that apply on tunnel interfaces
as the route device for the tunnel interface can be an internal
port.
Fixes: 27484f7170 ("net/mlx5e: Offload tc rules that redirect to ovs internal port")
Signed-off-by: Ariel Levkovich <lariel@nvidia.com>
Reviewed-by: Maor Dickman <maord@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Link: https://lore.kernel.org/r/20221026135153.154807-9-saeed@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
mlx5 SQs must select the timestamp format explicitly according to the
active clock mode, select the current active timestamp mode so ASO SQ create
will succeed.
This fixes the following error prints when trying to create ipsec ASO SQ
while the timestamp format is real time mode.
mlx5_cmd_out_err:778:(pid 34874): CREATE_SQ(0x904) op_mod(0x0) failed, status bad parameter(0x3), syndrome (0xd61c0b), err(-22)
mlx5_aso_create_sq:285:(pid 34874): Failed to open aso wq sq, err=-22
mlx5e_ipsec_init:436:(pid 34874): IPSec initialization failed, -22
Fixes: cdd04f4d4d ("net/mlx5: Add support to create SQ and CQ for ASO")
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Reported-by: Leon Romanovsky <leonro@nvidia.com>
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Link: https://lore.kernel.org/r/20221026135153.154807-7-saeed@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Currently encap slow path rules just forward to software without
setting the chain id miss register, so driver doesn't restore
the chain, and packets hitting this rule will restart from tc chain
0 instead of continuing to the chain the encap rule was on.
Fix this by setting the chain id miss register to the chain id mapping.
Fixes: 8f1e0b97cc ("net/mlx5: E-Switch, Mark miss packets with new chain id mapping")
Signed-off-by: Paul Blakey <paulb@nvidia.com>
Reviewed-by: Oz Shlomo <ozsh@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Link: https://lore.kernel.org/r/20221026135153.154807-6-saeed@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
When tx_port_ts is set, the driver diverts all UPD traffic over PTP port
to a dedicated PTP-SQ. The SKBs are cached until the wire-CQE arrives.
When the packet size is greater then MTU, the firmware might drop it and
the packet won't be transmitted to the wire, hence the wire-CQE won't
reach the driver. In this case the SKBs are accumulated in the SKB fifo.
Add room check to consider the PTP-SQ SKB fifo, when the SKB fifo is
full, driver stops the queue resulting in a TX timeout. Devlink
TX-reporter can recover from it.
Fixes: 1880bc4e4a ("net/mlx5e: Add TX port timestamp support")
Signed-off-by: Aya Levin <ayal@nvidia.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Link: https://lore.kernel.org/r/20221026135153.154807-5-saeed@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
When 2nd flow rules arrives, it will merge together with the
1st one if matcher criteria is the same.
If merge fails, driver will rollback the merge contents, and
reject the 2nd rule. At rollback stage, matcher can't be
disconnected unconditionally, otherise the 1st rule can't be
hit anymore.
Add logic to check if the matcher should be disconnected or not.
Fixes: cc2295cd54 ("net/mlx5: DR, Improve steering for empty or RX/TX-only matchers")
Signed-off-by: Rongwei Liu <rongweil@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Link: https://lore.kernel.org/r/20221026135153.154807-4-saeed@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
After firmware reset driver should verify firmware already enabled CRS
and became responsive to pci config cycles before restoring pci state.
Fix that by waiting till device_id is readable through PCI again.
Fixes: eabe8e5e88 ("net/mlx5: Handle sync reset now event")
Signed-off-by: Moshe Shemesh <moshe@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Link: https://lore.kernel.org/r/20221026135153.154807-3-saeed@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
An offloaded SA stops receiving after about 2^32 + replay_window
packets. For example, when SA reaches <seq-hi 0x1, seq 0x2c>, all
subsequent packets get dropped with SA-icv-failure (integrity_failed).
To reproduce the bug:
- ConnectX-6 Dx with crypto enabled (FW 22.30.1004)
- ipsec.conf:
nic-offload = yes
replay-window = 32
esn = yes
salifetime=24h
- Run netperf for a long time to send more than 2^32 packets
netperf -H <device-under-test> -t TCP_STREAM -l 20000
When 2^32 + replay_window packets are received, the replay window
moves from the 2nd half of subspace (overlap=1) to the 1st half
(overlap=0). The driver then updates the 'esn' value in NIC
(i.e. seq_hi) as follows.
seq_hi = xfrm_replay_seqhi(seq_bottom)
new esn in NIC = seq_hi + 1
The +1 increment is wrong, as seq_hi already contains the correct
seq_hi. For example, when seq_hi=1, the driver actually tells NIC to
use seq_hi=2 (esn). This incorrect esn value causes all subsequent
packets to fail integrity checks (SA-icv-failure). So, do not
increment.
Fixes: cb01008390 ("net/mlx5: IPSec, Add support for ESN")
Signed-off-by: Hyong Youb Kim <hyonkim@cisco.com>
Acked-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Link: https://lore.kernel.org/r/20221026135153.154807-2-saeed@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Zhengchao Shao says:
====================
fix some issues in netdevsim driver
When strace tool is used to perform memory injection, memory leaks and
files not removed issues are found. Fix them.
====================
Link: https://lore.kernel.org/r/20221026014642.116261-1-shaozhengchao@huawei.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Remove dir in nsim_dev_debugfs_init() when creating ports dir failed.
Otherwise, the netdevsim device will not be created next time. Kernel
reports an error: debugfs: Directory 'netdevsim1' with parent 'netdevsim'
already present!
Fixes: ab1d0cc004 ("netdevsim: change debugfs tree topology")
Signed-off-by: Zhengchao Shao <shaozhengchao@huawei.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
-----BEGIN PGP SIGNATURE-----
iQFHBAABCgAxFiEEBsvAIBsPu6mG7thcrX5LkNig010FAmNabUQTHG1rbEBwZW5n
dXRyb25peC5kZQAKCRCtfkuQ2KDTXaTBB/9xLKgfBKQtTKpLJ8HoDLESWbHr6v9T
8GmOY0+UPbKxOqfMknYfwV57ca9agIw5IOFx9ry7w6PrytDF2S5ojYHtmQvvbmQJ
2HyuP8k4Qt3MIS2O1fxHg6fe4qMhdDBJ2vkp5AGsfFWG3i189gPAGQFOtI19Zt+j
Se547s5WzGlgcCQulbveyJsTO85Z6xhBr7VOy8mxSkkxivrYzKRk7YjWlulHCCFF
A/Q15dXFyBtH+oG+Gl3Nnj0ttgiE7X6oOzwTH5JkUmUDnTujPZQX+tcJYNHKB+xw
m3fwqRM8mWb1+m1gCgDKVT0Yaurbhbmv1phdZcPgFjCVU6PR1miFFG8M
=YUyU
-----END PGP SIGNATURE-----
Merge tag 'linux-can-fixes-for-6.1-20221027' of git://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can
Marc Kleine-Budde says:
====================
pull-request: can 2022-10-27
Anssi Hannula fixes the use of the completions in the kvaser_usb
driver.
Biju Das contributes 2 patches for the rcar_canfd driver. A IRQ storm
that can be triggered by high CAN bus load and channel specific IRQ
handlers are fixed.
Yang Yingliang fixes the j1939 transport protocol by moving a
kfree_skb() out of a spin_lock_irqsave protected section.
* tag 'linux-can-fixes-for-6.1-20221027' of git://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can:
can: j1939: transport: j1939_session_skb_drop_old(): spin_unlock_irqrestore() before kfree_skb()
can: rcar_canfd: fix channel specific IRQ handling for RZ/G2L
can: rcar_canfd: rcar_canfd_handle_global_receive(): fix IRQ storm on global FIFO receive
can: kvaser_usb: Fix possible completions during init_completion
====================
Link: https://lore.kernel.org/r/20221027114356.1939821-1-mkl@pengutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Queueing packets doesn't guarantee their transmission. Update TX stats
after hardware confirms consuming submitted data.
This also fixes a possible race and NULL dereference.
bcm4908_enet_start_xmit() could try to access skb after freeing it in
the bcm4908_enet_poll_tx().
Reported-by: Florian Fainelli <f.fainelli@gmail.com>
Fixes: 4feffeadbc ("net: broadcom: bcm4908enet: add BCM4908 controller driver")
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/20221027112430.8696-1-zajec5@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Pull the SDVO audio state computation into a helper.
This is almost identical to intel_hdmi_has_audio(),
except the sink capabilities are stored under intel_sdvo
rather than intel_hdmi. Might be nice to get rid of
this duplication eventually...
Cc: Chaitanya Kumar Borah <chaitanya.kumar.borah@intel.com>
Cc: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Cc: Takashi Iwai <tiwai@suse.de>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20221026170150.2654-16-ville.syrjala@linux.intel.com
The spec tells us to do a bunch of vblank waits in the audio
enable/disable sequences. Make it so.
The FIXMEs are nonsense since we do the audio disable very
early and enable very late, so vblank interrupts are in fact
enabled when we do this.
TODO not sure we actually want these since we don't even rely
on the hw ELD buffer, and these might be there just to give
the audio side a bit of time to respond to the unsol events.
OTOH they might be really needed for some other reason.
Cc: Chaitanya Kumar Borah <chaitanya.kumar.borah@intel.com>
Cc: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Cc: Takashi Iwai <tiwai@suse.de>
Acked-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20221026170150.2654-15-ville.syrjala@linux.intel.com
On the older platforms the audio presence detect bit is in
the port register, so it gets written outside audio codec hooks
and is this separate from the ELD valid toggling. Split the
operations into two steps on hsw+ to be more consistent with
both the other platforms and the spec. Also according to the
spec we might need some vblank waits between the two which
definitely needs them done separately.
Cc: Chaitanya Kumar Borah <chaitanya.kumar.borah@intel.com>
Cc: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Cc: Takashi Iwai <tiwai@suse.de>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20221026170150.2654-14-ville.syrjala@linux.intel.com
The audio code does a lot of RMW accesses. Utilize
intel_de_rmw() to make that a bit less tedious.
There are still some hand rolled RMW left, but those have
a lot of code in between the read and write to calculate
the new value, so would need some refactoring first.
v2: Add parens around the ?: to satisfy the robot
Cc: Chaitanya Kumar Borah <chaitanya.kumar.borah@intel.com>
Cc: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Cc: Takashi Iwai <tiwai@suse.de>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20221026170150.2654-13-ville.syrjala@linux.intel.com
Make the eld pointer u32* so we don't have to do super
ugly casting in the code itself.
Cc: Chaitanya Kumar Borah <chaitanya.kumar.borah@intel.com>
Cc: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Cc: Takashi Iwai <tiwai@suse.de>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20221026170150.2654-12-ville.syrjala@linux.intel.com
Currently we only write as many dwords into the hardware
ELD buffers as drm_eld_size() tells us. That could mean the
remainder of the hardware buffer is left with whatever
stale garbage it had before, which doesn't seem entirely
great. Let's zero out the remainder of the buffer in case
the provided ELD doesn't fill it fully.
We can also sanity check out idea of the hardware ELD buffer's
size by making sure the address wrapped back to zero once
we wrote the entire buffer.
Cc: Chaitanya Kumar Borah <chaitanya.kumar.borah@intel.com>
Cc: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Cc: Takashi Iwai <tiwai@suse.de>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20221026170150.2654-11-ville.syrjala@linux.intel.com
We currently read the ELD buffer size from hardware on g4x,
but on ilk+ we just hardcode it to 84 bytes. Let's unify
this and just do the hardware readout on all platforms,
in case the size changes in the future or something.
TODO: should perhaps do the readout during driver init and
stash the results somewhere so that we could check that the
connector's ELD actually fits and not even try to enable audio
in that case...
v2: Document the size is in dwords (Jani)
Cc: Chaitanya Kumar Borah <chaitanya.kumar.borah@intel.com>
Cc: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Cc: Takashi Iwai <tiwai@suse.de>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20221026170150.2654-10-ville.syrjala@linux.intel.com
No idea why we do this ELD comparions on g4x before loading
the new ELD. Seems entirely pointless so just get rid of it.
Cc: Chaitanya Kumar Borah <chaitanya.kumar.borah@intel.com>
Cc: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Cc: Takashi Iwai <tiwai@suse.de>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20221026170150.2654-9-ville.syrjala@linux.intel.com
On the "ilk" platforms AUD_CNTL_ST2 is a singleton. Protect
it with the audio mutex in case we ever want to do parallel
RMW access to it.
Currently that should not happen since we only do audio
enable/disable from full modesets, and those are fully
serialized. But we probably want to think about toggling
audio on/off from fastsets too.
The hsw codepaths already have the same locking.
g4x should not need it since it can only do audio to a
single port at a time, which means it's actually broken
in more ways than this atm.
Cc: Chaitanya Kumar Borah <chaitanya.kumar.borah@intel.com>
Cc: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Cc: Takashi Iwai <tiwai@suse.de>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20221026170150.2654-8-ville.syrjala@linux.intel.com
Rename a few g4x bits to match the ibx+ bits.
Cc: Chaitanya Kumar Borah <chaitanya.kumar.borah@intel.com>
Cc: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Cc: Takashi Iwai <tiwai@suse.de>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20221026170150.2654-7-ville.syrjala@linux.intel.com
The "ilk" audio codec codepaths have some duplicated code
to figure out the correct registers to use on each platform.
Extrat that into a single place.
Cc: Chaitanya Kumar Borah <chaitanya.kumar.borah@intel.com>
Cc: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Cc: Takashi Iwai <tiwai@suse.de>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20221026170150.2654-5-ville.syrjala@linux.intel.com
We don't use the audio code on crestline (CL) since it doesn't
support native HDMI output, and SDVO has it's own way of doing
audio.
And Bearlake-C (BLC) doesn't even exist in the real world, so
no point it trying to deal with it.
Cc: Chaitanya Kumar Borah <chaitanya.kumar.borah@intel.com>
Cc: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Cc: Takashi Iwai <tiwai@suse.de>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20221026170150.2654-4-ville.syrjala@linux.intel.com
Remove some leftovers I missed in commit
2dd43144e8 ("drm/i915: Streamline the artihmetic")
Cc: Chaitanya Kumar Borah <chaitanya.kumar.borah@intel.com>
Cc: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Cc: Takashi Iwai <tiwai@suse.de>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20221026170150.2654-3-ville.syrjala@linux.intel.com
Rename the 'dev_priv' variables to 'i915' in the audio code
to match modern style conventions.
v2: Drop some needless braces in intel_audio_hooks_init()
Cc: Chaitanya Kumar Borah <chaitanya.kumar.borah@intel.com>
Cc: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Cc: Takashi Iwai <tiwai@suse.de>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20221026170150.2654-2-ville.syrjala@linux.intel.com
Nicolas Dichtel says:
====================
ip: rework the fix for dflt addr selection for connected nexthop"
This series reworks the fix that is reverted in the second commit.
As Julian explained, nhc_scope is related to nhc_gw, it's not the scope of
the route.
====================
Link: https://lore.kernel.org/r/20221020100952.8748-1-nicolas.dichtel@6wind.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
As explained by Julian, fib_nh_scope is related to fib_nh_gw4, but
fib_info_update_nhc_saddr() needs the scope of the route, which is
the scope "before" fib_nh_scope, ie fib_nh_scope - 1.
This patch fixes the problem described in commit 747c143072 ("ip: fix
dflt addr selection for connected nexthop").
Fixes: 597cfe4fc3 ("nexthop: Add support for IPv4 nexthops")
Link: https://lore.kernel.org/netdev/6c8a44ba-c2d5-cdf-c5c7-5baf97cba38@ssi.bg/
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Reviewed-by: Julian Anastasov <ja@ssi.bg>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This reverts commit 747c143072.
As explained by Julian, nhc_scope is related to nhc_gw, not to the route.
Revert the original patch. The initial problem is fixed differently in the
next commit.
Link: https://lore.kernel.org/netdev/6c8a44ba-c2d5-cdf-c5c7-5baf97cba38@ssi.bg/
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Reviewed-by: Julian Anastasov <ja@ssi.bg>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This reverts commit eb55dc09b5.
The patch that introduces this bug is reverted right after this one.
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Reviewed-by: Julian Anastasov <ja@ssi.bg>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
