[ Upstream commit 71e99ee20f ]
nf_tables_addchain() publishes the chain to table->chains via
list_add_tail_rcu() (in nft_chain_add()) before registering hooks.
If nf_tables_register_hook() then fails, the error path calls
nft_chain_del() (list_del_rcu()) followed by nf_tables_chain_destroy()
with no RCU grace period in between.
This creates two use-after-free conditions:
1) Control-plane: nf_tables_dump_chains() traverses table->chains
under rcu_read_lock(). A concurrent dump can still be walking
the chain when the error path frees it.
2) Packet path: for NFPROTO_INET, nf_register_net_hook() briefly
installs the IPv4 hook before IPv6 registration fails. Packets
entering nft_do_chain() via the transient IPv4 hook can still be
dereferencing chain->blob_gen_X when the error path frees the
chain.
Add synchronize_rcu() between nft_chain_del() and the chain destroy
so that all RCU readers -- both dump threads and in-flight packet
evaluation -- have finished before the chain is freed.
Fixes: 91c7b38dc9 ("netfilter: nf_tables: use new transaction infrastructure to handle chain")
Signed-off-by: Inseo An <y0un9sa@gmail.com>
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 008e7a7c29 ]
Although unlikely, recent support for IPIP tunnels increases chances of
reaching this WARN_ON_ONCE if userspace manages to build a sufficiently
long forward path.
Remove it.
Fixes: ddb94eafab ("net: resolve forwarding path from virtual netdevice and HW destination address")
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8fde939b02 ]
There is race between the netdev notifier ip_vs_dst_event()
and the code that caches dst with dev that is going down.
As the FIB can be notified for the closed device after our
handler finishes, it is possible valid route to be returned
and cached resuling in a leaked dev reference until the dest
is not removed.
To prevent new dest_dst to be attached to dest just after the
handler dropped the old one, add a netif_running() check
to make sure the notifier handler is not currently running
for device that is closing.
Fixes: 7a4f0761fc ("IPVS: init and cleanup restructuring")
Signed-off-by: Julian Anastasov <ja@ssi.bg>
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ce9f6aec0f ]
The test generates VXLAN traffic using mausezahn, where the encapsulated
inner IPv6 packet has an incorrect payload length set in the IPv6 header.
After VXLAN decapsulation, such packets do not pass sanity checks in
br_netfilter and are dropped, which causes the test to fail.
Fix this by setting the correct IPv6 payload length for the encapsulated
packet generated by mausezahn, so that the packet is accepted
by br_netfilter.
tools/testing/selftests/net/forwarding/vxlan_bridge_1d_ipv6.sh
lines 698-706
)"00:03:"$( : Payload length
)"3a:"$( : Next header
)"04:"$( : Hop limit
)"$saddr:"$( : IP saddr
)"$daddr:"$( : IP daddr
)"80:"$( : ICMPv6.type
)"00:"$( : ICMPv6.code
)"00:"$( : ICMPv6.checksum
)
Data after IPv6 header:
• 80: — 1 byte (ICMPv6 type)
• 00: — 1 byte (ICMPv6 code)
• 00: — 1 byte (ICMPv6 checksum, truncated)
Total: 3 bytes → 00:03 is correct. The old value 00:08 did not match
the actual payload size.
Fixes: b07e9957f2 ("selftests: forwarding: Add VxLAN tests with a VLAN-unaware bridge for IPv6")
Signed-off-by: Aleksei Oladko <aleksey.oladko@virtuozzo.com>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Link: https://patch.msgid.link/20260213131907.43351-3-aleksey.oladko@virtuozzo.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 02cb2e6bac ]
The test generates VXLAN traffic using mausezahn, where the encapsulated
inner IPv4 packet contains a zero IP header checksum. After VXLAN
decapsulation, such packets do not pass sanity checks in br_netfilter
and are dropped, which causes the test to fail.
Fix this by calculating and setting a valid IPv4 header checksum for the
encapsulated packet generated by mausezahn, so that the packet is accepted
by br_netfilter. Fixed by using the payload_template_calc_checksum() /
payload_template_expand_checksum() helpers that are only available
in v6.3 and newer kernels.
Fixes: a0b61f3d8e ("selftests: forwarding: vxlan_bridge_1d: Add an ECN decap test")
Signed-off-by: Aleksei Oladko <aleksey.oladko@virtuozzo.com>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Link: https://patch.msgid.link/20260213131907.43351-2-aleksey.oladko@virtuozzo.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8b769e311a ]
syzbot triggered a warning[1] about the number of mdb entries in a context.
It turned out that there are multiple ways to trigger that warning today
(some got added during the years), the root cause of the problem is that
the increase is done conditionally, and over the years these different
conditions increased so there were new ways to trigger the warning, that is
to do a decrease which wasn't paired with a previous increase.
For example one way to trigger it is with flush:
$ ip l add br0 up type bridge vlan_filtering 1 mcast_snooping 1
$ ip l add dumdum up master br0 type dummy
$ bridge mdb add dev br0 port dumdum grp 239.0.0.1 permanent vid 1
$ ip link set dev br0 down
$ ip link set dev br0 type bridge mcast_vlan_snooping 1
^^^^ this will enable snooping, but will not update mdb_n_entries
because in __br_multicast_enable_port_ctx() we check !netif_running
$ bridge mdb flush dev br0
^^^ this will trigger the warning because it will delete the pg which
we added above, which will try to decrease mdb_n_entries
Fix the problem by removing the conditional increase and always keep the
count up-to-date while the vlan exists. In order to do that we have to
first initialize it on port-vlan context creation, and then always increase
or decrease the value regardless of mcast options. To keep the current
behaviour we have to enforce the mdb limit only if the context is port's or
if the port-vlan's mcast snooping is enabled.
[1]
------------[ cut here ]------------
n == 0
WARNING: net/bridge/br_multicast.c:718 at br_multicast_port_ngroups_dec_one net/bridge/br_multicast.c:718 [inline], CPU#0: syz.4.4607/22043
WARNING: net/bridge/br_multicast.c:718 at br_multicast_port_ngroups_dec net/bridge/br_multicast.c:771 [inline], CPU#0: syz.4.4607/22043
WARNING: net/bridge/br_multicast.c:718 at br_multicast_del_pg+0x1bbe/0x1e20 net/bridge/br_multicast.c:825, CPU#0: syz.4.4607/22043
Modules linked in:
CPU: 0 UID: 0 PID: 22043 Comm: syz.4.4607 Not tainted syzkaller #0 PREEMPT(full)
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/24/2026
RIP: 0010:br_multicast_port_ngroups_dec_one net/bridge/br_multicast.c:718 [inline]
RIP: 0010:br_multicast_port_ngroups_dec net/bridge/br_multicast.c:771 [inline]
RIP: 0010:br_multicast_del_pg+0x1bbe/0x1e20 net/bridge/br_multicast.c:825
Code: 41 5f 5d e9 04 7a 48 f7 e8 3f 73 5c f7 90 0f 0b 90 e9 cf fd ff ff e8 31 73 5c f7 90 0f 0b 90 e9 16 fd ff ff e8 23 73 5c f7 90 <0f> 0b 90 e9 60 fd ff ff e8 15 73 5c f7 eb 05 e8 0e 73 5c f7 48 8b
RSP: 0018:ffffc9000c207220 EFLAGS: 00010293
RAX: ffffffff8a68042d RBX: ffff88807c6f1800 RCX: ffff888066e90000
RDX: 0000000000000000 RSI: 0000000000000000 RDI: 0000000000000000
RBP: 0000000000000000 R08: ffff888066e90000 R09: 000000000000000c
R10: 000000000000000c R11: 0000000000000000 R12: ffff8880303ef800
R13: dffffc0000000000 R14: ffff888050eb11c4 R15: 1ffff1100a1d6238
FS: 00007fa45921b6c0(0000) GS:ffff8881256f5000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 00007fa4591f9ff8 CR3: 0000000081df2000 CR4: 00000000003526f0
Call Trace:
<TASK>
br_mdb_flush_pgs net/bridge/br_mdb.c:1525 [inline]
br_mdb_flush net/bridge/br_mdb.c:1544 [inline]
br_mdb_del_bulk+0x5e2/0xb20 net/bridge/br_mdb.c:1561
rtnl_mdb_del+0x48a/0x640 net/core/rtnetlink.c:-1
rtnetlink_rcv_msg+0x77e/0xbe0 net/core/rtnetlink.c:6967
netlink_rcv_skb+0x232/0x4b0 net/netlink/af_netlink.c:2550
netlink_unicast_kernel net/netlink/af_netlink.c:1318 [inline]
netlink_unicast+0x80f/0x9b0 net/netlink/af_netlink.c:1344
netlink_sendmsg+0x813/0xb40 net/netlink/af_netlink.c:1894
sock_sendmsg_nosec net/socket.c:727 [inline]
__sock_sendmsg net/socket.c:742 [inline]
____sys_sendmsg+0xa68/0xad0 net/socket.c:2592
___sys_sendmsg+0x2a5/0x360 net/socket.c:2646
__sys_sendmsg net/socket.c:2678 [inline]
__do_sys_sendmsg net/socket.c:2683 [inline]
__se_sys_sendmsg net/socket.c:2681 [inline]
__x64_sys_sendmsg+0x1bd/0x2a0 net/socket.c:2681
do_syscall_x64 arch/x86/entry/syscall_64.c:63 [inline]
do_syscall_64+0xe2/0xf80 arch/x86/entry/syscall_64.c:94
entry_SYSCALL_64_after_hwframe+0x77/0x7f
RIP: 0033:0x7fa45839aeb9
Code: ff c3 66 2e 0f 1f 84 00 00 00 00 00 0f 1f 44 00 00 48 89 f8 48 89 f7 48 89 d6 48 89 ca 4d 89 c2 4d 89 c8 4c 8b 4c 24 08 0f 05 <48> 3d 01 f0 ff ff 73 01 c3 48 c7 c1 e8 ff ff ff f7 d8 64 89 01 48
RSP: 002b:00007fa45921b028 EFLAGS: 00000246 ORIG_RAX: 000000000000002e
RAX: ffffffffffffffda RBX: 00007fa458615fa0 RCX: 00007fa45839aeb9
RDX: 0000000000000000 RSI: 00002000000000c0 RDI: 0000000000000004
RBP: 00007fa458408c1f R08: 0000000000000000 R09: 0000000000000000
R10: 0000000000000000 R11: 0000000000000246 R12: 0000000000000000
R13: 00007fa458616038 R14: 00007fa458615fa0 R15: 00007fff0b59fae8
</TASK>
Fixes: b57e8d870d ("net: bridge: Maintain number of MDB entries in net_bridge_mcast_port")
Reported-by: syzbot+d5d1b7343531d17bd3c5@syzkaller.appspotmail.com
Closes: https://lore.kernel.org/netdev/aYrWbRp83MQR1ife@debil/T/#t
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Link: https://patch.msgid.link/20260213070031.1400003-2-nikolay@nvidia.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit da29e453dc ]
Commit 3db6e0d172 ("rds: use RCU to synchronize work-enqueue with
connection teardown") modifies rds_sendmsg to avoid enqueueing work
while a tear down is in progress. However, it also changed the return
value of rds_sendmsg to that of rds_send_xmit instead of the
payload_len. This means the user may incorrectly receive errno values
when it should have simply received a payload of 0 while the peer
attempts a reconnections. So this patch corrects the teardown handling
code to only use the out error path in that case, thus restoring the
original payload_len return value.
Fixes: 3db6e0d172 ("rds: use RCU to synchronize work-enqueue with connection teardown")
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: Allison Henderson <achender@kernel.org>
Link: https://patch.msgid.link/20260213035409.1963391-1-achender@kernel.org
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6d1dc80143 ]
A malicious or buggy Xen guest can write "0" to the xenbus key
"multi-queue-num-queues". The connect() function in the backend only
validates the upper bound (requested_num_queues > xenvif_max_queues)
but not zero, allowing requested_num_queues=0 to reach
vzalloc(array_size(0, sizeof(struct xenvif_queue))), which triggers
WARN_ON_ONCE(!size) in __vmalloc_node_range().
On systems with panic_on_warn=1, this allows a guest-to-host denial
of service.
The Xen network interface specification requires
the queue count to be "greater than zero".
Add a zero check to match the validation already present
in xen-blkback, which has included this
guard since its multi-queue support was added.
Fixes: 8d3d53b3e4 ("xen-netback: Add support for multiple queues")
Signed-off-by: Ziyi Guo <n7l8m4@u.northwestern.edu>
Reviewed-by: Juergen Gross <jgross@suse.com>
Link: https://patch.msgid.link/20260212224040.86674-1-n7l8m4@u.northwestern.edu
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9e7021d2ae ]
catc_probe() fills three URBs with hardcoded endpoint pipes without
verifying the endpoint descriptors:
- usb_sndbulkpipe(usbdev, 1) and usb_rcvbulkpipe(usbdev, 1) for TX/RX
- usb_rcvintpipe(usbdev, 2) for interrupt status
A malformed USB device can present these endpoints with transfer types
that differ from what the driver assumes.
Add a catc_usb_ep enum for endpoint numbers, replacing magic constants
throughout. Add usb_check_bulk_endpoints() and usb_check_int_endpoints()
calls after usb_set_interface() to verify endpoint types before use,
rejecting devices with mismatched descriptors at probe time.
Similar to
- commit 90b7f29617 ("net: usb: rtl8150: enable basic endpoint checking")
which fixed the issue in rtl8150.
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Suggested-by: Simon Horman <horms@kernel.org>
Signed-off-by: Ziyi Guo <n7l8m4@u.northwestern.edu>
Link: https://patch.msgid.link/20260212214154.3609844-1-n7l8m4@u.northwestern.edu
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 94560267d6 ]
When deleting a peer in case of keepalive expiration, the peer is
removed from the OpenVPN hashtable and is temporary inserted in a
"release list" for further processing.
This happens in:
ovpn_peer_keepalive_work()
unlock_ovpn(release_list)
This processing includes detaching from the socket being used to
talk to this peer, by restoring its original proto and socket
ops/callbacks.
In case of TCP it may happen that, while the peer is sitting in
the release list, userspace decides to close the socket.
This will result in a concurrent execution of:
tcp_close(sk)
__tcp_close(sk)
sock_orphan(sk)
sk_set_socket(sk, NULL)
The last function call will set sk->sk_socket to NULL.
When the releasing routine is resumed, ovpn_tcp_socket_detach()
will attempt to dereference sk->sk_socket to restore its original
ops member. This operation will crash due to sk->sk_socket being NULL.
Fix this race condition by testing-and-accessing
sk->sk_socket atomically under sk->sk_callback_lock.
Link: https://lore.kernel.org/netdev/176996279620.3109699.15382994681575380467@eldamar.lan/
Link: https://github.com/OpenVPN/ovpn-net-next/issues/29
Signed-off-by: Antonio Quartulli <antonio@openvpn.net>
Fixes: 11851cbd60 ("ovpn: implement TCP transport")
Link: https://patch.msgid.link/20260212213130.11497-1-antonio@openvpn.net
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0f30a31b55 ]
fbnic always advertises ETHTOOL_TCP_DATA_SPLIT_ENABLED via ethtool
.get_ringparam. To enable proper splitting for all flow types, even for
IP/Ethernet flows, this patch sets DMA_HINT_L4 unconditionally for all
RSS and NFC flow steering rules. According to the spec, L4 falls back to
L3 if no valid L4 is found, and L3 falls back to L2 if no L3 is found.
This makes sure that the correct header boundary is used regardless of
traffic type. This is important for zero-copy use cases where we must
ensure that all ZC packets are split correctly.
Fixes: 2b30fc01a6 ("eth: fbnic: Add support for HDS configuration")
Signed-off-by: Bobby Eshleman <bobbyeshleman@meta.com>
Link: https://patch.msgid.link/20260211-fbnic-tcp-hds-fixes-v1-3-55d050e6f606@meta.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit bd254115f3 ]
Increase FBNIC_HDR_BYTES_MIN from 128 to 256 bytes. The previous minimum
was too small to guarantee that very long L2+L3+L4 headers always fit
within the header buffer. When EN_HDR_SPLIT is disabled and a packet
exceeds MAX_HEADER_BYTES, splitting occurs at that byte offset instead
of the header boundary, resulting in some of the header landing in the
payload page. The increased minimum ensures headers always fit with the
MAX_HEADER_BYTES cut off and land in the header page.
Fixes: 2b30fc01a6 ("eth: fbnic: Add support for HDS configuration")
Signed-off-by: Bobby Eshleman <bobbyeshleman@meta.com>
Acked-by: Mohsin Bashir <mohsin.bashr@gmail.com>
Link: https://patch.msgid.link/20260211-fbnic-tcp-hds-fixes-v1-2-55d050e6f606@meta.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit bbeb3bfbff ]
Fix EN_HDR_SPLIT configuration by writing the field to RDE_CTL0 instead
of RDE_CTL1.
Because drop mode configuration and header splitting enablement both use
RDE_CTL0, we consolidate these configurations into the single function
fbnic_config_drop_mode.
Fixes: 2b30fc01a6 ("eth: fbnic: Add support for HDS configuration")
Signed-off-by: Bobby Eshleman <bobbyeshleman@meta.com>
Acked-by: Mohsin Bashir <mohsin.bashr@gmail.com>
Link: https://patch.msgid.link/20260211-fbnic-tcp-hds-fixes-v1-1-55d050e6f606@meta.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0135333914 ]
fbnic supports pause frames. When pause frames are enabled presumably
user expects lossless operation from the NIC. Make sure we configure
RDE (Rx DMA Engine) to DROP_NEVER mode to avoid discards due to delays
in fetching Rx descriptors from the host.
While at it enable DROP_NEVER when NIC only has a single queue
configured. In this case the NIC acts as a FIFO so there's no risk
of head-of-line blocking other queues by making RDE wait. If pause
is disabled this just moves the packet loss from the DMA engine to
the Rx buffer.
Remove redundant call to fbnic_config_drop_mode_rcq(), introduced by
commit 0cb4c0a137 ("eth: fbnic: Implement Rx queue
alloc/start/stop/free"). This call does not add value as
fbnic_enable_rcq(), which is called immediately afterward, already
handles this.
Although we do not support autoneg at this time, preserve tx_pause in
.mac_link_up instead of fbnic_phylink_get_pauseparam()
Signed-off-by: Mohsin Bashir <mohsin.bashr@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/20251113232610.1151712-1-mohsin.bashr@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Stable-dep-of: bbeb3bfbff ("eth: fbnic: set FBNIC_QUEUE_RDE_CTL0_EN_HDR_SPLIT on RDE_CTL0")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b0b1a8583d ]
The add_fd_from_fd_array() function takes a file descriptor as a
parameter and tries to add either map or btf to the corresponding
list of used objects. As was reported by Dan Carpenter, since the
commit c81e4322acf0 ("bpf: Fix a potential use-after-free of BTF
object"), the fdget() is called twice on the file descriptor, and
thus userspace, potentially, can replace the file pointed to by the
file descriptor in between the two calls. On practice, this shouldn't
break anything on the kernel side, but for consistency fix the code
such that only one fdget() is executed.
Reported-by: Dan Carpenter <dan.carpenter@linaro.org>
Closes: https://lore.kernel.org/r/aY689z7gHNv8rgVO@stanley.mountain/
Fixes: ccd2d799ed ("bpf: Fix a potential use-after-free of BTF object")
Signed-off-by: Anton Protopopov <a.s.protopopov@gmail.com>
Link: https://lore.kernel.org/r/20260213212949.759321-1-a.s.protopopov@gmail.com
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 04999b99e8 ]
Fix bpf_linker__add_buf()'s logic of copying data from memory buffer into
memfd. In the event of short write not writing entire buf_sz bytes into memfd
file, we'll append bytes from the beginning of buf *again* (corrupting ELF
file contents) instead of correctly appending the rest of not-yet-read buf
contents.
Closes: https://github.com/libbpf/libbpf/issues/945
Fixes: 6d5e5e5d7c ("libbpf: Extend linker API to support in-memory ELF files")
Signed-off-by: Amery Hung <ameryhung@gmail.com>
Signed-off-by: Andrii Nakryiko <andrii@kernel.org>
Acked-by: Jiri Olsa <jolsa@kernel.org>
Link: https://lore.kernel.org/bpf/20260209230134.3530521-1-ameryhung@gmail.com
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ee5492fd88 ]
Fixes a theoretical race on fw_log between the teardown path and fw_log
write functions.
fw_log is written inside fbnic_fw_log_write() and can be reached from
the mailbox handler fbnic_fw_msix_intr(), but fw_log is freed before
IRQ/MBX teardown during cleanup, resulting in a potential data race of
dereferencing a freed/null variable.
Possible Interleaving Scenario:
CPU0: fbnic_fw_msix_intr() // Entry
fbnic_fw_log_write()
if (fbnic_fw_log_ready()) // true
... preempt ...
CPU1: fbnic_remove() // Entry
fbnic_fw_log_free()
vfree(log->data_start);
log->data_start = NULL;
CPU0: continues, walks log->entries or writes to log->data_start
The initialization also has an incorrect order problem, as the fw_log
is currently allocated after MBX setup during initialization.
Fix the problems by adjusting the synchronization order to put
initialization in place before the mailbox is enabled, and not cleared
until after the mailbox has been disabled.
Fixes: ecc53b1b46 ("eth: fbnic: Enable firmware logging")
Signed-off-by: Chengfeng Ye <dg573847474@gmail.com>
Link: https://patch.msgid.link/20260211191329.530886-1-dg573847474@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a49d2a2c37 ]
The max_adj field in ptp_clock_info tells userspace how much the PHC
clock frequency can be adjusted. ptp4l reads this and will never request
a correction larger than max_adj.
On both sparx5 and lan969x the clock offset may never converge because
the servo needs a frequency correction larger than the current max_adj
of 200000 (200 ppm) allows. The servo rails at the max and the offset
stays in the tens of microseconds.
The hardware has no inherent max adjustment limit; frequency correction
is done by writing a 64-bit clock period increment to CLK_PER_CFG, and
the register has plenty of range. The 200000 value was just an overly
conservative software limit. The max_adj is shared between sparx5 and
lan969x, and the increased value is safe for both.
Fix this by increasing max_adj to 10000000 (10000 ppm), giving the
servo sufficient headroom.
Fixes: 0933bd0404 ("net: sparx5: Add support for ptp clocks")
Signed-off-by: Daniel Machon <daniel.machon@microchip.com>
Reviewed-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Link: https://patch.msgid.link/20260212-sparx5-ptp-max-adj-v2-v1-1-06b200e50ce3@microchip.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a68a9bd086 ]
wait_for_port() can wait up to 2 seconds with the sleep and the polling
in wait_local_port_listen() combined. So, in netcons_basic.sh, the socat
process could die before the test writes to the netconsole.
Increase the timeout to 3 seconds to make netcons_basic.sh pass
consistently.
Fixes: 3dc6c76391 ("selftests: net: Add IPv6 support to netconsole basic tests")
Signed-off-by: Pin-yen Lin <treapking@google.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20260210005939.3230550-1-treapking@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e3b8cbf40c ]
This removes some noise that can be distracting while looking at
selftests by redirecting socat stderr to /dev/null.
Before this commit, netcons_basic would output:
Running with target mode: basic (ipv6)
2025/11/29 12:08:03 socat[259] W exiting on signal 15
2025/11/29 12:08:03 socat[271] W exiting on signal 15
basic : ipv6 : Test passed
Running with target mode: basic (ipv4)
2025/11/29 12:08:05 socat[329] W exiting on signal 15
2025/11/29 12:08:05 socat[322] W exiting on signal 15
basic : ipv4 : Test passed
Running with target mode: extended (ipv6)
2025/11/29 12:08:08 socat[386] W exiting on signal 15
2025/11/29 12:08:08 socat[386] W exiting on signal 15
2025/11/29 12:08:08 socat[380] W exiting on signal 15
extended : ipv6 : Test passed
Running with target mode: extended (ipv4)
2025/11/29 12:08:10 socat[440] W exiting on signal 15
2025/11/29 12:08:10 socat[435] W exiting on signal 15
2025/11/29 12:08:10 socat[435] W exiting on signal 15
extended : ipv4 : Test passed
After these changes, output looks like:
Running with target mode: basic (ipv6)
basic : ipv6 : Test passed
Running with target mode: basic (ipv4)
basic : ipv4 : Test passed
Running with target mode: extended (ipv6)
extended : ipv6 : Test passed
Running with target mode: extended (ipv4)
extended : ipv4 : Test passed
Signed-off-by: Andre Carvalho <asantostc@gmail.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20251129-netcons-socat-noise-v1-1-605a0cea8fca@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Stable-dep-of: a68a9bd086 ("selftests: netconsole: Increase port listening timeout")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 026f6513c5 ]
ocelot_port_xmit_inj() calls ocelot_can_inject() and
ocelot_port_inject_frame() without holding the injection group lock.
Both functions contain lockdep_assert_held() for the injection lock,
and the correct caller felix_port_deferred_xmit() properly acquires
the lock using ocelot_lock_inj_grp() before calling these functions.
Add ocelot_lock_inj_grp()/ocelot_unlock_inj_grp() around the register
injection path to fix the missing lock protection. The FDMA path is not
affected as it uses its own locking mechanism.
Fixes: c5e12ac3be ("net: mscc: ocelot: serialize access to the injection/extraction groups")
Signed-off-by: Ziyi Guo <n7l8m4@u.northwestern.edu>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Link: https://patch.msgid.link/20260208225602.1339325-4-n7l8m4@u.northwestern.edu
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 47f79b20e7 ]
Split ocelot_port_xmit() into two separate functions:
- ocelot_port_xmit_fdma(): handles the FDMA injection path
- ocelot_port_xmit_inj(): handles the register-based injection path
The top-level ocelot_port_xmit() now dispatches to the appropriate
function based on the ocelot_fdma_enabled static key.
This is a pure refactor with no behavioral change. Separating the two
code paths makes each one simpler and prepares for adding proper locking
to the register injection path without affecting the FDMA path.
Signed-off-by: Ziyi Guo <n7l8m4@u.northwestern.edu>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Link: https://patch.msgid.link/20260208225602.1339325-3-n7l8m4@u.northwestern.edu
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Stable-dep-of: 026f6513c5 ("net: mscc: ocelot: add missing lock protection in ocelot_port_xmit_inj()")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 29372f07f7 ]
Extract the PTP timestamp handling logic from ocelot_port_xmit() into a
separate ocelot_xmit_timestamp() helper function. This is a pure
refactor with no behavioral change.
The helper returns false if the skb was consumed (freed) due to a
timestamp request failure, and true if the caller should continue with
frame injection. The rew_op value is returned via pointer.
This prepares for splitting ocelot_port_xmit() into separate FDMA and
register injection paths in a subsequent patch.
Signed-off-by: Ziyi Guo <n7l8m4@u.northwestern.edu>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Link: https://patch.msgid.link/20260208225602.1339325-2-n7l8m4@u.northwestern.edu
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Stable-dep-of: 026f6513c5 ("net: mscc: ocelot: add missing lock protection in ocelot_port_xmit_inj()")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6c28aa8dfd ]
DWRR (Deficit Weighted Round Robin) scheduling distributes bandwidth
across traffic classes based on per-queue cost values, where lower cost
means higher bandwidth share.
The SPX5_DWRR_COST_MAX constant is 63 (6 bits) but the hardware
register field HSCH_DWRR_ENTRY_DWRR_COST is GENMASK(24, 20), only
5 bits wide (max 31). This causes sparx5_weight_to_hw_cost() to
compute cost values that silently overflow via FIELD_PREP, resulting
in incorrect scheduling weights.
Set SPX5_DWRR_COST_MAX to 31 to match the hardware register width.
Fixes: 211225428d ("net: microchip: sparx5: add support for offloading ets qdisc")
Signed-off-by: Daniel Machon <daniel.machon@microchip.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20260210-sparx5-fix-dwrr-cost-max-v1-1-58fbdbc25652@microchip.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit babab1b42e ]
For GMAC4, when split header is enabled, in some rare cases, the
hardware does not fill buf2 of the first descriptor with payload.
Thus we cannot assume buf2 is always fully filled if it is not
the last descriptor. Otherwise, the length of buf2 of the second
descriptor will be calculated wrong and cause an oops:
Unable to handle kernel paging request at virtual address ffff00019246bfc0
...
x2 : 0000000000000040 x1 : ffff00019246bfc0 x0 : ffff00009246c000
Call trace:
dcache_inval_poc+0x28/0x58 (P)
dma_direct_sync_single_for_cpu+0x38/0x6c
__dma_sync_single_for_cpu+0x34/0x6c
stmmac_napi_poll_rx+0x8f0/0xb60
__napi_poll.constprop.0+0x30/0x144
net_rx_action+0x160/0x274
handle_softirqs+0x1b8/0x1fc
...
To fix this, the PL bit-field in RDES3 register is used for all
descriptors, whether it is the last descriptor or not.
Fixes: ec222003bd ("net: stmmac: Prepare to add Split Header support")
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Jie Zhang <jie.zhang@analog.com>
Link: https://patch.msgid.link/20260209225037.589130-1-jie.zhang@analog.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 26ab9830be ]
Replace the has_gmac, has_gmac4 and has_xgmac ints, of which only one
can be set when matching a core to its driver backend, with an
enumerated type carrying the DWMAC core type.
Tested-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Acked-by: Chen-Yu Tsai <wens@kernel.org>
Reviewed-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Tested-by: Mohd Ayaan Anwar <mohd.anwar@oss.qualcomm.com>
Reviewed-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Link: https://patch.msgid.link/E1vB6ld-0000000BIPy-2Qi4@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Stable-dep-of: babab1b42e ("net: stmmac: fix oops when split header is enabled")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 813882ae22 ]
Changing the netif_carrier_*() state behind phylink's back has always
been prohibited because it messes up with phylinks state tracking, and
means that phylink no longer guarantees to call the mac_link_down()
and mac_link_up() methods at the appropriate times. This was later
documented in the sfp-phylink network driver conversion guide.
stmmac was converted to phylink in 2019, but nothing was done with the
"PCS" code. Since then, apart from the updates as part of phylink
development, nothing has happened with stmmac to improve its use of
phylink, or even to address this point.
A couple of years ago, a has_integrated_pcs boolean was added by Bart,
which later became the STMMAC_FLAG_HAS_INTEGRATED_PCS flag, to avoid
manipulating the netif_carrier_*() state. This flag is mis-named,
because whenever the stmmac is synthesized for its native SGMII, TBI
or RTBI interfaces, it has an "integrated PCS". This boolean/flag
actually means "ignore the status from the integrated PCS".
Discussing with Bart, the reasons for this are lost to the winds of
time (which is why we should always document the reasons in the commit
message.)
RGMII also has in-band status, and the dwmac cores and stmmac code
supports this but with one bug that saves the day.
When dwmac cores are synthesised for RGMII only, they do not contain
an integrated PCS, and so priv->dma_cap.pcs is clear, which prevents
(incorrectly) the "RGMII PCS" being used, meaning we don't read the
in-band status. However, a core synthesised for RGMII and also SGMII,
TBI or RTBI will have this capability bit set, thus making these
code paths reachable.
The Jetson Xavier NX uses RGMII mode to talk to its PHY, and removing
the incorrect check for priv->dma_cap.pcs reveals the theortical issue
with netif_carrier_*() manipulation is real:
dwc-eth-dwmac 2490000.ethernet eth0: Register MEM_TYPE_PAGE_POOL RxQ-0
dwc-eth-dwmac 2490000.ethernet eth0: PHY [stmmac-0:00] driver [RTL8211F Gigabit Ethernet] (irq=141)
dwc-eth-dwmac 2490000.ethernet eth0: No Safety Features support found
dwc-eth-dwmac 2490000.ethernet eth0: IEEE 1588-2008 Advanced Timestamp supported
dwc-eth-dwmac 2490000.ethernet eth0: registered PTP clock
dwc-eth-dwmac 2490000.ethernet eth0: configuring for phy/rgmii-id link mode
8021q: adding VLAN 0 to HW filter on device eth0
dwc-eth-dwmac 2490000.ethernet eth0: Adding VLAN ID 0 is not supported
Link is Up - 1000/Full
Link is Down
Link is Up - 1000/Full
This looks good until one realises that the phylink "Link" status
messages are missing, even when the RJ45 cable is reconnected. Nothing
one can do results in the interface working. The interrupt handler
(which prints those "Link is" messages) always wins over phylink's
resolve worker, meaning phylink never calls the mac_link_up() nor
mac_link_down() methods.
eth0 also sees no traffic received, and is unable to obtain a DHCP
address:
3: eth0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc mq state UP group defa
ult qlen 1000
link/ether e6:d3:6a:e6:92:de brd ff:ff:ff:ff:ff:ff
RX: bytes packets errors dropped overrun mcast
0 0 0 0 0 0
TX: bytes packets errors dropped carrier collsns
27686 149 0 0 0 0
With the STMMAC_FLAG_HAS_INTEGRATED_PCS flag set, which disables the
netif_carrier_*() manipulation then stmmac works normally:
dwc-eth-dwmac 2490000.ethernet eth0: Register MEM_TYPE_PAGE_POOL RxQ-0
dwc-eth-dwmac 2490000.ethernet eth0: PHY [stmmac-0:00] driver [RTL8211F Gigabit Ethernet] (irq=141)
dwc-eth-dwmac 2490000.ethernet eth0: No Safety Features support found
dwc-eth-dwmac 2490000.ethernet eth0: IEEE 1588-2008 Advanced Timestamp supported
dwc-eth-dwmac 2490000.ethernet eth0: registered PTP clock
dwc-eth-dwmac 2490000.ethernet eth0: configuring for phy/rgmii-id link mode
8021q: adding VLAN 0 to HW filter on device eth0
dwc-eth-dwmac 2490000.ethernet eth0: Adding VLAN ID 0 is not supported
Link is Up - 1000/Full
dwc-eth-dwmac 2490000.ethernet eth0: Link is Up - 1Gbps/Full - flow control rx/tx
and packets can be transferred.
This clearly shows that when priv->hw->pcs is set, but
STMMAC_FLAG_HAS_INTEGRATED_PCS is clear, the driver reliably fails.
Discovering whether a platform falls into this is impossible as
parsing all the dtsi and dts files to find out which use the stmmac
driver, whether any of them use RGMII or SGMII and also depends
whether an external interface is being used. The kernel likely
doesn't contain all dts files either.
The only driver that sets this flag uses the qcom,sa8775p-ethqos
compatible, and uses SGMII or 2500BASE-X.
but these are saved from this problem by the incorrect check for
priv->dma_cap.pcs.
So, we have to assume that for every other platform that uses SGMII
with stmmac is using an external PCS.
Moreover, ethtool output can be incorrect. With the full-duplex link
negotiated, ethtool reports:
Speed: 1000Mb/s
Duplex: Half
because with dwmac4, the full-duplex bit is in bit 16 of the status,
priv->xstats.pcs_duplex becomes BIT(16) for full duplex, but the
ethtool ksettings duplex member is u8 - so becomes zero. Moreover,
the supported, advertised and link partner modes are all "not
reported".
Finally, ksettings_set() won't be able to set the advertisement on
a PHY if this PCS code is activated, which is incorrect when SGMII
is used with a PHY.
Thus, remove:
1. the incorrect netif_carrier_*() manipulation.
2. the broken ethtool ksettings code.
Given that all uses of STMMAC_FLAG_HAS_INTEGRATED_PCS are now gone,
remove the flag from stmmac.h and dwmac-qcom-ethqos.c.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Tested-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Tested-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Link: https://patch.msgid.link/E1v9P5y-0000000AolC-1QWH@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Stable-dep-of: babab1b42e ("net: stmmac: fix oops when split header is enabled")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a2646773a0 ]
As explained in [1], iproute2 started rejecting tc-police burst sizes
that result in an overflow. This can happen when the burst size is high
enough and the rate is low enough.
A couple of test cases specify such configurations, resulting in
iproute2 errors and test failure.
Fix by reducing the burst size so that the test will pass with both new
and old iproute2 versions.
[1] https://lore.kernel.org/netdev/20250916215731.3431465-1-jay.vosburgh@canonical.com/
Fixes: cb12d17632 ("selftests: mlxsw: tc_restrictions: Test tc-police restrictions")
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/88b00c6e85188aa6a065dc240206119b328c46e1.1770643998.git.petrm@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b660b13d4c ]
In ovpn_net_xmit, after GSO segmentation and segment processing, the
first segment on the list is used to increment VPN TX statistics, which
fails to account for any subsequent segments in the chain.
Fix this by accumulating the length of every segment that successfully
passes skb_share_check into a tx_bytes variable. This ensures the peer
statistics accurately reflect the total data volume sent, regardless of
whether the original packet was segmented.
Fixes: 04ca14955f ("ovpn: store tunnel and transport statistics")
Signed-off-by: Ralf Lici <ralf@mandelbit.com>
Reviewed-by: Sabrina Dubroca <sd@queasysnail.net>
Signed-off-by: Antonio Quartulli <antonio@openvpn.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a5ec7baa44 ]
When building the skb_list in ovpn_net_xmit, skb_share_check will free
the original skb if it is shared. The current implementation continues
to use the stale skb pointer for subsequent operations:
- peer lookup,
- skb_dst_drop (even though all segments produced by skb_gso_segment
will have a dst attached),
- ovpn_peer_stats_increment_tx.
Fix this by moving the peer lookup and skb_dst_drop before segmentation
so that the original skb is still valid when used. Return early if all
segments fail skb_share_check and the list ends up empty.
Also switch ovpn_peer_stats_increment_tx to use skb_list.next; the next
patch fixes the stats logic.
Fixes: 08857b5ec5 ("ovpn: implement basic TX path (UDP)")
Signed-off-by: Ralf Lici <ralf@mandelbit.com>
Reviewed-by: Sabrina Dubroca <sd@queasysnail.net>
Signed-off-by: Antonio Quartulli <antonio@openvpn.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 93686c472e ]
During initialization, we override socket callbacks and set sk_user_data
to an ovpn_socket instance. Currently, these two operations are
decoupled: callbacks are overridden before sk_user_data is set. While
existing callbacks perform safety checks for NULL or non-ovpn
sk_user_data, this condition causes a "half-formed" state where valid
packets arriving during attachment trigger error logs (e.g., "invoked on
non ovpn socket").
Set sk_user_data before overriding the callbacks so that it can be
accessed safely from them. Since we already check that the socket has no
sk_user_data before setting it, this remains safe even if an interrupt
accesses the socket after sk_user_data is set but before the callbacks
are overridden.
This also requires initializing all protocol-specific fields (such as
tcp_tx_work and peer links) before calling ovpn_socket_attach, ensuring
the ovpn_socket is fully formed before it becomes visible to any
callback.
Fixes: f6226ae7a0 ("ovpn: introduce the ovpn_socket object")
Signed-off-by: Ralf Lici <ralf@mandelbit.com>
Reviewed-by: Sabrina Dubroca <sd@queasysnail.net>
Signed-off-by: Antonio Quartulli <antonio@openvpn.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e5c9ffc6ae ]
On certain platforms (PowerNV systems without a power-mgt DT node),
cpuidle may register only a single idle state. In cases where that
single state is a polling state (state 0), the ladder governor may
incorrectly treat state 1 as the first usable state and pass an
out-of-bounds index. This can lead to a NULL enter callback being
invoked, ultimately resulting in a system crash.
[ 13.342636] cpuidle-powernv : Only Snooze is available
[ 13.351854] Faulting instruction address: 0x00000000
[ 13.376489] NIP [0000000000000000] 0x0
[ 13.378351] LR [c000000001e01974] cpuidle_enter_state+0x2c4/0x668
Fix this by adding a bail-out in cpuidle_select() that returns state 0
directly when state_count <= 1, bypassing the governor and keeping the
tick running.
Fixes: dc2251bf98 ("cpuidle: Eliminate the CPUIDLE_DRIVER_STATE_START symbol")
Signed-off-by: Aboorva Devarajan <aboorvad@linux.ibm.com>
Reviewed-by: Christian Loehle <christian.loehle@arm.com>
Link: https://patch.msgid.link/20260216185005.1131593-2-aboorvad@linux.ibm.com
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit cd7ef20ba8 ]
On the THUNDEROBOT ZERO laptop, the second NVMe slot and the discrete
NVIDIA GPU are both controlled by power-resource PXP. Due to the SSDT table
bug (lack of reference), PXP will be shut dow as an "unused" power resource
during initialization, making the NVMe slot #2 + NVIDIA both inaccessible.
This issue was introduced by commit a1224f34d7 ("ACPI: PM: Check
states of power resources during initialization"). Here are test
results on the three consecutive commits:
(bad again!) a1224f34d7 ACPI: PM: Check states of power resources during initialization
(good) bc28368596 ACPI: PM: Do not turn off power resources in unknown state
(bad) 519d81956e Linux 5.15-rc6
On commit bc28368596 ("ACPI: PM: Do not turn off power resources in
unknown state") this was not an issue because the power resource state
left UNKNOWN thus being ignored.
See also commit 9b04d99788 ("ACPI: PM: Do not turn of unused power
resources on the Toshiba Click Mini") which is another almost identical
case to this one.
Fixes: a1224f34d7 ("ACPI: PM: Check states of power resources during initialization")
Closes: https://bugzilla.kernel.org/show_bug.cgi?id=221087
Signed-off-by: Zhai Can <bczhc0@126.com>
Link: https://patch.msgid.link/20260214161452.2849346-1-bczhc0@126.com
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5ed4b6b37c ]
objpool uses struct objpool_head to store metadata information, and its
cpu_slots member points to an array of pointers that store the addresses
of the percpu ring arrays. However, the memory size allocated during the
initialization of cpu_slots is nr_cpu_ids * sizeof(struct objpool_slot).
On a 64-bit machine, the size of struct objpool_slot is 16 bytes, which is
twice the size of the actual pointer required, and the extra memory is
never be used, resulting in a waste of memory. Therefore, the memory size
required for cpu_slots needs to be corrected.
Link: https://lkml.kernel.org/r/20260202132846.68257-1-zhouwenhao7600@gmail.com
Fixes: b4edb8d2d4 ("lib: objpool added: ring-array based lockless MPMC")
Signed-off-by: zhouwenhao <zhouwenhao7600@gmail.com>
Reviewed-by: Andrew Morton <akpm@linux-foundation.org>
Cc: "Masami Hiramatsu (Google)" <mhiramat@kernel.org>
Cc: Matt Wu <wuqiang.matt@bytedance.com>
Cc: wuqiang.matt <wuqiang.matt@bytedance.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b24335521d ]
selftests/memfd: use IPC semaphore instead of SIGSTOP/SIGCONT
In order to synchronize new processes to test inheritance of memfd_noexec
sysctl, memfd_test sets up the sysctl with a value before creating the new
process. The new process then sends itself a SIGSTOP in order to wait for
the parent to flip the sysctl value and send a SIGCONT signal.
This would work as intended if it wasn't the fact that the new process is
being created with CLONE_NEWPID, which creates a new PID namespace and the
new process has PID 1 in this namespace. There're restrictions on sending
signals to PID 1 and, although it's relaxed for other than root PID
namespace, it's biting us here. In this specific case the SIGSTOP sent by
the new process is ignored (no error to kill() is returned) and it never
stops its execution. This is usually not noticiable as the parent usually
manages to set the new sysctl value before the child has a chance to run
and the test succeeds. But if you run the test in a loop, it eventually
reproduces:
while [ 1 ]; do ./memfd_test >log 2>&1 || break; done; cat log
So this patch replaces the SIGSTOP/SIGCONT synchronization with IPC
semaphore.
Link: https://lkml.kernel.org/r/a7776389-b3d6-4b18-b438-0b0e3ed1fd3b@work
Fixes: 6469b66e3f ("selftests: improve vm.memfd_noexec sysctl tests")
Signed-off-by: Aristeu Rozanski <aris@redhat.com>
Cc: Aleksa Sarai <cyphar@cyphar.com>
Cc: Shuah Khan <shuah@kernel.org>
Cc: liuye <liuye@kylinos.cn>
Cc: Lorenzo Stoakes <lorenzo.stoakes@oracle.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c7d54dafa0 ]
On partitioned systems, multiple TPMI instances may exist per package,
but RAPL registers are only valid on one instance since RAPL has
package-scope control. Other instances return invalid versions during
domain parsing, which is expected behavior on such systems.
Currently this generates a firmware bug warning:
intel_rapl_tpmi: [Firmware Bug]: Invalid version
Remove the FW_BUG tag, downgrade to pr_debug(), and update the message
to clarify that invalid versions are expected on partitioned systems
where only one instance can be valid.
Fixes: 9eef7f9da9 ("powercap: intel_rapl: Introduce RAPL TPMI interface driver")
Reported-by: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Kuppuswamy Sathyanarayanan <sathyanarayanan.kuppuswamy@linux.intel.com>
Reviewed-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Link: https://patch.msgid.link/20260211223401.1575776-1-sathyanarayanan.kuppuswamy@linux.intel.com
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 56eb0c0ed3 ]
per_cpu(cpc_desc_ptr, cpu) object is initialized for only the online
CPUs via acpi_soft_cpu_online() --> __acpi_processor_start() -->
acpi_cppc_processor_probe().
However, send_pcc_cmd() and acpi_get_psd_map() still iterate over all
possible CPUs. In acpi_get_psd_map(), encountering an offline CPU
returns -EFAULT, causing cppc_cpufreq initialization to fail.
This breaks systems booted with "nosmt" or "nosmt=force".
Fix by using for_each_online_cpu() in both functions.
Fixes: 80b8286aee ("ACPI / CPPC: support for batching CPPC requests")
Signed-off-by: Sean V Kelley <skelley@nvidia.com>
Link: https://patch.msgid.link/20260211212254.30190-1-skelley@nvidia.com
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b2bc7c44ed ]
In the 'DeleteIndexEntryRoot' case of the 'do_action' function, the
entry size ('esize') is retrieved from the log record without adequate
bounds checking.
Specifically, the code calculates the end of the entry ('e2') using:
e2 = Add2Ptr(e1, esize);
It then calculates the size for memmove using 'PtrOffset(e2, ...)',
which subtracts the end pointer from the buffer limit. If 'esize' is
maliciously large, 'e2' exceeds the used buffer size. This results in
a negative offset which, when cast to size_t for memmove, interprets
as a massive unsigned integer, leading to a heap buffer overflow.
This commit adds a check to ensure that the entry size ('esize') strictly
fits within the remaining used space of the index header before performing
memory operations.
Fixes: b46acd6a6a ("fs/ntfs3: Add NTFS journal")
Signed-off-by: Jiasheng Jiang <jiashengjiangcool@gmail.com>
Signed-off-by: Konstantin Komarov <almaz.alexandrovich@paragon-software.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 27b75ca4e5 ]
When processing valid within the range [valid : pos), if valid cannot
be retrieved correctly, for example, if the retrieved valid value is
always the same, this can trigger a potential infinite loop, similar
to the hung problem reported by syzbot [1].
Adding a check for the valid value within the loop body, and terminating
the loop and returning -EINVAL if the value is the same as the current
value, can prevent this.
[1]
INFO: task syz.4.21:6056 blocked for more than 143 seconds.
Call Trace:
rwbase_write_lock+0x14f/0x750 kernel/locking/rwbase_rt.c:244
inode_lock include/linux/fs.h:1027 [inline]
ntfs_file_write_iter+0xe6/0x870 fs/ntfs3/file.c:1284
Fixes: 4342306f0f ("fs/ntfs3: Add file operations and implementation")
Reported-by: syzbot+bcf9e1868c1a0c7e04f1@syzkaller.appspotmail.com
Closes: https://syzkaller.appspot.com/bug?extid=bcf9e1868c1a0c7e04f1
Signed-off-by: Edward Adam Davis <eadavis@qq.com>
Signed-off-by: Konstantin Komarov <almaz.alexandrovich@paragon-software.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f223ebffa1 ]
KMSAN reports an uninitialized value in longest_match_std(), invoked
from ntfs_compress_write(). When new folios are allocated without being
marked uptodate and ni_read_frame() is skipped because the caller expects
the frame to be completely overwritten, some reserved folios may remain
only partially filled, leaving the rest memory uninitialized.
Fixes: 584f60ba22 ("ntfs3: Convert ntfs_get_frame_pages() to use a folio")
Tested-by: syzbot+08d8956768c96a2c52cf@syzkaller.appspotmail.com
Reported-by: syzbot+08d8956768c96a2c52cf@syzkaller.appspotmail.com
Closes: https://syzkaller.appspot.com/bug?extid=08d8956768c96a2c52cf
Signed-off-by: Bartlomiej Kubik <kubik.bartlomiej@gmail.com>
Signed-off-by: Konstantin Komarov <almaz.alexandrovich@paragon-software.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 22dbb0987b ]
By having them share the same space in struct io_cancel_data, it ends up
disallowing IORING_ASYNC_CANCEL_FD|IORING_ASYNC_CANCEL_USERDATA from
working. Eg you cannot match on both a file and user_data for
cancelation purposes. This obviously isn't a common use case as nobody
has reported this, but it does result in -ENOENT potentially being
returned when trying to match on both, rather than actually doing what
the API says it would.
Fixes: 4bf94615b8 ("io_uring: allow IORING_OP_ASYNC_CANCEL with 'fd' key")
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 56112578c7 ]
io_key_has_sqarray static branch can be easily switched on/off by the
user every time patching the kernel. That can be very disruptive as it
might require heavy synchronisation across all CPUs. Use deferred static
keys, which can rate-limit it by deferring, batching and potentially
effectively eliminating dec+inc pairs.
Fixes: 9b296c625a ("io_uring: static_key for !IORING_SETUP_NO_SQARRAY")
Signed-off-by: Pavel Begunkov <asml.silence@gmail.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2ebc8d600f ]
DRBD requires stable pages because it may read the same bio data
multiple times for local disk I/O and network transmission, and in
some cases for calculating checksums.
The BLK_FEAT_STABLE_WRITES flag is set when the device is first
created, but blk_set_stacking_limits() clears it whenever a
backing device is attached. In some cases the flag may be
inherited from the backing device, but we want it to be enabled
at all times.
Unconditionally re-enable BLK_FEAT_STABLE_WRITES in
drbd_reconsider_queue_parameters() after the queue parameter
negotiations.
Also, document why we want this flag enabled in the first place.
Fixes: 1a02f3a73f ("block: move the stable_writes flag to queue_limits")
Signed-off-by: Christoph Böhmwalder <christoph.boehmwalder@linbit.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 666c53e94c ]
The clocks in fsl_edma_engine::muxclk are allocated and enabled with
devm_clk_get_enabled(), which automatically cleans these resources up,
but these clocks are also manually disabled in fsl_edma_remove(). This
causes warnings on driver removal for each clock:
edma_module already disabled
WARNING: CPU: 0 PID: 418 at drivers/clk/clk.c:1200 clk_core_disable+0x198/0x1c8
[...]
Call trace:
clk_core_disable+0x198/0x1c8 (P)
clk_disable+0x34/0x58
fsl_edma_remove+0x74/0xe8 [fsl_edma]
[...]
---[ end trace 0000000000000000 ]---
edma_module already unprepared
WARNING: CPU: 0 PID: 418 at drivers/clk/clk.c:1059 clk_core_unprepare+0x1f8/0x220
[...]
Call trace:
clk_core_unprepare+0x1f8/0x220 (P)
clk_unprepare+0x34/0x58
fsl_edma_remove+0x7c/0xe8 [fsl_edma]
[...]
---[ end trace 0000000000000000 ]---
Fix these warnings by removing the unnecessary fsl_disable_clocks() call
in fsl_edma_remove().
Fixes: a9903de3aa ("dmaengine: fsl-edma: refactor using devm_clk_get_enabled")
Signed-off-by: Jared Kangas <jkangas@redhat.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Link: https://patch.msgid.link/20260113-fsl-edma-clock-removal-v1-1-2025b49e7bcc@redhat.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
