[ Upstream commit af3145aa14 ]
This reverts commit 330140d731
200ms delay will cause panel display image later than backlight
turn on, revert this patch.
Fixes: 330140d731 ("drm/bridge: Add 200ms delay to wait FW HPD status stable")
Signed-off-by: Xin Ji <xji@analogixsemi.com>
Reviewed-by: Robert Foss <rfoss@kernel.org>
Signed-off-by: Robert Foss <rfoss@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20231120091038.284825-1-xji@analogixsemi.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 53edb54956 ]
As Al reported in link[1]:
f2fs_rename()
...
if (old_dir != new_dir && !whiteout)
f2fs_set_link(old_inode, old_dir_entry,
old_dir_page, new_dir);
else
f2fs_put_page(old_dir_page, 0);
You want correct inumber in the ".." link. And cross-directory
rename does move the source to new parent, even if you'd been asked
to leave a whiteout in the old place.
[1] https://lore.kernel.org/all/20231017055040.GN800259@ZenIV/
With below testcase, it may cause dirent corruption, due to it missed
to call f2fs_set_link() to update ".." link to new directory.
- mkdir -p dir/foo
- renameat2 -w dir/foo bar
[ASSERT] (__chk_dots_dentries:1421) --> Bad inode number[0x4] for '..', parent parent ino is [0x3]
[FSCK] other corrupted bugs [Fail]
Fixes: 7e01e7ad74 ("f2fs: support RENAME_WHITEOUT")
Cc: Jan Kara <jack@suse.cz>
Reported-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Chao Yu <chao@kernel.org>
Reviewed-by: Jan Kara <jack@suse.cz>
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f033c87fda ]
Starting with commit f6038de293 ("arm64: dts: imx8qm: Fix VPU core
alias name") the alias for VPU cores uses dashes instead of underscores.
Adjust the alias stem accordingly. Fixes the errors:
amphion-vpu-core 2d040000.vpu-core: can't get vpu core id
amphion-vpu-core 2d050000.vpu-core: can't get vpu core id
Fixes: f6038de293 ("arm64: dts: imx8qm: Fix VPU core alias name")
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Reviewed-by: Ming Qian <ming.qian@nxp.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1fb7b5ab62 ]
The (TRY_)DECODER_CMD ioctls are used to support flushing when holding
capture buffers is supported. This is the case of this driver but the
ioctls were never hooked to the ioctl ops.
Add them to correctly support flushing.
Fixes: ed7bb87d3d ("media: rkvdec: Enable capture buffer holding for H264")
Signed-off-by: Paul Kocialkowski <paul.kocialkowski@bootlin.com>
Reviewed-by: Daniel Almeida <daniel.almeida@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6c0d9e12b1 ]
The (TRY_)DECODER_CMD ioctls are used to support flushing when holding
capture buffers is supported. This is the case of this driver but the
ioctls were never hooked to the ioctl ops.
Add them to correctly support flushing.
Fixes: 340ce50f75 ("media: hantro: Enable HOLD_CAPTURE_BUF for H.264")
Signed-off-by: Paul Kocialkowski <paul.kocialkowski@bootlin.com>
Reviewed-by: Daniel Almeida <daniel.almeida@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3907f6ef8e ]
The (TRY_)DECODER_CMD ioctls are used to support flushing when holding
capture buffers is supported. This is the case of this driver but the
ioctls were never hooked to the ioctl ops.
Add them to correctly support flushing.
Fixes: 0c078e310b ("media: visl: add virtual stateless decoder driver")
Signed-off-by: Paul Kocialkowski <paul.kocialkowski@bootlin.com>
Reviewed-by: Daniel Almeida <daniel.almeida@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d8212c5c87 ]
This patch reverts commit c677d7ae83
("media: mtk-jpeg: Fix use after free bug due to uncanceled work").
The job_timeout_work is initialized only for
the single-core JPEG device so it will cause the crash for multi-core
JPEG devices.
Fix it by removing the cancel_delayed_work_sync function.
Fixes: c677d7ae83 ("media: mtk-jpeg: Fix use after free bug due to uncanceled work")
Signed-off-by: Zheng Wang <zyytlz.wz@163.com>
Signed-off-by: Dmitry Osipenko <dmitry.osipenko@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ded85b0c0e ]
Upon module load, a kthread is created targeting the
pvr2_context_thread_func function, which may call pvr2_context_destroy
and thus call kfree() on the context object. However, that might happen
before the usb hub_event handler is able to notify the driver. This
patch adds a sanity check before the invalid read reported by syzbot,
within the context disconnection call stack.
Reported-and-tested-by: syzbot+621409285c4156a009b3@syzkaller.appspotmail.com
Closes: https://lore.kernel.org/all/000000000000a02a4205fff8eb92@google.com/
Fixes: e5be15c638 ("V4L/DVB (7711): pvrusb2: Fix race on module unload")
Signed-off-by: Ricardo B. Marliere <ricardo@marliere.net>
Acked-by: Mike Isely <isely@pobox.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 38360bf96d ]
The driver only frees the reserved irq if priv->irq_enabled is set to
true. However, the driver mistakenly sets priv->irq_enabled to false,
instead of true, in tilcdc_irq_install(), and thus the driver never
frees the irq, causing issues on loading the driver a second time.
Fixes: b6366814fa ("drm/tilcdc: Convert to Linux IRQ interfaces")
Cc: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Aradhya Bhatia <a-bhatia1@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230919-lcdc-v1-1-ba60da7421e1@ideasonboard.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ce3e112e7a ]
With tpd12s015_remove() marked with __exit this function is discarded
when the driver is compiled as a built-in. The result is that when the
driver unbinds there is no cleanup done which results in resource
leakage or worse.
Fixes: cff5e6f7e8 ("drm/bridge: Add driver for the TI TPD12S015 HDMI level shifter")
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Link: https://patchwork.freedesktop.org/patch/msgid/20231102165640.3307820-19-u.kleine-koenig@pengutronix.de
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5f35a624c1 ]
Fix a sparse warning with this message
"warning:dereference of noderef expression". In this context it means we
are dereferencing a __rcu tagged pointer directly.
We should not be directly dereferencing a rcu pointer. To get a normal
(non __rcu tagged pointer) from a __rcu tagged pointer we are using the
function unrcu_pointer(...). The non __rcu tagged pointer then can be
dereferenced just like a normal pointer.
I tested with qemu with this command
qemu-system-x86_64 \
-m 2G \
-smp 2 \
-kernel bzImage \
-append "console=ttyS0 root=/dev/sda earlyprintk=serial net.ifnames=0" \
-drive file=bullseye.img,format=raw \
-net user,host=10.0.2.10,hostfwd=tcp:127.0.0.1:10021-:22 \
-net nic,model=e1000 \
-enable-kvm \
-nographic \
-pidfile vm.pid \
2>&1 | tee vm.log
with lockdep enabled.
Fixes: 0ec5f02f0e ("drm/nouveau: prevent stale fence->channel pointers, and protect with rcu")
Signed-off-by: Abhinav Singh <singhabhinav9051571833@gmail.com>
Signed-off-by: Danilo Krummrich <dakr@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20231113191303.3277733-1-singhabhinav9051571833@gmail.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 03c5b2a5f6 ]
For devices like the Anbernic RG351M and RG351P the panel is wired to
an always on regulator. When the device suspends and wakes up, there
are some slight artifacts on the screen that go away over time. If
instead we hold the panel in reset status after it is unprepared,
this does not happen.
Fixes: 5b6603360c ("drm/panel: add panel driver for Elida KD35T133 panels")
Signed-off-by: Chris Morgan <macromorgan@hotmail.com>
Reviewed-by: Jessica Zhang <quic_jesszhan@quicinc.com>
Link: https://lore.kernel.org/r/20231117194405.1386265-3-macroalpha82@gmail.com
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20231117194405.1386265-3-macroalpha82@gmail.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f45b83ad39 ]
EOPNOTSUPP is more situable than EINVAL for allocating XRCD while XRC
is not supported and unsupported resizing SRQ.
Fixes: 32548870d4 ("RDMA/hns: Add support for XRC on HIP09")
Fixes: 221109e643 ("RDMA/hns: Add interception for resizing SRQs")
Signed-off-by: Junxian Huang <huangjunxian6@hisilicon.com>
Link: https://lore.kernel.org/r/20231114123449.1106162-2-huangjunxian6@hisilicon.com
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b9a85e5eec ]
The patch 1da177e4c3: "Linux-2.6.12-rc2" from Apr 16, 2005
(linux-next), leads to the following Smatch static checker warning:
drivers/infiniband/hw/mthca/mthca_cmd.c:644 mthca_SYS_EN()
error: uninitialized symbol 'out'.
drivers/infiniband/hw/mthca/mthca_cmd.c
636 int mthca_SYS_EN(struct mthca_dev *dev)
637 {
638 u64 out;
639 int ret;
640
641 ret = mthca_cmd_imm(dev, 0, &out, 0, 0, CMD_SYS_EN, CMD_TIME_CLASS_D);
We pass out here and it gets used without being initialized.
err = mthca_cmd_post(dev, in_param,
out_param ? *out_param : 0,
^^^^^^^^^^
in_modifier, op_modifier,
op, context->token, 1);
It's the same in mthca_cmd_wait() and mthca_cmd_poll().
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Reported-by: Dan Carpenter <dan.carpenter@linaro.org>
Closes: https://lore.kernel.org/all/533bc3df-8078-4397-b93d-d1f6cec9b636@moroto.mountain
Link: https://lore.kernel.org/r/c559cb7113158c02d75401ac162652072ef1b5f0.1699867650.git.leon@kernel.org
Signed-off-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 22aa1a2090 ]
The layout of the registers {TILER,SHADER,L2}_PWROFF_LO, used to request
powering off cores, is the same as the {TILER,SHADER,L2}_PWRON_LO ones:
this means that in order to request poweroff of cores, we are supposed
to write a bitmask of cores that should be powered off!
This means that the panfrost_gpu_power_off() function has always been
doing nothing.
Fix powering off the GPU by writing a bitmask of the cores to poweroff
to the relevant PWROFF_LO registers and then check that the transition
(from ON to OFF) has finished by polling the relevant PWRTRANS_LO
registers.
While at it, in order to avoid code duplication, move the core mask
logic from panfrost_gpu_power_on() to a new panfrost_get_core_mask()
function, used in both poweron and poweroff.
Fixes: f3ba91228e ("drm/panfrost: Add initial panfrost driver")
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Reviewed-by: Steven Price <steven.price@arm.com>
Signed-off-by: Steven Price <steven.price@arm.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20231102141507.73481-1-angelogioacchino.delregno@collabora.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7707dd6022 ]
The current code does '(bpp << 4) / 16' in the MST PBN
calculation, but that is just the same as 'bpp' so the
DSC codepath achieves absolutely nothing. Fix it up so that
the fractional part of the bpp value is actually used instead
of truncated away. 64*1006 has enough zero lsbs that we can
just shift that down in the dividend and thus still manage
to stick to a 32bit divisor.
And while touching this, let's just make the whole thing more
straightforward by making the passed in bpp value .4 binary
fixed point always, instead of having to pass in different
things based on whether DSC is enabled or not.
v2:
- Fix DSC kunit test cases.
Cc: Manasi Navare <manasi.d.navare@intel.com>
Cc: Lyude Paul <lyude@redhat.com>
Cc: Harry Wentland <harry.wentland@amd.com>
Cc: David Francis <David.Francis@amd.com>
Cc: Mikita Lipski <mikita.lipski@amd.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Fixes: dc48529fb1 ("drm/dp_mst: Add PBN calculation for DSC modes")
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
[Imre: Fix kunit test cases]
Acked-by: Maxime Ripard <mripard@kernel.org>
Reviewed-by: Lyude Paul <lyude@redhat.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20231030155843.2251023-3-imre.deak@intel.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 501069dad5 ]
As a preparation for Xe we want to remove all i915_gem_object details away
from frontbuffer tacking code. Due to this move releasing gem object
reference to i915_gem_object_set_frontbuffer.
Signed-off-by: Jouni Högander <jouni.hogander@intel.com>
Reviewed-by: Juha-Pekka Heikkila <juhapekka.heikkila@gmail.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20231012072158.4115795-2-jouni.hogander@intel.com
Stable-dep-of: 560ea72c76 ("drm/i915/dp_mst: Fix race between connector registration and setup")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 40974ee421 ]
The select was lost by accident during the multiplatform conversion.
Any davinci-only
arm-linux-gnueabi-ld: arch/arm/mach-davinci/sleep.o: in function `CACHE_FLUSH':
(.text+0x168): undefined reference to `arm926_flush_kern_cache_all'
Fixes: f962396ce2 ("ARM: davinci: support multiplatform build for ARM v5")
Acked-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Link: https://lore.kernel.org/r/20240108110055.1531153-1-arnd@kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4fc68c4c1a ]
Fix rxrpc_cleanup_ring() to use rxrpc_purge_queue() rather than
skb_queue_purge() so that the count of outstanding skbuffs is correctly
updated when a failed call is cleaned up.
Without this rmmod may hang waiting for rxrpc_n_rx_skbs to become zero.
Fixes: 5d7edbc923 ("rxrpc: Get rid of the Rx ring")
Reported-by: Marc Dionne <marc.dionne@auristor.com>
Signed-off-by: David Howells <dhowells@redhat.com>
cc: "David S. Miller" <davem@davemloft.net>
cc: Eric Dumazet <edumazet@google.com>
cc: Jakub Kicinski <kuba@kernel.org>
cc: Paolo Abeni <pabeni@redhat.com>
cc: linux-afs@lists.infradead.org
cc: netdev@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a460f4a684 ]
At the moment, the GigE port is enabled in the mlxbf_gige_probe
function. If the mlxbf_gige_open is not executed, this could cause
pause frames to increase in the case where there is high backgroud
traffic. This results in clogging the port.
So move enabling the OOB port to mlxbf_gige_open.
Fixes: f92e1869d7 ("Add Mellanox BlueField Gigabit Ethernet driver")
Reviewed-by: David Thompson <davthompson@nvidia.com>
Signed-off-by: Asmaa Mnebhi <asmaa@nvidia.com>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ef210ef85d ]
Although the link is up, there is no ip assigned on setups with high background
traffic. Nothing is transmitted nor received. The RX error count keeps on
increasing. After several minutes, the RX error count stagnates and the
GigE interface finally gets an ip.
The issue is that mlxbf_gige_rx_init() is called before phy_start().
As soon as the RX DMA is enabled in mlxbf_gige_rx_init(), the RX CI reaches the max
of 128, and becomes equal to RX PI. RX CI doesn't decrease since the code hasn't
ran phy_start yet.
Bring the PHY up before starting the RX.
Fixes: f92e1869d7 ("Add Mellanox BlueField Gigabit Ethernet driver")
Reviewed-by: David Thompson <davthompson@nvidia.com>
Signed-off-by: Asmaa Mnebhi <asmaa@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 393cd8ffd8 ]
blkg_lookup() is called with either queue_lock or rcu read lock, so
use rcu_dereference_check(lockdep_is_held(&q->queue_lock)) for
retrieving 'blkg', which way models the check exactly for covering
queue lock or rcu read lock.
Fix lockdep warning of "block/blk-cgroup.h:254 suspicious rcu_dereference_check() usage!"
from blkg_lookup().
Tested-by: Changhui Zhong <czhong@redhat.com>
Signed-off-by: Ming Lei <ming.lei@redhat.com>
Reviewed-by: Yu Kuai <yukuai3@huawei.com>
Fixes: 83462a6c97 ("blkcg: Drop unnecessary RCU read [un]locks from blkg_conf_prep/finish()")
Acked-by: Tejun Heo <tj@kernel.org>
Link: https://lore.kernel.org/r/20231219012833.2129540-1-ming.lei@redhat.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ecba66cb36 ]
The gotol implementation uses a wrong data type for the offset: it
should be s32, not s16.
Fixes: c690191e23 ("s390/bpf: Implement unconditional jump with 32-bit offset")
Signed-off-by: Ilya Leoshkevich <iii@linux.ibm.com>
Acked-by: Yonghong Song <yonghong.song@linux.dev>
Acked-by: John Fastabend <john.fastabend@gmail.com>
Link: https://lore.kernel.org/r/20240102193531.3169422-2-iii@linux.ibm.com
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a562c0a2d6 ]
Busy polling while holding the socket lock makes litle sense,
because incoming packets wont reach our receive queue.
Fixes: 8465a5fcd1 ("sctp: add support for busy polling to sctp protocol")
Reported-by: Jacob Moroni <jmoroni@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Cc: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4746b36b1a ]
For some reason sctp_poll() generates EPOLLERR if sk->sk_error_queue
is not empty but recvmsg() can not drain the error queue yet.
This is needed to better support timestamping.
I had to export inet_recv_error(), since sctp
can be compiled as a module.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Cc: Willem de Bruijn <willemb@google.com>
Acked-by: Xin Long <lucien.xin@gmail.com>
Link: https://lore.kernel.org/r/20231212145550.3872051-1-edumazet@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Stable-dep-of: a562c0a2d6 ("sctp: fix busy polling")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 16b2f26498 ]
When sockets are added to a sockmap or sockhash we allocate and init a
psock. Then update the proto ops with sock_map_init_proto the flow is
sock_hash_update_common
sock_map_link
psock = sock_map_psock_get_checked() <-returns existing psock
sock_map_init_proto(sk, psock) <- updates sk_proto
If the socket is already in a map this results in the sock_map_init_proto
being called multiple times on the same socket. We do this because when
a socket is added to multiple maps this might result in a new set of BPF
programs being attached to the socket requiring an updated ops struct.
This creates a rule where it must be safe to call psock_update_sk_prot
multiple times. When we added a fix for UAF through unix sockets in patch
4dd9a38a753fc we broke this rule by adding a sock_hold in that path
to ensure the sock is not released. The result is if a af_unix stream sock
is placed in multiple maps it results in a memory leak because we call
sock_hold multiple times with only a single sock_put on it.
Fixes: 8866730aed ("bpf, sockmap: af_unix stream sockets need to hold ref for pair sock")
Reported-by: Xingwei Lee <xrivendell7@gmail.com>
Signed-off-by: John Fastabend <john.fastabend@gmail.com>
Signed-off-by: Martin KaFai Lau <martin.lau@kernel.org>
Reviewed-by: Jakub Sitnicki <jakub@cloudflare.com>
Link: https://lore.kernel.org/r/20231221232327.43678-2-john.fastabend@gmail.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d18125b640 ]
A probe response from a transmitting AP in an Multi-BSSID setup will
contain more than one Multi-Link element. Most likely, only one of these
elements contains per-STA profiles.
Fixes: 2481b5da9c ("wifi: cfg80211: handle BSS data contained in ML probe responses")
Signed-off-by: Benjamin Berg <benjamin.berg@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20240102213313.6635eb152735.I94289002d4a2f7b6b44dfa428344854e37b0b29c@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2a0698f86d ]
The comment was referencing the wrong section of the documentation and
was also subtly wrong as it assumed the rules that apply when sending
probe requests directly to a nontransmitted AP. However, in that case
the response comes from the transmitting AP and the AP MLD ID will be
included.
Fixes: 2481b5da9c ("wifi: cfg80211: handle BSS data contained in ML probe responses")
Signed-off-by: Benjamin Berg <benjamin.berg@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20240102213313.0917ab4b5d7f.I76aff0e261a5de44ffb467e591a46597a30d7c0a@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9a9525de86 ]
null_blk has some rather odd capping of the max_hw_sectors value to
BLK_DEF_MAX_SECTORS, which doesn't make sense - max_hw_sector is the
hardware limit, and BLK_DEF_MAX_SECTORS despite the confusing name is the
default cap for the max_sectors field used for normal file system I/O.
Remove all the capping, and simply leave it to the block layer or
user to take up or not all of that for file system I/O.
Fixes: ea17fd354c ("null_blk: Allow controlling max_hw_sectors limit")
Signed-off-by: Christoph Hellwig <hch@lst.de>
Link: https://lore.kernel.org/r/20231227092305.279567-2-hch@lst.de
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 64057f051f ]
Serdev recv_buf() callback is supposed to return the amount of bytes
consumed, therefore an int in between 0 and count.
Do not return negative number in case of issue, just print an error and
return count. This fixes a WARN in ttyport_receive_buf().
Link: https://lore.kernel.org/all/087be419-ec6b-47ad-851a-5e1e3ea5cfcc@kernel.org/
Fixes: 7237c4c9ec ("Bluetooth: mediatek: Add protocol support for MediaTek serial devices")
Signed-off-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 94d0539425 ]
Serdev recv_buf() callback is supposed to return the amount of bytes
consumed, therefore an int in between 0 and count.
Do not return a negative number in case of issue, just print an error
and return count. Before this change, in case of error, the returned
negative number was internally converted to 0 in ttyport_receive_buf,
now when the receive buffer is corrupted we return the size of the whole
received data (`count`). This should allow for better recovery in case
receiver/transmitter get out of sync if some data is lost.
This fixes a WARN in ttyport_receive_buf().
Bluetooth: hci0: Frame reassembly failed (-84)
------------[ cut here ]------------
serial serial0: receive_buf returns -84 (count = 6)
WARNING: CPU: 0 PID: 37 at drivers/tty/serdev/serdev-ttyport.c:37 ttyport_receive_buf+0xd8/0xf8
Modules linked in: mwifiex_sdio(+) ...
CPU: 0 PID: 37 Comm: kworker/u4:2 Not tainted 6.7.0-rc2-00147-gf1a09972a45a #1
Hardware name: Toradex Verdin AM62 WB on Verdin Development Board (DT)
Workqueue: events_unbound flush_to_ldisc
pstate: 60000005 (nZCv daif -PAN -UAO -TCO -DIT -SSBS BTYPE=--)
pc : ttyport_receive_buf+0xd8/0xf8
lr : ttyport_receive_buf+0xd8/0xf8
...
Call trace:
ttyport_receive_buf+0xd8/0xf8
flush_to_ldisc+0xbc/0x1a4
process_scheduled_works+0x16c/0x28c
Closes: https://lore.kernel.org/all/ZWEIhcUXfutb5SY6@francesco-nb.int.toradex.com/
Fixes: 689ca16e52 ("Bluetooth: NXP: Add protocol support for NXP Bluetooth chipsets")
Signed-off-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d03376c185 ]
This reverts 19f8def031
"Bluetooth: Fix auth_complete_evt for legacy units" which seems to be
working around a bug on a broken controller rather then any limitation
imposed by the Bluetooth spec, in fact if there ws not possible to
re-auth the command shall fail not succeed.
Fixes: 19f8def031 ("Bluetooth: Fix auth_complete_evt for legacy units")
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit aaba7ddc85 ]
Parse netlink attribute containing the chain type in this update, to
bail out if this is different from the existing type.
Otherwise, it is possible to define a chain with the same name, hook and
priority but different type, which is silently ignored.
Fixes: 96518518cc ("netfilter: add nftables")
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 08e4c8c591 ]
If a transaction is aborted, we should mark the to-be-released NEWSET dead,
just like commit path does for DEL and DESTROYSET commands.
In both cases all remaining elements will be released via
set->ops->destroy().
The existing abort code does NOT post the actual release to the work queue.
Also the entire __nf_tables_abort() function is wrapped in gc_seq
begin/end pair.
Therefore, async gc worker will never try to release the pending set
elements, as gc sequence is always stale.
It might be possible to speed up transaction aborts via work queue too,
this would result in a race and a possible use-after-free.
So fix this before it becomes an issue.
Fixes: 5f68718b34 ("netfilter: nf_tables: GC transaction API to avoid race with control plane")
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9b6614e5ea ]
eSR is activated when a chanctx is assigned to more than one link.
During eSR activation we should disable RLC for both phys, and configure
the FW with a special phy command for both phys.
Currently we assign the phy_ctxt to the link only after eSR activation,
so RLC is not disabled for the new phy_ctxt, and a cmd is not sent to FW.
Fix this by first assigning the new phy_ctxt to the link and then
doing the eSR activation.
Fixes: 12bacfc2c0 ("wifi: iwlwifi: handle eSR transitions")
Reviewed-by: Gregory Greenman <gregory.greenman@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20231219215605.3d94507f5d9a.I537fcd73aedf94c7348c03157e486f24301fef14@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit cb2dfacb19 ]
The driver copies the userspace buffer into an internal NUL
byte terminated buffer. While doing so, it was reading beyond
the end of the userspace buffer, overwriting its own NUL
termination in the process.
Fix this by only copying the correct number of bytes.
Fixes: 3f244876ef ("wifi: iwlwifi: make debugfs entries link specific")
Signed-off-by: Anjaneyulu <pagadala.yesu.anjaneyulu@intel.com>
Reviewed-by: Gregory Greenman <gregory.greenman@intel.com>
Reviewed-by: Benjamin Berg <benjamin.berg@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20231219215605.e4913deb2ad4.Idcf6a7e909ff4b7801cd49c2f691f84a2f68eff9@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c5bfdb4663 ]
It is possible that though multiple links are enabled we cannot enabled
EMLSR enable more than a single link, e.g., all valid links are on the
same band etc. Thus, do not warn in case no valid link pair is found.
Fixes: b9be67fb42 ("wifi: iwlwifi: mvm: Add basic link selection logic")
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Reviewed-by: Gregory Greenman <gregory.greenman@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20231219215605.142e57a05230.I7cfe78c94c3d15c4c744bccadd8f187e43594932@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2afc3dad39 ]
If we want to drop packets, that's surely a good thing to
do when we want to enter rfkill. Send this command despite
rfkill so we can successfully clean up everything, we need
to handle it separately since it has CMD_WANT_SKB, so it's
not going to automatically return success when in rfkill.
Fixes: d4e3a341b8 ("iwlwifi: mvm: add support for new flush queue response")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Reviewed-by: Gregory Greenman <gregory.greenman@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20231219215605.c528a6fa6cec.Ibe5e9560359ccc0fba60c35e01de285c376748a2@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b1a2e5c310 ]
The firmware changed their mind, don't set the chains to zero,
instead set them to 1 as we normally would for connections to
APs that don't use MIMO.
Fixes: 2a7ce54ccc ("iwlwifi: mvm: honour firmware SMPS requests")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Reviewed-by: Luciano Coelho <luciano.coelho@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20231219215605.7f031f1a127f.Idc816e0f604b07d22a9d5352bc23c445512fad14@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
