Fix the following error, which sometimes happens during the NFC data
transfer:
atmel_nand 80000000.nand: Time out to wait for interrupt: 0x00010000
atmel_nand 80000000.nand: something wrong, No XFR_DONE interrupt comes.
The root cause is that in the interrupt handler, we read the ISR but
only handle one interrupt. If more than one interrupt arrive at the same
time, then the second one will be lost.
During the NFC data transfer. Two NFC interrupts (NFC_CMD_DONE and
NFC_XFR_DONE) may come at the same time.
NFC_CMD_DONE means NFC command is sent, and NFC_XFR_DONE means NFC data
is transferred.
This patch can handle multiple NFC interrupts at the same time. During
the NFC data transfer, we need to wait for two NFC interrupts:
NFC_CMD_DONE and NFC_XFR_DONE.
Also we separate the completion initialization code to a
nfc_prepare_interrupt(), which is paired with nfc_wait_interrupt().
We call nfc_prepare_interrupt() before sending out nfc commands, to make
sure no interrupt lost.
Reported-by: Matthieu CRAPET <Matthieu.CRAPET@ingenico.com>
Tested-by: Matthieu Crapet <Matthieu.Crapet@ingenico.com>
Signed-off-by: Josh Wu <josh.wu@atmel.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
The original report from Nikhil was that if data_offset > 0 and bytesused == 0,
then the check in __verify_length() would fail, even though the spec says that
if bytes_used == 0, then it will be replaced by the actual length of the
buffer.
After digging into it a bit more I realized that there were several other
things wrong:
- in __verify_length() it would use the application-provided length value
for USERPTR and the vb2 core length for other memory models, but it
should have used the application-provided length as well for DMABUF.
- in __fill_vb2_buffer() on the other hand it would replace bytesused == 0
by the application-provided length, even for MMAP buffers where the
length is determined by the vb2 core.
- in __fill_vb2_buffer() it tries to figure out if all the planes have
bytesused == 0 before it will decide to replace bytesused by length.
However, the spec makes no such provision, and it makes for convoluted
code. So just replace any bytesused == 0 by the proper length.
The idea behind this was that you could use bytesused to signal empty
planes, something that is currently not supported. But that is better
done in the future by using one of the reserved fields in strucy v4l2_plane.
This patch fixes all these issues.
Regards,
Hans
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Reported-by: Nikhil Devshatwar <nikhil.nd@ti.com>
Cc: Nikhil Devshatwar <nikhil.nd@ti.com>
Acked-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
In nfc_device_ready(), it's more reasonable to check R/B bit in NFC_SR
than waiting for the R/B interrupt. It cost less time.
Signed-off-by: Josh Wu <josh.wu@atmel.com>
Tested-by: Matthieu Crapet <Matthieu.Crapet@ingenico.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Add a new function to read the NFC status. Meantime, this function will
check if there is any errors in NFC.
Signed-off-by: Josh Wu <josh.wu@atmel.com>
Tested-by: Matthieu Crapet <Matthieu.Crapet@ingenico.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
The link adjustment callback can be called as frequently as desired
by the PHY library, as such, let's avoid doing a Read/Modify/Write
sequence if nothing changed, since these register accesses can be
expensive.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If the ecc parameter is not the same as definition, when the
mtd core check these parameters, it will give the error result.
Take the following as an example:
Calculate how many bits can be corrected in one page.
According to the ecc parameters definition,
one page correct bits = (mtd->writesize * ecc->strength) / ecc->size
take the following use case as an example:
mtd->writesize = 2048 bytes
ecc->strength = 4 bytes (for 512 bytes)
before this patch, the ecc->size = 2048, so the result is 4 bytes.
after this patch, the ecc->size = 512, so the result is 16 bytes.
So, align the ecc parameters the same as definition to correct
this kind of error.
Signed-off-by: Bo Shen <voice.shen@atmel.com>
Acked-by: Josh Wu <josh.wu@atmel.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Add a converter to retrieve NAND timings from an ONFI NAND timing mode.
At the moment, only SDR NAND timings are supported.
Signed-off-by: Boris BREZILLON <boris.brezillon@free-electrons.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Fill FMT buffer size field in order to inform app which will be
used streaming buffer size. Currently driver doesn't allow buffer
size value proposed by application.
Cc: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
SDR API is very new and surprises may occur. Due to that print
notice to remind possible users.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
MSi3101 driver is moved out of staging and renamed.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Define a struct containing the standard NAND timings as described in NAND
datasheets.
Signed-off-by: Boris BREZILLON <boris.brezillon@free-electrons.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Move msi3101 out of staging and rename to msi2500.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Regular randconfig nightly testing has detected problems with omapdrm.
omapdrm fails to build when the kernel is built to support 64-bit DMA
addresses and/or 64-bit physical addresses due to an assumption about
the width of these types.
Use %pad to print DMA addresses, rather than %x or %Zx (which is even
more wrong than %x). Avoid passing a uint32_t pointer into a function
which expects dma_addr_t pointer.
drivers/gpu/drm/omapdrm/omap_plane.c: In function 'omap_plane_pre_apply':
drivers/gpu/drm/omapdrm/omap_plane.c:145:2: error: format '%x' expects argument of type 'unsigned int', but argument 5 has type 'dma_addr_t' [-Werror=format]
drivers/gpu/drm/omapdrm/omap_plane.c:145:2: error: format '%x' expects argument of type 'unsigned int', but argument 6 has type 'dma_addr_t' [-Werror=format]
make[5]: *** [drivers/gpu/drm/omapdrm/omap_plane.o] Error 1
drivers/gpu/drm/omapdrm/omap_gem.c: In function 'omap_gem_get_paddr':
drivers/gpu/drm/omapdrm/omap_gem.c:794:4: error: format '%x' expects argument of type 'unsigned int', but argument 3 has type 'dma_addr_t' [-Werror=format]
drivers/gpu/drm/omapdrm/omap_gem.c: In function 'omap_gem_describe':
drivers/gpu/drm/omapdrm/omap_gem.c:991:4: error: format '%Zx' expects argument of type 'size_t', but argument 7 has type 'dma_addr_t' [-Werror=format]
drivers/gpu/drm/omapdrm/omap_gem.c: In function 'omap_gem_init':
drivers/gpu/drm/omapdrm/omap_gem.c:1470:4: error: format '%x' expects argument of type 'unsigned int', but argument 7 has type 'dma_addr_t' [-Werror=format]
make[5]: *** [drivers/gpu/drm/omapdrm/omap_gem.o] Error 1
drivers/gpu/drm/omapdrm/omap_dmm_tiler.c: In function 'dmm_txn_append':
drivers/gpu/drm/omapdrm/omap_dmm_tiler.c:226:2: error: passing argument 3 of 'alloc_dma' from incompatible pointer type [-Werror]
make[5]: *** [drivers/gpu/drm/omapdrm/omap_dmm_tiler.o] Error 1
make[5]: Target `__build' not remade because of errors.
make[4]: *** [drivers/gpu/drm/omapdrm] Error 2
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Regular nightly randconfig build testing discovered these warnings:
drivers/gpu/drm/bochs/bochs_drv.c💯12: warning: 'bochs_pm_suspend' defined but not used [-Wunused-function]
drivers/gpu/drm/bochs/bochs_drv.c:117:12: warning: 'bochs_pm_resume' defined but not used [-Wunused-function]
Fix these by adding the same condition that SET_SYSTEM_SLEEP_PM_OPS()
uses.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Regular nightly randconfig build testing discovered these warnings:
drivers/gpu/drm/cirrus/cirrus_drv.c:79:12: warning: 'cirrus_pm_suspend' defined but not used [-Wunused-function]
drivers/gpu/drm/cirrus/cirrus_drv.c:96:12: warning: 'cirrus_pm_resume' defined but not used [-Wunused-function]
Fix these by adding the same condition that SET_SYSTEM_SLEEP_PM_OPS()
uses.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Dave Airlie <airlied@redhat.com>
drivers/gpu/drm/shmobile/shmob_drm_drv.c:300:5: warning: "CONFIG_PM_SLEEP" is not defined [-Wundef]
Always use #ifdef with CONFIG symbols, never just bare #if
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Dave Airlie <airlied@redhat.com>
drivers/gpu/drm/rcar-du/rcar_du_drv.c:190:5: warning: "CONFIG_PM_SLEEP" is not defined [-Wundef]
Always use #ifdef with CONFIG symbols, never just bare #if
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Dave Airlie <airlied@redhat.com>
In tda998x_encoder_destroy(), priv->cec is never NULL, so,
remove its test.
Signed-off-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Evil super powers maintainer abuse, get i915 mst support into -next.
* 'drm-i915-mst-support-next' of git://people.freedesktop.org/~airlied/linux:
drm/i915: mst topology dumper in debugfs (v0.2)
drm/i915: add DP 1.2 MST support (v0.7)
drm/i915: split conversion function out into separate function
drm/i915: check connector->encoder before using it.
i915: split some DP modesetting code into a separate function
drm/i915: add some registers need for displayport MST support.
use the mst helper code to dump the topology in debugfs.
v0.2: drop is_mst check - as we want to dump other info
Reviewed-by: Todd Previte <tprevite@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
This adds DP 1.2 MST support on Haswell systems.
Notes:
a) this reworks irq handling for DP MST ports, so that we can
avoid the mode config locking in the current hpd handlers, as
we need to process up/down msgs at a better time.
Changes since v0.1:
use PORT_PCH_HOTPLUG to detect short vs long pulses
add a workqueue to deal with digital events as they can get blocked on the
main workqueue beyong mode_config mutex
fix a bunch of modeset checker warnings
acks irqs in the driver
cleanup the MST encoders
Changes since v0.2:
check irq status again in work handler
move around bring up and tear down to fix DPMS on/off
use path properties.
Changes since v0.3:
updates for mst apis
more state checker fixes
irq handling improvements
fbcon handling support
improved reference counting of link - fixes redocking.
Changes since v0.4:
handle gpu reset hpd reinit without oopsing
check link status on HPD irqs
fix suspend/resume
Changes since v0.5:
use proper functions to get max link/lane counts
fix another checker backtrace - due to connectors disappearing.
set output type in more places fro, unknown->displayport
don't talk to devices if no HPD asserted
check mst on short irqs only
check link status properly
rebase onto prepping irq changes.
drop unsued force_act
Changes since v0.6:
cleanup unused struct entry.
[airlied: fix some sparse warnings].
Reviewed-by: Todd Previte <tprevite@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
sparse complains about these functions missing a prototype, but looking
closer they aren't (and likely not supposed to be) used outside of this
source file, so they can be made static.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
The final parameter to ttm_bo_reserve() is a pointer, therefore callers
should use NULL instead of 0.
Fixes a bunch of sparse warnings of this type:
warning: Using plain integer as NULL pointer
Signed-off-by: Thierry Reding <treding@nvidia.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
The drm_copy_field() function copies strings into userspace buffers, so
the first parameter needs to have a __user annotation to avoid warnings
from the sparse checker.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Reviewed-by: David Herrmann <dh.herrmann@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
* 'drm-fixes-3.16' of git://people.freedesktop.org/~agd5f/linux:
drm/radeon/TN: only enable bapm on MSI systems
drm/radeon: fix VM IB handling
drm/radeon: fix handling of radeon_vm_bo_rmv v3
drm/radeon: let's use GB for vm_size (v2)
Fill FMT buffer size field in order to inform app which will be
used streaming buffer size. Currently driver doesn't allow buffer
size value proposed by application.
Cc: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
New field buffersize was added to inform application maximum
buffer size used. Add it to documentation too.
Cc: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Fill FMT buffer size field in order to inform app which will be
used streaming buffer size. Currently driver doesn't allow buffer
size value proposed by application.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Add buffer size field to struct v4l2_sdr_format. It is used for
negotiate streaming buffer size between application and driver.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
This is needed for PCTV 522e support.
Signed-off-by: Matthias Schwarzott <zzam@gentoo.org>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
This is needed for PCTV 522e support.
Signed-off-by: Matthias Schwarzott <zzam@gentoo.org>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Modify all users of si2157_config to correctly initialize all not
listed values to 0.
Signed-off-by: Matthias Schwarzott <zzam@gentoo.org>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Modify all users of si2157_config to correctly initialize all not
listed values to 0.
Signed-off-by: Matthias Schwarzott <zzam@gentoo.org>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The struct prototype is defined at the beginning of the code as
"si2157_ops" but the real struct is called "si2157_tuner_ops".
This is causing the name to be empty on this info msg: si2157 16-0060:
si2157: found a '' in cold state
[crope@iki.fi: commit msg from Luis email reply]
Signed-off-by: Olli Salonen <olli.salonen@iki.fi>
Cc: Luis Alves <ljalvs@gmail.com>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Testing demod presence on probe fails if the demod was sleep mode.
Signed-off-by: Luis Alves <ljalvs@gmail.com>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
In case of failure the return value was always 0. Return proper
error code (ENODEV) instead.
Signed-off-by: Luis Alves <ljalvs@gmail.com>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Improve scanning performance by setting property 0301 with a value
from Windows driver.
Signed-off-by: Olli Salonen <olli.salonen@iki.fi>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
This patch adds symbol rate setting to the driver.
Signed-off-by: Luis Alves <ljalvs@gmail.com>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Print notice on driver load: "SDR API is still slightly
experimental and functionality changes may follow". It is just
remind possible used SDR API is very new and surprises may occur.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Move it out of staging into media like all the other SDR drivers
too. There is no good reasons to keep these SDR drivers in staging.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
v4l2-compliance is now happy with frequency ranges where both lower
and upper limit is same.
Cc: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
