snd_soc_dai_driver has .ops for call back functions (A), but it also
has other call back functions (B). It is duplicated and confusable.
struct snd_soc_dai_driver {
...
^ int (*probe)(...);
| int (*remove)(...);
(B) int (*compress_new)(...);
| int (*pcm_new)(...);
v ...
(A) const struct snd_soc_dai_ops *ops;
...
}
This patch merges (B) into (A).
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Link: https://lore.kernel.org/r/87v8dpb0w6.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>
This is the module init function, which by definition is used only
locally, so mark it static to avoid a warning:
drivers/macintosh/ams/ams-core.c:179:12: error: no previous prototype for 'ams_init' [-Werror=missing-prototypes]
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://msgid.link/20230810141947.1236730-7-arnd@kernel.org
Don't use kernel-doc "/**" comment format for non-kernel-doc comments.
This prevents a kernel-doc warning:
arch/powerpc/platforms/pseries/plpks.c:186: warning: This comment starts with '/**', but isn't a kernel-doc comment. Refer Documentation/doc-guide/kernel-doc.rst
* Label is combination of label attributes + name.
Fixes: 2454a7af0f ("powerpc/pseries: define driver for Platform KeyStore")
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Reported-by: kernel test robot <lkp@intel.com>
Link: lore.kernel.org/r/202308040430.GxmPAnwZ-lkp@intel.com
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://msgid.link/20230810000740.23756-1-rdunlap@infradead.org
With skiboot_defconfig, Clang reports:
CC arch/powerpc/mm/book3s64/radix_tlb.o
arch/powerpc/mm/book3s64/radix_tlb.c:419:20: error: unused function '_tlbie_pid_lpid' [-Werror,-Wunused-function]
static inline void _tlbie_pid_lpid(unsigned long pid, unsigned long lpid,
^
arch/powerpc/mm/book3s64/radix_tlb.c:663:20: error: unused function '_tlbie_va_range_lpid' [-Werror,-Wunused-function]
static inline void _tlbie_va_range_lpid(unsigned long start, unsigned long end,
^
This is because those functions are only called from functions
enclosed in a #ifdef CONFIG_KVM_BOOK3S_HV_POSSIBLE
Move below functions inside that #ifdef
* __tlbie_pid_lpid(unsigned long pid,
* __tlbie_va_lpid(unsigned long va, unsigned long pid,
* fixup_tlbie_pid_lpid(unsigned long pid, unsigned long lpid)
* _tlbie_pid_lpid(unsigned long pid, unsigned long lpid,
* fixup_tlbie_va_range_lpid(unsigned long va,
* __tlbie_va_range_lpid(unsigned long start, unsigned long end,
* _tlbie_va_range_lpid(unsigned long start, unsigned long end,
Fixes: f0c6fbbb90 ("KVM: PPC: Book3S HV: Add support for H_RPT_INVALIDATE")
Reported-by: kernel test robot <lkp@intel.com>
Closes: https://lore.kernel.org/oe-kbuild-all/202307260802.Mjr99P5O-lkp@intel.com/
Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://msgid.link/3d72efd39f986ee939d068af69fdce28bd600766.1691568093.git.christophe.leroy@csgroup.eu
Randconfig testing with W=1 showed up these warnings that I'd like to enable
by default:
arch/powerpc/xmon/xmon.c: In function 'dump_tlb_book3e':
arch/powerpc/xmon/xmon.c:3833:42: error: variable 'lrat' set but not used [-Werror=unused-but-set-variable]
3833 | int i, tlb, ntlbs, pidsz, lpidsz, rasz, lrat = 0;
| ^~~~
arch/powerpc/xmon/xmon.c:3831:23: error: variable 'lpidmask' set but not used [-Werror=unused-but-set-variable]
3831 | u32 mmucfg, pidmask, lpidmask;
| ^~~~~~~~
arch/powerpc/xmon/xmon.c:3831:14: error: variable 'pidmask' set but not used [-Werror=unused-but-set-variable]
3831 | u32 mmucfg, pidmask, lpidmask;
| ^~~~~~~
Just remove these as they have been unused since the code was added in 2010.
Fixes: 03247157f7 ("powerpc/book3e: Add TLB dump in xmon for Book3E")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://msgid.link/20230809131024.2039647-2-arnd@kernel.org
A while ago I created a2305e3de8 ("powerpc: mark local variables
around longjmp as volatile") in order to allow building powerpc with
-Wextra enabled on gcc-11.
I tried this again with gcc-13 and found two more of the same issues,
presumably based on slightly different optimization paths being taken
here:
arch/powerpc/xmon/xmon.c:3306:27: error: variable 'mm' might be clobbered by 'longjmp' or 'vfork' [-Werror=clobbered]
arch/powerpc/kexec/crash.c:353:22: error: variable 'i' might be clobbered by 'longjmp' or 'vfork' [-Werror=clobbered]
I checked a bunch of randconfigs and found only these two, so just
address them the same way as the others.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://msgid.link/20230809131024.2039647-1-arnd@kernel.org
Serial is a critical feature for logging and debuging, and the other
architectures enable serial by default.
Let's enable CONFIG_SERIAL_PMACZILOG and CONFIG_SERIAL_PMACZILOG_CONSOLE
by default.
Signed-off-by: Yuan Tan <tanyuan@tinylab.org>
Reviewed-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://msgid.link/bb7b5f9958b3e3a20f6573ff7ce7c5dc566e7e32.1690982937.git.tanyuan@tinylab.org
Move the kernel-doc comments for locomo_probe() to immediately before
that function instead of before __locomo_probe() to prevent
kernel-doc warnings. Adjust the documented function parameters and
make the return values compatible with ReST by adding bullets to them.
Add more possible return values to the list.
Prevents these warnings:
arch/arm/common/locomo.c:368: warning: Function parameter or member 'me' not described in '__locomo_probe'
arch/arm/common/locomo.c:368: warning: Function parameter or member 'mem' not described in '__locomo_probe'
arch/arm/common/locomo.c:368: warning: Function parameter or member 'irq' not described in '__locomo_probe'
arch/arm/common/locomo.c:368: warning: expecting prototype for locomo_probe(). Prototype was for __locomo_probe() instead
Link: lore.kernel.org/r/202308050851.zAvHe6y7-lkp@intel.com
Fixes: 5eb6e28043 ("ARM: 9289/1: Allow pre-ARMv5 builds with ld.lld 16.0.0 and newer")
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Reported-by: kernel test robot <lkp@intel.com>
Cc: Nick Desaulniers <ndesaulniers@google.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Nathan Chancellor <nathan@kernel.org>
Cc: linux-arm-kernel@lists.infradead.org
Cc: patches@armlinux.org.uk
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
If a panic is triggered by a hrtimer interrupt all online cpus will be
notified and set offline. But as highlighted by commit 19dbdcb803
("smp: Warn on function calls from softirq context") this call should
not be made synchronous with disabled interrupts:
softdog: Initiating panic
Kernel panic - not syncing: Software Watchdog Timer expired
WARNING: CPU: 1 PID: 0 at kernel/smp.c:753 smp_call_function_many_cond
unwind_backtrace:
show_stack
dump_stack_lvl
__warn
warn_slowpath_fmt
smp_call_function_many_cond
smp_call_function
crash_smp_send_stop.part.0
machine_crash_shutdown
__crash_kexec
panic
softdog_fire
__hrtimer_run_queues
hrtimer_interrupt
Make the smp call for machine_crash_nonpanic_core() asynchronous.
Signed-off-by: Mårten Lindahl <marten.lindahl@axis.com>
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Arm platforms use is_default_overflow_handler() to determine if the
hw_breakpoint code should single-step over the breakpoint trigger or
let the custom handler deal with it.
Since bpf_overflow_handler() currently isn't recognized as a default
handler, attaching a BPF program to a PERF_TYPE_BREAKPOINT event causes
it to keep firing (the instruction triggering the data abort exception
is never skipped). For example:
# bpftrace -e 'watchpoint:0x10000:4:w { print("hit") }' -c ./test
Attaching 1 probe...
hit
hit
[...]
^C
(./test performs a single 4-byte store to 0x10000)
This patch replaces the check with uses_default_overflow_handler(),
which accounts for the bpf_overflow_handler() case by also testing
if one of the perf_event_output functions gets invoked indirectly,
via orig_default_handler.
Link: https://lore.kernel.org/linux-arm-kernel/20220923203644.2731604-1-tnovak@fb.com/
Signed-off-by: Tomislav Novak <tnovak@fb.com>
Tested-by: Samuel Gosselin <sgosselin@google.com> # arm64
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
If an output buffer size exceeded U16_MAX, the min_t(u16, ...) cast in
copy_data() was causing writes to truncate. This manifested as output
bytes being skipped, seen as %NUL bytes in pstore dumps when the available
record size was larger than 65536. Fix the cast to no longer truncate
the calculation.
Cc: Petr Mladek <pmladek@suse.com>
Cc: Sergey Senozhatsky <senozhatsky@chromium.org>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: John Ogness <john.ogness@linutronix.de>
Reported-by: Vijay Balakrishna <vijayb@linux.microsoft.com>
Link: https://lore.kernel.org/lkml/d8bb1ec7-a4c5-43a2-9de0-9643a70b899f@linux.microsoft.com/
Fixes: b6cf8b3f33 ("printk: add lockless ringbuffer")
Cc: stable@vger.kernel.org
Signed-off-by: Kees Cook <keescook@chromium.org>
Tested-by: Vijay Balakrishna <vijayb@linux.microsoft.com>
Tested-by: Guilherme G. Piccoli <gpiccoli@igalia.com> # Steam Deck
Reviewed-by: Tyler Hicks (Microsoft) <code@tyhicks.com>
Tested-by: Tyler Hicks (Microsoft) <code@tyhicks.com>
Reviewed-by: John Ogness <john.ogness@linutronix.de>
Reviewed-by: Sergey Senozhatsky <senozhatsky@chromium.org>
Reviewed-by: Petr Mladek <pmladek@suse.com>
Signed-off-by: Petr Mladek <pmladek@suse.com>
Link: https://lore.kernel.org/r/20230811054528.never.165-kees@kernel.org
These formats are used by Android so having them available
allows the DU to be used for composition operations.
Signed-off-by: Damian Hobson-Garcia <dhobsong@igel.co.jp>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Add additional pixel formats for which blending is disabled when
DRM_MODE_BLEND_PIXEL_NONE is set.
Refactor the fourcc selection into a separate function to handle the
increased number of formats.
Signed-off-by: Damian Hobson-Garcia <dhobsong@igel.co.jp>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
The (large) rcar_du_modeset_init() function can fail for many reasons,
two of two involving probe deferral. Use dev_err_probe() in those code
paths to record the cause of the probe deferral, in order to help
debugging probe issues.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
drm_info() adds proper context to the kernel log message, as it receives
the drm_device pointer. It is thus preferred over DRM_INFO(). Replace
the latter with the former.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
The on-board eeprom on beaglebone series has a power supply from
VDD_3V3A, add that to dts to reduce dummy regulator warning.
Signed-off-by: Shengyu Qu <wiagn233@outlook.com>
Message-ID: <TY3P286MB2611CDC84604B11570B4A8D2980FA@TY3P286MB2611.JPNP286.PROD.OUTLOOK.COM>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch adds ethernet PHY reset GPIO config for Beaglebone Black
series boards with revision C3. This fixes a random phy startup failure
bug discussed at [1]. The GPIO pin used for reset is not used on older
revisions, so it is ok to apply to all board revisions. The reset timing
was discussed and tested at [2].
[1] https://forum.digikey.com/t/ethernet-device-is-not-detecting-on-ubuntu-20-04-lts-on-bbg/19948
[2] https://forum.beagleboard.org/t/recognizing-a-beaglebone-black-rev-c3-board/31249/
Signed-off-by: Robert Nelson <robertcnelson@gmail.com>
Signed-off-by: Shengyu Qu <wiagn233@outlook.com>
Message-ID: <TY3P286MB26113797A3B2EC7E0348BBB2980FA@TY3P286MB2611.JPNP286.PROD.OUTLOOK.COM>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This test verifies whether the encapsulated packets have the correct
configured TTL. It does so by sending ICMP packets through the test
topology and mirroring them to a gretap netdevice. On a busy host
however, more than just the test ICMP packets may end up flowing
through the topology, get mirrored, and counted. This leads to
potential spurious failures as the test observes much more mirrored
packets than the sent test packets, and assumes a bug.
Fix this by tightening up the mirror action match. Change it from
matchall to a flower classifier matching on ICMP packets specifically.
Fixes: 45315673e0 ("selftests: forwarding: Test changes in mirror-to-gretap")
Signed-off-by: Petr Machata <petrm@nvidia.com>
Tested-by: Mirsad Todorovac <mirsad.todorovac@alu.unizg.hr>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since commit b09c68dc57 ("clk: imx: pll14xx: Support dynamic rates"),
the driver has the ability to dynamically compute PLL parameters to
approximate the requested rates. This is not always used, because the
logic is as follows:
- Check if the target rate is hardcoded in the frequency table
- Check if varying only kdiv is possible, so switch over is glitch free
- Compute rate dynamically by iterating over pdiv range
If we skip the frequency table for the 1443x PLL, we find that the
computed values differ to the hardcoded ones. This can be valid if the
hardcoded values guarantee for example an earlier lock-in or if the
divisors are chosen, so that other important rates are more likely to
be reached glitch-free.
For rates (393216000 and 361267200, this doesn't seem to be the case:
They are only approximated by existing parameters (393215995 and
361267196 Hz, respectively) and they aren't reachable glitch-free from
other hardcoded frequencies. Dropping them from the table allows us
to lock-in to these frequencies exactly.
This is immediately noticeable because they are the assigned-clock-rates
for IMX8MN_AUDIO_PLL1 and IMX8MN_AUDIO_PLL2, respectively and a look
into clk_summary so far showed that they were a few Hz short of the target:
imx8mn-board:~# grep audio_pll[12]_out /sys/kernel/debug/clk/clk_summary
audio_pll2_out 0 0 0 361267196 0 0 50000 N
audio_pll1_out 1 1 0 393215995 0 0 50000 Y
and afterwards:
imx8mn-board:~# grep audio_pll[12]_out /sys/kernel/debug/clk/clk_summary
audio_pll2_out 0 0 0 361267200 0 0 50000 N
audio_pll1_out 1 1 0 393216000 0 0 50000 Y
This change is equivalent to adding following hardcoded values:
/* rate mdiv pdiv sdiv kdiv */
PLL_1443X_RATE(393216000, 655, 5, 3, 23593),
PLL_1443X_RATE(361267200, 497, 33, 0, -16882),
Fixes: 053a4ffe29 ("clk: imx: imx8mm: fix audio pll setting")
Cc: stable@vger.kernel.org # v5.18+
Signed-off-by: Ahmad Fatoum <a.fatoum@pengutronix.de>
Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Link: https://lore.kernel.org/r/20230807084744.1184791-2-m.felsch@pengutronix.de
Signed-off-by: Abel Vesa <abel.vesa@linaro.org>
The PLL14xx hardware can be found on i.MX8M{M,N,P} SoCs and always come
with a 6-bit pre-divider. Neither the reference manuals nor the
datasheets of these SoCs do mention any restrictions. Furthermore the
current code doesn't respect the restrictions from the comment too.
Therefore drop the restriction and align the max pre-divider (pdiv)
value to 63 to get more accurate frequencies.
Fixes: b09c68dc57 ("clk: imx: pll14xx: Support dynamic rates")
Cc: stable@vger.kernel.org
Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Reviewed-by: Abel Vesa <abel.vesa@linaro.org>
Reviewed-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Tested-by: Ahmad Fatoum <a.fatoum@pengutronix.de>
Link: https://lore.kernel.org/r/20230807084744.1184791-1-m.felsch@pengutronix.de
Signed-off-by: Abel Vesa <abel.vesa@linaro.org>
Reconfiguring the clock divider to the exact same value is observed
on an i.MX8MN to often cause a longer than usual clock pause, probably
because the divider restarts counting whenever the register is rewritten.
This issue doesn't show up normally, because the clock framework will
take care to not call set_rate when the clock rate is the same.
However, when we reconfigure an upstream clock, the common code will
call set_rate with the newly calculated rate on all children, e.g.:
- sai5 is running normally and divides Audio PLL out by 16.
- Audio PLL rate is increased by 32Hz (glitch-free kdiv change)
- rates for children are recalculated and rates are set recursively
- imx8m_clk_composite_divider_set_rate(sai5) is called with
32/16 = 2Hz more
- imx8m_clk_composite_divider_set_rate computes same divider as before
- divider register is written, so it restarts counting from zero and
MCLK is briefly paused, so instead of e.g. 40ns, MCLK is low for 120ns.
Some external clock consumers can be upset by such unexpected clock pauses,
so let's make sure we only rewrite the divider value when the value to be
written is actually different.
Fixes: d3ff972813 ("clk: imx: Add imx composite clock")
Signed-off-by: Ahmad Fatoum <a.fatoum@pengutronix.de>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Link: https://lore.kernel.org/r/20230807082201.2332746-1-a.fatoum@pengutronix.de
Signed-off-by: Abel Vesa <abel.vesa@linaro.org>
The kprobes optimization check can_optimize() calls
insn_is_indirect_jump() to detect indirect jump instructions in
a target function. If any is found, creating an optprobe is disallowed
in the function because the jump could be from a jump table and could
potentially land in the middle of the target optprobe.
With retpolines, insn_is_indirect_jump() additionally looks for calls to
indirect thunks which the compiler potentially used to replace original
jumps. This extra check is however unnecessary because jump tables are
disabled when the kernel is built with retpolines. The same is currently
the case with IBT.
Based on this observation, remove the logic to look for calls to
indirect thunks and skip the check for indirect jumps altogether if the
kernel is built with retpolines or IBT. Remove subsequently the symbols
__indirect_thunk_start and __indirect_thunk_end which are no longer
needed.
Dropping this logic indirectly fixes a problem where the range
[__indirect_thunk_start, __indirect_thunk_end] wrongly included also the
return thunk. It caused that machines which used the return thunk as
a mitigation and didn't have it patched by any alternative ended up not
being able to use optprobes in any regular function.
Fixes: 0b53c374b9 ("x86/retpoline: Use -mfunction-return")
Suggested-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Suggested-by: Masami Hiramatsu (Google) <mhiramat@kernel.org>
Signed-off-by: Petr Pavlu <petr.pavlu@suse.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Signed-off-by: Borislav Petkov (AMD) <bp@alien8.de>
Acked-by: Masami Hiramatsu (Google) <mhiramat@kernel.org>
Link: https://lore.kernel.org/r/20230711091952.27944-3-petr.pavlu@suse.com
Add Logitech MX Anywhere 3 connected over Bluetooth to the device table
to get hidpi scroll supported. USB connection over the Unifying receiver
is already supported by the wildcard entry LDJ_DEVICE(HID_ANY_ID).
Signed-off-by: Maxim Mikityanskiy <maxtram95@gmail.com>
Reviewed-by: Bastien Nocera <hadess@hadess.net>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The linker script arch/x86/kernel/vmlinux.lds.S matches the thunk
sections ".text.__x86.*" from arch/x86/lib/retpoline.S as follows:
.text {
[...]
TEXT_TEXT
[...]
__indirect_thunk_start = .;
*(.text.__x86.*)
__indirect_thunk_end = .;
[...]
}
Macro TEXT_TEXT references TEXT_MAIN which normally expands to only
".text". However, with CONFIG_LTO_CLANG, TEXT_MAIN becomes
".text .text.[0-9a-zA-Z_]*" which wrongly matches also the thunk
sections. The output layout is then different than expected. For
instance, the currently defined range [__indirect_thunk_start,
__indirect_thunk_end] becomes empty.
Prevent the problem by using ".." as the first separator, for example,
".text..__x86.indirect_thunk". This pattern is utilized by other
explicit section names which start with one of the standard prefixes,
such as ".text" or ".data", and that need to be individually selected in
the linker script.
[ nathan: Fix conflicts with SRSO and fold in fix issue brought up by
Andrew Cooper in post-review:
https://lore.kernel.org/20230803230323.1478869-1-andrew.cooper3@citrix.com ]
Fixes: dc5723b02e ("kbuild: add support for Clang LTO")
Signed-off-by: Petr Pavlu <petr.pavlu@suse.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Signed-off-by: Nathan Chancellor <nathan@kernel.org>
Signed-off-by: Borislav Petkov (AMD) <bp@alien8.de>
Link: https://lore.kernel.org/r/20230711091952.27944-2-petr.pavlu@suse.com
Help differentiate the two remote related "serial" struct variables by
renaming "wacom_remote_data" to "wacom_remote_work_data".
Signed-off-by: Aaron Skomra <skomra@gmail.com>
Signed-off-by: Aaron Armstrong Skomra <aaron.skomra@wacom.com>
Reviewed-by: Jason Gerecke <jason.gerecke@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The 'connected' variable was poorly named, and this has led to some
confusion. We can get the same information by checking if a serial number
exists in the specified EKR slot.
Signed-off-by: Aaron Skomra <skomra@gmail.com>
Signed-off-by: Aaron Armstrong Skomra <aaron.skomra@wacom.com>
Reviewed-by: Jason Gerecke <jason.gerecke@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Currently the EKR battery remains even after we stop getting information
from the device. This can lead to a stale battery persisting indefinitely
in userspace.
The remote sends a heartbeat every 10 seconds. Delete the battery if we
miss two heartbeats (after 21 seconds). Restore the battery once we see
a heartbeat again.
Signed-off-by: Aaron Skomra <skomra@gmail.com>
Signed-off-by: Aaron Armstrong Skomra <aaron.skomra@wacom.com>
Reviewed-by: Jason Gerecke <jason.gerecke@wacom.com>
Fixes: 9f1015d45f ("HID: wacom: EKR: attach the power_supply on first connection")
CC: stable@vger.kernel.org
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Previously would let led_classdev handle renaming when name collision
occurred. Now that an ID allocator is used to uniquely identify multiple
Thunderstrike controllers, generate unique led device names.
Signed-off-by: Rahul Rameshbabu <rrameshbabu@nvidia.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Use power supply API to expose battery information about connected
Thunderstrike controllers to the system. Provide information on battery
capacity, charge status, charger type, voltage, and temperature.
Signed-off-by: Rahul Rameshbabu <rrameshbabu@nvidia.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Avoid calling thunderstrike_led_set_brightness from thunderstrike_create
when led_classdev_unregister is called. led_classdev_unregister was called
from thunderstrike_create in the error path. Calling
thunderstrike_led_set_brightness in this situation is unsafe.
Fixes: f88af60e74 ("HID: nvidia-shield: Support LED functionality for Thunderstrike")
Signed-off-by: Rahul Rameshbabu <rrameshbabu@nvidia.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The __mx25_clocks_init function always returns 0 and its only
caller does not check the return value. Let's remove it.
Signed-off-by: Martin Kaiser <martin@kaiser.cx>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Stephen Boyd <sboyd@kernel.org>
Link: https://lore.kernel.org/r/20230802184046.153394-3-martin@kaiser.cx
Signed-off-by: Abel Vesa <abel.vesa@linaro.org>
Print the imx25 silicon revision when the clocks are initialised.
Use the same mechanism as for imx27, i.e. call mx25_revision.
This function is unused at the moment.
Signed-off-by: Martin Kaiser <martin@kaiser.cx>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Stephen Boyd <sboyd@kernel.org>
Link: https://lore.kernel.org/r/20230802184046.153394-2-martin@kaiser.cx
Signed-off-by: Abel Vesa <abel.vesa@linaro.org>
Add a hid-google-stadiaff module to support rumble based force feedback
on the Google Stadia controller. This works using the HID output
endpoint exposed on both the USB and BLE interface.
Signed-off-by: Fabio Baltieri <fabiobaltieri@chromium.org>
Reviewed-by: Rahul Rameshbabu <rrameshbabu@nvidia.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The lightspeed receiver for the Pro X Superlight uses 13 byte mouse reports
without a report id. The workaround for such cases has been adjusted to
handle these larger packets.
The device now reports the status of its battery in wireless mode and
libratbag now recognizes the device and it can be configured with Piper.
https://github.com/libratbag/libratbag/pull/1122
Co-developed-by: Filipe Laíns <lains@riseup.net>
Signed-off-by: Filipe Laíns <lains@riseup.net>
Signed-off-by: Mavroudis Chatzilazaridis <mavchatz@protonmail.com>
Reviewed-by: Bastien Nocera <hadess@hadess.net>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
This patch adds support for the Pro X Superlight over wired USB.
The device now reports the status of its battery.
Co-developed-by: Filipe Laíns <lains@riseup.net>
Signed-off-by: Filipe Laíns <lains@riseup.net>
Signed-off-by: Mavroudis Chatzilazaridis <mavchatz@protonmail.com>
Reviewed-by: Bastien Nocera <hadess@hadess.net>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The hardware don't have a SAI4 instance so remove the define. Use a
comment to keep it as reference and to avoid confusion.
Fixes: 1088691447 ("dt-bindings: imx: Add clock binding doc for i.MX8MP")
Acked-by: Stephen Boyd <sboyd@kernel.org>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Link: https://lore.kernel.org/r/20230731142150.3186650-2-m.felsch@pengutronix.de
Signed-off-by: Abel Vesa <abel.vesa@linaro.org>
The reference manual don't mention a SAI4 hardware block. This would be
clock slice 78 which is skipped (TRM, page 237). Remove any reference to
this clock to align the driver with the reality.
Fixes: 9c140d9926 ("clk: imx: Add support for i.MX8MP clock driver")
Acked-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Link: https://lore.kernel.org/r/20230731142150.3186650-1-m.felsch@pengutronix.de
Signed-off-by: Abel Vesa <abel.vesa@linaro.org>
The SPLL2 on iMX8ULP is different with other frac PLLs, it can
support VCO from 650Mhz to 1Ghz. Following the changes to pllv4,
use the new type IMX_PLLV4_IMX8ULP_1GHZ.
Fixes: c43a801a57 ("clk: imx: Add clock driver for imx8ulp")
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Abel Vesa <abel.vesa@linaro.org>
Link: https://lore.kernel.org/r/20230625123340.4067536-2-peng.fan@oss.nxp.com
Signed-off-by: Abel Vesa <abel.vesa@linaro.org>
The SPLL2 on iMX8ULP is different with other frac PLLs, it can
support VCO from 650Mhz to 1Ghz. According to RM, the MULT is
using a range from 27 to 54, not some fixed values. If using
current PLL implementation, some clock rate can't be supported.
Fix the issue by adding new type for the SPLL2 and use MULT range
to replace MULT table
Fixes: 5f0601c47c ("clk: imx: Update the pllv4 to support imx8ulp")
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Jacky Bai <ping.bai@nxp.com>
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Abel Vesa <abel.vesa@linaro.org>
Link: https://lore.kernel.org/r/20230625123340.4067536-1-peng.fan@oss.nxp.com
Signed-off-by: Abel Vesa <abel.vesa@linaro.org>
Skip the srso cmd line parsing which is not needed on Zen1/2 with SMT
disabled and with the proper microcode applied (latter should be the
case anyway) as those are not affected.
Fixes: 5a15d83488 ("x86/srso: Tie SBPB bit setting to microcode patch detection")
Signed-off-by: Borislav Petkov (AMD) <bp@alien8.de>
Link: https://lore.kernel.org/r/20230813104517.3346-1-bp@alien8.de
The Audio Clock Mux (ACM) is a collection of control registers
and multiplexers that are used to route the audio source clocks
to the audio peripherals.
Each audio peripheral has its dedicated audio clock mux
(which differ based on usage) and control register.
Signed-off-by: Shengjiu Wang <shengjiu.wang@nxp.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Abel Vesa <abel.vesa@linaro.org>
Link: https://lore.kernel.org/r/1690260984-25744-3-git-send-email-shengjiu.wang@nxp.com
Signed-off-by: Abel Vesa <abel.vesa@linaro.org>
Add the clock dt-binding file for Audio Clock Mux. which
is the IP for i.MX8QM, i.MX8QXP, i.MX8DXL.
Add the clockid for clocks in header file.
The Audio Clock Mux is binded with all the audio IP and audio clocks
in the subsystem, so need to list the power domain of related clocks
and IPs. Each clock and IP has a power domain, so there are so many
power domains.
Signed-off-by: Shengjiu Wang <shengjiu.wang@nxp.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/1690260984-25744-2-git-send-email-shengjiu.wang@nxp.com
Signed-off-by: Abel Vesa <abel.vesa@linaro.org>
Add support for the Steelseries Arctis 1 XBox headset. This driver
will export the battery information from the headset, as well as the
"wireless_status" property.
Signed-off-by: Bastien Nocera <hadess@hadess.net>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
When connecting the Trackpad 1 via any bluetooth adapter, the device
disconnects whenever the battery level is queried. It reconnects
again after a few seconds, but it's an incredibly jarring experience
since it will just cut out in the middle of mouse operations.
This patch ignores querying the battery and avoids disconnects.
This bug is reported here:
- https://bugzilla.kernel.org/show_bug.cgi?id=204589
- https://bugs.launchpad.net/ubuntu/+source/linux/+bug/1834085
It looks like a similar approach (disabling battery checking)
was also suggested for the Apple Magic Mouse before a custom
driver was created:
https://bugzilla.kernel.org/show_bug.cgi?id=103631
Signed-off-by: Nimish Gåtam <nimishg@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>