[ Upstream commit a9f96dc59b ]
of_find_net_device_by_node() searches net devices by their /sys/class/net/,
entry. It is documented in its kernel-doc that:
* If successful, returns a pointer to the net_device with the embedded
* struct device refcount incremented by one, or NULL on failure. The
* refcount must be dropped when done with the net_device.
We are missing a put_device(&conduit->dev) which we could place at the
end of dsa_tree_find_first_conduit(). But to explain why calling
put_device() right away is safe is the same as to explain why the chosen
solution is different.
The code is very poorly split: dsa_tree_find_first_conduit() was first
introduced in commit 95f510d0b7 ("net: dsa: allow the DSA master to be
seen and changed through rtnetlink") but was first used several commits
later, in commit acc43b7bf5 ("net: dsa: allow masters to join a LAG").
Assume there is a switch with 2 CPU ports and 2 conduits, eno2 and eno3.
When we create a LAG (bonding or team device) and place eno2 and eno3
beneath it, we create a 3rd conduit (the LAG device itself), but this is
slightly different than the first two.
Namely, the cpu_dp->conduit pointer of the CPU ports does not change,
and remains pointing towards the physical Ethernet controllers which are
now LAG ports. Only 2 things change:
- the LAG device has a dev->dsa_ptr which marks it as a DSA conduit
- dsa_port_to_conduit(user port) finds the LAG and not the physical
conduit, because of the dp->cpu_port_in_lag bit being set.
When the LAG device is destroyed, dsa_tree_migrate_ports_from_lag_conduit()
is called and this is where dsa_tree_find_first_conduit() kicks in.
This is the logical mistake and the reason why introducing code in one
patch and using it from another is bad practice. I didn't realize that I
don't have to call of_find_net_device_by_node() again; the cpu_dp->conduit
association was never undone, and is still available for direct (re)use.
There's only one concern - maybe the conduit disappeared in the
meantime, but the netdev_hold() call we made during dsa_port_parse_cpu()
(see previous change) ensures that this was not the case.
Therefore, fixing the code means reimplementing it in the simplest way.
I am blaming the time of use, since this is what "git blame" would show
if we were to monitor for the conduit's kobject's refcount remaining
elevated instead of being freed.
Tested on the NXP LS1028A, using the steps from
Documentation/networking/dsa/configuration.rst section "Affinity of user
ports to CPU ports", followed by (extra prints added by me):
$ ip link del bond0
mscc_felix 0000:00:00.5 swp3: Link is Down
bond0 (unregistering): (slave eno2): Releasing backup interface
fsl_enetc 0000:00:00.2 eno2: Link is Down
mscc_felix 0000:00:00.5 swp0: bond0 disappeared, migrating to eno2
mscc_felix 0000:00:00.5 swp1: bond0 disappeared, migrating to eno2
mscc_felix 0000:00:00.5 swp2: bond0 disappeared, migrating to eno2
mscc_felix 0000:00:00.5 swp3: bond0 disappeared, migrating to eno2
Fixes: acc43b7bf5 ("net: dsa: allow masters to join a LAG")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Link: https://patch.msgid.link/20251215150236.3931670-2-vladimir.oltean@nxp.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 06e219f6a7 ]
Problem description
-------------------
DSA has a mumbo-jumbo of reference handling of the conduit net device
and its kobject which, sadly, is just wrong and doesn't make sense.
There are two distinct problems.
1. The OF path, which uses of_find_net_device_by_node(), never releases
the elevated refcount on the conduit's kobject. Nominally, the OF and
non-OF paths should result in objects having identical reference
counts taken, and it is already suspicious that
dsa_dev_to_net_device() has a put_device() call which is missing in
dsa_port_parse_of(), but we can actually even verify that an issue
exists. With CONFIG_DEBUG_KOBJECT_RELEASE=y, if we run this command
"before" and "after" applying this patch:
(unbind the conduit driver for net device eno2)
echo 0000:00:00.2 > /sys/bus/pci/drivers/fsl_enetc/unbind
we see these lines in the output diff which appear only with the patch
applied:
kobject: 'eno2' (ffff002009a3a6b8): kobject_release, parent 0000000000000000 (delayed 1000)
kobject: '109' (ffff0020099d59a0): kobject_release, parent 0000000000000000 (delayed 1000)
2. After we find the conduit interface one way (OF) or another (non-OF),
it can get unregistered at any time, and DSA remains with a long-lived,
but in this case stale, cpu_dp->conduit pointer. Holding the net
device's underlying kobject isn't actually of much help, it just
prevents it from being freed (but we never need that kobject
directly). What helps us to prevent the net device from being
unregistered is the parallel netdev reference mechanism (dev_hold()
and dev_put()).
Actually we actually use that netdev tracker mechanism implicitly on
user ports since commit 2f1e8ea726 ("net: dsa: link interfaces with
the DSA master to get rid of lockdep warnings"), via netdev_upper_dev_link().
But time still passes at DSA switch probe time between the initial
of_find_net_device_by_node() code and the user port creation time, time
during which the conduit could unregister itself and DSA wouldn't know
about it.
So we have to run of_find_net_device_by_node() under rtnl_lock() to
prevent that from happening, and release the lock only with the netdev
tracker having acquired the reference.
Do we need to keep the reference until dsa_unregister_switch() /
dsa_switch_shutdown()?
1: Maybe yes. A switch device will still be registered even if all user
ports failed to probe, see commit 86f8b1c01a ("net: dsa: Do not
make user port errors fatal"), and the cpu_dp->conduit pointers
remain valid. I haven't audited all call paths to see whether they
will actually use the conduit in lack of any user port, but if they
do, it seems safer to not rely on user ports for that reference.
2. Definitely yes. We support changing the conduit which a user port is
associated to, and we can get into a situation where we've moved all
user ports away from a conduit, thus no longer hold any reference to
it via the net device tracker. But we shouldn't let it go nonetheless
- see the next change in relation to dsa_tree_find_first_conduit()
and LAG conduits which disappear.
We have to be prepared to return to the physical conduit, so the CPU
port must explicitly keep another reference to it. This is also to
say: the user ports and their CPU ports may not always keep a
reference to the same conduit net device, and both are needed.
As for the conduit's kobject for the /sys/class/net/ entry, we don't
care about it, we can release it as soon as we hold the net device
object itself.
History and blame attribution
-----------------------------
The code has been refactored so many times, it is very difficult to
follow and properly attribute a blame, but I'll try to make a short
history which I hope to be correct.
We have two distinct probing paths:
- one for OF, introduced in 2016 in commit 83c0afaec7 ("net: dsa: Add
new binding implementation")
- one for non-OF, introduced in 2017 in commit 71e0bbde0d ("net: dsa:
Add support for platform data")
These are both complete rewrites of the original probing paths (which
used struct dsa_switch_driver and other weird stuff, instead of regular
devices on their respective buses for register access, like MDIO, SPI,
I2C etc):
- one for OF, introduced in 2013 in commit 5e95329b70 ("dsa: add
device tree bindings to register DSA switches")
- one for non-OF, introduced in 2008 in commit 91da11f870 ("net:
Distributed Switch Architecture protocol support")
except for tiny bits and pieces like dsa_dev_to_net_device() which were
seemingly carried over since the original commit, and used to this day.
The point is that the original probing paths received a fix in 2015 in
the form of commit 679fb46c57 ("net: dsa: Add missing master netdev
dev_put() calls"), but the fix never made it into the "new" (dsa2)
probing paths that can still be traced to today, and the fixed probing
path was later deleted in 2019 in commit 93e86b3bc8 ("net: dsa: Remove
legacy probing support").
That is to say, the new probing paths were never quite correct in this
area.
The existence of the legacy probing support which was deleted in 2019
explains why dsa_dev_to_net_device() returns a conduit with elevated
refcount (because it was supposed to be released during
dsa_remove_dst()). After the removal of the legacy code, the only user
of dsa_dev_to_net_device() calls dev_put(conduit) immediately after this
function returns. This pattern makes no sense today, and can only be
interpreted historically to understand why dev_hold() was there in the
first place.
Change details
--------------
Today we have a better netdev tracking infrastructure which we should
use. Logically netdev_hold() belongs in common code
(dsa_port_parse_cpu(), where dp->conduit is assigned), but there is a
tradeoff to be made with the rtnl_lock() section which would become a
bit too long if we did that - dsa_port_parse_cpu() also calls
request_module(). So we duplicate a bit of logic in order for the
callers of dsa_port_parse_cpu() to be the ones responsible of holding
the conduit reference and releasing it on error. This shortens the
rtnl_lock() section significantly.
In the dsa_switch_probe() error path, dsa_switch_release_ports() will be
called in a number of situations, one being where dsa_port_parse_cpu()
maybe didn't get the chance to run at all (a different port failed
earlier, etc). So we have to test for the conduit being NULL prior to
calling netdev_put().
There have still been so many transformations to the code since the
blamed commits (rename master -> conduit, commit 0650bf52b3 ("net:
dsa: be compatible with masters which unregister on shutdown")), that it
only makes sense to fix the code using the best methods available today
and see how it can be backported to stable later. I suspect the fix
cannot even be backported to kernels which lack dsa_switch_shutdown(),
and I suspect this is also maybe why the long-lived conduit reference
didn't make it into the new DSA probing paths at the time (problems
during shutdown).
Because dsa_dev_to_net_device() has a single call site and has to be
changed anyway, the logic was just absorbed into the non-OF
dsa_port_parse().
Tested on the ocelot/felix switch and on dsa_loop, both on the NXP
LS1028A with CONFIG_DEBUG_KOBJECT_RELEASE=y.
Reported-by: Ma Ke <make24@iscas.ac.cn>
Closes: https://lore.kernel.org/netdev/20251214131204.4684-1-make24@iscas.ac.cn/
Fixes: 83c0afaec7 ("net: dsa: Add new binding implementation")
Fixes: 71e0bbde0d ("net: dsa: Add support for platform data")
Reviewed-by: Jonas Gorski <jonas.gorski@gmail.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Link: https://patch.msgid.link/20251215150236.3931670-1-vladimir.oltean@nxp.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5e7365b5a1 ]
Since airoha_probe() is not executed under rtnl lock, there is small race
where a given device is configured by user-space while the remaining ones
are not completely loaded from the dts yet. This condition will allow a
hw device misconfiguration since there are some conditions (e.g. GDM2 check
in airoha_dev_init()) that require all device are properly loaded from the
device tree. Fix the issue moving net_devices registration at the end of
the airoha_probe routine.
Fixes: 9cd451d414 ("net: airoha: Add loopback support for GDM2")
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20251214-airoha-fix-dev-registration-v1-1-860e027ad4c6@kernel.org
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 15dd100349 ]
The ibm_rtl_init() function searches for the signature but has a pointer
arithmetic error. The loop counter suggests searching at 4-byte intervals
but the implementation only advances by 1 byte per iteration.
Fix by properly advancing the pointer by sizeof(unsigned int) bytes
each iteration.
Reported-by: Yuhao Jiang <danisjiang@gmail.com>
Reported-by: Junrui Luo <moonafterrain@outlook.com>
Fixes: 35f0ce032b ("IBM Real-Time "SMI Free" mode driver -v7")
Signed-off-by: Junrui Luo <moonafterrain@outlook.com>
Link: https://patch.msgid.link/SYBPR01MB78812D887A92DE3802D0D06EAFA9A@SYBPR01MB7881.ausprd01.prod.outlook.com
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1461209cf8 ]
A sysfs group is created in msi_init() when old_ec_model is enabled, but
never removed. Remove the msipf_old_attribute_group in that case.
Fixes: 03696e51d7 ("msi-laptop: Disable brightness control for new EC")
Signed-off-by: Thomas Fourier <fourier.thomas@gmail.com>
Link: https://patch.msgid.link/20251217103617.27668-2-fourier.thomas@gmail.com
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f13bce715d ]
Some event names have trailing whitespaces at the end which causes programming
of counters using the name for these specific events to fail and hence need to
be removed.
Fixes: 423c336185 ("platform/mellanox: mlxbf-pmc: Add support for BlueField-3")
Signed-off-by: Shravan Kumar Ramani <shravankr@nvidia.com>
Reviewed-by: David Thompson <davthompson@nvidia.com>
Link: https://patch.msgid.link/065cbae0717dcc1169681c4dbb1a6e050b8574b3.1766059953.git.shravankr@nvidia.com
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit db5b4e39c4 ]
Over the years, syzbot found many ways to crash the kernel
in ip6gre_header() [1].
This involves team or bonding drivers ability to dynamically
change their dev->needed_headroom and/or dev->hard_header_len
In this particular crash mld_newpack() allocated an skb
with a too small reserve/headroom, and by the time mld_sendpack()
was called, syzbot managed to attach an ip6gre device.
[1]
skbuff: skb_under_panic: text:ffffffff8a1d69a8 len:136 put:40 head:ffff888059bc7000 data:ffff888059bc6fe8 tail:0x70 end:0x6c0 dev:team0
------------[ cut here ]------------
kernel BUG at net/core/skbuff.c:213 !
<TASK>
skb_under_panic net/core/skbuff.c:223 [inline]
skb_push+0xc3/0xe0 net/core/skbuff.c:2641
ip6gre_header+0xc8/0x790 net/ipv6/ip6_gre.c:1371
dev_hard_header include/linux/netdevice.h:3436 [inline]
neigh_connected_output+0x286/0x460 net/core/neighbour.c:1618
neigh_output include/net/neighbour.h:556 [inline]
ip6_finish_output2+0xfb3/0x1480 net/ipv6/ip6_output.c:136
__ip6_finish_output net/ipv6/ip6_output.c:-1 [inline]
ip6_finish_output+0x234/0x7d0 net/ipv6/ip6_output.c:220
NF_HOOK_COND include/linux/netfilter.h:307 [inline]
ip6_output+0x340/0x550 net/ipv6/ip6_output.c:247
NF_HOOK+0x9e/0x380 include/linux/netfilter.h:318
mld_sendpack+0x8d4/0xe60 net/ipv6/mcast.c:1855
mld_send_cr net/ipv6/mcast.c:2154 [inline]
mld_ifc_work+0x83e/0xd60 net/ipv6/mcast.c:2693
Fixes: c12b395a46 ("gre: Support GRE over IPv6")
Reported-by: syzbot+43a2ebcf2a64b1102d64@syzkaller.appspotmail.com
Closes: https://lore.kernel.org/netdev/693b002c.a70a0220.33cd7b.0033.GAE@google.com/T/#u
Signed-off-by: Eric Dumazet <edumazet@google.com>
Link: https://patch.msgid.link/20251211173550.2032674-1-edumazet@google.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5498227676 ]
The openvswitch teardown code will immediately call
ovs_netdev_detach_dev() in response to a NETDEV_UNREGISTER notification.
It will then start the dp_notify_work workqueue, which will later end up
calling the vport destroy() callback. This callback takes the RTNL to do
another ovs_netdev_detach_port(), which in this case is unnecessary.
This causes extra pressure on the RTNL, in some cases leading to
"unregister_netdevice: waiting for XX to become free" warnings on
teardown.
We can straight-forwardly avoid the extra RTNL lock acquisition by
checking the device flags before taking the lock, and skip the locking
altogether if the IFF_OVS_DATAPATH flag has already been unset.
Fixes: b07c26511e ("openvswitch: fix vport-netdev unregister")
Tested-by: Adrian Moreno <amorenoz@redhat.com>
Signed-off-by: Toke Høiland-Jørgensen <toke@redhat.com>
Acked-by: Eelco Chaudron <echaudro@redhat.com>
Acked-by: Aaron Conole <aconole@redhat.com>
Link: https://patch.msgid.link/20251211115006.228876-1-toke@redhat.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d1a1a4bade ]
The Aspeed MDIO controller may return incorrect data when a read operation
follows immediately after a write. Due to a controller bug, the subsequent
read can latch stale data, causing the polling logic to terminate earlier
than expected.
To work around this hardware issue, insert a dummy read after each write
operation. This ensures that the next actual read returns the correct
data and prevents premature polling exit.
This workaround has been verified to stabilize MDIO transactions on
affected Aspeed platforms.
Fixes: f160e99462 ("net: phy: Add mdio-aspeed")
Signed-off-by: Jacky Chou <jacky_chou@aspeedtech.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/20251211-aspeed_mdio_add_dummy_read-v3-1-382868869004@aspeedtech.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 252714f1e8 ]
This reverts commit 98921dbd00 ("Bluetooth: Use devm_kzalloc in
btusb.c file").
In btusb_probe(), we use devm_kzalloc() to allocate the btusb data. This
ties the lifetime of all the btusb data to the binding of a driver to
one interface, INTF. In a driver that binds to other interfaces, ISOC
and DIAG, this is an accident waiting to happen.
The issue is revealed in btusb_disconnect(), where calling
usb_driver_release_interface(&btusb_driver, data->intf) will have devm
free the data that is also being used by the other interfaces of the
driver that may not be released yet.
To fix this, revert the use of devm and go back to freeing memory
explicitly.
Fixes: 98921dbd00 ("Bluetooth: Use devm_kzalloc in btusb.c file")
Signed-off-by: Raphael Pinsonneault-Thibeault <rpthibeault@gmail.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 348240e5fa ]
MGMT_SETTING_ISO_BROADCASTER and MGMT_SETTING_ISO_RECEIVER flags are
missing from supported_settings although they are in current_settings.
Report them also in supported_settings to be consistent.
Fixes: ae75336131 ("Bluetooth: Check for ISO support in controller")
Signed-off-by: Pauli Virtanen <pav@iki.fi>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 50fdb78b7c ]
As soon as crypto_aead_encrypt is called, the underlying request
may be freed by an asynchronous completion. Thus dereferencing
req->iv after it returns is invalid.
Instead of checking req->iv against info, create a new variable
unaligned_info and use it for that purpose instead.
Fixes: 0a270321db ("[CRYPTO] seqiv: Add Sequence Number IV Generator")
Reported-by: Xiumei Mu <xmu@redhat.com>
Reported-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit aa7d3a56a2 ]
A warning was triggered as follows:
WARNING: kernel/cgroup/cpuset.c:1651 at remote_partition_disable+0xf7/0x110
RIP: 0010:remote_partition_disable+0xf7/0x110
RSP: 0018:ffffc90001947d88 EFLAGS: 00000206
RAX: 0000000000007fff RBX: ffff888103b6e000 RCX: 0000000000006f40
RDX: 0000000000006f00 RSI: ffffc90001947da8 RDI: ffff888103b6e000
RBP: ffff888103b6e000 R08: 0000000000000000 R09: 0000000000000000
R10: 0000000000000001 R11: ffff88810b2e2728 R12: ffffc90001947da8
R13: 0000000000000000 R14: ffffc90001947da8 R15: ffff8881081f1c00
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 00007f55c8bbe0b2 CR3: 000000010b14c000 CR4: 00000000000006f0
Call Trace:
<TASK>
update_prstate+0x2d3/0x580
cpuset_partition_write+0x94/0xf0
kernfs_fop_write_iter+0x147/0x200
vfs_write+0x35d/0x500
ksys_write+0x66/0xe0
do_syscall_64+0x6b/0x390
entry_SYSCALL_64_after_hwframe+0x4b/0x53
RIP: 0033:0x7f55c8cd4887
Reproduction steps (on a 16-CPU machine):
# cd /sys/fs/cgroup/
# mkdir A1
# echo +cpuset > A1/cgroup.subtree_control
# echo "0-14" > A1/cpuset.cpus.exclusive
# mkdir A1/A2
# echo "0-14" > A1/A2/cpuset.cpus.exclusive
# echo "root" > A1/A2/cpuset.cpus.partition
# echo 0 > /sys/devices/system/cpu/cpu15/online
# echo member > A1/A2/cpuset.cpus.partition
When CPU 15 is offlined, subpartitions_cpus gets cleared because no CPUs
remain available for the top_cpuset, forcing partitions to share CPUs with
the top_cpuset. In this scenario, disabling the remote partition triggers
a warning stating that effective_xcpus is not a subset of
subpartitions_cpus. Partitions should be invalidated in this case to
inform users that the partition is now invalid(cpus are shared with
top_cpuset).
To fix this issue:
1. Only emit the warning only if subpartitions_cpus is not empty and the
effective_xcpus is not a subset of subpartitions_cpus.
2. During the CPU hotplug process, invalidate partitions if
subpartitions_cpus is empty.
Fixes: f62a5d3936 ("cgroup/cpuset: Remove remote_partition_check() & make update_cpumasks_hier() handle remote partition")
Signed-off-by: Chen Ridong <chenridong@huawei.com>
Reviewed-by: Waiman Long <longman@redhat.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b3d6bbae1d ]
During the IDPF init phase, the mailbox runs in poll mode until it is
configured to properly handle interrupts. The previous delay of 300ms is
excessively long for the mailbox polling mechanism, which causes a slow
initialization of ~2s:
echo 0000:06:12.4 > /sys/bus/pci/drivers/idpf/bind
[ 52.444239] idpf 0000:06:12.4: enabling device (0000 -> 0002)
[ 52.485005] idpf 0000:06:12.4: Device HW Reset initiated
[ 54.177181] idpf 0000:06:12.4: PTP init failed, err=-EOPNOTSUPP
[ 54.206177] idpf 0000:06:12.4: Minimum RX descriptor support not provided, using the default
[ 54.206182] idpf 0000:06:12.4: Minimum TX descriptor support not provided, using the default
Changing the delay to 300us avoids the delays during the initial mailbox
transactions, making the init phase much faster:
[ 83.342590] idpf 0000:06:12.4: enabling device (0000 -> 0002)
[ 83.384402] idpf 0000:06:12.4: Device HW Reset initiated
[ 83.518323] idpf 0000:06:12.4: PTP init failed, err=-EOPNOTSUPP
[ 83.547430] idpf 0000:06:12.4: Minimum RX descriptor support not provided, using the default
[ 83.547435] idpf 0000:06:12.4: Minimum TX descriptor support not provided, using the default
Fixes: 4930fbf419 ("idpf: add core init and interrupt request")
Signed-off-by: Brian Vazquez <brianvv@google.com>
Reviewed-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Tested-by: Samuel Salin <Samuel.salin@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4af1f9a472 ]
IPU SDK versions 1.9 through 2.0.5 require send buffer to contain a single
empty memory region. Set number of regions to 1 and use appropriate send
buffer size to satisfy this requirement.
Fixes: 6aa53e861c ("idpf: implement get LAN MMIO memory regions")
Suggested-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com>
Reviewed-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Signed-off-by: Larysa Zaremba <larysa.zaremba@intel.com>
Tested-by: Krishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6daa2893f3 ]
There are off-by-one bugs when configuring RSS hash key and lookup
table, causing out-of-bounds reads to memory [1] and out-of-bounds
writes to device registers.
Before commit 43a3d9ba34 ("i40evf: Allow PF driver to configure RSS"),
the loop upper bounds were:
i <= I40E_VFQF_{HKEY,HLUT}_MAX_INDEX
which is safe since the value is the last valid index.
That commit changed the bounds to:
i <= adapter->rss_{key,lut}_size / 4
where `rss_{key,lut}_size / 4` is the number of dwords, so the last
valid index is `(rss_{key,lut}_size / 4) - 1`. Therefore, using `<=`
accesses one element past the end.
Fix the issues by using `<` instead of `<=`, ensuring we do not exceed
the bounds.
[1] KASAN splat about rss_key_size off-by-one
BUG: KASAN: slab-out-of-bounds in iavf_config_rss+0x619/0x800
Read of size 4 at addr ffff888102c50134 by task kworker/u8:6/63
CPU: 0 UID: 0 PID: 63 Comm: kworker/u8:6 Not tainted 6.18.0-rc2-enjuk-tnguy-00378-g3005f5b77652-dirty #156 PREEMPT(voluntary)
Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS 1.16.3-debian-1.16.3-2 04/01/2014
Workqueue: iavf iavf_watchdog_task
Call Trace:
<TASK>
dump_stack_lvl+0x6f/0xb0
print_report+0x170/0x4f3
kasan_report+0xe1/0x1a0
iavf_config_rss+0x619/0x800
iavf_watchdog_task+0x2be7/0x3230
process_one_work+0x7fd/0x1420
worker_thread+0x4d1/0xd40
kthread+0x344/0x660
ret_from_fork+0x249/0x320
ret_from_fork_asm+0x1a/0x30
</TASK>
Allocated by task 63:
kasan_save_stack+0x30/0x50
kasan_save_track+0x14/0x30
__kasan_kmalloc+0x7f/0x90
__kmalloc_noprof+0x246/0x6f0
iavf_watchdog_task+0x28fc/0x3230
process_one_work+0x7fd/0x1420
worker_thread+0x4d1/0xd40
kthread+0x344/0x660
ret_from_fork+0x249/0x320
ret_from_fork_asm+0x1a/0x30
The buggy address belongs to the object at ffff888102c50100
which belongs to the cache kmalloc-64 of size 64
The buggy address is located 0 bytes to the right of
allocated 52-byte region [ffff888102c50100, ffff888102c50134)
The buggy address belongs to the physical page:
page: refcount:0 mapcount:0 mapping:0000000000000000 index:0x0 pfn:0x102c50
flags: 0x200000000000000(node=0|zone=2)
page_type: f5(slab)
raw: 0200000000000000 ffff8881000418c0 dead000000000122 0000000000000000
raw: 0000000000000000 0000000080200020 00000000f5000000 0000000000000000
page dumped because: kasan: bad access detected
Memory state around the buggy address:
ffff888102c50000: 00 00 00 00 00 00 00 fc fc fc fc fc fc fc fc fc
ffff888102c50080: 00 00 00 00 00 00 00 fc fc fc fc fc fc fc fc fc
>ffff888102c50100: 00 00 00 00 00 00 04 fc fc fc fc fc fc fc fc fc
^
ffff888102c50180: 00 00 00 00 00 00 00 00 fc fc fc fc fc fc fc fc
ffff888102c50200: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc
Fixes: 43a3d9ba34 ("i40evf: Allow PF driver to configure RSS")
Signed-off-by: Kohei Enju <enjuk@amazon.com>
Reviewed-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Tested-by: Rafal Romanowski <rafal.romanowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6994283421 ]
The maximum number of descriptors supported by the hardware is
hardware-dependent and can be retrieved using
i40e_get_max_num_descriptors(). Move this function to a shared header
and use it when checking for valid ring_len parameter rather than using
hardcoded value.
By fixing an over-acceptance issue, behavior change could be seen where
ring_len could now be rejected while configuring rx and tx queues if its
size is larger than the hardware-dependent maximum number of
descriptors.
Fixes: 55d225670d ("i40e: add validation for ring_len param")
Signed-off-by: Gregory Herrero <gregory.herrero@oracle.com>
Tested-by: Rafal Romanowski <rafal.romanowski@intel.com>
Reviewed-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit be43abc551 ]
Add service task schedule to set_rx_mode.
In some cases there are error messages printed out in PTP application
(ptp4l):
ptp4l[13848.762]: port 1 (ens2f3np3): received SYNC without timestamp
ptp4l[13848.825]: port 1 (ens2f3np3): received SYNC without timestamp
ptp4l[13848.887]: port 1 (ens2f3np3): received SYNC without timestamp
This happens when service task would not run immediately after
set_rx_mode, and we need it for setup tasks. This service task checks, if
PTP RX packets are hung in firmware, and propagate correct settings such
as multicast address for IEEE 1588 Precision Time Protocol.
RX timestamping depends on some of these filters set. Bug happens only
with high PTP packets frequency incoming, and not every run since
sometimes service task is being ran from a different place immediately
after starting ptp4l.
Fixes: 0e4425ed64 ("i40e: fix: do not sleep in netdev_ops")
Reviewed-by: Grzegorz Nitka <grzegorz.nitka@intel.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Signed-off-by: Przemyslaw Korba <przemyslaw.korba@intel.com>
Tested-by: Rinitha S <sx.rinitha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b0101ccb5b ]
Smatch reported:
kernel/sched/ext.c:5332 scx_alloc_and_add_sched() warn: passing zero to 'ERR_PTR'
In scx_alloc_and_add_sched(), the alloc_percpu() failure path jumps to
err_free_gdsqs without initializing @ret. That can lead to returning
ERR_PTR(0), which violates the ERR_PTR() convention and confuses
callers.
Set @ret to -ENOMEM before jumping to the error path when
alloc_percpu() fails.
Reported-by: kernel test robot <lkp@intel.com>
Closes: https://lore.kernel.org/r/202512141601.yAXDAeA9-lkp@intel.com/
Reported-by: Dan Carpenter <error27@gmail.com>
Fixes: c201ea1578 ("sched_ext: Move event_stats_cpu into scx_sched")
Signed-off-by: Liang Jie <liangjie@lixiang.com>
Reviewed-by: Emil Tsalapatis <emil@etsalapatis.com>
Reviewed-by: Andrea Righi <arighi@nvidia.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a519be2f5d ]
When userspace brings down and deletes a non-transmitted profile,
it is expected to send a new updated Beacon template for the
transmitted profile of that multiple BSSID (MBSSID) group which
does not include the removed profile in MBSSID element. This
update comes via NL80211_CMD_SET_BEACON.
Such updates work well as long as the group continues to have at
least one non-transmitted profile as NL80211_ATTR_MBSSID_ELEMS
is included in the new Beacon template.
But when the last non-trasmitted profile is removed, it still
gets included in Beacon templates sent to driver. This happens
because when no MBSSID elements are sent by the userspace,
ieee80211_assign_beacon() ends up using the element stored from
earlier Beacon template.
Do not copy old MBSSID elements, instead userspace should always
include these when applicable.
Fixes: 2b3171c6fe ("mac80211: MBSSID beacon handling in AP mode")
Signed-off-by: Aloka Dixit <aloka.dixit@oss.qualcomm.com>
Link: https://patch.msgid.link/20251215174656.2866319-2-aloka.dixit@oss.qualcomm.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2b77b9551d ]
The QGenie AI code review tool says we should store the capped length to
wdev->u.client.ssid_len. The AI is correct.
Fixes: 62b635dcd6 ("wifi: cfg80211: sme: cap SSID length in __cfg80211_connect_result()")
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
Link: https://patch.msgid.link/aTAbp5RleyH_lnZE@stanley.mountain
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit dd39edb445 ]
TID getting from ieee80211_get_tid() might be out of range of array size
of sta_entry->tids[], so check TID is less than MAX_TID_COUNT. Othwerwise,
UBSAN warn:
UBSAN: array-index-out-of-bounds in drivers/net/wireless/realtek/rtlwifi/rtl8192cu/trx.c:514:30
index 10 is out of range for type 'rtl_tid_data [9]'
Fixes: 8ca4cdef93 ("wifi: rtlwifi: rtl8192cu: Fix TX aggregation")
Signed-off-by: Morning Star <alexbestoso@gmail.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://patch.msgid.link/1764232628-13625-1-git-send-email-pkshih@realtek.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit eb296c0980 upstream.
SI hardware doesn't support pasids, user mode queues, or
KIQ/MES so there is no need for this. Doing so results in
a segfault as these callbacks are non-existent for SI.
Closes: https://gitlab.freedesktop.org/drm/amd/-/issues/4744
Fixes: f3854e04b7 ("drm/amdgpu: attach tlb fence to the PTs update")
Reviewed-by: Timur Kristóf <timur.kristof@gmail.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
(cherry picked from commit 820b3d376e)
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 83cbb4d33d ]
Add a mechanism for DisplayID specific quirks, and add the first quirk
to ignore DisplayID section checksum errors.
It would be quite inconvenient to pass existing EDID quirks from
drm_edid.c for DisplayID parsing. Not all places doing DisplayID
iteration have the quirks readily available, and would have to pass it
in all places. Simply add a separate array of DisplayID specific EDID
quirks. We do end up checking it every time we iterate DisplayID blocks,
but hopefully the number of quirks remains small.
There are a few laptop models with DisplayID checksum failures, leading
to higher refresh rates only present in the DisplayID blocks being
ignored. Add a quirk for the panel in the machines.
Reported-by: Tiago Martins Araújo <tiago.martins.araujo@gmail.com>
Closes: https://lore.kernel.org/r/CACRbrPGvLP5LANXuFi6z0S7XMbAG4X5y2YOLBDxfOVtfGGqiKQ@mail.gmail.com
Closes: https://gitlab.freedesktop.org/drm/i915/kernel/-/issues/14703
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Tested-by: Tiago Martins Araújo <tiago.martins.araujo@gmail.com>
Cc: stable@vger.kernel.org
Link: https://patch.msgid.link/c04d81ae648c5f21b3f5b7953f924718051f2798.1761681968.git.jani.nikula@intel.com
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 2f393c228c ]
A few checks were missing in gmap_helper_zap_one_page(), which can lead
to memory corruption in the guest under specific circumstances.
Add the missing checks.
Fixes: 5deafa27d9 ("KVM: s390: Fix to clear PTE when discarding a swapped page")
Cc: stable@vger.kernel.org
Reported-by: Marc Hartmayer <mhartmay@linux.ibm.com>
Tested-by: Marc Hartmayer <mhartmay@linux.ibm.com>
Acked-by: Christian Borntraeger <borntraeger@linux.ibm.com>
Signed-off-by: Claudio Imbrenda <imbrenda@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
[ adapted ptep_zap_softleaf_entry() and softleaf_from_pte() calls to ptep_zap_swap_entry() and pte_to_swp_entry() ]
Signed-off-by: Sasha Levin <sashal@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 8a0e4bdddd ]
uniform_split_supported() and non_uniform_split_supported() share
significantly similar logic.
The only functional difference is that uniform_split_supported() includes
an additional check on the requested @new_order.
The reason for this check comes from the following two aspects:
* some file system or swap cache just supports order-0 folio
* the behavioral difference between uniform/non-uniform split
The behavioral difference between uniform split and non-uniform:
* uniform split splits folio directly to @new_order
* non-uniform split creates after-split folios with orders from
folio_order(folio) - 1 to new_order.
This means for non-uniform split or !new_order split we should check the
file system and swap cache respectively.
This commit unifies the logic and merge the two functions into a single
combined helper, removing redundant code and simplifying the split
support checking mechanism.
Link: https://lkml.kernel.org/r/20251106034155.21398-3-richard.weiyang@gmail.com
Fixes: c010d47f10 ("mm: thp: split huge page to any lower order pages")
Signed-off-by: Wei Yang <richard.weiyang@gmail.com>
Reviewed-by: Zi Yan <ziy@nvidia.com>
Cc: Zi Yan <ziy@nvidia.com>
Cc: "David Hildenbrand (Red Hat)" <david@kernel.org>
Cc: Baolin Wang <baolin.wang@linux.alibaba.com>
Cc: Barry Song <baohua@kernel.org>
Cc: Dev Jain <dev.jain@arm.com>
Cc: Lance Yang <lance.yang@linux.dev>
Cc: Liam Howlett <liam.howlett@oracle.com>
Cc: Lorenzo Stoakes <lorenzo.stoakes@oracle.com>
Cc: Nico Pache <npache@redhat.com>
Cc: Ryan Roberts <ryan.roberts@arm.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
[ split_type => uniform_split and replaced SPLIT_TYPE_NON_UNIFORM checks ]
Signed-off-by: Sasha Levin <sashal@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 1dd6c84f1c ]
When loading the ebpf scheduler, the tasks in the scx_tasks list will
be traversed and invoke __setscheduler_class() to get new sched_class.
however, this would also incorrectly set the per-cpu migration
task's->sched_class to rt_sched_class, even after unload, the per-cpu
migration task's->sched_class remains sched_rt_class.
The log for this issue is as follows:
./scx_rustland --stats 1
[ 199.245639][ T630] sched_ext: "rustland" does not implement cgroup cpu.weight
[ 199.269213][ T630] sched_ext: BPF scheduler "rustland" enabled
04:25:09 [INFO] RustLand scheduler attached
bpftrace -e 'iter:task /strcontains(ctx->task->comm, "migration")/
{ printf("%s:%d->%pS\n", ctx->task->comm, ctx->task->pid, ctx->task->sched_class); }'
Attaching 1 probe...
migration/0:24->rt_sched_class+0x0/0xe0
migration/1:27->rt_sched_class+0x0/0xe0
migration/2:33->rt_sched_class+0x0/0xe0
migration/3:39->rt_sched_class+0x0/0xe0
migration/4:45->rt_sched_class+0x0/0xe0
migration/5:52->rt_sched_class+0x0/0xe0
migration/6:58->rt_sched_class+0x0/0xe0
migration/7:64->rt_sched_class+0x0/0xe0
sched_ext: BPF scheduler "rustland" disabled (unregistered from user space)
EXIT: unregistered from user space
04:25:21 [INFO] Unregister RustLand scheduler
bpftrace -e 'iter:task /strcontains(ctx->task->comm, "migration")/
{ printf("%s:%d->%pS\n", ctx->task->comm, ctx->task->pid, ctx->task->sched_class); }'
Attaching 1 probe...
migration/0:24->rt_sched_class+0x0/0xe0
migration/1:27->rt_sched_class+0x0/0xe0
migration/2:33->rt_sched_class+0x0/0xe0
migration/3:39->rt_sched_class+0x0/0xe0
migration/4:45->rt_sched_class+0x0/0xe0
migration/5:52->rt_sched_class+0x0/0xe0
migration/6:58->rt_sched_class+0x0/0xe0
migration/7:64->rt_sched_class+0x0/0xe0
This commit therefore generate a new scx_setscheduler_class() and
add check for stop_sched_class to replace __setscheduler_class().
Fixes: f0e1a0643a ("sched_ext: Implement BPF extensible scheduler class")
Cc: stable@vger.kernel.org # v6.12+
Signed-off-by: Zqiang <qiang.zhang@linux.dev>
Reviewed-by: Andrea Righi <arighi@nvidia.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
[ Adjust context ]
Signed-off-by: Sasha Levin <sashal@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 79f3f9bedd ]
Basically, from the constraint that the sum of lag is zero, you can
infer that the 0-lag point is the weighted average of the individual
vruntime, which is what we're trying to compute:
\Sum w_i * v_i
avg = --------------
\Sum w_i
Now, since vruntime takes the whole u64 (worse, it wraps), this
multiplication term in the numerator is not something we can compute;
instead we do the min_vruntime (v0 henceforth) thing like:
v_i = (v_i - v0) + v0
This does two things:
- it keeps the key: (v_i - v0) 'small';
- it creates a relative 0-point in the modular space.
If you do that subtitution and work it all out, you end up with:
\Sum w_i * (v_i - v0)
avg = --------------------- + v0
\Sum w_i
Since you cannot very well track a ratio like that (and not suffer
terrible numerical problems) we simpy track the numerator and
denominator individually and only perform the division when strictly
needed.
Notably, the numerator lives in cfs_rq->avg_vruntime and the denominator
lives in cfs_rq->avg_load.
The one extra 'funny' is that these numbers track the entities in the
tree, and current is typically outside of the tree, so avg_vruntime()
adds current when needed before doing the division.
(vruntime_eligible() elides the division by cross-wise multiplication)
Anyway, as mentioned above, we currently use the CFS era min_vruntime
for this purpose. However, this thing can only move forward, while the
above avg can in fact move backward (when a non-eligible task leaves,
the average becomes smaller), this can cause trouble when through
happenstance (or construction) these values drift far enough apart to
wreck the game.
Replace cfs_rq::min_vruntime with cfs_rq::zero_vruntime which is kept
near/at avg_vruntime, following its motion.
The down-side is that this requires computing the avg more often.
Fixes: 147f3efaa2 ("sched/fair: Implement an EEVDF-like scheduling policy")
Reported-by: Zicheng Qu <quzicheng@huawei.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Link: https://patch.msgid.link/20251106111741.GC4068168@noisy.programming.kicks-ass.net
Cc: stable@vger.kernel.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8d17104506 upstream.
All microcode patches up to the proper BIOS Entrysign fix are loaded
only after the sha256 signature carried in the driver has been verified.
Microcode patches after the Entrysign fix has been applied, do not need
that signature verification anymore.
In order to not abandon machines which haven't received the BIOS update
yet, add the capability to select which microcode patch to load.
The corresponding microcode container supplied through firmware-linux
has been modified to carry two patches per CPU type
(family/model/stepping) so that the proper one gets selected.
Signed-off-by: Borislav Petkov (AMD) <bp@alien8.de>
Tested-by: Waiman Long <longman@redhat.com>
Link: https://patch.msgid.link/20251027133818.4363-1-bp@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 127b90315c upstream.
When executing a task in proxy context, handle yields as if they were
requested by the donor task. This matches the traditional PI semantics
of yield() as well.
This avoids scenario like proxy task yielding, pick next task selecting the
same previous blocked donor, running the proxy task again, etc.
Reported-by: kernel test robot <oliver.sang@intel.com>
Closes: https://lore.kernel.org/oe-lkp/202510211205.1e0f5223-lkp@intel.com
Suggested-by: Peter Zijlstra <peterz@infradead.org>
Signed-off-by: Fernand Sieber <sieberf@amazon.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Link: https://patch.msgid.link/20251106104022.195157-1-sieberf@amazon.com
Cc: Holger Hoffstätte <holger@applied-asynchrony.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit bd5603eaae upstream.
Commit e26ee4efbc ("fuse: allocate ff->release_args only if release is
needed") skips allocating ff->release_args if the server does not
implement open. However in doing so, fuse_prepare_release() now skips
grabbing the reference on the inode, which makes it possible for an
inode to be evicted from the dcache while there are inflight readahead
requests. This causes a deadlock if the server triggers reclaim while
servicing the readahead request and reclaim attempts to evict the inode
of the file being read ahead. Since the folio is locked during
readahead, when reclaim evicts the fuse inode and fuse_evict_inode()
attempts to remove all folios associated with the inode from the page
cache (truncate_inode_pages_range()), reclaim will block forever waiting
for the lock since readahead cannot relinquish the lock because it is
itself blocked in reclaim:
>>> stack_trace(1504735)
folio_wait_bit_common (mm/filemap.c:1308:4)
folio_lock (./include/linux/pagemap.h:1052:3)
truncate_inode_pages_range (mm/truncate.c:336:10)
fuse_evict_inode (fs/fuse/inode.c:161:2)
evict (fs/inode.c:704:3)
dentry_unlink_inode (fs/dcache.c:412:3)
__dentry_kill (fs/dcache.c:615:3)
shrink_kill (fs/dcache.c:1060:12)
shrink_dentry_list (fs/dcache.c:1087:3)
prune_dcache_sb (fs/dcache.c:1168:2)
super_cache_scan (fs/super.c:221:10)
do_shrink_slab (mm/shrinker.c:435:9)
shrink_slab (mm/shrinker.c:626:10)
shrink_node (mm/vmscan.c:5951:2)
shrink_zones (mm/vmscan.c:6195:3)
do_try_to_free_pages (mm/vmscan.c:6257:3)
do_swap_page (mm/memory.c:4136:11)
handle_pte_fault (mm/memory.c:5562:10)
handle_mm_fault (mm/memory.c:5870:9)
do_user_addr_fault (arch/x86/mm/fault.c:1338:10)
handle_page_fault (arch/x86/mm/fault.c:1481:3)
exc_page_fault (arch/x86/mm/fault.c:1539:2)
asm_exc_page_fault+0x22/0x27
Fix this deadlock by allocating ff->release_args and grabbing the
reference on the inode when preparing the file for release even if the
server does not implement open. The inode reference will be dropped when
the last reference on the fuse file is dropped (see fuse_file_put() ->
fuse_release_end()).
Fixes: e26ee4efbc ("fuse: allocate ff->release_args only if release is needed")
Cc: stable@vger.kernel.org
Signed-off-by: Joanne Koong <joannelkoong@gmail.com>
Reported-by: Omar Sandoval <osandov@fb.com>
Signed-off-by: Miklos Szeredi <mszeredi@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 95c39eef7c upstream.
When a request is terminated before it has been committed, the request
is not removed from the queue's list. This leaves a dangling list entry
that leads to list corruption and use-after-free issues.
Remove the request from the queue's list for terminated non-committed
requests.
Signed-off-by: Joanne Koong <joannelkoong@gmail.com>
Fixes: c090c8abae ("fuse: Add io-uring sqe commit and fetch support")
Cc: stable@vger.kernel.org
Reviewed-by: Bernd Schubert <bschubert@ddn.com>
Signed-off-by: Miklos Szeredi <mszeredi@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit de83d4617f upstream.
The driver is dropping the references taken to the larb devices during
probe after successful lookup as well as on errors. This can
potentially lead to a use-after-free in case a larb device has not yet
been bound to its driver so that the iommu driver probe defers.
Fix this by keeping the references as expected while the iommu driver is
bound.
Fixes: 2659392856 ("iommu/mediatek: Add error path for loop of mm_dts_parse")
Cc: stable@vger.kernel.org
Cc: Yong Wu <yong.wu@mediatek.com>
Acked-by: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Reviewed-by: Yong Wu <yong.wu@mediatek.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit bba4322e3f upstream.
Modify disk_update_zone_resources() to freeze the device queue before
updating the number of zones, zone capacity and other zone related
resources. The locking order resulting from the call to
queue_limits_commit_update_frozen() is preserved, that is, the queue
limits lock is first taken by calling queue_limits_start_update() before
freezing the queue, and the queue is unfrozen after executing
queue_limits_commit_update(), which replaces the call to
queue_limits_commit_update_frozen().
This change ensures that there are no in-flights I/Os when the zone
resources are updated due to a zone revalidation. In case of error when
the limits are applied, directly call disk_free_zone_resources() from
disk_update_zone_resources() while the disk queue is still frozen to
avoid needing to freeze & unfreeze the queue again in
blk_revalidate_disk_zones(), thus simplifying that function code a
little.
Fixes: 0b83c86b44 ("block: Prevent potential deadlock in blk_revalidate_disk_zones()")
Cc: stable@vger.kernel.org
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Reviewed-by: Chaitanya Kulkarni <kch@nvidia.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5654889a94 upstream.
On some flexcom nodes related to uart, the fifo sizes were wrong: fix
them to 32 data.
Fixes: 7540629e2f ("ARM: dts: at91: add sama7g5 SoC DT and sama7g5-ek")
Cc: stable@vger.kernel.org # 5.15+
Signed-off-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Link: https://lore.kernel.org/r/20251114103313.20220-2-nicolas.ferre@microchip.com
Signed-off-by: Claudiu Beznea <claudiu.beznea@tuxon.dev>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1f591be0a0 upstream.
On some flexcom nodes related to uart, the fifo sizes were wrong: fix
them to 32 data. Note that product datasheet is being reviewed to fix
inconsistency, but this value is validated by product's designers.
Fixes: 261dcfad1b ("ARM: dts: microchip: add sama7d65 SoC DT")
Fixes: b51e4aea3e ("ARM: dts: microchip: sama7d65: Add FLEXCOMs to sama7d65 SoC")
Cc: stable@vger.kernel.org # 6.16+
Signed-off-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Link: https://lore.kernel.org/r/20251114103313.20220-1-nicolas.ferre@microchip.com
Signed-off-by: Claudiu Beznea <claudiu.beznea@tuxon.dev>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 07272e883f upstream.
The macros FAN_FROM_REG and TEMP_FROM_REG evaluate their arguments
multiple times. When used in lockless contexts involving shared driver
data, this causes Time-of-Check to Time-of-Use (TOCTOU) race
conditions.
Convert the macros to static functions. This guarantees that arguments
are evaluated only once (pass-by-value), preventing the race
conditions.
Adhere to the principle of minimal changes by only converting macros
that evaluate arguments multiple times and are used in lockless
contexts.
Link: https://lore.kernel.org/all/CALbr=LYJ_ehtp53HXEVkSpYoub+XYSTU8Rg=o1xxMJ8=5z8B-g@mail.gmail.com/
Fixes: 85f03bccd6 ("hwmon: Add support for Winbond W83L786NG/NR")
Cc: stable@vger.kernel.org
Signed-off-by: Gui-Dong Han <hanguidong02@gmail.com>
Link: https://lore.kernel.org/r/20251128123816.3670-1-hanguidong02@gmail.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 670d7ef945 upstream.
The macro FAN_FROM_REG evaluates its arguments multiple times. When used
in lockless contexts involving shared driver data, this leads to
Time-of-Check to Time-of-Use (TOCTOU) race conditions, potentially
causing divide-by-zero errors.
Convert the macro to a static function. This guarantees that arguments
are evaluated only once (pass-by-value), preventing the race
conditions.
Additionally, in store_fan_div, move the calculation of the minimum
limit inside the update lock. This ensures that the read-modify-write
sequence operates on consistent data.
Adhere to the principle of minimal changes by only converting macros
that evaluate arguments multiple times and are used in lockless
contexts.
Link: https://lore.kernel.org/all/CALbr=LYJ_ehtp53HXEVkSpYoub+XYSTU8Rg=o1xxMJ8=5z8B-g@mail.gmail.com/
Fixes: 9873964d6e ("[PATCH] HWMON: w83791d: New hardware monitoring driver for the Winbond W83791D")
Cc: stable@vger.kernel.org
Signed-off-by: Gui-Dong Han <hanguidong02@gmail.com>
Link: https://lore.kernel.org/r/20251202180105.12842-1-hanguidong02@gmail.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 02f0ad8e8d upstream.
The i2c regmap allocated during probe is never freed.
Switch to using the device managed allocator so that the regmap is
released on probe failures (e.g. probe deferral) and on driver unbind.
Fixes: 3a2a8cc3fe ("hwmon: (max6697) Convert to use regmap")
Cc: stable@vger.kernel.org # 6.12
Cc: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Johan Hovold <johan@kernel.org>
Link: https://lore.kernel.org/r/20251127134351.1585-1-johan@kernel.org
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b8d5acdcf5 upstream.
In max16065_current_show, data->curr_sense is read twice: once for the
error check and again for the calculation. Since
i2c_smbus_read_byte_data returns negative error codes on failure, if the
data changes to an error code between the check and the use, ADC_TO_CURR
results in an incorrect calculation.
Read data->curr_sense into a local variable to ensure consistency. Note
that data->curr_gain is constant and safe to access directly.
This aligns max16065_current_show with max16065_input_show, which
already uses a local variable for the same reason.
Link: https://lore.kernel.org/all/CALbr=LYJ_ehtp53HXEVkSpYoub+XYSTU8Rg=o1xxMJ8=5z8B-g@mail.gmail.com/
Fixes: f5bae2642e ("hwmon: Driver for MAX16065 System Manager and compatibles")
Cc: stable@vger.kernel.org
Signed-off-by: Gui-Dong Han <hanguidong02@gmail.com>
Link: https://lore.kernel.org/r/20251128124709.3876-1-hanguidong02@gmail.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 525916ce49 upstream.
When cloning with node replacements (IORING_REGISTER_DST_REPLACE),
destination entries after the cloned range are not copied over.
Add logic to copy them over to the new destination table.
Fixes: c1329532d5 ("io_uring/rsrc: allow cloning with node replacements")
Cc: stable@vger.kernel.org
Signed-off-by: Joanne Koong <joannelkoong@gmail.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
