Revert changes in definitions that were submitted on May 11 2011 and
committed on June 7 2011. No reason for the change in these values was
given in the patch comment, it broke compatibility with older
versions, and was difficult to detect by the simultaneous move of the
lines of code.
Signed-off-by: Alexander Thomas <alexander.thomas@esaturnus.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
1. add different clkmux mode handling
SAIF can use two instances to implement full duplex (playback &
recording) and record saif may work on EXTMASTER mode which is
using other saif's BITCLK&LRCLK.
The clkmux mode could be set in pdata->init() in mach-specific code.
For generic saif driver, it only needs to know who is his master
and the master id is also provided in mach-specific code.
2. support playback and capture simutaneously however the sample
rates can not be different due to hw limitation.
Signed-off-by: Dong Aisheng <b29396@freescale.com>
Acked-by: Wolfram Sang <w.sang@pengutronix.de>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Vinod Koul <vinod.koul@linux.intel.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The WM8996 can measure the impedance of accessories connected to the
headphone output. Implement initial support for this, measuring the
left channel impedance when an accessory is detected and using this
to distinguish between a line load and a headphone load.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Rather than managing the bandgap in the bias level control use a supply
widget as we only actually need to enable it for analogue paths, not
fully digital ones.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>
The registers are slightly different between v1 and v2 ip that
is available in omap4 and later for some timers.
Add support for v2 ip by mapping the interrupt related registers
separately and adding func_base for the functional registers.
Also disable dmtimer driver features on omap4 for now as
those need the hwmod conversion series to deal with enabling
the timers properly in omap_dm_timer_init.
Signed-off-by: Afzal Mohammed <afzal@ti.com>
Tested-by: Hemant Pedanekar <hemantp@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
When debugging tight race conditions, it can be helpful to have a
synchronized tracing method. Although in most cases the global clock
provides this functionality, if timings is not the issue, it is more
comforting to know that the order of events really happened in a precise
order.
Instead of using a clock, add a "counter" that is simply an incrementing
atomic 64bit counter that orders the events as they are perceived to
happen.
The trace_clock_counter() is added from the attempt by Peter Zijlstra
trying to convert the trace_clock_global() to it. I took Peter's counter
code and made trace_clock_counter() instead, and added it to the choice
of clocks. Just echo counter > /debug/tracing/trace_clock to activate
it.
Requested-by: Thomas Gleixner <tglx@linutronix.de>
Requested-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Reviewed-By: Valdis Kletnieks <valdis.kletnieks@vt.edu>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux:
drm/radeon/kms: Make GPU/CPU page size handling consistent in blit code (v2)
drm/radeon/kms: fix typo in r100_blit_copy
drm/radeon: Unreference GEM object outside of spinlock in page flip error path.
drm/radeon: Don't read from CP ring write pointer registers.
drm/ttm: request zeroed system memory pages for new TT buffer objects
Look up closed stateid's in the stateid hash like any other stateid
rather than searching the close lru.
This is simpler, and fixes a bug: currently we handle only the case of a
close that is the last close for a given stateowner, but not the case of
a close for a stateowner that still has active opens on other files.
Thus in a case like:
open(owner, file1)
open(owner, file2)
close(owner, file2)
close(owner, file2)
the final close won't be recognized as a retransmission.
Signed-off-by: J. Bruce Fields <bfields@redhat.com>
Including the full clientid in the on-the-wire stateid allows more
reliable detection of bad vs. expired stateid's, simplifies code, and
ensures we won't reuse the opaque part of the stateid (as we currently
do when the same openowner closes and reopens the same file).
Signed-off-by: J. Bruce Fields <bfields@redhat.com>
In pl08x_free_txd(), check if pool is allocated successfully before freeing it.
Signed-off-by: Viresh Kumar <viresh.kumar@st.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Untill now, sg_len greater than one is not supported. This patch adds support to
do that.
Note: Still, if peripheral is flow controller, sg_len can't be greater that one.
Signed-off-by: Viresh Kumar <viresh.kumar@st.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
When the system has only the headphone and the line-out jacks without
speakers, the current auto-mute code doesn't work. It's because the
spec->automute_lines flag is wrongly referred in update_speakers().
This flag must be meaningless when spec->automute_hp_lo isn't set, thus
they should be always coupled.
The patch fixes the problem and add a comment to indicate the
relationship briefly.
BugLink: http://bugs.launchpad.net/bugs/851697
Reported-by: David Henningsson <david.henningsson@canonical.com>
Tested-By: Jayne Han <jayne.han@canonical.com>
Cc: stable@kernel.org (3.0)
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Some boards based on S3C6410 use synchronous clocking, which means that HCLKx2
and other system clocks are generated from APLL instead of MPLL.
This patch adds support for such boards, by calculating hclk2 depending on
the status of S3C_OTHERS_SYNCMUXSEL bit in S3C64XX_OTHERS regist
Signed-off-by: Tomasz Figa <tomasz.figa@gmail.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch makes sure that the LCD bypass state is preserved during sleep mode.
It achieves this by saving the S3C64XX_MODEM_MIFPCON register, which is not
handled by any other code currently.
Signed-off-by: Tomasz Figa <tomasz.figa@gmail.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch makes sure that S3C64XX_SDMA_SEL register is preserved during
sleep mode, as it is critical for DMA operation and the DMA driver alone
does not provide any power management facilities.
Signed-off-by: Tomasz Figa <tomasz.figa@gmail.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch adds a definition of S3C64XX_SDMA_SEL register and modifies
the s3c64xx DMA driver to use it instead of a magic register address.
Signed-off-by: Tomasz Figa <tomasz.figa@gmail.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
The Lowland system is a combination of the Cragganmore CPU module and the
Tomatin and Kilchomin audio modules on Glenfarclas.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
The Kilchoman audio module carries a WM5100 audio CODEC and WM9081 speaker
amplifier.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
The Cragganmore system is modular with I2C based identification chips on
the system allowing identification of the system build. Provide a stub I2C
driver which parses the module IDs and uses them to select the appropriate
audio subsystem components to register. To avoid confusion due to having
the mini-driver in the system the driver is placed in a separate file.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Configuration of the WEP keys needs to be delayed until the AP mode has
been properly started at the target. Partial support for delaying the
WEP key configuration was already in place in the driver, but the actual
part of deciding when to do this was missing.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
On some sh-mobile systems there are more than one DMA controllers, that
can be used for serial ports. Specifying a DMA device in sh-sci platform
data unnecessarily restricts the driver to only use one DMA controller.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
[Fixed the trivial conflict in include/linux/serial_sci.h]
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
D-SACK is allowed to reside below snd_una. But the corresponding check
in tcp_is_sackblock_valid() is the exact opposite. It looks like a typo.
Signed-off-by: Zheng Yan <zheng.z.yan@intel.com>
Acked-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
commit 946cedccbd (tcp: Change possible SYN flooding messages)
added a build error if CONFIG_SYN_COOKIES=n
Reported-by: Markus Trippelsdorf <markus@trippelsdorf.de>
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Platform data is provided for two instance of pl330 DMAC,
but only one DMAC is register with amba_device.
This patch register the second instance.
Signed-off-by: Alim Akhtar <alim.akhtar@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Platform data is provided for two instance of pl330 DMAC,
but only one DMAC is register with amba_device.
This patch register the second instance.
Signed-off-by: Alim Akhtar <alim.akhtar@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Platform data is provided for two instance of pl330 DMAC,
but only one DMAC is register with amba_device.
This patch register the second instance.
Signed-off-by: Alim Akhtar <alim.akhtar@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
* 'for-linus' of git://git.infradead.org/users/sameo/mfd-2.6:
mfd: Fix omap-usb-host build failure
mfd: Make omap-usb-host TLL mode work again
mfd: Set MAX8997 irq pointer
mfd: Fix initialisation of tps65910 interrupts
mfd: Check for twl4030-madc NULL pointer
mfd: Copy the device pointer to the twl4030-madc structure
mfd: Rename wm8350 static gpio_set_debounce()
mfd: Fix value of WM8994_CONFIGURE_GPIO
I got an opinion that it is difficult to use exception policy's domain
transition control directives because they need to match the pathname specified
to "file execute" directives. For example, if "file execute /bin/\*\-ls\-cat"
is given, corresponding domain transition control directive needs to be like
"no_keep_domain /bin/\*\-ls\-cat from any".
If we can specify like below, it will become more convenient.
file execute /bin/ls keep exec.realpath="/bin/ls" exec.argv[0]="ls"
file execute /bin/cat keep exec.realpath="/bin/cat" exec.argv[0]="cat"
file execute /bin/\*\-ls\-cat child
file execute /usr/sbin/httpd <apache> exec.realpath="/usr/sbin/httpd" exec.argv[0]="/usr/sbin/httpd"
In above examples, "keep" works as if keep_domain is specified, "child" works
as if "no_reset_domain" and "no_initialize_domain" and "no_keep_domain" are
specified, "<apache>" causes domain transition to <apache> domain upon
successful execve() operation.
Moreover, we can also allow transition to different domains based on conditions
like below example.
<kernel> /usr/sbin/sshd
file execute /bin/bash <kernel> /usr/sbin/sshd //batch-session exec.argc=2 exec.argv[1]="-c"
file execute /bin/bash <kernel> /usr/sbin/sshd //root-session task.uid=0
file execute /bin/bash <kernel> /usr/sbin/sshd //nonroot-session task.uid!=0
Signed-off-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Signed-off-by: James Morris <jmorris@namei.org>
If there was ever any code that used MEM_ALLOC_THRESHOLD, it was removed a
long time ago.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
The video buffer is not uncached memory-mapped I/O, so don't tag the virtual
address as __iomem. It's also not a u8*.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Uninstalling the framebuffers in reverse order is unnecessary and makes
the for-loop awkward.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
We were forgetting to unmap the video memory if fsl_diu_check_var() fails.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
It makes no sense to limit the size of a strncpy() to the length of
the source string.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Use the name "fsl-diu-fb" in the Freescale DIU framebuffer driver
during registrations.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Clean up the local variable usage in request_irq_local() and allocate_buf().
This streamlines the code without affecting functionality.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
The framebuffer layer already uses the first video mode defined in the
fb_videomode array as a default, so there's no need to duplicate the
first entry into a stand-alone structure.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Implement various improvements to the way the Freescale DIU framebuffer
driver access the device tree.
1) Use of_iomap() instead of of_address_to_resource() and ioremap()
2) Use be32_to_cpup() instead of directly dereferencing the device_node
pointer.
3) Rename variable 'ofdev' to 'pdev' to avoid any confusion that it's
a platform_device pointer, not an of_device pointer (of_device no
longer exists).
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Fix this compilation warning in the Freescale DIU framebuffer driver:
warning: 'dummy_ad_addr' may be used uninitialized in this function
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Remove some unused ioctl commands, and treat those commands as unsupported
instead of ignored.
Also remove struct mfb_alpha, which isn't used by any ioctl. It may have
been once intended for MFB_SET_ALPHA, but that ioctl uses a different
data structure.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>