Commit graph

286,663 commits

Author SHA1 Message Date
Allan Stephens
b4b5610223 tipc: Ensure both nodes recognize loss of contact between them
Enhances TIPC to ensure that a node that loses contact with a
neighboring node does not allow contact to be re-established until
it sees that its peer has also recognized the loss of contact.

Previously, nodes that were connected by two or more links could
encounter a situation in which node A would lose contact with node B
on all of its links, purge its name table of names published by B,
and then fail to repopulate those names once contact with B was restored.
This would happen because B was able to re-establish one or more links
so quickly that it never reached a point where it had no links to A --
meaning that B never saw a loss of contact with A, and consequently
didn't re-publish its names to A.

This problem is now prevented by enhancing the cleanup done by TIPC
following a loss of contact with a neighboring node to ensure that
node A ignores all messages sent by B until it receives a LINK_PROTOCOL
message that indicates B has lost contact with A, thereby preventing
the (re)establishment of links between the nodes. The loss of contact
is recognized when a RESET or ACTIVATE message is received that has
a "redundant link exists" field of 0, indicating that B's sending link
endpoint is in a reset state and that B has no other working links.

Additionally, TIPC now suppresses the sending of (most) link protocol
messages to a neighboring node while it is cleaning up after an earlier
loss of contact with that node. This stops the peer node from prematurely
activating its link endpoint, which would prevent TIPC from later
activating its own end. TIPC still allows outgoing RESET messages to
occur during cleanup, to avoid problems if its own node recognizes
the loss of contact first and tries to notify the peer of the situation.

Finally, TIPC now recognizes an impending loss of contact with a peer node
as soon as it receives a RESET message on a working link that is the
peer's only link to the node, and ensures that the link protocol
suppression mentioned above goes into effect right away -- that is,
even before its own link endpoints have failed. This is necessary to
ensure correct operation when there are redundant links between the nodes,
since otherwise TIPC would send an ACTIVATE message upon receiving a RESET
on its first link and only begin suppressing when a RESET on its second
link was received, instead of initiating suppression with the first RESET
message as it needs to.

Note: The reworked cleanup code also eliminates a check that prevented
a link endpoint's discovery object from responding to incoming messages
while stale name table entries are being purged. This check is now
unnecessary and would have slowed down re-establishment of communication
between the nodes in some situations.

Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
2011-09-17 22:55:03 -04:00
Linus Torvalds
01a7143586 Merge branch 'fixes' of git://git.user.in-berlin.de/s5r6/linux1394
* 'fixes' of git://git.user.in-berlin.de/s5r6/linux1394:
  firewire: ohci: add no MSI quirk for O2Micro controller
2011-09-17 16:54:41 -07:00
Linus Torvalds
4be0ed42c5 Merge branch '3.1-rc-fixes' of git://linux-iscsi.org/target-pending
* '3.1-rc-fixes' of git://linux-iscsi.org/target-pending:
  iscsi-target: Fix sendpage breakage with proper padding+DataDigest iovec offsets
  iscsi-target: Disable markers + remove dangerous local scope array usage
  target: Skip non hex characters for VPD=0x83 NAA IEEE Registered Extended
  tcm_fc: Work queue based approach instead of managing own thread and event based mechanism
  tcm_fc: Invalidation of DDP context for FCoE target in error conditions
  target: Fix race between multiple invocations of target_qf_do_work()
2011-09-17 16:52:13 -07:00
Jurgen Kramer
f78b68261e Bluetooth: add support for 2011 mac mini
Today I noticed that the usb bluetooth adapter (BCM2046B1) on my 2011
mac mini was not working. I've created a patch to get it going.

Signed-off-by: Jurgen Kramer <gtmkramer@xs4all.nl>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
2011-09-17 17:16:03 -03:00
Pieter-Augustijn Van Malleghem
a63b723d02 Bluetooth: Add MacBookAir4,1 support
This patch against current git adds the hardware ID for the Apple
MacBookAir4,1, released in July 2011. The device features a BCM2046
USB chip. The patch was inspired by the previous modifications adding
support for the MacBookAir3,x.

Signed-off-by: Pieter-Augustijn Van Malleghem <p-a@scarlet.be>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
2011-09-17 17:15:32 -03:00
Chen Ganir
8be964d236 Bluetooth: Fixed BT ST Channel reg order
Reordered the BT ST channel registration, to make sure that the
event channel is registered before all others. This prevents a
situation where incoming events may cause kernel panic in the ST
driver if the event channel is not yet registered to handle
incoming events.In addition, the deregistration of the channels
was also modified, to be in the reversed order of the registration,
to allow the event channel to be the last one unregistered.

Signed-off-by: Chen Ganir <chen.ganir@ti.com>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
2011-09-17 17:15:25 -03:00
Bhanu Prakash Gollapudi
cf00025d1d [SCSI] bnx2fc: Bumped version to 1.0.6
Signed-off-by: Bhanu Prakash Gollapudi <bprakash@broadcom.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
2011-09-17 23:10:21 +04:00
Bhanu Prakash Gollapudi
a96e8e1163 [SCSI] bnx2fc: Fix FW assert during RSCN stress tests
Firmware asserts when the same CQE is armed twice. This scenario happens during
RSCN stress tests as driver incorrects arms the CQ after the session is
offloaded.

Signed-off-by: Bhanu Prakash Gollapudi <bprakash@broadcom.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
2011-09-17 23:10:00 +04:00
J. Bruce Fields
2da1cec713 nfsd4: simplify free_stateid
We no longer need is_deleg_stateid, for example.

Signed-off-by: J. Bruce Fields <bfields@redhat.com>
2011-09-17 10:31:16 -04:00
Bhanu Prakash Gollapudi
013068fa6f [SCSI] bnx2fc: Fix panic caused because of incorrect errror handling in create().
Driver incorrectly calls bnx2fc_interface_cleanup() when bnx2fc_if_create fails
which accesses bad pointer. Handle bnx2fc_if_create failure by directly calling
bnx2fc_net_cleanup.

Signed-off-by: Bhanu Prakash Gollapudi <bprakash@broadcom.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
2011-09-17 18:05:33 +04:00
Bhanu Prakash Gollapudi
0cbf32e168 [SCSI] bnx2fc: Avoid calling bnx2fc_if_destroy with unnecessary locks
It is not required to hold rtnl_lock and bnx2fc_dev_lock when calling
bnx2fc_if_destroy, as the locking is only required to serialize creation and
deletion of fcoe instances. More importantly, this unnecessary locking causes
deadlock as bnx2fc_if_destroy calls fc_remove_host holding rtnl_lock.

Signed-off-by: Bhanu Prakash Gollapudi <bprakash@broadcom.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
2011-09-17 18:04:25 +04:00
Nithin Nayak Sujir
26b2982f78 [SCSI] bnx2fc: Validate vlan id in NETDEV_UNREGISTER handler
When bnx2fc receives an UNREGISTER event on a vlan interface it calls
destroy on all interfaces that matches the physical interface. Add
vlan_id check to destroy only the vlan interface that generated the
event.

Signed-off-by: Nithin Nayak Sujir <nsujir@broadcom.com>
Signed-off-by: Bhanu Prakash Gollapudi <bprakash@broadcom.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
2011-09-17 18:03:18 +04:00
Bhanu Prakash Gollapudi
c1c16bd51a [SCSI] bnx2fc: No abort issued for REC when it times out
ABTS was not issued for timed out REC, as REC completion handler exits out if
the IO completed. Check for timed out REC and issue ABTS before proceeding with
further processing in REC completion handler. Also, initialize rec_retry and
srr_retry before starting the IO.

Signed-off-by: Bhanu Prakash Gollapudi <bprakash@broadcom.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
2011-09-17 18:02:27 +04:00
Bhanu Prakash Gollapudi
8a5badf1ea [SCSI] bnx2fc: Send solicitation only after vlan discovery is complete
Link up event is generated to the driver even before vlan discovery has
started. Because of this driver can send discovery solicitation on a stale
vlan. Call fcoe_ctlr_link_up() only when the driver is in enabled state, which
implies the vlan discovery is complete before sending solicitation.

Signed-off-by: Bhanu Prakash Gollapudi <bprakash@broadcom.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
2011-09-17 18:01:58 +04:00
J. Bruce Fields
38c387b52d nfsd4: match close replays on stateid, not open owner id
Keep around an unhashed copy of the final stateid after the last close
using an openowner, and when identifying a replay, match against that
stateid instead of just against the open owner id.  Free it the next
time the seqid is bumped or the stateowner is destroyed.

Signed-off-by: J. Bruce Fields <bfields@redhat.com>
2011-09-17 10:01:54 -04:00
Bhanu Prakash Gollapudi
c780673cfb [SCSI] bnx2fc: Reset max receive frame size during link up
If the max receive frame size is changed during link down, the driver uses the
same value after linkup unless it is reset to default.

Signed-off-by: Bhanu Prakash Gollapudi <bprakash@broadcom.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
2011-09-17 17:57:52 +04:00
Mauro Carvalho Chehab
7577911244 Merge tag 'v3.1-rc6' into staging/for_v3.2
* tag 'v3.1-rc6': (1902 commits)
  Linux 3.1-rc6
  ioctl: register LTTng ioctl
  fuse: fix memory leak
  fuse: fix flock breakage
  Btrfs: add dummy extent if dst offset excceeds file end in
  Btrfs: calc file extent num_bytes correctly in file clone
  btrfs: xattr: fix attribute removal
  Btrfs: fix wrong nbytes information of the inode
  Btrfs: fix the file extent gap when doing direct IO
  Btrfs: fix unclosed transaction handle in btrfs_cont_expand
  Btrfs: fix misuse of trans block rsv
  Btrfs: reset to appropriate block rsv after orphan operations
  Btrfs: skip locking if searching the commit root in csum lookup
  btrfs: fix warning in iput for bad-inode
  Btrfs: fix an oops when deleting snapshots
  [media] vp7045: fix buffer setup
  [media] nuvoton-cir: simplify raw IR sample handling
  [media] [Resend] viacam: Don't explode if pci_find_bus() returns NULL
  [media] v4l2: Fix documentation of the codec device controls
  [media] gspca - sonixj: Fix the darkness of sensor om6802 in 320x240
  ...
2011-09-17 10:29:49 -03:00
Russell King
4dfa33868d ARM: nommu: fix warning with checksyscalls.sh
CALL    scripts/checksyscalls.sh
<stdin>:46:1: warning: "__IGNORE_migrate_pages" redefined
In file included from <stdin>:2:
arch/arm/include/asm/unistd.h:482:1: warning: this is the location of the previous definition

This is caused because we define __IGNORE_migrate_pages to be 1, but
in the case of nommu, it's defined to be empty.  Fix this by just
defining the __IGNORE_ symbols to be empty.

Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2011-09-17 12:50:57 +01:00
Will Deacon
f630c1bdfb ARM: 7091/1: errata: D-cache line maintenance operation by MVA may not succeed
This patch implements a workaround for erratum 764369 affecting
Cortex-A9 MPCore with two or more processors (all current revisions).
Under certain timing circumstances, a data cache line maintenance
operation by MVA targeting an Inner Shareable memory region may fail to
proceed up to either the Point of Coherency or to the Point of
Unification of the system. This workaround adds a DSB instruction before
the relevant cache maintenance functions and sets a specific bit in the
diagnostic control register of the SCU.

Cc: <stable@kernel.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Tested-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2011-09-17 12:47:17 +01:00
Thomas Meyer
902532dbe8 ARM: davinci: edma: use kzalloc()
Use kzalloc rather than kmalloc followed by memset with 0

 This considers some simple cases that are common and easy to validate
 Note in particular that there are no ...s in the rule, so all of the
 matched code has to be contiguous

 The semantic patch that makes this output is available
 in scripts/coccinelle/api/alloc/kzalloc-simple.cocci.

 More information about semantic patching is available at
 http://coccinelle.lip6.fr/

Signed-off-by: Thomas Meyer <thomas@m3y3r.de>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
2011-09-17 15:54:09 +05:30
Ido Yariv
f23fe857bb ARM: davinci: Explicitly set channel controllers' default queues
Davinci platforms may define a default queue for each channel
controller. If one is not defined, the default queue is set to EVENTQ_1.
However, there's no way to distinguish between an unset default queue to
one that is set to EVENTQ_0, as EVENTQ_0 = 0.

Explicitly specify the default queue for all channel controllers on all
Davinci platforms to EVENTQ_1, and don't overwrite it in the EDMA probe
function.

One exception is the DA850 board, for which EVENTQ_1 is not a valid
option for its second channel controller. Use EVENTQ_0 instead for that
channel controller.

Signed-off-by: Ido Yariv <ido@wizery.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
2011-09-17 15:54:08 +05:30
Ido Yariv
ab3f5c1fc2 ARM: davinci: AM18x: Add wl1271/wlan support
The wl1271 daughter card for AM18x EVMs is a combo wireless connectivity
add-on card, based on the LS Research TiWi module with Texas
Instruments' wl1271 solution.
It is a 4-wire, 1.8V, embedded SDIO WLAN device with an external IRQ
line and is power-controlled by a GPIO-based fixed regulator.

Add support for the WLAN capabilities of this expansion board.

Signed-off-by: Ido Yariv <ido@wizery.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
2011-09-17 15:53:23 +05:30
Ido Yariv
4a9de8ad2c mmc: davinci: Add support for set_power callback
Some devices connected to the MMC bus are power controlled by external
means. For instance, an SDIO device may be powered down/up by an
external gpio line.

In order to avoid toggling power from within the MMC host driver, add a
set_power callback function, which will be called by set_ios upon
powering down/up.

Signed-off-by: Ido Yariv <ido@wizery.com>
CC: Chris Ball <cjb@laptop.org>
Acked-by: Chris Ball <cjb@laptop.org>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
2011-09-17 15:53:23 +05:30
Ido Yariv
6836989c35 ARM: davinci: DA850: Add GPIO pinmux configuration for wl1271
The wl1271 daughter board makes use of a few GPIOs:
GPIO6_9 is used for powering down/up the WLAN functionality.
GPIO6_10 is used as an input IRQ line from the WLAN chip.

Add the required pinmux configuration for these GPIOs.

Signed-off-by: Ido Yariv <ido@wizery.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
2011-09-17 15:53:22 +05:30
Ido Yariv
5c4d11b477 ARM: davinci: DA850: Add MMC/SD1 pinmux configuration
AM18x has two MMC slots. Add the required pinmux configuration for the
second slot.

Signed-off-by: Ido Yariv <ido@wizery.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
2011-09-17 15:53:22 +05:30
Francois Romieu
2544bfc0eb r8169: do not enable the TBI for anything but the original 8169.
The TBI bit in PHYStatus is reserved on anything but the oldest 8169.

Nobody complained after I disabled it for the 8168 and the 810x (see
66ec5d4fb1).

Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Cc: Hayes Wang <hayeswang@realtek.com>
2011-09-17 11:42:21 +02:00
Francois Romieu
e03f33af79 r8169: remove erroneous processing of always set bit.
When set, RxFOVF (resp. RxBOVF) is always 1 (resp. 0).

Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Cc: Hayes <hayeswang@realtek.com>
2011-09-17 11:38:05 +02:00
Hayes Wang
106633897e r8169: fix WOL setting for 8105 and 8111evl
rtl8105, rtl8111E, and rtl8111evl need enable RxConfig bit 1 ~ 3
for supporting wake on lan.

Signed-off-by: Hayes Wang <hayeswang@realtek.com>
2011-09-17 11:37:48 +02:00
Hayes Wang
bbb8af75d0 r8169: add MODULE_FIRMWARE for the firmware of 8111evl
Add MODULE_FIRMWARE for the firmware of RTL8111E-VL

Signed-off-by: Hayes Wang <hayeswang@realtek.com>
2011-09-17 11:37:34 +02:00
Hayes Wang
c2b0c1e7fb r8169: fix the reset setting for 8111evl
rtl8111evl should stop any TLP requirement before resetting by
enabling register 0x37 bit 7.

Signed-off-by: Hayes Wang <hayeswang@realtek.com>
2011-09-17 11:36:03 +02:00
Eric Dumazet
765cf9976e tcp: md5: remove one indirection level in tcp_md5sig_pool
tcp_md5sig_pool is currently an 'array' (a percpu object) of pointers to
struct tcp_md5sig_pool. Only the pointers are NUMA aware, but objects
themselves are all allocated on a single node.

Remove this extra indirection to get proper percpu memory (NUMA aware)
and make code simpler.

Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2011-09-17 01:15:46 -04:00
Yan, Zheng
8e2ec63917 ipv6: don't use inetpeer to store metrics for routes.
Current IPv6 implementation uses inetpeer to store metrics for
routes. The problem of inetpeer is that it doesn't take subnet
prefix length in to consideration. If two routes have the same
address but different prefix length, they share same inetpeer.
So changing metrics of one route also affects the other. The
fix is to allocate separate metrics storage for each route.

Signed-off-by: Zheng Yan <zheng.z.yan@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2011-09-17 00:57:26 -04:00
Rasesh Mody
b9fa1fbf98 bna: Eliminate Small Race Condition Window in RX Path
Change details:
 - In a continuous sequence of ifconfig up/down operations, there is a small
   window of race between bnad_set_rx_mode() and bnad_cleanup_rx() while the
   former tries to access rx_info->rx & the latter sets it to NULL. This race
   could lead to bna_rx_mode_set() being called with a NULL (rx_info->rx)
   pointer and a crash.
 - Hold bnad->bna_lock while setting / unsetting rx_info->rx in bnad_setup_rx()
   & bnad_cleanup_rx(), thereby eliminating the race described above.

Signed-off-by: Gurunatha Karaje <gkaraje@brocade.com>
Signed-off-by: Rasesh Mody <rmody@brocade.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2011-09-17 00:47:57 -04:00
Rasesh Mody
3fb9852f98 bna: Set Ring Param Fix
When Rx queue size is changed, queues are torn down and setup with the new queue
size. During this operation, clear promiscuous mode and restore the original
VLAN filter.

Signed-off-by: Gurunatha Karaje <gkaraje@brocade.com>
Signed-off-by: Rasesh Mody <rmody@brocade.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2011-09-17 00:47:57 -04:00
Rasesh Mody
1d51a1325e bna: Semaphore Lock Fix
Remove a BUG_ON() as it is not required.

Change the unconditional write to release a semaphore to read sem first
and then write. This will eliminate the possibility of sem getting locked
while trying to release it in case if previous sem_get operation failed.

Signed-off-by: Gurunatha Karaje <gkaraje@brocade.com>
Signed-off-by: Rasesh Mody <rmody@brocade.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2011-09-17 00:47:57 -04:00
Mark Brown
986afc98ce ARM: S3C64XX: Hook up GPIO initiated DVS on Cragganmore
Allow us to ramp VDDARM quickly by using a GPIO to signal a voltage change
instead of doing a register write.

Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
2011-09-17 11:27:50 +09:00
Emil Tantilov
ae0e148934 ixgbe: remove duplicate netif_tx_start_all_queues
netif_tx_start_all_queues() is already called in ixgbe_up_complete, no need
to do it twice.

Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2011-09-16 19:05:52 -07:00
Kukjin Kim
4c59de052e Merge branch 'next/topic-plat-samsung-1' into next-samsung-cleanup 2011-09-17 11:05:43 +09:00
Emil Tantilov
80bb25e3eb ixgbe: fix FCRTL/H register dump for X540
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2011-09-16 19:04:06 -07:00
Emil Tantilov
1a70db4b05 ixgbe: cleanup some register reads
Remove duplicate inc of hwstats->ruc
Introduce separate loops for 8 and 16 register reads.
Consolidate mac checks under one case.
Make sure registers are cleared on read.

Reported-by: Jonathan Lynch <jonathan.lynch@thenowfactory.com>
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
CC: Jonathan Lynch <jonathan.lynch@thenowfactory.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2011-09-16 19:02:37 -07:00
Alexander Duyck
919e78a6b8 ixgbe: Make better use of memory allocations in one-buffer mode w/ RSC
This patch improves the memory utilization with RSC when in one-buffer
mode.  This is accomplished by making the default buffer sizes match up
with the standard memory allocation sizes minus 1K for shared info and
padding overhead.  By doing this CPU utilization when doing large receives
can be reduced by as much as 8%.

Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2011-09-16 19:00:11 -07:00
Alexander Duyck
398fe4a916 ixgbe: drop adapter from ixgbe_fso call documentation
The adapter structure was removed from the call so it can be dropped from
the ixgbe_fso documentation.

Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2011-09-16 18:56:24 -07:00
Alexander Duyck
8917b447b7 ixgbe: Add SFP support for missed 82598 PHY
One of the 82598 phys was not being correctly identified as being SFP.
This change corrects that.

Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2011-09-16 18:54:48 -07:00
Alexander Duyck
5fdd31f920 ixgbe: Add missing code for enabling overheat sensor interrupt
This change adds a small bit of missing code for enabling the overheat sensor

Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2011-09-16 18:45:49 -07:00
Alexander Duyck
c7ccde0f83 ixgbe: make ixgbe_up and ixgbe_up_complete void functions
ixgbe_up and ixgbe_up_complete will always return 0.  Since this doesn't
provide any useful information we might as well just make them both void
and save ourselves from having to return an unused value.

Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2011-09-16 18:39:56 -07:00
Alexander Duyck
f7e1027f61 v2 ixgbe: Update packet buffer reservation to correct fdir headroom size
This change fixes an issue in which the incorrect amount of headroom was
being reserved for flow director filters.

Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2011-09-16 18:39:34 -07:00
Alexander Duyck
4c1d7b4b5d ixgbe: remove redundant configuration of tx_sample_rate
This change fixes a minor redundancy in that tx_sample_rate was set twice.

Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2011-09-16 18:29:29 -07:00
Michał Mirosław
d7ccb8c2f2 ixgb: convert to ndo_fix_features
Private rx_csum flags are now duplicate of netdev->features & NETIF_F_RXCSUM.
Removing this needs deeper surgery.

Things noticed:
 - ixgb has RX csum disabled by default
 - HW VLAN acceleration probably can be toggled, but it's left as is
 - the resets on RX csum offload change can probably be avoided
 - there is A LOT of copy-and-pasted code here

Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2011-09-16 18:26:37 -07:00
Jesper Juhl
d4001e086b MIPS: Remove unneeded version.h includes from arch/mips/
It was pointed out by 'make versioncheck' that some includes of
linux/version.h are not needed in arch/mips/.
This patch removes them.

Signed-off-by: Jesper Juhl <jj@chaosbits.net>
To: LKML <linux-kernel@vger.kernel.org>
Cc: trivial@kernel.org
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/2540/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
2011-09-17 02:40:36 +02:00
Kevin Cernekee
1665010757 MIPS: Trivial style cleanups in mmap.c
Fix checkpatch warnings.  Rename arch_get_unmapped_area_foo() to
arch_get_unmapped_area_common().  Make indentations and spacing more
consistent.  Add <linux/compiler.h> for likely/unlikely.

Signed-off-by: Kevin Cernekee <cernekee@gmail.com>
Cc: Jian Peng <jipeng2005@gmail.com>
Cc: David Daney <ddaney@caviumnetworks.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/2506/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
2011-09-17 02:37:04 +02:00