- Move voltage and tone to DVB-S.
- Add turbo code.
- In DVB-S2 and turbo code sections, refer to DVB-S, as both
are extensions to DVB-S.
- Add modulation to DVB-S2.
Signed-off-by: Andreas Oberritter <obi@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
identify a satellite receiver by its 'delivery_system' instead of
'modulation', which may overlap between different delivery systems.
Signed-off-by: Andreas Oberritter <obi@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The goto needs to be moved after the assignment.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch fixes a second punch hole bug found by xfstests 127.
This bug happens because punch hole needs to flush the pages
of the hole to avoid race conditions. But if the end of the
hole is in the same page as i_size, the buffer heads beyond
i_size need to be unmapped and the page needs to be zeroed
after it is flushed.
To correct this, the new ext4_discard_partial_page_buffers
routine is used to zero and unmap the partial page
beyond i_size if the end of the hole appears in the same
page as i_size.
The code has also been optimized to set the end of the hole
to the page after i_size if the specified hole exceeds i_size,
and the code that flushes the pages has been simplified.
Signed-off-by: Allison Henderson <achender@linux.vnet.ibm.com>
This patch addresses a bug found by xfstests 75, 112, 127
when blocksize = 1k
This bug happens because the punch hole code only zeros
out non block aligned regions of the page. This means that if the
blocks are smaller than a page, then the block aligned regions of
the page inside the hole are left un-zeroed, and their buffer heads
are still mapped. This bug is corrected by using
ext4_discard_partial_page_buffers to properly zero the partial page
at the head and tail of the hole, and unmap the corresponding buffer
heads
This patch also addresses a bug reported by Lukas while working on a
new patch to add discard support for loop devices using punch hole.
The bug happened because of the first and last block number
needed to be cast to a larger data type before calculating the
byte offset, but since now we only need the byte offsets of the
pages, we no longer even need to be calculating the byte offsets
of the blocks. The code to do the block offset calculations is
removed in this patch.
Signed-off-by: Allison Henderson <achender@linux.vnet.ibm.com>
This patch adds two new routines: ext4_discard_partial_page_buffers
and ext4_discard_partial_page_buffers_no_lock.
The ext4_discard_partial_page_buffers routine is a wrapper
function to ext4_discard_partial_page_buffers_no_lock.
The wrapper function locks the page and passes it to
ext4_discard_partial_page_buffers_no_lock.
Calling functions that already have the page locked can call
ext4_discard_partial_page_buffers_no_lock directly.
The ext4_discard_partial_page_buffers_no_lock function
zeros a specified range in a page, and unmaps the
corresponding buffer heads. Only block aligned regions of the
page will have their buffer heads unmapped. Unblock aligned regions
will be mapped if needed so that they can be updated with the
partial zero out. This function is meant to
be used to update a page and its buffer heads to be zeroed
and unmapped when the corresponding blocks have been released
or will be released.
This routine is used in the following scenarios:
* A hole is punched and the non page aligned regions
of the head and tail of the hole need to be discarded
* The file is truncated and the partial page beyond EOF needs
to be discarded
* The end of a hole is in the same page as EOF. After the
page is flushed, the partial page beyond EOF needs to be
discarded.
* A write operation begins or ends inside a hole and the partial
page appearing before or after the write needs to be discarded
* A write operation extends EOF and the partial page beyond EOF
needs to be discarded
This function takes a flag EXT4_DISCARD_PARTIAL_PG_ZERO_UNMAPPED
which is used when a write operation begins or ends in a hole.
When the EXT4_DISCARD_PARTIAL_PG_ZERO_UNMAPPED flag is used, only
buffer heads that are already unmapped will have the corresponding
regions of the page zeroed.
Signed-off-by: Allison Henderson <achender@linux.vnet.ibm.com>
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
Tuners in general convert a high frequency carrier into an Intermediate
Frequency (IF).
Digital tuners like tda18271, xc3028, etc. generally allow changing the IF
frequency, although they generally have recommented settings for the IF.
Analog tuners, have a fixed IF frequency, that depends on the physical
characteristics of some analog components.
For digital tuners, it makes sense to have ways to configure IF,
via the tuner's configuration structure, like what's done inside the
tda18271-fe maps.
The demods need to know what IF is used by the tuner, as it will need
to convert internally from IF into baseband. Currently, the bridge driver
needs to fill a per-demod configuration struct for it, or pass it via
a dvb_attach parameter.
The tda18271 datasheet recommends to use different IF's for different
delivery system types and for different bandwidths.
The DRX-K demod also needs to know the IF frequency in order to work,
just like all other demods. However, as it accepts different delivery
systems (DVB-C and DVB-T), the IF may change if the standard and/or
bandwidth is changed.
So, the usual procedure of passing it via a config struct doesn't work.
One might try to code it as two separate IF frequencies, or even as a
table in function of the delivery system and the bandwidth, but this
will be messy.
So, it is better and simpler to just add a new callback for it and
require the tuners that can be used with MFE frontends like drx-k
to implement a new callback to return the used IF.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Acked-by: Antti Palosaari <crope@iki.fi>
Makes it more straight-forward to follow stack traces if the functions
don't have generic names. Using this as a crutch while trying to better
understand the lockdep warnings I get when loading the em28xx driver.
CC: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The one in-tree videobuf2-dma-sg driver (mmp-camera) has no need for a
kernel-space mapping of the buffers; one suspects that most other drivers
would not either. The videobuf2-dma-sg module does the right thing if
buf->vaddr == NULL - it maps the buffer on demand if somebody needs it. So
let's not map the buffer at allocation time; that will save a little CPU
time and a lot of address space in the vmalloc range.
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
Acked-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
- fepriv->parameters_out isn't protected by events->mtx, so
move the call to fe->ops.get_frontend out of the locked area.
- move the assignment of e->status into the locked area.
- use direct assignment instead of memcpy.
- use mutex_lock instead of mutex_lock_interruptible, because
all code paths protected by this mutex won't block.
Signed-off-by: Andreas Oberritter <obi@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
the first event after an attempt to tune.
Signed-off-by: Andreas Oberritter <obi@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Modify it to use the data given by the user.
Signed-off-by: Andreas Oberritter <obi@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Delete nontrivial initialization that is immediately overwritten by the
result of an allocation function.
The semantic match that makes this change is as follows:
// <smpl>
@@
type T;
identifier i;
expression e;
@@
(
T i = \(0\|NULL\|ERR_PTR(...)\);
|
-T i = e;
+T i;
)
... when != i
i = \(kzalloc\|kcalloc\|kmalloc\)(...);
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Acked-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
I don't see the point of having this check in nfs4_preprocess_seqid_op()
when it's only needed by the one caller.
Signed-off-by: J. Bruce Fields <bfields@redhat.com>
bdi_forker_thread() clears BDI_pending bit at the end of the main loop.
However clearing of this bit must not be done in some cases which is
handled by calling 'continue' from switch statement. That's kind of
unusual construct and without a good reason so change the function into
more intuitive code flow.
CC: Wu Fengguang <fengguang.wu@intel.com>
CC: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jan Kara <jack@suse.cz>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
Following on Herton's patch "fb: avoid possible deadlock caused by
fb_set_suspend" which moves lock_fb_info() out of fb_set_suspend()
to its callers, correct sh-mobile's locking around call to
fb_set_suspend() and the same sort of deaklocks with console_lock()
due to order of taking the lock.
console_lock() must be taken while fb_info is already locked and fb_info
must be locked while calling fb_set_suspend().
Signed-off-by: Bruno Prémont <bonbons@linux-vserver.org>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Cc: stable@kernel.org
A lock ordering issue can cause deadlocks: in framebuffer/console code,
all needed struct fb_info locks are taken before acquire_console_sem(),
in places which need to take console semaphore.
But fb_set_suspend is always called with console semaphore held, and
inside it we call lock_fb_info which gets the fb_info lock, inverse
locking order of what the rest of the code does. This causes a real
deadlock issue, when we write to state fb sysfs attribute (which calls
fb_set_suspend) while a framebuffer is being unregistered by
remove_conflicting_framebuffers, as can be shown by following show
blocked state trace on a test program which loads i915 and runs another
forked processes writing to state attribute:
Test process with semaphore held and trying to get fb_info lock:
..
fb-test2 D 0000000000000000 0 237 228 0x00000000
ffff8800774f3d68 0000000000000082 00000000000135c0 00000000000135c0
ffff880000000000 ffff8800774f3fd8 ffff8800774f3fd8 ffff880076ee4530
00000000000135c0 ffff8800774f3fd8 ffff8800774f2000 00000000000135c0
Call Trace:
[<ffffffff8141287a>] __mutex_lock_slowpath+0x11a/0x1e0
[<ffffffff814142f2>] ? _raw_spin_lock_irq+0x22/0x40
[<ffffffff814123d3>] mutex_lock+0x23/0x50
[<ffffffff8125dfc5>] lock_fb_info+0x25/0x60
[<ffffffff8125e3f0>] fb_set_suspend+0x20/0x80
[<ffffffff81263e2f>] store_fbstate+0x4f/0x70
[<ffffffff812e7f70>] dev_attr_store+0x20/0x30
[<ffffffff811c46b4>] sysfs_write_file+0xd4/0x160
[<ffffffff81155a26>] vfs_write+0xc6/0x190
[<ffffffff81155d51>] sys_write+0x51/0x90
[<ffffffff8100c012>] system_call_fastpath+0x16/0x1b
..
modprobe process stalled because has the fb_info lock (got inside
unregister_framebuffer) but waiting for the semaphore held by the
test process which is waiting to get the fb_info lock:
..
modprobe D 0000000000000000 0 230 218 0x00000000
ffff880077a4d618 0000000000000082 0000000000000001 0000000000000001
ffff880000000000 ffff880077a4dfd8 ffff880077a4dfd8 ffff8800775a2e20
00000000000135c0 ffff880077a4dfd8 ffff880077a4c000 00000000000135c0
Call Trace:
[<ffffffff81411fe5>] schedule_timeout+0x215/0x310
[<ffffffff81058051>] ? get_parent_ip+0x11/0x50
[<ffffffff814130dd>] __down+0x6d/0xb0
[<ffffffff81089f71>] down+0x41/0x50
[<ffffffff810629ac>] acquire_console_sem+0x2c/0x50
[<ffffffff812ca53d>] unbind_con_driver+0xad/0x2d0
[<ffffffff8126f5f7>] fbcon_event_notify+0x457/0x890
[<ffffffff814144ff>] ? _raw_spin_unlock_irqrestore+0x1f/0x50
[<ffffffff81058051>] ? get_parent_ip+0x11/0x50
[<ffffffff8141836d>] notifier_call_chain+0x4d/0x70
[<ffffffff8108a3b8>] __blocking_notifier_call_chain+0x58/0x80
[<ffffffff8108a3f6>] blocking_notifier_call_chain+0x16/0x20
[<ffffffff8125dabb>] fb_notifier_call_chain+0x1b/0x20
[<ffffffff8125e6ac>] unregister_framebuffer+0x7c/0x130
[<ffffffff8125e8b3>] remove_conflicting_framebuffers+0x153/0x180
[<ffffffff8125eef3>] register_framebuffer+0x93/0x2c0
[<ffffffffa0331112>] drm_fb_helper_single_fb_probe+0x252/0x2f0 [drm_kms_helper]
[<ffffffffa03314a3>] drm_fb_helper_initial_config+0x2f3/0x6d0 [drm_kms_helper]
[<ffffffffa03318dd>] ? drm_fb_helper_single_add_all_connectors+0x5d/0x1c0 [drm_kms_helper]
[<ffffffffa037b588>] intel_fbdev_init+0xa8/0x160 [i915]
[<ffffffffa0343d74>] i915_driver_load+0x854/0x12b0 [i915]
[<ffffffffa02f0e7e>] drm_get_pci_dev+0x19e/0x360 [drm]
[<ffffffff8141821d>] ? sub_preempt_count+0x9d/0xd0
[<ffffffffa0386f91>] i915_pci_probe+0x15/0x17 [i915]
[<ffffffff8124481f>] local_pci_probe+0x5f/0xd0
[<ffffffff81244f89>] pci_device_probe+0x119/0x120
[<ffffffff812eccaa>] ? driver_sysfs_add+0x7a/0xb0
[<ffffffff812ed003>] driver_probe_device+0xa3/0x290
[<ffffffff812ed1f0>] ? __driver_attach+0x0/0xb0
[<ffffffff812ed29b>] __driver_attach+0xab/0xb0
[<ffffffff812ed1f0>] ? __driver_attach+0x0/0xb0
[<ffffffff812ebd3e>] bus_for_each_dev+0x5e/0x90
[<ffffffff812ecc2e>] driver_attach+0x1e/0x20
[<ffffffff812ec6f2>] bus_add_driver+0xe2/0x320
[<ffffffffa03aa000>] ? i915_init+0x0/0x96 [i915]
[<ffffffff812ed536>] driver_register+0x76/0x140
[<ffffffffa03aa000>] ? i915_init+0x0/0x96 [i915]
[<ffffffff81245216>] __pci_register_driver+0x56/0xd0
[<ffffffffa02f1264>] drm_pci_init+0xe4/0xf0 [drm]
[<ffffffffa03aa000>] ? i915_init+0x0/0x96 [i915]
[<ffffffffa02e84a8>] drm_init+0x58/0x70 [drm]
[<ffffffffa03aa094>] i915_init+0x94/0x96 [i915]
[<ffffffff81002194>] do_one_initcall+0x44/0x190
[<ffffffff810a066b>] sys_init_module+0xcb/0x210
[<ffffffff8100c012>] system_call_fastpath+0x16/0x1b
..
fb-test2 which reproduces above is available on kernel.org bug #26232.
To solve this issue, avoid calling lock_fb_info inside fb_set_suspend,
and move it out to where needed (callers of fb_set_suspend must call
lock_fb_info before if needed). So far, the only place which needs to
call lock_fb_info is store_fbstate, all other places which calls
fb_set_suspend are suspend/resume hooks that should not need the lock as
they should be run only when processes are already frozen in
suspend/resume.
References: https://bugzilla.kernel.org/show_bug.cgi?id=26232
Signed-off-by: Herton Ronaldo Krzesinski <herton@mandriva.com.br>
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Cc: stable@kernel.org
it's annoying and takes up way too much space in dmesg.
Signed-off-by: Manuel Lauss <manuel.lauss@googlemail.com>
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Increase delay when polling for tx status. This fixes
the unreliable video decoder i2c register access.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux:
drm/radeon/kms: make sure pci max read request size is valid on evergreen+ (v2)
drm/radeon/kms: set a default max_pixel_clock
* 'for-linus' of git://oss.sgi.com/xfs/xfs:
xfs: fix ->write_inode return values
xfs: fix xfs_mark_inode_dirty during umount
xfs: deprecate the nodelaylog mount option
The domain_flush_devices() function takes the domain->lock.
But this function is only called from update_domain() which
itself is already called unter the domain->lock. This causes
a deadlock situation when the dma-address-space of a domain
grows larger than 1GB.
Cc: stable@kernel.org
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
The value is only set to true but never set back to false,
which causes to many completion-wait commands to be sent to
hardware. Fix it with this patch.
Cc: stable@kernel.org
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
Firmware initiates roaming only after it reaches a rssi of 20.
This lower rssi threshold can be modified through a wmi command
to modify the roaming behavior.
kvalo: rename debugfs functions and move comment about rssi units next to
ath6kl_wmi_set_roam_lrssi_cmd()
Signed-off-by: Vivek Natarajan <nataraja@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Need to make sure the chip address for which we need the value
si endian safe.
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
If the bios or OS sets the pci max read request size to 0 or an
invalid value (6,7), it can result in a hang or slowdown. Check
and set it to something sane if it's invalid.
Fixes:
https://bugzilla.kernel.org/show_bug.cgi?id=42162
v2: use pci reg defines from include/linux/pci_regs.h
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@kernel.org
Reviewed-by: Michel Dänzer <michel.daenzer@amd.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
To dump a particular register:
echo <reg_addr> > <debugfs_root>/ieee80211/phyX/ath6kl/reg_addr
To dump the entire register set:
echo 0 > <debugfs_root>/ieee80211/phyX/ath6kl/reg_addr
Register values will be available at:
cat <debugfs_root>/ieee80211/phyX/ath6kl/reg_dump
kvalo: commit log cleanup, renamed few functions, removed a warning
message
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Firmare sends the logs only when it's internal ring buffer is full. But
if firmware crashes we need to retrieve the latest logs through diagnose
window. This is now done everytime the debugfs file is read.
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Just to make them a bit easier to read and unify naming. 32 suffix
in the function name means that it will be a 32 bit transfer. If there's
no number a buffer is transfered instead.
Use void pointers to get rid of ugly casts.
Don't provide target address as a pointer, pass it by value. Same for
the value used in write32().
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Firmware sends binary logs with WMIX_DBGLOG_EVENTID event. Create
a buffer which stores the latest logs and which can be copied from
fwlog debugfs file with cp command.
To save memory firmware log support is enabled only when CONFIG_ATH6KL_DEBUG
is enabled.
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
We have hit a couple of customer bugs where they would like to
use those parameters to run an UP kernel - but both of those
options turn of important sources of interrupt information so
we end up not being able to boot. The correct way is to
pass in 'dom0_max_vcpus=1' on the Xen hypervisor line and
the kernel will patch itself to be a UP kernel.
Fixes bug: http://bugs.debian.org/cgi-bin/bugreport.cgi?bug=637308
CC: stable@kernel.org
Acked-by: Ian Campbell <Ian.Campbell@eu.citrix.com>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
If vmalloc page_fault happens inside of interrupt handler with interrupts
disabled then on exit path from exception handler when there is no pending
interrupts, the following code (arch/x86/xen/xen-asm_32.S:112):
cmpw $0x0001, XEN_vcpu_info_pending(%eax)
sete XEN_vcpu_info_mask(%eax)
will enable interrupts even if they has been previously disabled according to
eflags from the bounce frame (arch/x86/xen/xen-asm_32.S:99)
testb $X86_EFLAGS_IF>>8, 8+1+ESP_OFFSET(%esp)
setz XEN_vcpu_info_mask(%eax)
Solution is in setting XEN_vcpu_info_mask only when it should be set
according to
cmpw $0x0001, XEN_vcpu_info_pending(%eax)
but not clearing it if there isn't any pending events.
Reproducer for bug is attached to RHBZ 707552
CC: stable@kernel.org
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Acked-by: Jeremy Fitzhardinge <jeremy@goop.org>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Since GPIOLIB is optional on ia64, GENERIC_GPIO must not be selected by
default. If GPIOLIB is enabled, it will select GENERIC_GPIO.
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: Tony Luck <tony.luck@intel.com>
After triggering a crash dump in a HVM guest, the PV backend drivers
will remain in Connected state. When the kdump kernel starts the PV
drivers will skip such devices. As a result, no root device is found and
the vmcore cant be saved.
A similar situation happens after a kexec boot, here the devices will be
in the Closed state.
With this change all frontend devices with state XenbusStateConnected or
XenbusStateClosed will be reset by changing the state file to Closing ->
Closed -> Initializing. This will trigger a disconnect in the backend
drivers. Now the frontend drivers will find the backend drivers in state
Initwait and can connect.
Signed-off-by: Olaf Hering <olaf@aepfle.de>
[v2:
- add timeout when waiting for backend state change
(based on feedback from Ian Campell)
- extent printk message to include backend string
- add comment to fall-through case in xenbus_reset_frontend]
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
During a kexec boot some virqs such as timer and debugirq were already
registered by the old kernel. The hypervisor will return -EEXISTS from
the new EVTCHNOP_bind_virq request and the BUG in bind_virq_to_irq()
triggers. Catch the -EEXISTS error and loop through all possible ports to find
what port belongs to the virq/cpu combo.
Signed-off-by: Olaf Hering <olaf@aepfle.de>
[v2:
- use NR_EVENT_CHANNELS instead of private MAX_EVTCHNS]
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
During repeated kexec boots xenwatch_thread() can crash because
xenbus_watch->callback is cleared by xenbus_watch_path() if a node/token
combo for a new watch happens to match an already registered watch from
an old kernel. In this case xs_watch returns -EEXISTS, then
register_xenbus_watch() does not remove the to-be-registered watch from
the list of active watches but returns the -EEXISTS to the caller
anyway.
Because the watch is still active in xenstored it will cause an event
which will arrive in the new kernel. process_msg() will find the
encapsulated struct xenbus_watch in its list of registered watches and
puts the "empty" watch handle in the queue for xenwatch_thread().
xenwatch_thread() then calls ->callback which was cleared earlier by
xenbus_watch_path().
To prevent that crash in a guest running on an old xen toolstack remove
the special -EEXIST handling.
v2:
- remove the EEXIST handing in register_xenbus_watch() instead of
checking for ->callback in process_msg()
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Signed-off-by: Olaf Hering <olaf@aepfle.de>
Modifies code that disables a bearer to ensure that all of its links
are deleted, not just its uncongested links. Similarly, modifies code
that blocks a bearer to ensure that all of its links are reset, not
just its uncongested links.
Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Saves a socket's TIPC_CONN_TIMEOUT socket option value in its original
form (milliseconds), rather than jiffies. This ensures that the exact
value set using setsockopt() is always returned by getsockopt(), without
being subject to rounding issues introduced by a ms->jiffies->ms
conversion sequence.
Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>