Eliminates code in tipc_send_buf_fast() that handles messages
sent to a destination on the current node, since the only caller
of the routine only passes in messages destined for other nodes.
Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Eliminates obsolete code that handles broadcast bearer congestion when
the broadast link sends a NACK message, since the broadcast pseudo-bearer
never becomes blocked.
Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Modifies TIPC's incoming broadcast packet handler to discard messages
that cannot legally be sent over the broadcast link, including:
- broadcast protocol messages that do no contain state information
- payload messages that are not named multicast messages
- any other form of message except for bundled messages, fragmented
messages, and name distribution messages.
These checks are needed to prevent TIPC from handing an unexpected
message to a routine that isn't prepared to handle it, which could
lead to incorrect processing (up to and including invalid memory
references caused by attempts to access message fields that aren't
present in the message).
Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Modifies TIPC's incoming broadcast packet handler so that it no longer
pre-reads information about the deferred packet queue, since the cached
value is unreliable once the associated node lock has been released.
Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Modifies TIPC's incoming broadcast packet handler to ensure that the
node lock associated with the sender of the packet is held whenever
node-related data structure fields are accessed. The routine is also
restructured with a single exit point, making it easier to ensure
the node lock is properly released and the incoming packet is properly
disposed of.
Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Ensure that broadcast link messages that have not been acknowledged
by a newly failed node do not get an implied acknowledgement until the
failed node is removed from the broadcast link's map of reachable nodes.
Previously, a race condition allowed a new broadcast link message to be
sent after the implicit acknowledgement processing was completed, but
before the map of reachable nodes was updated, resulting in the message
having an expected acknowledgement count that required the failed node
to explicitly acknowledge the message. Since this would never occur
the new message would remain in the broadcast link's transmit queue
forever, eventually causing the link to become congested and "stall".
Delaying the implicit acknowledgement processing until after the update
of the map of reachable nodes eliminates this race condition and prevents
stalling.
Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Enhances cleanup of broadcast link-related information when contact
with a node is lost.
1) All broadcast link-related cleanup now occurs only if the lost node
was capable of communicating over the broadcast link.
2) Following cleanup, the lost node is marked as no longer supporting
the broadcast link, ensuring that any remaining broadcast messages
received from that node prior to the re-establishment of a normal
communication link are ignored.
Thanks to Surya [Suryanarayana.Garlapati@emerson.com] for contributing
a prototype version of this patch.
Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Eliminates code associated with the sending of unsent broadcast link
traffic when the broadcast pseudo-bearer becomes unblocked following a
temporary congestion situation. This code is non-executable because the
broadcast pseudo-bearer never becomes blocked [see tipc_bcbearer_send()].
Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Updates the comments in the broadcast bearer send routine to more
accurately describe the processing done by the routine. Also replaces
the improper use of a TIPC payload message error status symbol (in a place
that has nothing to do with such errors) with its numeric equivalent.
Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Updates TIPC's broadcast link in a couple of places that were missed
during the transition from its former name ("multicast-link") to its
current name ("broadcast-link"). These changes are essentially cosmetic
and do not affect the overall operation of TIPC.
Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Ensure TIPC ignores an out-dated link reset message whose session
number predates the current session number. (Previously, TIPC only
ignored an out-date reset message whose session number was equal
to the current link session number.)
Out-dated link reset messages should not occur under normal circumstances;
however, they can be generated if a link endpoint is unable to send a
link reset message right away and queues it for later delivery, but the
queued message is not sent until after the link is established.
Thanks to Laser [gotolaser@gmail.com] for diagnosing the problem and
contributing a prototype patch.
Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Initializes the peer session number field of a newly created link
endpoint to an invalid value. This eliminates the remote possibility
that it will accidentally match the session number used by the peer
the first time the link is activated, and cause the link to ignore
a valid RESET message.
Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Sets the peer interface portion of the name of a newly created link
endpoint to "unknown". This ensures that state and statistics information
can be properly displayed during the time between the link endpoint's
creation and the time handshaking with its peer is completed.
Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Removes a test that ensures unicast link endpoints discard an incoming
message if it will not be consumed by the node itself and cannot be
forwarded to another node, since the preceding test already ensures that
the message is destined for this node and single-cluster TIPC no longer
performs message forwarding.
Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Eliminates code that increments and validates the re-route count field
of payload messages, since the elimination of multi-cluster support
means that it is no longer necessary for TIPC to forward incoming messages
to another node. (The obsolete code was incorrect anyway, since it
incorrectly incremented the re-route count field of messages that
originated on the node that forwarded the message.)
Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Currently we always redirty an inode that was attempted to be written out
synchronously but has been cleaned by an AIL pushed internall, which is
rather bogus. Fix that by doing the i_update_core check early on and
return 0 for it. Also include async calls for it, as doing any work for
those is just as pointless. While we're at it also fix the sign for the
EIO return in case of a filesystem shutdown, and fix the completely
non-sensical locking around xfs_log_inode.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Dave Chinner <dchinner@redhat.com>
Signed-off-by: Alex Elder <aelder@sgi.com>
(cherry picked from commit 297db93bb74cf687510313eb235a7aec14d67e97)
Signed-off-by: Alex Elder <aelder@sgi.com>
Use the domain's maximum reservation to limit the amount of extra RAM
for the memory balloon. This reduces the size of the pages tables and
the amount of reserved low memory (which defaults to about 1/32 of the
total RAM).
On a system with 8 GiB of RAM with the domain limited to 1 GiB the
kernel reports:
Before:
Memory: 627792k/4472000k available
After:
Memory: 549740k/11132224k available
A increase of about 76 MiB (~1.5% of the unused 7 GiB). The reserved
low memory is also reduced from 253 MiB to 32 MiB. The total
additional usable RAM is 329 MiB.
For dom0, this requires at patch to Xen ('x86: use 'dom0_mem' to limit
the number of pages for dom0') (c/s 23790)
CC: stable@kernel.org
Signed-off-by: David Vrabel <david.vrabel@citrix.com>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
If open fails with any error other than nfserr_replay_me, then the main
nfsd4_proc_compound() loop continues unconditionally to
nfsd4_encode_operation(), which will always call encode_seqid_op_tail.
Thus the condition we check for here does not occur.
Signed-off-by: J. Bruce Fields <bfields@redhat.com>
There are currently a couple races in the seqid replay code: a
retransmission could come while we're still encoding the original reply,
or a new seqid-mutating call could come as we're encoding a replay.
So, extend the state lock over the encoding (both encoding of a replayed
reply and caching of the original encoded reply).
I really hate doing this, and previously added the stateowner
reference-counting code to avoid it (which was insufficient)--but I
don't see a less complicated alternative at the moment.
Signed-off-by: J. Bruce Fields <bfields@redhat.com>
Probe Request reporting will be needed for P2P and WPS, but some
firmware builds do not seem to like this when P2P is not enabled.
Since we do not yet enable P2P, the safest option here is to just
remove this call for now and bring it back as a more dynamic version
once ath6kl starts advertising support for P2P.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Guest Memory Regions 2 is a way to bind pages to the GPU, but using
the FIFO instead of an io-submitted descriptor chain.
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
Reviewed-by: Jakob Bornecantz <jakob@vmware.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
Reviewed-by: José Fonseca <jfonseca@vmware.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
When GMR2 is available, make sure we restrict the number of used GMR pages
to the limit indicated by the device.
This is done by failing a GMRID allocation if the total number of GMR pages
exceeds the limit.
As a result TTM will then start evicting buffers in GMR memory on a
LRU basis until the allocation succeeds.
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
Reviewed-by: Jakob Bornecrantz <jakob@vmware.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Previously this was not done when any 3D resource was active,
since that meant disabling the fifo with all 3D state lost.
Now, if there are still 3D resources active, we use the svga hide feature.
This fixes X server VT switching with 3D enabled.
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
Reviewed-by: Jakob Bornecrantz <jakob@vmware.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Perform all command stream validation in a bounce buffer separate from the
fifo. This makes the fifo available to all validation-generated commands,
which would otherwise attempt to grab the fifo recursively, causing a
deadlock. This is in preparation for GMR2 and swappable surfaces.
Also maintain references to all surfaces in the command stream until the
command stream has been fired in order to avoid racing with surface
destruction taking place after validation but before submission.
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
Reviewed-by: Jakob Bornecrantz <jakob@vmware.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Signed-off-by: Michel Dänzer <daenzer@vmware.com>
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Signed-off-by: Michel Dänzer <daenzer@vmware.com>
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Signed-off-by: Michel Dänzer <daenzer@vmware.com>
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Signed-off-by: Michel Dänzer <daenzer@vmware.com>
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
The hook dma_get_required_mask is supposed to return the mask required
by the platform to operate efficently. The generic version of
dma_get_required_mask in driver/base/platform.c returns a mask based
only on max_pfn. However, this is likely too big for iommu systems
and could be too small for platforms that require a dma offset or have
a secondary window at a high offset.
Override the default, provide a hook in ppc_md used by pseries lpar and
cell, and provide the default answer based on memblock_end_of_DRAM(),
with hooks for get_dma_offset, and provide an implementation for iommu
that looks at the defined table size. Coverting from the end address
to the required bit mask is based on the generic implementation.
The need for this was discovered when the qla2xxx driver switched to
64 bit dma then reverted to 32 bit when dma_get_required_mask said
32 bits was sufficient.
Signed-off-by: Milton Miller <miltonm@bga.com>
Signed-off-by: Nishanth Aravamudan <nacc@us.ibm.com>
Cc: linuxppc-dev@lists.ozlabs.org
Cc: linux-kernel@vger.kernel.org
Cc: benh@kernel.crashing.org
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
If second CPU is not enabled, CPC925 EDAC driver will spill out warnings
about errors on second Processor Interface. Support masking that out,
by detecting at runtime which CPUs are present in device tree.
Signed-off-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Cc: Harry Ciao <qingtao.cao@windriver.com>
Cc: Doug Thompson <dougthompson@xmission.com>
Signed-off-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
> [34883.426065] tm6000 #0: registered device video0
> [34883.430591] Trident TVMaster TM5600/TM6000/TM6010 USB2 board (Load status: 0)
> [34883.437763] usbcore: registered new interface driver tm6000
> [34884.608372] BUG: unable to handle kernel NULL pointer dereference at 00000002
> [34884.615514] IP: [<f8c4ceea>] tm6000_reset+0xd7/0x11c [tm6000]
The dev->int_in USB interfaces is used by some devices for the
Remote Controller. Not all devices seem to define this interface,
so, tm6000_reset should not try to set the interface to it on
such devices.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The standard timings parses uses 1:1 dimensions when the ratio in the
EDID data is 0. However, for EDID 1.3 and later the dimensions are 16:10
when the ratio is 0.
Pass the version and revision numbers to get_std_timing() which can then
make the right decision about dimensions.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Include linux/module.h to fix below build error:
from drivers/video/mxsfb.c:42:
arch/arm/mach-mxs/include/mach/memory.h:22:1: warning: this is the location of the previous definition
drivers/video/mxsfb.c:574: error: 'THIS_MODULE' undeclared here (not in a function)
drivers/video/mxsfb.c:893: warning: data definition has no type or storage class
drivers/video/mxsfb.c:893: warning: type defaults to 'int' in declaration of 'MODULE_DEVICE_TABLE'
drivers/video/mxsfb.c:893: warning: parameter names (without types) in function declaration
drivers/video/mxsfb.c:917: error: expected declaration specifiers or '...' before string constant
drivers/video/mxsfb.c:917: warning: data definition has no type or storage class
drivers/video/mxsfb.c:917: warning: type defaults to 'int' in declaration of 'MODULE_DESCRIPTION'
drivers/video/mxsfb.c:917: warning: function declaration isn't a prototype
drivers/video/mxsfb.c:918: error: expected declaration specifiers or '...' before string constant
drivers/video/mxsfb.c:918: warning: data definition has no type or storage class
drivers/video/mxsfb.c:918: warning: type defaults to 'int' in declaration of 'MODULE_AUTHOR'
drivers/video/mxsfb.c:918: warning: function declaration isn't a prototype
drivers/video/mxsfb.c:919: error: expected declaration specifiers or '...' before string constant
drivers/video/mxsfb.c:919: warning: data definition has no type or storage class
drivers/video/mxsfb.c:919: warning: type defaults to 'int' in declaration of 'MODULE_LICENSE'
drivers/video/mxsfb.c:919: warning: function declaration isn't a prototype
make[2]: *** [drivers/video/mxsfb.o] Error 1
make[1]: *** [drivers/video] Error 2
make: *** [drivers] Error 2
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
During umount we do not add a dirty inode to the lru and wait for it to
become clean first, but force writeback of data and metadata with
I_WILL_FREE set. Currently there is no way for XFS to detect that the
inode has been redirtied for metadata operations, as we skip the
mark_inode_dirty call during teardown. Fix this by setting i_update_core
nanually in that case, so that the inode gets flushed during inode reclaim.
Alternatively we could enable calling mark_inode_dirty for inodes in
I_WILL_FREE state, and let the VFS dirty tracking handle this. I decided
against this as we will get better I/O patterns from reclaim compared to
the synchronous writeout in write_inode_now, and always marking the inode
dirty in some way from xfs_mark_inode_dirty is a better safetly net in
either case.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Dave Chinner <dchinner@redhat.com>
Signed-off-by: Alex Elder <aelder@sgi.com>
(cherry picked from commit da6742a5a4cc844a9982fdd936ddb537c0747856)
Signed-off-by: Alex Elder <aelder@sgi.com>
Now that the replay owner is in the cstate we can remove it from a lot
of other individual operations and further simplify
nfs4_preprocess_seqid_op().
Signed-off-by: J. Bruce Fields <bfields@redhat.com>
Set the stateowner associated with a replay in one spot in
nfs4_preprocess_seqid_op() and keep it in cstate. This allows removing
a few lines of boilerplate from all the nfs4_preprocess_seqid_op()
callers.
Also turn ENCODE_SEQID_OP_TAIL into a function while we're here.
Signed-off-by: J. Bruce Fields <bfields@redhat.com>
Thanks to Casey for reminding me that 5661 gives a special meaning to a
value of 0 in the stateid's seqid field, so all stateid's should start
out with si_generation 1. We were doing that in the open and lock
cases for minorversion 1, but not for the delegation stateid, and not
for openstateid's with v4.0.
It doesn't *really* matter much for v4.0 or for delegation stateid's
(which never get the seqid field incremented), but we may as well do the
same for all of them.
Reported-by: Casey Bodley <cbodley@citi.umich.edu>
Signed-off-by: J. Bruce Fields <bfields@redhat.com>
Follow the recommendation from rfc3530bis for stateid generation number
wraparound, simplify some code, and fix or remove incorrect comments.
Signed-off-by: J. Bruce Fields <bfields@redhat.com>