Commit graph

1,431,295 commits

Author SHA1 Message Date
Javier Tia
e4f6bc7f82 Bluetooth: btmtk: fix ISO interface setup for single alt setting
Some MT6639 Bluetooth USB interfaces (e.g. IMC Networks 13d3:3588 on
ASUS ROG STRIX X870E-E and ProArt X870E-Creator boards) expose only a
single alternate setting (alt 0) on the ISO interface. The driver
unconditionally requests alt setting 1, which fails with EINVAL on
these devices, causing a ~20 second initialization delay and no LE
audio support.

Check the number of available alternate settings before selecting one.
If only alt 0 exists, use it; otherwise request alt 1 as before.

Closes: https://github.com/jetm/mediatek-mt7927-dkms/pull/39
Signed-off-by: Javier Tia <floss@jetm.me>
Reported-by: Ryan Gilbert <xelnaga@gmail.com>
Tested-by: Ryan Gilbert <xelnaga@gmail.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
2026-04-13 09:18:16 -04:00
Javier Tia
28b7c5a6db Bluetooth: btmtk: Add MT6639 (MT7927) Bluetooth support
The MediaTek MT7927 (Filogic 380) combo WiFi 7 + BT 5.4 module uses
hardware variant 0x6639 for its Bluetooth subsystem. Without this patch,
the chip fails with "Unsupported hardware variant (00006639)" or hangs
during firmware download.

Three changes are needed to support MT6639:

1. CHIPID workaround: On some boards the BT USB MMIO register reads
   0x0000 for dev_id, causing the driver to skip the 0x6639 init path.
   Force dev_id to 0x6639 only when the USB VID/PID matches a known
   MT6639 device, avoiding misdetection if a future chip also reads
   zero. This follows the WiFi-side pattern that uses PCI device IDs
   to scope the same workaround.

2. Firmware naming: MT6639 uses firmware version prefix "2_1" instead of
   "1_1" used by MT7925 and other variants. The firmware path is
   mediatek/mt7927/BT_RAM_CODE_MT6639_2_1_hdr.bin, using the mt7927
   directory to match the WiFi firmware convention. The filename will
   likely change to use MT7927 once MediaTek submits a dedicated
   Linux firmware binary.

3. Section filtering: The MT6639 firmware binary contains 9 sections, but
   only sections with (dlmodecrctype & 0xff) == 0x01 are Bluetooth-related.
   Sending the remaining WiFi/other sections causes an irreversible BT
   subsystem hang requiring a full power cycle. This matches the Windows
   driver behavior observed via USB captures.

Also add 0x6639 to the reset register (CONNV3) and firmware setup switch
cases alongside the existing 0x7925 handling.

Link: https://bugzilla.kernel.org/show_bug.cgi?id=221096
Link: https://github.com/openwrt/mt76/issues/927
Reported-by: Ryan Gilbert <xelnaga@gmail.com>
Signed-off-by: Javier Tia <floss@jetm.me>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
2026-04-13 09:18:16 -04:00
Pauli Virtanen
5c7209a341 Bluetooth: fix locking in hci_conn_request_evt() with HCI_PROTO_DEFER
When protocol sets HCI_PROTO_DEFER, hci_conn_request_evt() calls
hci_connect_cfm(conn) without hdev->lock. Generally hci_connect_cfm()
assumes it is held, and if conn is deleted concurrently -> UAF.

Only SCO and ISO set HCI_PROTO_DEFER and only for defer setup listen,
and HCI_EV_CONN_REQUEST is not generated for ISO.  In the non-deferred
listening socket code paths, hci_connect_cfm(conn) is called with
hdev->lock held.

Fix by holding the lock.

Fixes: 70c4642563 ("Bluetooth: Refactor connection request handling")
Signed-off-by: Pauli Virtanen <pav@iki.fi>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
2026-04-13 09:18:16 -04:00
Johan Hovold
120941654f Bluetooth: btmtk: refactor endpoint lookup
Use the common USB helper for looking up bulk and interrupt endpoints
instead of open coding.

Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
2026-04-13 09:18:16 -04:00
Johan Hovold
5c31aaa056 Bluetooth: btusb: refactor endpoint lookup
Use the common USB helper for looking up bulk and interrupt endpoints
instead of open coding.

Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
2026-04-13 09:18:16 -04:00
Jonathan Rissanen
68d39ea5e0 Bluetooth: hci_ldisc: Clear HCI_UART_PROTO_INIT on error
When hci_register_dev() fails in hci_uart_register_dev()
HCI_UART_PROTO_INIT is not cleared before calling hu->proto->close(hu)
and setting hu->hdev to NULL. This means incoming UART data will reach
the protocol-specific recv handler in hci_uart_tty_receive() after
resources are freed.

Clear HCI_UART_PROTO_INIT with a write lock before calling
hu->proto->close() and setting hu->hdev to NULL. The write lock ensures
all active readers have completed and no new reader can enter the
protocol recv path before resources are freed.

This allows the protocol-specific recv functions to remove the
"HCI_UART_REGISTERED" guard without risking a null pointer dereference
if hci_register_dev() fails.

Fixes: 5df5dafc17 ("Bluetooth: hci_uart: Fix another race during initialization")
Signed-off-by: Jonathan Rissanen <jonathan.rissanen@axis.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
2026-04-13 09:18:16 -04:00
Pauli Virtanen
d288f4db09 Bluetooth: hci_sync: make hci_cmd_sync_run_once return -EEXIST if exists
hci_cmd_sync_run_once() needs to indicate whether a queue item was
added, so caller can know if callbacks are called, so it can avoid
leaking resources.

Change the function to return -EEXIST if queue item already exists.

Modify all callsites vs. the changes.  The only callsite is
hci_abort_conn().

Signed-off-by: Pauli Virtanen <pav@iki.fi>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
2026-04-13 09:18:16 -04:00
Shuai Zhang
7b75867803 Bluetooth: hci_qca: disable power control for WCN7850 when bt_en is not defined
On platforms using an M.2 slot with both UART and USB support, bt_en is
pulled high by hardware. In this case, software-based power control
should be disabled. The current platforms are Lemans-EVK and Monaco-EVK.

Add QCA_WCN7850 to the existing condition so that power_ctrl_enabled is
cleared when bt_en is not software-controlled (or absent), aligning its
behavior with WCN6750 and WCN6855

Signed-off-by: Shuai Zhang <shuai.zhang@oss.qualcomm.com>
Reviewed-by: Bartosz Golaszewski <bartosz.golaszewski@oss.qualcomm.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
2026-04-13 09:18:16 -04:00
Lukas Kraft
552aac414f bluetooth: btusb: Fix whitespace in btusb.c
Replace single space with tab and insert blank line after declaration, according to checkpatch

Signed-off-by: Lukas Kraft <rebootrequired42@gmail.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
2026-04-13 09:18:16 -04:00
Luiz Augusto von Dentz
15bf35a660 Bluetooth: L2CAP: Fix printing wrong information if SDU length exceeds MTU
The code was printing skb->len and sdu_len in the places where it should
be sdu_len and chan->imtu respectively to match the if conditions.

Link: https://lore.kernel.org/linux-bluetooth/20260315132013.75ab40c5@kernel.org/T/#m1418f9c82eeff8510c1beaa21cf53af20db96c06
Fixes: e1d9a66889 ("Bluetooth: LE L2CAP: Disconnect if received packet's SDU exceeds IMTU")
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Reviewed-by: Paul Menzel <pmenzel@molgen.mpg.de>
2026-04-13 09:17:52 -04:00
Dmitry Baryshkov
9f168e4de5 Bluetooth: qca: enable pwrseq support for WCN39xx devices
The WCN39xx family of WiFi/BT chips incorporates a simple PMU, spreading
voltages over internal rails. Implement support for using powersequencer
for this family of QCA devices in addition to using regulators.

Reviewed-by: Bartosz Golaszewski <bartosz.golaszewski@oss.qualcomm.com>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
2026-04-10 10:30:18 -04:00
Luiz Augusto von Dentz
15a315e417 Bluetooth: btintel_pci: Fix btintel_pcie_read_hwexp code style
Use proper alignment for break under a switch.

Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
2026-04-10 10:30:01 -04:00
Kiran K
5741118b5d Bluetooth: btintel_pcie: Add device id of Scorpious2, Nova Lake-PCD-S
sudo lspci -v -k -d 8086:6e74
	80:14.7 Bluetooth: Intel Corporation Device 6e74 (rev 10)
        Subsystem: Intel Corporation Device 0011
        Flags: bus master, fast devsel, latency 0, IRQ 16
        Memory at 200002a8000 (64-bit, non-prefetchable) [size=16K]
        Capabilities: [c8] Power Management version 3
        Capabilities: [d0] MSI: Enable- Count=1/1 Maskable- 64bit+
        Capabilities: [40] Express Root Complex Integrated Endpoint, MSI 00
        Capabilities: [80] MSI-X: Enable+ Count=32 Masked-
        Capabilities: [100] Latency Tolerance Reporting
        Kernel driver in use: btintel_pcie
        Kernel modules: btintel_pcie

Signed-off-by: Kiran K <kiran.k@intel.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
2026-04-10 10:29:42 -04:00
Kiran K
0e77b6ad7a Bluetooth: btintel_pcie: Add device id of Scorpius Peak2, Nova Lake-PCD-H
sudo lspci -v -k -d 8086:d346
	00:14.7 Bluetooth: Intel Corporation Device d346
	Subsystem: Intel Corporation Device 0011
	Flags: bus master, fast devsel, latency 0, IRQ 16, IOMMU group 14
	Memory at b018378000 (64-bit, non-prefetchable) [size=16K]
	Capabilities: [c8] Power Management version 3
	Capabilities: [d0] MSI: Enable- Count=1/1 Maskable- 64bit+
	Capabilities: [40] Express Root Complex Integrated Endpoint, MSI 00
	Capabilities: [80] MSI-X: Enable+ Count=32 Masked-
	Capabilities: [100] Latency Tolerance Reporting
	Kernel driver in use: btintel_pcie
	Kernel modules: btintel_pcie

Signed-off-by: Kiran K <kiran.k@intel.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
2026-04-10 10:29:23 -04:00
Kiran K
68a1729ae5 Bluetooth: btintel_pcie: Add support for exception dump for ScP2F
Add device coredump support for Scorpious Peak2F product.

Signed-off-by: Kiran K <kiran.k@intel.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
2026-04-10 10:29:03 -04:00
Kiran K
9c52085e10 Bluetooth: btintel: Add support for Scorpious Peak2F support
Add support for Intel Bluetooth Scorpious Peak2F core.

Signed-off-by: Kiran K <kiran.k@intel.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
2026-04-10 10:28:44 -04:00
Kiran K
e64621ef15 Bluetooth: btintel_pcie: Add support for exception dump for ScP2
Add device coredump support for Scorpious Peak2 product.

Signed-off-by: Kiran K <kiran.k@intel.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
2026-04-10 10:28:25 -04:00
Kiran K
140f6afd3d Bluetooth: btintel: Add DSBR support for ScP2 onwards
Add DSBR support for Scorpious Peak2 cores onwards.

Refer commit eb9e749c01 ("Bluetooth: btintel: Allow configuring drive
strength of BRI") for details about DSBR.

Signed-off-by: Kiran K <kiran.k@intel.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
2026-04-10 10:28:05 -04:00
Kiran K
3b74115bb3 Bluetooth: btintel: Add support for Scorpious Peak2 support
Add support for Intel Bluetooth Scorpious Peak2 core.

Signed-off-by: Kiran K <kiran.k@intel.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
2026-04-10 10:27:46 -04:00
Kiran K
c239ad6e53 Bluetooth: btintel: Replace CNVi id with hardware variant
Use hardware variant instead of CNVi to send dsbr command.

Signed-off-by: Kiran K <kiran.k@intel.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
2026-04-10 10:27:27 -04:00
Kiran K
21b51648f3 Bluetooth: btintel: Add support for hybrid signature for ScP2 onwards
If FW image has hybrid signature (ECDSA and LMS) then send CSS header,
ECDSA public key, ECDSA signature, LMS public key, LMS signature and
command buffer to device.

Signed-off-by: Kiran K <kiran.k@intel.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
2026-04-10 10:27:08 -04:00
Christian Eggers
728a3d1283 Bluetooth: L2CAP: CoC: Disconnect if received packet size exceeds MPS
Core 6.0, Vol 3, Part A, 3.4.3:
"... If the payload size of any K-frame exceeds the receiver's MPS, the
receiver shall disconnect the channel..."

This fixes L2CAP/LE/CFC/BV-27-C (running together with 'l2test -r -P
0x0027 -V le_public -I 100').

Signed-off-by: Christian Eggers <ceggers@arri.de>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Tested-by: Christian Eggers <ceggers@arri.de>
2026-04-10 10:26:48 -04:00
Sean Wang
7f2c3c49ba Bluetooth: btmtk: add MT7902 SDIO support
Add MT7902 Bluetooth SDIO support by introducing chip data and
registering the device ID.

Runtime PM is not yet supported by the driver, but normal operation
is unaffected.

Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
2026-04-10 10:26:31 -04:00
Sean Wang
22fd19bf24 Bluetooth: btusb: Add new VID/PID 0e8d/1ede for MT7902
Add VID 0e8d & PID 1ede for MediaTek MT7902 USB Bluetooth chip.

The information in /sys/kernel/debug/usb/devices about the Bluetooth
device is listed as the below.

T:  Bus=01 Lev=01 Prnt=01 Port=05 Cnt=02 Dev#=  4 Spd=480  MxCh= 0
D:  Ver= 2.10 Cls=ef(misc ) Sub=02 Prot=01 MxPS=64 #Cfgs=  1
P:  Vendor=0e8d ProdID=1ede Rev= 1.00
S:  Manufacturer=MediaTek Inc.
S:  Product=Wireless_Device
S:  SerialNumber=000000000
C:* #Ifs= 3 Cfg#= 1 Atr=e0 MxPwr=100mA
A:  FirstIf#= 0 IfCount= 3 Cls=e0(wlcon) Sub=01 Prot=01
I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=81(I) Atr=03(Int.) MxPS=  16 Ivl=125us
E:  Ad=82(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=   0 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=   0 Ivl=1ms
I:  If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=   9 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=   9 Ivl=1ms
I:  If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=  17 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  17 Ivl=1ms
I:  If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=  25 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  25 Ivl=1ms
I:  If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=  33 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  33 Ivl=1ms
I:  If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=  49 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  49 Ivl=1ms
I:  If#= 1 Alt= 6 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=  63 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  63 Ivl=1ms
I:  If#= 2 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=8a(I) Atr=03(Int.) MxPS=  64 Ivl=125us
E:  Ad=0a(O) Atr=03(Int.) MxPS=  64 Ivl=125us
I:* If#= 2 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=8a(I) Atr=03(Int.) MxPS= 512 Ivl=125us
E:  Ad=0a(O) Atr=03(Int.) MxPS= 512 Ivl=125us

Co-developed-by: Bitterblue Smith <rtl8821cerfe2@gmail.com>
Signed-off-by: Bitterblue Smith <rtl8821cerfe2@gmail.com>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
2026-04-10 10:26:12 -04:00
Sean Wang
6724fb35cd Bluetooth: btusb: Add new VID/PID 13d3/3596 for MT7902
Add VID 13d3 & PID 3596 for MediaTek MT7902 USB Bluetooth chip.

The information in /sys/kernel/debug/usb/devices about the Bluetooth
device is listed as the below.

T:  Bus=07 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#=  2 Spd=480  MxCh= 0
D:  Ver= 2.10 Cls=ef(misc ) Sub=02 Prot=01 MxPS=64 #Cfgs=  1
P:  Vendor=13d3 ProdID=3596 Rev= 1.00
S:  Manufacturer=MediaTek Inc.
S:  Product=Wireless_Device
S:  SerialNumber=000000000
C:* #Ifs= 3 Cfg#= 1 Atr=e0 MxPwr=100mA
A:  FirstIf#= 0 IfCount= 3 Cls=e0(wlcon) Sub=01 Prot=01
I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=81(I) Atr=03(Int.) MxPS=  16 Ivl=125us
E:  Ad=82(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=   0 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=   0 Ivl=1ms
I:  If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=   9 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=   9 Ivl=1ms
I:  If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=  17 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  17 Ivl=1ms
I:  If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=  25 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  25 Ivl=1ms
I:  If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=  33 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  33 Ivl=1ms
I:  If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=  49 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  49 Ivl=1ms
I:  If#= 1 Alt= 6 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=  63 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  63 Ivl=1ms
I:* If#= 2 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=(none)
E:  Ad=8a(I) Atr=03(Int.) MxPS=  64 Ivl=125us
E:  Ad=0a(O) Atr=03(Int.) MxPS=  64 Ivl=125us
I:  If#= 2 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=(none)
E:  Ad=8a(I) Atr=03(Int.) MxPS= 512 Ivl=125us
E:  Ad=0a(O) Atr=03(Int.) MxPS= 512 Ivl=125us

Co-developed-by: Kush Kulshrestha <kush.kulshrestha.5@gmail.com>
Signed-off-by: Kush Kulshrestha <kush.kulshrestha.5@gmail.com>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
2026-04-10 10:25:53 -04:00
Sean Wang
7968f6d34e Bluetooth: btusb: Add new VID/PID 13d3/3594 for MT7902
Add VID 13d3 & PID 3594 for MediaTek MT7902 USB Bluetooth chip.

The information in /sys/kernel/debug/usb/devices about the Bluetooth
device is listed as the below.

T: Bus=03 Lev=01 Prnt=01 Port=02 Cnt=01 Dev#= 3 Spd=480 MxCh= 0
D: Ver= 2.10 Cls=ef(misc ) Sub=02 Prot=01 MxPS=64 #Cfgs= 1
P: Vendor=13d3 ProdID=3594 Rev= 1.00
S: Manufacturer=MediaTek Inc.
S: Product=Wireless_Device
S: SerialNumber=000000000
C:* #Ifs= 3 Cfg#= 1 Atr=e0 MxPwr=100mA
A: FirstIf#= 0 IfCount= 3 Cls=e0(wlcon) Sub=01 Prot=01
I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=81(I) Atr=03(Int.) MxPS= 16 Ivl=125us
E: Ad=82(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 0 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 0 Ivl=1ms
I: If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 9 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 9 Ivl=1ms
I: If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 17 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 17 Ivl=1ms
I: If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 25 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 25 Ivl=1ms
I: If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 33 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 33 Ivl=1ms
I: If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 49 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 49 Ivl=1ms
I: If#= 1 Alt= 6 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 63 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 63 Ivl=1ms
I:* If#= 2 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=(none)
E: Ad=8a(I) Atr=03(Int.) MxPS= 64 Ivl=125us
E: Ad=0a(O) Atr=03(Int.) MxPS= 64 Ivl=125us
I: If#= 2 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=(none)
E: Ad=8a(I) Atr=03(Int.) MxPS= 512 Ivl=125us
E: Ad=0a(O) Atr=03(Int.) MxPS= 512 Ivl=125us

Co-developed-by: Kush Kulshrestha <kush.kulshrestha.5@gmail.com>
Signed-off-by: Kush Kulshrestha <kush.kulshrestha.5@gmail.com>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
2026-04-10 10:25:34 -04:00
Sean Wang
cdb7f671bc Bluetooth: btusb: Add new VID/PID 13d3/3580 for MT7902
Add VID 13d3 & PID 3580 for MediaTek MT7902 USB Bluetooth chip.

The information in /sys/kernel/debug/usb/devices about the Bluetooth
device is listed as the below.

T:  Bus=03 Lev=01 Prnt=01 Port=02 Cnt=01 Dev#=  2 Spd=480  MxCh= 0
D:  Ver= 2.10 Cls=ef(misc ) Sub=02 Prot=01 MxPS=64 #Cfgs=  1
P:  Vendor=13d3 ProdID=3580 Rev= 1.00
S:  Manufacturer=MediaTek Inc.
S:  Product=Wireless_Device
S:  SerialNumber=000000000
C:* #Ifs= 3 Cfg#= 1 Atr=e0 MxPwr=100mA
A:  FirstIf#= 0 IfCount= 3 Cls=e0(wlcon) Sub=01 Prot=01
I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=81(I) Atr=03(Int.) MxPS=  16 Ivl=125us
E:  Ad=82(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=   0 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=   0 Ivl=1ms
I:  If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=   9 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=   9 Ivl=1ms
I:  If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=  17 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  17 Ivl=1ms
I:  If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=  25 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  25 Ivl=1ms
I:  If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=  33 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  33 Ivl=1ms
I:  If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=  49 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  49 Ivl=1ms
I:  If#= 1 Alt= 6 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=  63 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  63 Ivl=1ms
I:  If#= 2 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=8a(I) Atr=03(Int.) MxPS=  64 Ivl=125us
E:  Ad=0a(O) Atr=03(Int.) MxPS=  64 Ivl=125us
I:* If#= 2 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=8a(I) Atr=03(Int.) MxPS= 512 Ivl=125us
E:  Ad=0a(O) Atr=03(Int.) MxPS= 512 Ivl=125us

Co-developed-by: Kush Kulshrestha <kush.kulshrestha.5@gmail.com>
Signed-off-by: Kush Kulshrestha <kush.kulshrestha.5@gmail.com>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
2026-04-10 10:25:15 -04:00
Sean Wang
51c4173b89 Bluetooth: btusb: Add new VID/PID 13d3/3579 for MT7902
Add VID 13d3 & PID 3579 for MediaTek MT7902 USB Bluetooth chip.

The information in /sys/kernel/debug/usb/devices about the Bluetooth
device is listed as the below.

T:  Bus=01 Lev=01 Prnt=01 Port=09 Cnt=04 Dev#=  7 Spd=480  MxCh= 0
D:  Ver= 2.10 Cls=ef(misc ) Sub=02 Prot=01 MxPS=64 #Cfgs=  1
P:  Vendor=13d3 ProdID=3579 Rev= 1.00
S:  Manufacturer=MediaTek Inc.
S:  Product=Wireless_Device
S:  SerialNumber=000000000
C:* #Ifs= 3 Cfg#= 1 Atr=e0 MxPwr=100mA
A:  FirstIf#= 0 IfCount= 3 Cls=e0(wlcon) Sub=01 Prot=01
I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=81(I) Atr=03(Int.) MxPS=  16 Ivl=125us
E:  Ad=82(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=   0 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=   0 Ivl=1ms
I:  If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=   9 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=   9 Ivl=1ms
I:  If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=  17 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  17 Ivl=1ms
I:  If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=  25 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  25 Ivl=1ms
I:  If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=  33 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  33 Ivl=1ms
I:  If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=  49 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  49 Ivl=1ms
I:  If#= 1 Alt= 6 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=  63 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  63 Ivl=1ms
I:  If#= 2 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=8a(I) Atr=03(Int.) MxPS=  64 Ivl=125us
E:  Ad=0a(O) Atr=03(Int.) MxPS=  64 Ivl=125us
I:* If#= 2 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=8a(I) Atr=03(Int.) MxPS= 512 Ivl=125us
E:  Ad=0a(O) Atr=03(Int.) MxPS= 512 Ivl=125us

Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
2026-04-10 10:24:56 -04:00
Sean Wang
aab25984e5 Bluetooth: btmtk: add MT7902 MCU support
Add MT7902 device ID and firmware filename to enable MCU firmware
loading.

Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
2026-04-10 10:24:37 -04:00
Sean Wang
cde32a92d4 mmc: sdio: add MediaTek MT7902 SDIO device ID
Add SDIO device ID (0x790a) for MediaTek MT7902 to sdio_ids.h.

Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
2026-04-10 10:24:21 -04:00
Thorsten Blum
9a9d21f780 Bluetooth: btintel_pcie: Use struct_size to improve hci_drv_read_info
Use struct_size(), which provides additional compile-time checks for
structures with flexible array members (e.g., __must_be_array()), to
determine the allocation size for a new 'struct hci_drv_rp_read_info'.

Signed-off-by: Thorsten Blum <thorsten.blum@linux.dev>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
2026-04-10 10:24:01 -04:00
Dylan Eray
67377cd38b Bluetooth: btusb: Add Lite-On 04ca:3807 for MediaTek MT7921
Add USB device ID (04ca:3807) for a Lite-On Wireless_Device containing
a MediaTek MT7921 (MT7920) Bluetooth chipset found in Acer laptops.

Without this entry, btusb binds via the generic USB class-based wildcard
match but never sets the BTUSB_MEDIATEK flag. This means btmtk never
triggers firmware loading, and the driver sends a raw HCI Reset that
the uninitialized chip cannot respond to, resulting in:

  Bluetooth: hci0: Opcode 0x0c03 failed: -110

The information in /sys/kernel/debug/usb/devices about the Bluetooth
device is listed as the below:

T:  Bus=03 Lev=01 Prnt=01 Port=09 Cnt=01 Dev#=5 Spd=480 MxCh=0
P:  Vendor=04ca ProdID=3807 Rev=1.00
S:  Manufacturer=MediaTek Inc.
S:  Product=Wireless_Device
S:  SerialNumber=000000000
C:  #Ifs= 3 Cfg#= 1 Atr=e0 MxPwr=100mA
I:  If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
I:  If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
I:  If#= 2 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=(none)

Reviewed-by: Paul Menzel <pmenzel@molgen.mpg.de>
Signed-off-by: Dylan Eray <dylan.eray6@gmail.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
2026-04-10 10:23:41 -04:00
Thorsten Blum
c0ad33d273 Bluetooth: btintel_pcie: Replace snprintf("%s") with strscpy
Replace snprintf("%s", ...) with the faster and more direct strscpy().

Signed-off-by: Thorsten Blum <thorsten.blum@linux.dev>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
2026-04-10 10:23:21 -04:00
Hans de Goede
9ff5ff0b91 Bluetooth: hci_qca: Fix BT not getting powered-off on rmmod
The BT core skips calling the hci_dev's shutdown method when the HCI
is unregistered. This means that qca_power_off() was not getting called
leaving BT powered on.

This causes regulators / pwrseq providers to not get disabled which also
causes problem when re-loading the module because regulators and pwrseq
providers have an enablecount which now has never dropped to 0, causing
the BT to not get properly reset between rmmod and re-load which causes
initialization failure on the re-load.

Fix this by calling qca_power_off() from qca_close() when BT has not
already been powered off through a qca_hci_shutdown() call.

hci_ldisc.c will call qca_close() after freeing the hdev, so this
means that qca_power_off() can now no longer deref hu->hdev, change
the logging in qca_power_off() to no longer use hu->hdev.

Signed-off-by: Hans de Goede <johannes.goede@oss.qualcomm.com>
Reviewed-by: Bartosz Golaszewski <bartosz.golaszewski@oss.qualcomm.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
2026-04-10 10:23:02 -04:00
Hans de Goede
7e2e1e5859 Bluetooth: hci_qca: Fix confusing shutdown() and power_off() naming
The function called qca_power_off() is actually the hci_dev shutdown
handler, rename it to qca_hci_shutdown() to make this clear.

While the qca_power_shutdown() function is actually the counter-part
of qca_power_on() rename it to qca_power_off() to make this clear.

Signed-off-by: Hans de Goede <johannes.goede@oss.qualcomm.com>
Reviewed-by: Paul Menzel <pmenzel@molgen.mpg.de>
Reviewed-by: Bartosz Golaszewski <bartosz.golaszewski@oss.qualcomm.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
2026-04-10 10:22:42 -04:00
Marek Vasut
04c217a7fc Bluetooth: btbcm: Add entry for BCM4343A2 UART Bluetooth
This patch adds the device ID for the BCM4343A2 module, found e.g.
in the muRata 1YN WiFi+BT combined device. The required firmware
file is named 'BCM4343A2.hcd'.

Signed-off-by: Marek Vasut <marex@nabladev.com>
Reviewed-by: Paul Menzel <pmenzel@molgen.mpg.de>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
2026-04-10 10:22:21 -04:00
Vivek Sahu
f29bc37dfc Bluetooth: qca: Refactor code on the basis of chipset names
Whenever new chipset support is added to the driver code,
we ended up adding chipset name to the last of the switch case
arising code readability issue because of improper sorting of
the chipset names in various places of the code.

Refactor code such a way that new chipset can be added easily
in the code without compromising code readability.

Signed-off-by: Vivek Sahu <vivek.sahu@oss.qualcomm.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
2026-04-10 10:22:00 -04:00
Chris Lu
679621a767 Bluetooth: btmtk: Add reset mechanism if downloading firmware failed
Add a new flag 'BTMTK_FIRMWARE_DL_RETRY'.
If an error occurs during mt79xx firmware download process, this flag
will be set and cleared after a reset. If the flag is already set and
firmware still cannot be loaded successfully after a reset, no further
reset attempts will be made. In other words, if there is a problem during
firmware download, only one reset will be attempted.

Signed-off-by: Chris Lu <chris.lu@mediatek.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
2026-04-10 10:21:39 -04:00
Chris Lu
b27a306e9f Bluetooth: btmtk: add status check in mt79xx firmware setup
To prevent abnormal controller states, it is necessary to check
status in another part of the mt79xx firmware setup. During this
process, receiving the 'BTMTK_WMT_PATCH_PROGRESS' status is unexpected.
If this occurs, it should be treated as an error, and driver must be
prevented from continuing execution.

Signed-off-by: Chris Lu <chris.lu@mediatek.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
2026-04-10 10:21:19 -04:00
Chris Lu
54f1f020e9 Bluetooth: btmtk: improve mt79xx firmware setup retry flow
If retries are exhausted, driver should not do futher operation.
During mt79xx firmware download process, if the retry count reaches0,
driver will return an -EIO error and release the firmware resources.

Signed-off-by: Chris Lu <chris.lu@mediatek.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
2026-04-10 10:20:39 -04:00
Dongyang Jin
a80b51f066 Bluetooth: btbcm: remove done label in btbcm_patchram
There is no point in having the label since all it does is return the
value in the 'err' variable. Instead make every goto return directly
and remove the label.

Signed-off-by: Dongyang Jin <jindongyang@kylinos.cn>
Reviewed-by: Paul Menzel <pmenzel@molgen.mpg.de>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
2026-04-10 10:20:22 -04:00
Pauli Virtanen
edef657685 Bluetooth: hci_core: Rate limit the logging of invalid ISO handle
Some controller firmwares (eg for MT7925) continuously send invalid ISO
packet, which result to "ISO unknown handle" error spam in logs.  It's
not important to show all of them to the user.

Rate limit these ISO error messages, similarly as we do for SCO.

Signed-off-by: Pauli Virtanen <pav@iki.fi>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
2026-04-10 10:20:04 -04:00
Chris Lu
1f2ac009d3 Bluetooth: btusb: MT7922: Add VID/PID 0489/e174
Add VID 0489 & PID e174 for MediaTek MT7922 USB Bluetooth chip.

The information in /sys/kernel/debug/usb/devices about the Bluetooth
device is listed as the below.

T:  Bus=06 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#=  2 Spd=480  MxCh= 0
D:  Ver= 2.10 Cls=ef(misc ) Sub=02 Prot=01 MxPS=64 #Cfgs=  1
P:  Vendor=0489 ProdID=e174 Rev= 1.00
S:  Manufacturer=MediaTek Inc.
S:  Product=Wireless_Device
S:  SerialNumber=000000000
C:* #Ifs= 3 Cfg#= 1 Atr=e0 MxPwr=100mA
A:  FirstIf#= 0 IfCount= 3 Cls=e0(wlcon) Sub=01 Prot=01
I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=81(I) Atr=03(Int.) MxPS=  16 Ivl=125us
E:  Ad=82(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=   0 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=   0 Ivl=1ms
I:  If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=   9 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=   9 Ivl=1ms
I:  If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=  17 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  17 Ivl=1ms
I:  If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=  25 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  25 Ivl=1ms
I:  If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=  33 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  33 Ivl=1ms
I:  If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=  49 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  49 Ivl=1ms
I:  If#= 1 Alt= 6 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=  63 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  63 Ivl=1ms
I:  If#= 2 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=8a(I) Atr=03(Int.) MxPS=  64 Ivl=125us
E:  Ad=0a(O) Atr=03(Int.) MxPS=  64 Ivl=125us
I:* If#= 2 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=8a(I) Atr=03(Int.) MxPS= 512 Ivl=125us
E:  Ad=0a(O) Atr=03(Int.) MxPS= 512 Ivl=125us

Signed-off-by: Chris Lu <chris.lu@mediatek.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
2026-04-10 10:16:25 -04:00
Hangbin Liu
42f9b4c6ef tools: ynl: tests: fix leading space on Makefile target
The ../generated/protos.a rule had a spurious leading space before the
target name. In make, target rules must start at column 0; only recipe
lines are indented with a tab. The extra space caused make to misparse
the rule.

Remove the leading space to match the style of the adjacent
../lib/ynl.a rule.

Fixes: e0aa0c6175 ("tools: ynl: move samples to tests")
Signed-off-by: Hangbin Liu <liuhangbin@gmail.com>
Link: https://patch.msgid.link/20260408-ynl_makefile-v1-1-f9624acc2ad9@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2026-04-09 20:41:40 -07:00
Jakub Kicinski
3d2c3d2eea selftests: net: py: explicitly forbid multiple ksft_run() calls
People (do people still write code or is it all AI?) seem to not
get that ksft_run() can only be called once. If we call it
multiple times KTAP parsers will likely cut off after the first
batch has finished.

Link: https://patch.msgid.link/20260408221952.819822-1-kuba@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2026-04-09 20:38:33 -07:00
Yue Haibing
3c6132ccc5 ipv6: sit: remove redundant ret = 0 assignment
The variable ret is assigned a value at all places where it is used;
There is no need to assign a value when it is initially defined.

Signed-off-by: Yue Haibing <yuehaibing@huawei.com>
Link: https://patch.msgid.link/20260408032051.3096449-1-yuehaibing@huawei.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2026-04-09 20:37:40 -07:00
Kevin Hao
a17d3c3d0c net: macb: Use napi_schedule_irqoff() in IRQ handler
For non-PREEMPT_RT kernels, the IRQ handler runs with interrupts
disabled, allowing the use of napi_schedule_irqoff() to save a pair of
local_irq_{save,restore} operations. For PREEMPT_RT kernels,
napi_schedule_irqoff() behaves identically to napi_schedule().

Signed-off-by: Kevin Hao <haokexin@gmail.com>
Link: https://patch.msgid.link/20260407-macb-napi-irqoff-v1-1-61bec60047d7@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2026-04-09 20:17:31 -07:00
Qingfang Deng
5ecbebc948 ppp: consolidate refcount decrements
ppp_destroy_{channel,interface} are always called after
refcount_dec_and_test().

To reduce boilerplate code, consolidate the decrements by moving them
into the two functions. To reflect this change in semantics, rename the
functions to ppp_release_*.

Signed-off-by: Qingfang Deng <qingfang.deng@linux.dev>
Link: https://patch.msgid.link/20260407094058.257246-1-qingfang.deng@linux.dev
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2026-04-09 20:03:48 -07:00
Marek Vasut
84c5a3f000 net: phy: realtek: Add property to enable SSC
Add support for spread spectrum clocking (SSC) on RTL8211F(D)(I)-CG,
RTL8211FS(I)(-VS)-CG, RTL8211FG(I)(-VS)-CG PHYs. The implementation
follows EMI improvement application note Rev. 1.2 for these PHYs.

The current implementation enables SSC for both RXC and SYSCLK clock
signals. Introduce DT properties 'realtek,clkout-ssc-enable',
'realtek,rxc-ssc-enable' and 'realtek,sysclk-ssc-enable' which control
CLKOUT, RXC and SYSCLK SSC spread spectrum clocking enablement on these
signals.

Signed-off-by: Marek Vasut <marek.vasut@mailbox.org>
Link: https://patch.msgid.link/20260405233008.148974-3-marek.vasut@mailbox.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2026-04-09 20:01:52 -07:00
Marek Vasut
bfb859a5cb dt-bindings: net: realtek,rtl82xx: Document realtek,*-ssc-enable property
Document support for spread spectrum clocking (SSC) on RTL8211F(D)(I)-CG,
RTL8211FS(I)(-VS)-CG, RTL8211FG(I)(-VS)-CG PHYs. Introduce DT properties
'realtek,clkout-ssc-enable', 'realtek,rxc-ssc-enable' and
'realtek,sysclk-ssc-enable' which control CLKOUT, RXC and SYSCLK
SSC spread spectrum clocking enablement on these signals. These
clock are not exposed via the clock API, therefore assigned-clock-sscs
property does not apply.

Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@oss.qualcomm.com>
Signed-off-by: Marek Vasut <marek.vasut@mailbox.org>
Link: https://patch.msgid.link/20260405233008.148974-2-marek.vasut@mailbox.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2026-04-09 20:01:52 -07:00