Discard granularity tells us the minimum size of extent that can be
discarded by the device. If the user supplies a minimum extent that
should be discarded (range.minlen) which is smaller than the discard
granularity, increase minlen to the discard granularity, since there's
no point submitting trim requests that the device will reject anyway.
Signed-off-by: Lukas Czerner <lczerner@redhat.com>
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
* 'for-linus' of git://oss.sgi.com/xfs/xfs:
xfs: check if device support discard in xfs_ioc_trim()
xfs: prevent leaking uninitialized stack memory in FSGEOMETRY_V1
Fix loop condition in vme_register_bridge that results in an infinite
loop in the event that device_register fails.
Signed-off-by: Manohar Vanga <manohar.vanga@cern.ch>
Acked-by: Martyn Welch <martyn.welch@ge.com>
Acked-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This driver allows any Blackfin system timer to be used as IIO trigger.
It supports trigger rates from 0 to 100kHz in Hz resolution.
Changes since V1:
IIO: trigger: Apply review feedback
Add comment explaining Blackfin hardware timer configurations
Fix frequency_store, don't return -EINVAL for frequency set to 0
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Acked-by: Jonathan Cameron <jic23@cam.ac.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Add support for the AD5543/AD5553 SPI 16-/14-Bit DACs
Fix typo in kconfig description
Changes since V1:
reorder Kconfig help text
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Acked-by: Jonathan Cameron <jic23@cam.ac.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch adds support for the:
AD7606/AD7606-6/AD7606-4 8/6/4-Channel Data Acquisition
system (DAS) with 16-Bit, Bipolar, Simultaneous Sampling ADC.
Changes since V1:
IIO: ADC: New driver for AD7606/AD7606-6/AD7606-4: Apply review feedback
Rename sysfs node oversampling to oversampling_ratio.
Kconfig: Add GPIOLIB dependency.
Use range in mV to better match HWMON.
Rename ad7606_check_oversampling.
Fix various comments and style.
Reorder is_visible cases.
Use new gpio_request_one/array and friends.
Drop check for SPI max_speed_hz.
Changes since V2:
IIO: ADC: New driver for AD7606/AD7606-6/AD7606-4: Apply review feedback
Documentation: specify unit
Avoid raise condition in ad7606_scan_direct()
Check return value of bus ops read_block()
Changes since V3:
IIO: ADC: New driver for AD7606/AD7606-6/AD7606-4: Add missing include file
Add linux/sched.h
Changes since V4:
IIO: ADC: New driver for AD7606/AD7606-6/AD7606-4: Fix kconfig declaration
consistently use tristate to avoid configuration mismatches
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Acked-by: Jonathan Cameron <jic23@cam.ac.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This is the bluetooth protocol driver for the TI WiLink7 chipsets.
Texas Instrument's WiLink chipsets combine wireless technologies
like BT, FM, GPS and WLAN onto a single chip.
This Bluetooth driver works on top of the TI_ST shared transport
line discipline driver which also allows other drivers like
FM V4L2 and GPS character driver to make use of the same UART interface.
Kconfig and Makefile modifications to enable the Bluetooth
driver for Texas Instrument's WiLink 7 chipset.
Signed-off-by: Pavan Savoy <pavan_savoy@ti.com>
Acked-by: Gustavo F. Padovan <padovan@profusion.mobi>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The cur_item variable from keyhelp.c is an index into a table of
messages. The following condition should always hold:
MSG_FUNCNAMES_START + cur_item <= MSG_FUNCNAMES_END.
The check in keyhelp.c was wrong. It allowed cur_item to be
incremented to an out-of-bounds value.
Signed-off-by: Christopher Brannon <chris@the-brannons.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Commit 1bd751c1ab
("Staging: et131x: Clean up rxdma_csr") changed csr from bitfield to
u32, but failed to convert 2 uses of halt_status bit. It did:
- if (csr.bits.halt_status != 1)
+ if ((csr & 0x00020000) != 1)
which is wrong, because second version is always true.
Fix it.
This bug was found by coccinelle (http://coccinelle.lip6.fr/).
Signed-off-by: Marcin Slusarz <marcin.slusarz@gmail.com>
Acked-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The device is very similar to (0x0fe6, 0x8101),
And works well with dm9601 driver.
Signed-off-by: Shahar Havivi <shaharh@redhat.com>
Acked-by: Peter Korsgaard <jacmet@sunsite.dk>
Signed-off-by: David S. Miller <davem@davemloft.net>
- fix the RTL8111DP turn off the power when DASH is enabled.
- RTL_GIGA_MAC_VER_27 must wait for tx finish before reset.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Acked-by: Francois Romieu <romieu@fr.zoreil.com>
Adjust and remove certain settings of RTL8102E which are for previous chips.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Acked-off-by: Francois Romieu <romieu@fr.zoreil.com>
It results in the wrong point address and influences RTL8168DP.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Acked-by: Francois Romieu <romieu@fr.zoreil.com>
DM9000 revision B needs 1 ms delay after PHY power-on.
PHY must be powered on by writing 0 into register DM9000_GPR before
all other settings will change (see Davicom spec and example code).
Remember, that register DM9000_GPR was not changed by reset sequence.
Without this fix the FIFO is out of sync and sends wrong data after
sequence of "ifconfig ethX down ; ifconfig ethX up".
Signed-off-by: David S. Miller <davem@davemloft.net>
Max rx queues and tx queues are governed by fimware.
So driver should not validate these values.
Signed-off-by: Rajesh Borundia <rajesh.borundia@qlogic.com>
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
o Remove checks of 1 for auto_fw_reset module parameter.
auto_fw_reset is of type int and can have value > 1.
o Remove unnecessary #define for 1
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use discrete setting ops for not updated drivers. This will not make
them conform to full G/SFEATURES semantics, though.
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implement getting rx checksum state for not updated drivers.
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>
Avoid "Features changed" message and ndo_set_features call on device
registration caused by automatic enabling of GSO and GRO. Driver should
have enabled hardware offloads it set in features, so the ndo_set_features()
is not needed at registration time.
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix netdev_update_features() messages on register time by moving
the call further in register_netdevice(). When
netdev->reg_state != NETREG_REGISTERED, netdev_name() returns
"(unregistered netdevice)" even if the dev's name is already filled.
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>
The original code does not work well when the number of mulitcast
address to handle is greater than MCAST_MAX. It only enable promiscous
mode instead of multicast hash table mode, so the hash table function
will not be activated and all multicast frames will be recieved in this
condition.
This patch fixes the following issues with the r6040 NIC operating in
multicast:
1) When the IFF_ALLMULTI flag is set, we should write 0xffff to the NIC
hash table registers to make it process multicast traffic.
2) When the number of multicast address to handle is smaller than
MCAST_MAX, we should use the NIC multicast registers MID1_{L,M,H}.
3) The hashing of the address was not correct, due to an invalid
substraction (15 - (crc & 0x0f)) instead of (crc & 0x0f) and an
incorrect crc algorithm (ether_crc_le) instead of (ether_crc).
4) If necessary, we should set HASH_EN flag in MCR0 to enable multicast
hash table function.
Reported-by: Marc Leclerc <marc-leclerc@signaturealpha.com>
Tested-by: Marc Leclerc <marc-leclerc@signaturealpha.com>
Signed-off-by: Shawn Lin <shawn@dmp.com.tw>
Signed-off-by: Albert Chen <albert.chen@rdc.com.tw>
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
pSR and pCR fields can be deleted with no changes in the functionality.
Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Delete dead code for skipping the video memory sizing.
Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Due a cleanup in earlier patches, the function fbcon_XGI_sync now does nothing
so it has to be removed.
This patches removes the unused function.
Signed-off-by: Javier Martinez Canillas <martinez.javier@gmail.com>
Acked-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
xgifb framebuffer driver had an option to use an accelerator engine that never
got used (XGIfb_accel was always 0).
An earlier patchset removed the code relevant to the accelerator.
Since this spinlock was used only for that code, it can be deleted as well.
Signed-off-by: Javier Martinez Canillas <martinez.javier@gmail.com>
Acked-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
xgifb framebuffer driver has an option to use an accelerator engine that never
get used (XGIfb_accel is always 0).
An earlier patchset remove the code that depends on the accelerator being
activated. This patch removes all the references to XGIfb_accel.
Signed-off-by: Javier Martinez Canillas <martinez.javier@gmail.com>
Acked-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
xgifb staging driver for XG20, XG21, XG40, XG42 frame buffer device
has a accelerator engine that never get used (XGIfb_accel is always 0).
Also the driver has a set of defines that hides the synchronization
mechanism used to access critical sections and a way to disable spinlocks
use at compile time.
In a earlier patch all the code that depends on the accelerator being active
was deleted because it was dead code. Since the only usage of this
synchronization defines were in that dead code, this patch removes all the
now unused spinlock conditional compilation logic.
Signed-off-by: Javier Martinez Canillas <martinez.javier@gmail.com>
Acked-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Earlier patch removed code that never got executed because it depended on
XGIfb_accel variable value to de distinct than 0. But this variable is
always 0 in current driver.
That dead code used a set of functions that not remains unused.
This patch removes these unused functions.
Signed-off-by: Javier Martinez Canillas <martinez.javier@gmail.com>
Acked-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
xgifb staging driver has code that dependens on XGIfb_accel != 0.
But as Dan Carpenter noticed, XGIfb_accel value is always 0 in current driver.
So there is code that never gets executed.
This patch removes this dead code.
Signed-off-by: Javier Martinez Canillas <martinez.javier@gmail.com>
Acked-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
netem_skb_cb() does :
return (struct netem_skb_cb *)qdisc_skb_cb(skb)->data;
Unfortunatly struct qdisc_skb_cb data is not long word aligned, so
access to psched_time_t time_to_send uses a non aligned access.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
use USB_SUBCLASS_AUDIOSTREAMING constant from usb/audio.h
instead of 0x02
Cc: Mike Thomas <rmthomas@sciolus.org>
Cc: Dan Carpenter <error27@gmail.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Cc: Mike Thomas <rmthomas@sciolus.org>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Reviewed-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
make inputset population to be more compact and readable
Cc: Mike Thomas <rmthomas@sciolus.org>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Reviewed-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
fix some code styles and drop too verbose printouts
and non relevant code
Cc: Mike Thomas <rmthomas@sciolus.org>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Reviewed-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This reverts commit f2f1794835.
It should not be putting code into the include/input/ directory, and
lots of other people have complained about it.
Cc: Tony SIM <chinyeow.sim.xt@renesas.com>
Cc: Andrew Chew <achew@nvidia.com>
Cc: Jonathan Cameron <jic23@cam.ac.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* make qdisc_ops local
* add sparse annotation about expected unlock/unlock in dump_class_stats
* fix indentation
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The dmaw_block is an enum and max_pay_load is u32. Therefore
sparse gives warning about comparison of unsigned and signed value.
Resolve by using min_t to force cast.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use __force to quiet sparse warnings for cases where the code
is simulating user space pointers.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>