commit fec40f44af upstream.
SPI mode doesn't support cmd7, so remove it in mmc_sdio_alive() and
confirm if sdio is active by checking CCCR register value is available
or not.
Signed-off-by: Rex Chen <rex.chen_1@nxp.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20250728082230.1037917-2-rex.chen_1@nxp.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1001cc1171 upstream.
Commit f04ced6d54 ("mtd: nand: raw: gpmi: improve power management
handling") moved all clock handling into PM callbacks. With CONFIG_PM
disabled, those callbacks are missing, leaving the driver unusable.
Add clock init/teardown for !CONFIG_PM builds to restore basic operation.
Keeping the driver working without requiring CONFIG_PM is preferred over
adding a Kconfig dependency.
Fixes: f04ced6d54 ("mtd: nand: raw: gpmi: improve power management handling")
Signed-off-by: Maarten Zanders <maarten@zanders.be>
Cc: stable@vger.kernel.org
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 07ca98f906 upstream.
Turned out certain clearly invalid values passed in xdp_desc from
userspace can pass xp_{,un}aligned_validate_desc() and then lead
to UBs or just invalid frames to be queued for xmit.
desc->len close to ``U32_MAX`` with a non-zero pool->tx_metadata_len
can cause positive integer overflow and wraparound, the same way low
enough desc->addr with a non-zero pool->tx_metadata_len can cause
negative integer overflow. Both scenarios can then pass the
validation successfully.
This doesn't happen with valid XSk applications, but can be used
to perform attacks.
Always promote desc->len to ``u64`` first to exclude positive
overflows of it. Use explicit check_{add,sub}_overflow() when
validating desc->addr (which is ``u64`` already).
bloat-o-meter reports a little growth of the code size:
add/remove: 0/0 grow/shrink: 2/1 up/down: 60/-16 (44)
Function old new delta
xskq_cons_peek_desc 299 330 +31
xsk_tx_peek_release_desc_batch 973 1002 +29
xsk_generic_xmit 3148 3132 -16
but hopefully this doesn't hurt the performance much.
Fixes: 341ac980ea ("xsk: Support tx_metadata_len")
Cc: stable@vger.kernel.org # 6.8+
Signed-off-by: Alexander Lobakin <aleksander.lobakin@intel.com>
Reviewed-by: Jason Xing <kerneljasonxing@gmail.com>
Reviewed-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Link: https://lore.kernel.org/r/20251008165659.4141318-1-aleksander.lobakin@intel.com
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5d5f08fd0c upstream.
A malicious user could pass an arbitrarily bad value
to memdup_user_nul(), potentially causing kernel crash.
This follows the same pattern as commit ee76746387
("netdevsim: prevent bad user input in nsim_dev_health_break_write()")
Fixes: b6c7e873da ("xtensa: ISS: add host file-based simulated disk")
Fixes: 16e5c1fc36 ("convert a bunch of open-coded instances of memdup_user_nul()")
Cc: stable@vger.kernel.org
Signed-off-by: Miaoqian Lin <linmq006@gmail.com>
Message-Id: <20250829083015.1992751-1-linmq006@gmail.com>
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 302c04110f upstream.
Once of_device_register() failed, we should call put_device() to
decrement reference count for cleanup. Or it could cause memory leak.
So fix this by calling put_device(), then the name can be freed in
kobject_cleanup().
Calling path: of_device_register() -> of_device_add() -> device_add().
As comment of device_add() says, 'if device_add() succeeds, you should
call device_del() when you want to get rid of it. If device_add() has
not succeeded, use only put_device() to drop the reference count'.
Found by code review.
Cc: stable@vger.kernel.org
Fixes: cf44bbc26c ("[SPARC]: Beginnings of generic of_device framework.")
Signed-off-by: Ma Ke <make24@iscas.ac.cn>
Reviewed-by: Andreas Larsson <andreas@gaisler.com>
Signed-off-by: Andreas Larsson <andreas@gaisler.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6fd44a481b upstream.
An attempt to exercise sparc hugetlb code in a sun4u-based guest
running under qemu results in the guest hanging due to being stuck
in a trap loop. This is due to invalid hugetlb TTEs being installed
that do not have the expected _PAGE_PMD_HUGE and page size bits set.
Although the breakage has gone apparently unnoticed for several years,
fix it now so there is the option to exercise sparc hugetlb code under
qemu. This can be useful because sun4v support in qemu does not support
linux guests currently and sun4v-based hardware resources may not be
readily available.
Fix tested with a 6.15.2 and 6.16-rc6 kernels by running libhugetlbfs
tests on a qemu guest running Debian 13.
Fixes: c7d9f77d33 ("sparc64: Multi-page size support")
Cc: stable@vger.kernel.org
Signed-off-by: Anthony Yznaga <anthony.yznaga@oracle.com>
Tested-by: John Paul Adrian Glaubitz <glaubitz@physik.fu-berlin.de>
Reviewed-by: John Paul Adrian Glaubitz <glaubitz@physik.fu-berlin.de>
Reviewed-by: Andreas Larsson <andreas@gaisler.com>
Link: https://lore.kernel.org/r/20250716012446.10357-1-anthony.yznaga@oracle.com
Signed-off-by: Andreas Larsson <andreas@gaisler.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit aa12118dbc upstream.
Test generic/637 spotted a problem with create of a new file in a
cached directory (by the same client) could cause cases where the
new file does not show up properly in ls on that client until the
lease times out.
Fixes: 037e1bae58 ("smb: client: use ParentLeaseKey in cifs_do_create")
Cc: stable@vger.kernel.org
Signed-off-by: Bharath SM <bharathsm@microsoft.com>
Signed-off-by: Steve French <stfrench@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit dd91c79e4f upstream.
To prevent timing attacks, MACs need to be compared in constant time.
Use the appropriate helper function for this.
Fixes: bbd0d59809 ("[SCTP]: Implement the receive and verification of AUTH chunk")
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Cc: stable@vger.kernel.org
Signed-off-by: Eric Biggers <ebiggers@kernel.org>
Link: https://patch.msgid.link/20250818205426.30222-3-ebiggers@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b5f717b31b upstream.
A build warning was triggered due to excessive stack usage in
sd_revalidate_disk():
drivers/scsi/sd.c: In function ‘sd_revalidate_disk.isra’:
drivers/scsi/sd.c:3824:1: warning: the frame size of 1160 bytes is larger than 1024 bytes [-Wframe-larger-than=]
This is caused by a large local struct queue_limits (~400B) allocated on
the stack. Replacing it with a heap allocation using kmalloc()
significantly reduces frame usage. Kernel stack is limited (~8 KB), and
allocating large structs on the stack is discouraged. As the function
already performs heap allocations (e.g. for buffer), this change fits
well.
Fixes: 804e498e04 ("sd: convert to the atomic queue limits API")
Cc: stable@vger.kernel.org
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Abinash Singh <abinashsinghlalotra@gmail.com>
Link: https://lore.kernel.org/r/20250825183940.13211-2-abinashsinghlalotra@gmail.com
Reviewed-by: Damien Le Moal <dlemoal@kernel.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b81296591c upstream.
Replace kmalloc() followed by copy_from_user() with memdup_user() to fix
a memory leak that occurs when copy_from_user(buff[sg_used],,) fails and
the 'cleanup1:' path does not free the memory for 'buff[sg_used]'. Using
memdup_user() avoids this by freeing the memory internally.
Since memdup_user() already allocates memory, use kzalloc() in the else
branch instead of manually zeroing 'buff[sg_used]' using memset(0).
Cc: stable@vger.kernel.org
Fixes: edd163687e ("[SCSI] hpsa: add driver for HP Smart Array controllers.")
Signed-off-by: Thorsten Blum <thorsten.blum@linux.dev>
Acked-by: Don Brace <don.brace@microchip.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8fd5485fb4 upstream.
When a CPU chooses to call push_dl_task and picks a task to push to
another CPU's runqueue then it will call find_lock_later_rq method
which would take a double lock on both CPUs' runqueues. If one of the
locks aren't readily available, it may lead to dropping the current
runqueue lock and reacquiring both the locks at once. During this window
it is possible that the task is already migrated and is running on some
other CPU. These cases are already handled. However, if the task is
migrated and has already been executed and another CPU is now trying to
wake it up (ttwu) such that it is queued again on the runqeue
(on_rq is 1) and also if the task was run by the same CPU, then the
current checks will pass even though the task was migrated out and is no
longer in the pushable tasks list.
Please go through the original rt change for more details on the issue.
To fix this, after the lock is obtained inside the find_lock_later_rq,
it ensures that the task is still at the head of pushable tasks list.
Also removed some checks that are no longer needed with the addition of
this new check.
However, the new check of pushable tasks list only applies when
find_lock_later_rq is called by push_dl_task. For the other caller i.e.
dl_task_offline_migration, existing checks are used.
Signed-off-by: Harshit Agarwal <harshit@nutanix.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Acked-by: Juri Lelli <juri.lelli@redhat.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20250408045021.3283624-1-harshit@nutanix.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5d09ee1bec upstream.
This reverts commit c608966f3f.
This patch has a subtle bug that can cause the IPMI driver to go into an
infinite loop if the BMC misbehaves in a certain way. Apparently
certain BMCs do misbehave this way because several reports have come in
recently about this.
Signed-off-by: Corey Minyard <corey@minyard.net>
Tested-by: Eric Hagberg <ehagberg@janestreet.com>
Cc: <stable@vger.kernel.org> # 6.2
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit afe872274e upstream.
The dev_err message is reporting the incorrect return value ret_tohw,
it should be reporting the value in ret_fromhw. Fix this by using
ret_fromhw instead of ret_tohw.
Fixes: 6c5126c640 ("pwm: Provide new consumer API functions for waveforms")
Signed-off-by: Colin Ian King <colin.i.king@gmail.com>
Link: https://lore.kernel.org/r/20250902130348.2630053-1-colin.i.king@gmail.com
Cc: stable@vger.kernel.org
Signed-off-by: Uwe Kleine-König <ukleinek@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3a4b9d027e upstream.
The 'enable' register should be BERLIN_PWM_EN rather than
BERLIN_PWM_ENABLE, otherwise, the driver accesses wrong address, there
will be cpu exception then kernel panic during suspend/resume.
Fixes: bbf0722c1c ("pwm: berlin: Add suspend/resume support")
Signed-off-by: Jisheng Zhang <jszhang@kernel.org>
Link: https://lore.kernel.org/r/20250819114224.31825-1-jszhang@kernel.org
Cc: stable@vger.kernel.org
Signed-off-by: Uwe Kleine-König <ukleinek@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3443ff3be6 upstream.
pseries_irq_domain_alloc() allocates interrupts at parent's interrupt
domain. If it fails in the progress, all allocated interrupts are
freed.
The number of successfully allocated interrupts so far is stored
"i". However, "i - 1" interrupts are freed. This is broken:
- One interrupt is not be freed
- If "i" is zero, "i - 1" wraps around
Correct the number of freed interrupts to 'i'.
Fixes: a5f3d2c17b ("powerpc/pseries/pci: Add MSI domains")
Signed-off-by: Nam Cao <namcao@linutronix.de>
Cc: stable@vger.kernel.org
Reviewed-by: Cédric Le Goater <clg@redhat.com>
Signed-off-by: Madhavan Srinivasan <maddy@linux.ibm.com>
Link: https://patch.msgid.link/a980067f2b256bf716b4cd713bc1095966eed8cd.1754300646.git.namcao@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a39087905a upstream.
pnv_irq_domain_alloc() allocates interrupts at parent's interrupt
domain. If it fails in the progress, all allocated interrupts are
freed.
The number of successfully allocated interrupts so far is stored
"i". However, "i - 1" interrupts are freed. This is broken:
- One interrupt is not be freed
- If "i" is zero, "i - 1" wraps around
Correct the number of freed interrupts to "i".
Fixes: 0fcfe2247e ("powerpc/powernv/pci: Add MSI domains")
Signed-off-by: Nam Cao <namcao@linutronix.de>
Cc: stable@vger.kernel.org
Reviewed-by: Cédric Le Goater <clg@redhat.com>
Signed-off-by: Madhavan Srinivasan <maddy@linux.ibm.com>
Link: https://patch.msgid.link/70f8debe8688e0b467367db769b71c20146a836d.1754300646.git.namcao@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ee6cd8f3e2 upstream.
CHARGE_CONTROL_LIMIT is a wrong property to report charge current limit,
because `CHARGE_*` attributes represents capacity, not current. The
correct attribute to report and set charge current limit is
CONSTANT_CHARGE_CURRENT.
Rename CHARGE_CONTROL_LIMIT to CONSTANT_CHARGE_CURRENT.
Cc: stable@vger.kernel.org
Fixes: 715ecbc10d ("power: supply: max77976: add Maxim MAX77976 charger driver")
Signed-off-by: Dzmitry Sankouski <dsankouski@gmail.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6f4c6f9ed4 upstream.
Commit 12ffc3b151 ("PM: Restrict swap use to later in the
suspend sequence") caused hibernation_platform_enter() to call
pm_restore_gfp_mask() via dpm_resume_end(), so when power_down()
returns after aborting hibernation_platform_enter(), it needs
to match the pm_restore_gfp_mask() call in hibernate() that will
occur subsequently.
Address this by adding a pm_restrict_gfp_mask() call to the relevant
error path in power_down().
Fixes: 12ffc3b151 ("PM: Restrict swap use to later in the suspend sequence")
Cc: 6.16+ <stable@vger.kernel.org> # 6.16+
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Mario Limonciello (AMD) <superm1@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 469d80a371 upstream.
Hybrid sleep will hibernate the system followed by running through
the suspend routine. Since both the hibernate and the suspend routine
will call pm_restrict_gfp_mask(), pm_restore_gfp_mask() must be called
before starting the suspend sequence.
Add an explicit call to pm_restore_gfp_mask() to power_down() before
the suspend sequence starts. Add an extra call for pm_restrict_gfp_mask()
when exiting suspend so that the pm_restore_gfp_mask() call in hibernate()
is balanced.
Reported-by: Ionut Nechita <ionut_n2001@yahoo.com>
Closes: https://gitlab.freedesktop.org/drm/amd/-/issues/4573
Tested-by: Ionut Nechita <ionut_n2001@yahoo.com>
Fixes: 12ffc3b151 ("PM: Restrict swap use to later in the suspend sequence")
Tested-by: Kenneth Crudup <kenny@panix.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Mario Limonciello (AMD) <superm1@kernel.org>
Link: https://patch.msgid.link/20250925185108.2968494-2-superm1@kernel.org
[ rjw: Add comment explainig the new pm_restrict_gfp_mask() call purpose ]
Cc: 6.16+ <stable@vger.kernel.org> # 6.16+
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1ebe8f7e78 upstream.
Commit e3f1164fc9 ("PM: EM: Support late CPUs booting and capacity
adjustment") added a mechanism to handle CPUs that come up late by
retrying when any of the `cpufreq_cpu_get()` call fails.
However, if there are holes in the CPU topology (offline CPUs, e.g.
nosmt), the first missing CPU causes the loop to break, preventing
subsequent online CPUs from being updated.
Instead of aborting on the first missing CPU policy, loop through all
and retry if any were missing.
Fixes: e3f1164fc9 ("PM: EM: Support late CPUs booting and capacity adjustment")
Suggested-by: Kenneth Crudup <kenneth.crudup@gmail.com>
Reported-by: Kenneth Crudup <kenneth.crudup@gmail.com>
Link: https://lore.kernel.org/linux-pm/40212796-734c-4140-8a85-854f72b8144d@panix.com/
Cc: 6.9+ <stable@vger.kernel.org> # 6.9+
Signed-off-by: Christian Loehle <christian.loehle@arm.com>
Link: https://patch.msgid.link/20250831214357.2020076-1-christian.loehle@arm.com
[ rjw: Drop the new pr_debug() message which is not very useful ]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit eeaed48980 upstream.
On the TUXEDO InfinityBook S Gen8, a Samsung 990 Evo NVMe leads to
a high power consumption in s2idle sleep (3.5 watts).
This patch applies 'Force No Simple Suspend' quirk to achieve a sleep with
a lower power consumption, typically around 1 watts.
Signed-off-by: Georg Gottleuber <ggo@tuxedocomputers.com>
Signed-off-by: Werner Sembach <wse@tuxedocomputers.com>
Cc: stable@vger.kernel.org
Signed-off-by: Keith Busch <kbusch@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 16794e524d upstream.
Accidently introduced in commit 91428ca932.
Signed-off-by: John David Anglin <dave.anglin@bell.net>
Signed-off-by: Helge Deller <deller@gmx.de>
Fixes: 91428ca932 ("parisc: Check region is readable by user in raw_copy_from_user()")
Cc: stable@vger.kernel.org # v5.12+
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8ec5a066f8 upstream.
Similar in nature to ab10727660. glibc-2.42
drops the legacy termio struct, but the ioctls.h header still defines some
TC* constants in terms of termio (via sizeof). Hardcode the values instead.
This fixes building Python for example, which falls over like:
./Modules/termios.c:1119:16: error: invalid application of 'sizeof' to incomplete type 'struct termio'
Link: https://bugs.gentoo.org/961769
Link: https://bugs.gentoo.org/962600
Co-authored-by: Stian Halseth <stian@itx.no>
Cc: stable@vger.kernel.org
Signed-off-by: Sam James <sam@gentoo.org>
Signed-off-by: Helge Deller <deller@gmx.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 501302d5ce upstream.
When seq_nr wraps around, the next reorder job with seq 0 is hashed to
the first CPU in padata_do_serial(). Correspondingly, need reset pd->cpu
to the first one when pd->processed wraps around. Otherwise, if the
number of used CPUs is not a power of 2, padata_find_next() will be
checking a wrong list, hence deadlock.
Fixes: 6fc4dbcf02 ("padata: Replace delayed timer with immediate workqueue in padata_reorder")
Cc: <stable@vger.kernel.org>
Signed-off-by: Xiao Liang <shaw.leon@gmail.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a8de554774 upstream.
In of_unittest_pci_node_verify(), when the add parameter is false,
device_find_any_child() obtains a reference to a child device. This
function implicitly calls get_device() to increment the device's
reference count before returning the pointer. However, the caller
fails to properly release this reference by calling put_device(),
leading to a device reference count leak. Add put_device() in the else
branch immediately after child_dev is no longer needed.
As the comment of device_find_any_child states: "NOTE: you will need
to drop the reference with put_device() after use".
Found by code review.
Cc: stable@vger.kernel.org
Fixes: 26409dd045 ("of: unittest: Add pci_dt_testdrv pci driver")
Signed-off-by: Ma Ke <make24@iscas.ac.cn>
Signed-off-by: Rob Herring (Arm) <robh@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 22f166218f upstream.
If bio is split by internal handling like chunksize or badblocks, the
corresponding trace_block_split() is missing, resulting in blktrace
inability to catch BIO split events and making it harder to analyze the
BIO sequence.
Cc: stable@vger.kernel.org
Fixes: 4b1faf9316 ("block: Kill bio_pair_split()")
Signed-off-by: Yu Kuai <yukuai3@huawei.com>
Reviewed-by: Damien Le Moal <dlemoal@kernel.org>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 98b7bf5433 upstream.
loop_change_fd() and loop_configure() call loop_check_backing_file()
to validate the new backing file. If validation fails, the reference
acquired by fget() was not dropped, leaking a file reference.
Fix this by calling fput(file) before returning the error.
Cc: stable@vger.kernel.org
Cc: Markus Elfring <Markus.Elfring@web.de>
CC: Yang Erkun <yangerkun@huawei.com>
Cc: Ming Lei <ming.lei@redhat.com>
Cc: Yu Kuai <yukuai1@huaweicloud.com>
Fixes: f5c84eff63 ("loop: Add sanity check for read/write_iter")
Signed-off-by: Li Chen <chenl311@chinatelecom.cn>
Reviewed-by: Ming Lei <ming.lei@redhat.com>
Reviewed-by: Yang Erkun <yangerkun@huawei.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1260cbcffa upstream.
Make sure to drop the reference taken when looking up the genpool platform
device in of_gen_pool_get() before returning the pool.
Note that holding a reference to a device does typically not prevent its
devres managed resources from being released so there is no point in
keeping the reference.
Link: https://lkml.kernel.org/r/20250924080207.18006-1-johan@kernel.org
Fixes: 9375db07ad ("genalloc: add devres support, allow to find a managed pool by device")
Signed-off-by: Johan Hovold <johan@kernel.org>
Cc: Philipp Zabel <p.zabel@pengutronix.de>
Cc: Vladimir Zapolskiy <vz@mleia.com>
Cc: <stable@vger.kernel.org> [3.10+]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f322a97aeb upstream.
kho_fill_kimage() only checks for KHO being enabled before filling in the
FDT to the image. KHO being enabled does not mean that the kernel has
data to hand over. That happens when KHO is finalized.
When a kexec is done with KHO enabled but not finalized, the FDT page is
allocated but not initialized. FDT initialization happens after finalize.
This means the KHO segment is filled in but the FDT contains garbage
data.
This leads to the below error messages in the next kernel:
[ 0.000000] KHO: setup: handover FDT (0x10116b000) is invalid: -9
[ 0.000000] KHO: disabling KHO revival: -22
There is no problem in practice, and the next kernel boots and works fine.
But this still leads to misleading error messages and garbage being
handed over.
Only fill in KHO segment when KHO is finalized. When KHO is not enabled,
the debugfs interface is not created and there is no way to finalize it
anyway. So the check for kho_enable is not needed, and kho_out.finalize
alone is enough.
Link: https://lkml.kernel.org/r/20250918170617.91413-1-pratyush@kernel.org
Fixes: 3bdecc3c93 ("kexec: add KHO support to kexec file loads")
Signed-off-by: Pratyush Yadav <pratyush@kernel.org>
Reviewed-by: Mike Rapoport (Microsoft) <rppt@kernel.org>
Cc: Alexander Graf <graf@amazon.com>
Cc: Baoquan He <bhe@redhat.com>
Cc: Changyuan Lyu <changyuanl@google.com>
Cc: Jason Gunthorpe <jgg@nvidia.com>
Cc: Pasha Tatashin <pasha.tatashin@soleen.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit eed0e3d305 upstream.
To prevent timing attacks, HMAC value comparison needs to be constant
time. Replace the memcmp() with the correct function, crypto_memneq().
[For the Fixes commit I used the commit that introduced the memcmp().
It predates the introduction of crypto_memneq(), but it was still a bug
at the time even though a helper function didn't exist yet.]
Fixes: d00a1c72f7 ("keys: add new trusted key-type")
Cc: stable@vger.kernel.org
Signed-off-by: Eric Biggers <ebiggers@kernel.org>
Reviewed-by: Jarkko Sakkinen <jarkko@kernel.org>
Signed-off-by: Jarkko Sakkinen <jarkko@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a15f37a401 upstream.
The usage of task_lock(tsk->group_leader) in sys_prlimit64()->do_prlimit()
path is very broken.
sys_prlimit64() does get_task_struct(tsk) but this only protects task_struct
itself. If tsk != current and tsk is not a leader, this process can exit/exec
and task_lock(tsk->group_leader) may use the already freed task_struct.
Another problem is that sys_prlimit64() can race with mt-exec which changes
->group_leader. In this case do_prlimit() may take the wrong lock, or (worse)
->group_leader may change between task_lock() and task_unlock().
Change sys_prlimit64() to take tasklist_lock when necessary. This is not
nice, but I don't see a better fix for -stable.
Link: https://lkml.kernel.org/r/20250915120917.GA27702@redhat.com
Fixes: 18c91bb2d8 ("prlimit: do not grab the tasklist_lock")
Signed-off-by: Oleg Nesterov <oleg@redhat.com>
Cc: Christian Brauner <brauner@kernel.org>
Cc: Jiri Slaby <jirislaby@kernel.org>
Cc: Mateusz Guzik <mjguzik@gmail.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8fd8ea2869 upstream.
Dan Carpenter got a Smatch warning:
drivers/char/ipmi/ipmi_msghandler.c:5265 ipmi_free_recv_msg()
warn: sleeping in atomic context
due to the recent rework of the IPMI driver's locking. I didn't realize
vfree could block. But there is an easy solution to this, now that
almost everything in the message handler runs in thread context.
I wanted to spend the time earlier to see if seq_lock could be converted
from a spinlock to a mutex, but I wanted the previous changes to go in
and soak before I did that. So I went ahead and did the analysis and
converting should work. And solve this problem.
Reported-by: kernel test robot <lkp@intel.com>
Reported-by: Dan Carpenter <dan.carpenter@linaro.org>
Closes: https://lore.kernel.org/r/202503240244.LR7pOwyr-lkp@intel.com/
Fixes: 3be997d5a6 ("ipmi:msghandler: Remove srcu from the ipmi user structure")
Cc: <stable@vger.kernel.org> # 6.16
Signed-off-by: Corey Minyard <corey@minyard.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b52da4054e upstream.
The limit on the number of user messages had a number of issues,
improper counting in some cases and a use after free.
Restructure how this is all done to handle more in the receive message
allocation routine, so all refcouting and user message limit counts
are done in that routine. It's a lot cleaner and safer.
Reported-by: Gilles BULOZ <gilles.buloz@kontron.com>
Closes: https://lore.kernel.org/lkml/aLsw6G0GyqfpKs2S@mail.minyard.net/
Fixes: 8e76741c3d ("ipmi: Add a limit on the number of users that may use IPMI")
Cc: <stable@vger.kernel.org> # 4.19
Signed-off-by: Corey Minyard <corey@minyard.net>
Tested-by: Gilles BULOZ <gilles.buloz@kontron.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5ef7e24c74 upstream.
The specification, Section 7.10, "Software Steps to Drain Page Requests &
Responses," requires software to submit an Invalidation Wait Descriptor
(inv_wait_dsc) with the Page-request Drain (PD=1) flag set, along with
the Invalidation Wait Completion Status Write flag (SW=1). It then waits
for the Invalidation Wait Descriptor's completion.
However, the PD field in the Invalidation Wait Descriptor is optional, as
stated in Section 6.5.2.9, "Invalidation Wait Descriptor":
"Page-request Drain (PD): Remapping hardware implementations reporting
Page-request draining as not supported (PDS = 0 in ECAP_REG) treat this
field as reserved."
This implies that if the IOMMU doesn't support the PDS capability, software
can't drain page requests and group responses as expected.
Do not enable PCI/PRI if the IOMMU doesn't support PDS.
Reported-by: Joel Granados <joel.granados@kernel.org>
Closes: https://lore.kernel.org/r/20250909-jag-pds-v1-1-ad8cba0e494e@kernel.org
Fixes: 66ac4db36f ("iommu/vt-d: Add page request draining support")
Cc: stable@vger.kernel.org
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Link: https://lore.kernel.org/r/20250915062946.120196-1-baolu.lu@linux.intel.com
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 466f7a2fef upstream.
Do as in suspend, skip resume configuration steps if the device is already
pm_runtime suspended. This avoids reconfiguring a device that is already
in the correct low-power state and ensures that pm_runtime handles the
power state transitions properly.
Fixes: 31c24c1e93 ("iio: imu: inv_icm42600: add core of new inv_icm42600 driver")
Signed-off-by: Sean Nyekjaer <sean@geanix.com>
Link: https://patch.msgid.link/20250901-icm42pmreg-v3-3-ef1336246960@geanix.com
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a95a0b4e47 upstream.
Remove unnecessary calls to pm_runtime_disable(), pm_runtime_set_active(),
and pm_runtime_enable() from the resume path. These operations are not
required here and can interfere with proper pm_runtime state handling,
especially when resuming from a pm_runtime suspended state.
Fixes: 31c24c1e93 ("iio: imu: inv_icm42600: add core of new inv_icm42600 driver")
Signed-off-by: Sean Nyekjaer <sean@geanix.com>
Link: https://patch.msgid.link/20250901-icm42pmreg-v3-2-ef1336246960@geanix.com
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0792c1984a upstream.
Rework the power management in inv_icm42600_core_probe() to use
devm_pm_runtime_set_active_enabled(), which simplifies the runtime PM
setup by handling activation and enabling in one step.
Remove the separate inv_icm42600_disable_pm callback, as it's no longer
needed with the devm-managed approach.
Using devm_pm_runtime_enable() also fixes the missing disable of
autosuspend.
Update inv_icm42600_disable_vddio_reg() to only disable the regulator if
the device is not suspended i.e. powered-down, preventing unbalanced
disables.
Also remove redundant error msg on regulator_disable(), the regulator
framework already emits an error message when regulator_disable() fails.
This simplifies the PM setup and avoids manipulating the usage counter
unnecessarily.
Fixes: 31c24c1e93 ("iio: imu: inv_icm42600: add core of new inv_icm42600 driver")
Signed-off-by: Sean Nyekjaer <sean@geanix.com>
Link: https://patch.msgid.link/20250901-icm42pmreg-v3-1-ef1336246960@geanix.com
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e416f0ed3c upstream.
BootLoaders (Grub, LILO, etc) may pass an identifier such as "BOOT_IMAGE=
/boot/vmlinuz-x.y.z" to kernel parameters. But these identifiers are not
recognized by the kernel itself so will be passed to userspace. However
user space init program also don't recognize it.
KEXEC/KDUMP (kexec-tools) may also pass an identifier such as "kexec" on
some architectures.
We cannot change BootLoader's behavior, because this behavior exists for
many years, and there are already user space programs search BOOT_IMAGE=
in /proc/cmdline to obtain the kernel image locations:
https://github.com/linuxdeepin/deepin-ab-recovery/blob/master/util.go
(search getBootOptions)
https://github.com/linuxdeepin/deepin-ab-recovery/blob/master/main.go
(search getKernelReleaseWithBootOption) So the the best way is handle
(ignore) it by the kernel itself, which can avoid such boot warnings (if
we use something like init=/bin/bash, bootloader identifier can even cause
a crash):
Kernel command line: BOOT_IMAGE=(hd0,1)/vmlinuz-6.x root=/dev/sda3 ro console=tty
Unknown kernel command line parameters "BOOT_IMAGE=(hd0,1)/vmlinuz-6.x", will be passed to user space.
[chenhuacai@loongson.cn: use strstarts()]
Link: https://lkml.kernel.org/r/20250815090120.1569947-1-chenhuacai@loongson.cn
Link: https://lkml.kernel.org/r/20250721101343.3283480-1-chenhuacai@loongson.cn
Signed-off-by: Huacai Chen <chenhuacai@loongson.cn>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: Christian Brauner <brauner@kernel.org>
Cc: Jan Kara <jack@suse.cz>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit feb500c7ae upstream.
To convert level-triggered alarms into edge-triggered IIO events, alarms
are masked when they are triggered. To ensure we catch subsequent
alarms, we then periodically poll to see if the alarm is still active.
If it isn't, we unmask it. Active but masked alarms are stored in
current_masked_alarm.
If an active alarm is disabled, it will remain set in
current_masked_alarm until ams_unmask_worker clears it. If the alarm is
re-enabled before ams_unmask_worker runs, then it will never be cleared
from current_masked_alarm. This will prevent the alarm event from being
pushed even if the alarm is still active.
Fix this by recalculating current_masked_alarm immediately when enabling
or disabling alarms.
Fixes: d5c70627a7 ("iio: adc: Add Xilinx AMS driver")
Signed-off-by: Sean Anderson <sean.anderson@linux.dev>
Reviewed-by: O'Griofa, Conall <conall.ogriofa@amd.com>
Tested-by: Erim, Salih <Salih.Erim@amd.com>
Acked-by: Erim, Salih <Salih.Erim@amd.com>
Link: https://patch.msgid.link/20250715002847.2035228-1-sean.anderson@linux.dev
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1315cc2dbd upstream.
AMS_ALARM_THR_DIRECT_MASK should be bit 0, not bit 1. This would cause
hysteresis to be enabled with a lower threshold of -28C. The temperature
alarm would never deassert even if the temperature dropped below the
upper threshold.
Fixes: d5c70627a7 ("iio: adc: Add Xilinx AMS driver")
Signed-off-by: Sean Anderson <sean.anderson@linux.dev>
Reviewed-by: O'Griofa, Conall <conall.ogriofa@amd.com>
Tested-by: Erim, Salih <Salih.Erim@amd.com>
Acked-by: Erim, Salih <Salih.Erim@amd.com>
Link: https://patch.msgid.link/20250715003058.2035656-1-sean.anderson@linux.dev
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 33d7ecbf69 upstream.
The ADF4350/1 features a programmable dual-modulus prescaler of 4/5 or 8/9.
When set to 4/5, the maximum RF frequency allowed is 3 GHz.
Therefore, when operating the ADF4351 above 3 GHz, this must be set to 8/9.
In this context not the RF output frequency is meant
- it's the VCO frequency.
Therefore move the prescaler selection after we derived the VCO frequency
from the desired RF output frequency.
This BUG may have caused PLL lock instabilities when operating the VCO at
the very high range close to 4.4 GHz.
Fixes: e31166f0fd ("iio: frequency: New driver for Analog Devices ADF4350/ADF4351 Wideband Synthesizers")
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Nuno Sá <nuno.sa@analog.com>
Reviewed-by: Andy Shevchenko <andy@kernel.org>
Link: https://patch.msgid.link/20250829-adf4350-fix-v2-1-0bf543ba797d@analog.com
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3379c90032 upstream.
Change the 'ret' variable in ad5421_update_ctrl() from unsigned int to
int, as it needs to store either negative error codes or zero returned
by ad5421_write_unlocked().
Fixes: 5691b23489 ("staging:iio:dac: Add AD5421 driver")
Signed-off-by: Qianfeng Rong <rongqianfeng@vivo.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@intel.com>
Link: https://patch.msgid.link/20250901135726.17601-3-rongqianfeng@vivo.com
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f9381ece76 upstream.
Change the 'ret' variable in ad5360_update_ctrl() from unsigned int to
int, as it needs to store either negative error codes or zero returned
by ad5360_write_unlocked().
Fixes: a3e2940c24 ("staging:iio:dac: Add AD5360 driver")
Signed-off-by: Qianfeng Rong <rongqianfeng@vivo.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@intel.com>
Link: https://patch.msgid.link/20250901135726.17601-2-rongqianfeng@vivo.com
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3c63ba1c43 upstream.
There are two problems with the chip configuration in this driver:
- First, is that writing 12 bytes (ARRAY_SIZE(regs)) would anyhow
lead to a config overflow due to HW auto increment implementation
in the chip.
- Second, the i2c_smbus_write_block_data write ends up in writing
unexpected value to the channel_dis register, this is because
the smbus size that is 0x03 in this case gets written to the
register. The PAC1931/2/3/4 data sheet does not really specify
that block write is indeed supported.
This problem is probably not visible on PAC1934 version where all
channels are used as the chip is properly configured by luck,
but in our case whenusing PAC1931 this leads to nonfunctional device.
Fixes: 0fb528c825 (iio: adc: adding support for PAC193x)
Suggested-by: Rene Straub <mailto:rene.straub@belden.com>
Signed-off-by: Aleksandar Gerasimovski <aleksandar.gerasimovski@belden.com>
Reviewed-by: Marius Cristea <marius.cristea@microchip.com>
Link: https://patch.msgid.link/20250811130904.2481790-1-aleksandar.gerasimovski@belden.com
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9395b3c412 upstream.
Commit 3a379bbcea ("i3c: Add core I3C infrastructure") set the default
adapter timeout for I2C transfers as 1000 (ms). However that parameter
is defined in jiffies not in milliseconds.
With mipi-i3c-hci driver this wasn't visible until commit c0a90eb55a
("i3c: mipi-i3c-hci: use adapter timeout value for I2C transfers").
Fix this by setting the default timeout as HZ (CONFIG_HZ) not 1000.
Fixes: 1b84691e78 ("i3c: dw: use adapter timeout value for I2C transfers")
Fixes: be27ed6728 ("i3c: master: cdns: use adapter timeout value for I2C transfers")
Fixes: c0a90eb55a ("i3c: mipi-i3c-hci: use adapter timeout value for I2C transfers")
Fixes: a747e01ada ("i3c: master: svc: use adapter timeout value for I2C transfers")
Fixes: d028219a9f ("i3c: master: Add basic driver for the Renesas I3C controller")
Fixes: 3a379bbcea ("i3c: Add core I3C infrastructure")
Cc: stable@vger.kernel.org # 6.17
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Link: https://lore.kernel.org/r/20250905100320.954536-1-jarkko.nikula@linux.intel.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit bc06114363 upstream.
mpfs_gpio_direction_output() actually sets the line to input mode.
Use the correct register settings for output mode so that this function
actually works as intended.
This was a copy-paste mistake made when converting to regmap during the
driver submission process. It went unnoticed because my test for output
mode is toggling LEDs on an Icicle kit which functions with the
incorrect code. The internal reporter has yet to test the patch, but on
their system the incorrect setting may be the reason for failures to
drive the GPIO lines on the BeagleV-fire board.
CC: stable@vger.kernel.org
Fixes: a987b78f36 ("gpio: mpfs: add polarfire soc gpio support")
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
Link: https://lore.kernel.org/r/20250925-boogieman-carrot-82989ff75d10@spud
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 26e5c67deb upstream.
I observed a hang when running generic/323 against a fuseblk server.
This test opens a file, initiates a lot of AIO writes to that file
descriptor, and closes the file descriptor before the writes complete.
Unsurprisingly, the AIO exerciser threads are mostly stuck waiting for
responses from the fuseblk server:
# cat /proc/372265/task/372313/stack
[<0>] request_wait_answer+0x1fe/0x2a0 [fuse]
[<0>] __fuse_simple_request+0xd3/0x2b0 [fuse]
[<0>] fuse_do_getattr+0xfc/0x1f0 [fuse]
[<0>] fuse_file_read_iter+0xbe/0x1c0 [fuse]
[<0>] aio_read+0x130/0x1e0
[<0>] io_submit_one+0x542/0x860
[<0>] __x64_sys_io_submit+0x98/0x1a0
[<0>] do_syscall_64+0x37/0xf0
[<0>] entry_SYSCALL_64_after_hwframe+0x4b/0x53
But the /weird/ part is that the fuseblk server threads are waiting for
responses from itself:
# cat /proc/372210/task/372232/stack
[<0>] request_wait_answer+0x1fe/0x2a0 [fuse]
[<0>] __fuse_simple_request+0xd3/0x2b0 [fuse]
[<0>] fuse_file_put+0x9a/0xd0 [fuse]
[<0>] fuse_release+0x36/0x50 [fuse]
[<0>] __fput+0xec/0x2b0
[<0>] task_work_run+0x55/0x90
[<0>] syscall_exit_to_user_mode+0xe9/0x100
[<0>] do_syscall_64+0x43/0xf0
[<0>] entry_SYSCALL_64_after_hwframe+0x4b/0x53
The fuseblk server is fuse2fs so there's nothing all that exciting in
the server itself. So why is the fuse server calling fuse_file_put?
The commit message for the fstest sheds some light on that:
"By closing the file descriptor before calling io_destroy, you pretty
much guarantee that the last put on the ioctx will be done in interrupt
context (during I/O completion).
Aha. AIO fgets a new struct file from the fd when it queues the ioctx.
The completion of the FUSE_WRITE command from userspace causes the fuse
server to call the AIO completion function. The completion puts the
struct file, queuing a delayed fput to the fuse server task. When the
fuse server task returns to userspace, it has to run the delayed fput,
which in the case of a fuseblk server, it does synchronously.
Sending the FUSE_RELEASE command sychronously from fuse server threads
is a bad idea because a client program can initiate enough simultaneous
AIOs such that all the fuse server threads end up in delayed_fput, and
now there aren't any threads left to handle the queued fuse commands.
Fix this by only using asynchronous fputs when closing files, and leave
a comment explaining why.
Cc: stable@vger.kernel.org # v2.6.38
Fixes: 5a18ec176c ("fuse: fix hang of single threaded fuseblk filesystem")
Signed-off-by: Darrick J. Wong <djwong@kernel.org>
Signed-off-by: Miklos Szeredi <mszeredi@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
