Commit graph

752,007 commits

Author SHA1 Message Date
Linus Walleij
e65857a64f ARM: dts: Augment panel setting for Versatile
This adds the actual VGA DAC bridge that is used in the
Versatile AB, and sets the mode to 640x480 VGA.

The "clcd" clock was incorrectly named, the proper name
(from bindings) is "clcdclk". So far drivers survived
by just getting the first clock, but future drivers will
use named clocks.

We add the panel connector to the
"arm,versatile-tft-panel" as well, the signals actually
fork on the board, reaching both the VGA DAC and the
display connector.

Cc: Mali DP Maintainers <malidp@foss.arm.com>
Reviewed-by: Liviu Dudau <liviu.dudau@arm.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2018-03-20 02:04:39 +01:00
Linus Walleij
7fbe5f7ff2 ARM: dts: Add Versatile IB2 device tree
The Versatile board can be equipped with a interface board
just named "IB2". This was created in the early 2000s for
prototyping GSM candybar phone form factor products.

The IB2 board contains:
- Cascaded interrupt controller
- Enfora Enabler GSM0308 quad-band module with antenna and
  separate audio jack
- Keypad with joystick
- Sanyo 2.5" color display
- A 28-pin connector for mounting a camera

This adds a DTS file for the combination of the Versatile AB
with an IB2 daughterboard mounted, making the LED blink and
making the system controller available for drivers, such as
the panel driver.

The device tree bindings already exist in
Documentation/devicetree/bindings/arm/arm-boards.

Cc: Mali DP Maintainers <malidp@foss.arm.com>
Reviewed-by: Liviu Dudau <liviu.dudau@arm.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2018-03-20 02:04:03 +01:00
Linus Walleij
6011a15d22 ARM: dts: Augment VGA connector bridge on Realview PBX
The PL111 in the ARM reference platforms are connected to
"panels" that are actually dumb VGA DAC connector bridges.
Now that we can support the proper bridges in the DRM driver,
fix this up.

Cc: Mali DP Maintainers <malidp@foss.arm.com>
Reviewed-by: Liviu Dudau <liviu.dudau@arm.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2018-03-20 02:03:17 +01:00
Kuninori Morimoto
83eca9f5ed
ASoC: twl6040: remove duplicated remove callback
We don't need 2 .remove callback

Fixes: 7480389fb0 ("ASoC: twl6040: replace codec to component")
Reported-by: Julia Lawall <julia.lawall@lip6.fr>
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Acked-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
2018-03-20 09:03:05 +08:00
Linus Walleij
dfdc2488c3 ARM: dts: Augment VGA connector bridge on Realview EB
The PL111 in the ARM reference platforms are connected to
"panels" that are actually dumb VGA DAC connector bridges.
Now that we can support the proper bridges in the DRM driver,
fix this up.

Cc: Mali DP Maintainers <malidp@foss.arm.com>
Reviewed-by: Liviu Dudau <liviu.dudau@arm.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2018-03-20 02:02:41 +01:00
Bard Liao
40d2677bda
ASoC: rt298: don't turn off HV and VREF if headset is detected
"HV" and "VREF" will be powered up when jack type detection process is
started and will be powered off when jack type detection process is finished.
It will generate an unexpected interrupt signal when they are powered
up during the capture process. Codec driver will do the jack type detection
process and we can't capture properly before the jack detection process is
finished. This patch will not power off the "HV" and "VREF" widgets if
headset is detected and it will solve the unexpected interrupt issue. As a
result, it will also solve the silence data captured at the beginning in
headset mic recording issue.

Signed-off-by: Bard Liao <bardliao@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
2018-03-20 09:02:21 +08:00
Stefan Agner
768d59f5d0
spi: rspi: use correct enum for DMA transfer direction
Use enum dma_transfer_direction as required by dmaengine_prep_slave_sg
instead of enum dma_data_direction. This won't change behavior in
practice as the enum values are equivalent.

This fixes two warnings when building with clang:
  drivers/spi/spi-rspi.c:538:26: warning: implicit conversion from enumeration
      type 'enum dma_data_direction' to different enumeration type
      'enum dma_transfer_direction' [-Wenum-conversion]
                                        rx->sgl, rx->nents, DMA_FROM_DEVICE,
                                                            ^~~~~~~~~~~~~~~
  drivers/spi/spi-rspi.c:558:26: warning: implicit conversion from enumeration
      type 'enum dma_data_direction' to different enumeration type
      'enum dma_transfer_direction' [-Wenum-conversion]
                                        tx->sgl, tx->nents, DMA_TO_DEVICE,
                                                            ^~~~~~~~~~~~~

Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Mark Brown <broonie@kernel.org>
2018-03-20 09:02:12 +08:00
Bard Liao
8153362e75
ASoC: rt286: don't turn off HV and VREF if headset is detected
"HV" and "VREF" will be powered up when jack type detection process is
started and will be powered off when jack type detection process is finished.
It will generate an unexpected interrupt signal when they are powered
up during the capture process. Codec driver will do the jack type detection
process and we can't capture properly before the jack detection process is
finished. This patch will not power off the "HV" and "VREF" widgets if
headset is detected and it will solve the unexpected interrupt issue. As a
result, it will also solve the silence data captured at the beginning in
headset mic recording issue.

Signed-off-by: Bard Liao <bardliao@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
2018-03-20 09:02:06 +08:00
Linus Walleij
3088a5c7ad ARM: dts: Augment VGA connector bridge on PB1176
The PL111 in the ARM reference platforms are connected to
"panels" that are actually dumb VGA DAC connector bridges.
Now that we can support the proper bridges in the DRM driver,
fix this up.

Cc: Mali DP Maintainers <malidp@foss.arm.com>
Reviewed-by: Liviu Dudau <liviu.dudau@arm.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2018-03-20 02:01:57 +01:00
Linus Walleij
82089116a5 ARM: dts: Augment VGA connector bridge on PB11MPcore
The PL111 in the ARM reference platforms are connected to
"panels" that are actually dumb VGA DAC connector bridges.
Now that we can support the proper bridges in the DRM driver,
fix this up.

Cc: Mali DP Maintainers <malidp@foss.arm.com>
Reviewed-by: Liviu Dudau <liviu.dudau@arm.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2018-03-20 02:01:15 +01:00
James Kelly
a01df75ce7
ASoC: ssm2602: Replace reg_default_raw with reg_default
SSM2602 driver is broken on recent kernels (at least
since 4.9). User space applications such as amixer or
alsamixer get EIO when attempting to access codec
controls via the relevant IOCTLs.

Root cause of these failures is the regcache_hw_init
function in drivers/base/regmap/regcache.c, which
prevents regmap cache initalization from the
reg_defaults_raw element of the regmap_config structure
when registers are write only. It also disables the
regmap cache entirely when all registers are write only
or volatile as is the case for the SSM2602 driver.

Using the reg_defaults element of the regmap_config
structure rather than the reg_defaults_raw element to
initalize the regmap cache avoids the logic in the
regcache_hw_init function entirely. It also makes this
driver consistent with other ASoC codec drivers, as
this driver was the ONLY codec driver that used the
reg_defaults_raw element to initalize the cache.

Tested on Digilent Zybo Z7 development board which has
a SSM2603 codec chip connected to a Xilinx Zynq SoC.

Signed-off-by: James Kelly <jamespeterkelly@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
2018-03-20 09:01:09 +08:00
Al Viro
3e3511b3c8 sparc: get rid of sys_sparc_pipe() wrappers
just use current_pt_regs()

Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
2018-03-19 20:48:50 -04:00
Jerome Brunet
c339f0e29c ARM64: dts: meson-gx: make efuse read-only
efuse is one time programmable, so it is safer to deny write request
to this memory, unless the user is savvy enough to remove the read-only
flag from DTB

Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
2018-03-19 16:44:39 -07:00
Neil Armstrong
f842c41adc amlogic: meson-gx-socinfo: Update soc ids
Updates the Amlogic Meson SoCs IDs for the Armv8 based SoCs.
It includes the new families and packages.

Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
2018-03-19 16:40:26 -07:00
Neil Armstrong
97ac009309 ARM64: dts: meson: bump mali450 clk to 744MHz
The Mali-450 IP can run up to 744MHz, bump the frequency using
the GP0 PLL clock.

Cc: Michal Lazo <michal.lazo@gmail.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
2018-03-19 16:39:26 -07:00
Dhinakaran Pandiyan
b1e314462b drm/i915/dp: Write to SET_POWER dpcd to enable MST hub.
If bios sets up an MST output and hardware state readout code sees this is
an SST configuration, when disabling the encoder we end up calling
->post_disable_dp() hook instead of the MST version. Consequently, we write
to the DP_SET_POWER dpcd to set it D3 state. Further along when we try
enable the encoder in MST mode, POWER_UP_PHY transaction fails to power up
the MST hub. This results in continuous link training failures which keep
the system busy delaying boot. We could identify bios MST boot discrepancy
and handle it accordingly but a simple way to solve this is to write to the
DP_SET_POWER dpcd for MST too.

Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=105470
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reported-by: Laura Abbott <labbott@redhat.com>
Cc: stable@vger.kernel.org
Fixes: 5ea2355a10 ("drm/i915/mst: Use MST sideband message transactions for dpms control")
Tested-by: Laura Abbott <labbott@redhat.com>
Signed-off-by: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180314054825.1718-1-dhinakaran.pandiyan@intel.com
(cherry picked from commit ad260ab32a)
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
2018-03-19 16:21:52 -07:00
Alexandre Belloni
f6b1a3a4a7 parisc: time: stop validating rtc_time in .read_time
The RTC core is always calling rtc_valid_tm after the read_time callback.
It is not necessary to call it just before returning from the callback.

Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Acked-by: Helge Deller <deller@gmx.de>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
2018-03-20 00:02:09 +01:00
Linus Torvalds
1b5f3ba415 Merge branch 'for-4.16-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/cgroup
Pull cgroup fixes from Tejun Heo:
 "Two commits to fix the following subtle cgroup2 behavior bugs:

   - cpu.max was rejecting config when it shouldn't

   - thread mode enable was allowed when it shouldn't"

* 'for-4.16-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/cgroup:
  cgroup: fix rule checking for threaded mode switching
  sched, cgroup: Don't reject lower cpu.max on ancestors
2018-03-19 15:39:02 -07:00
Takashi Iwai
b1abf6fc49 ACPI / watchdog: Fix off-by-one error at resource assignment
The resource allocation in WDAT watchdog has off-one-by error, it sets
one byte more than the actual end address.  This may eventually lead
to unexpected resource conflicts.

Fixes: 058dfc7670 (ACPI / watchdog: Add support for WDAT hardware watchdog)
Cc: 4.9+ <stable@vger.kernel.org> # 4.9+
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Acked-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
2018-03-19 23:17:07 +01:00
Linus Torvalds
c6256ca9c0 Merge branch 'for-4.16-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/wq
Pull workqueue fixes from Tejun Heo:
 "Two low-impact workqueue commits.

  One fixes workqueue creation error path and the other removes the
  unused cancel_work()"

* 'for-4.16-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/wq:
  workqueue: remove unused cancel_work()
  workqueue: use put_device() instead of kfree()
2018-03-19 15:13:04 -07:00
Linus Torvalds
0d707a2f24 Merge branch 'for-4.16-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/percpu
Pull percpu fixes from Tejun Heo:
 "Late percpu pull request for v4.16-rc6.

   - percpu allocator pool replenishing no longer triggers OOM or
     warning messages.

     Also, the alloc interface now understands __GFP_NORETRY and
     __GFP_NOWARN. This is to allow avoiding OOMs from userland
     triggered actions like bpf map creation.

     Also added cond_resched() in alloc loop.

   - perpcu allocation now can be interrupted by kill sigs to avoid
     deadlocking OOM killer.

   - Added Dennis Zhou as a co-maintainer.

     He has rewritten the area map allocator, understands most of the
     code base and has been responsive for all bug reports"

* 'for-4.16-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/percpu:
  percpu_ref: Update doc to dissuade users from depending on internal RCU grace periods
  mm: Allow to kill tasks doing pcpu_alloc() and waiting for pcpu_balance_workfn()
  percpu: include linux/sched.h for cond_resched()
  percpu: add a schedule point in pcpu_balance_workfn()
  percpu: allow select gfp to be passed to underlying allocators
  percpu: add __GFP_NORETRY semantics to the percpu balancing path
  percpu: match chunk allocator declarations with definitions
  percpu: add Dennis Zhou as a percpu co-maintainer
2018-03-19 14:48:35 -07:00
Srinivas Kandagatla
8bcde6582c clk: qcom: rpmcc: Add support to XO buffered clocks
XO is onchip buffer clock to generate 19.2MHz.

This patch adds support to 5 XO buffer clocks found on PMIC8921,
these buffer clocks can be controlled from external pin or in
manual mode.

Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
2018-03-19 14:40:26 -07:00
Weiyi Lu
f72595cf44 clk: mediatek: update clock driver of MT2712
According to ECO design change,
1. add new clock mux data and change some
2. add new clock gate data and clock factor data
3. change status register offset of infra subsystem

Signed-off-by: Weiyi Lu <weiyi.lu@mediatek.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
2018-03-19 14:37:40 -07:00
Weiyi Lu
8465baaeca dt-bindings: clock: add clocks for MT2712
add new clocks according to ECO design change

Signed-off-by: Weiyi Lu <weiyi.lu@mediatek.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
2018-03-19 14:37:31 -07:00
Jeffy Chen
cef7b18c3e clk: lpc32xx: Set name of regmap_config
We are now allowing to register debugfs without a valid device, and not
having a valid name will end up using "dummy*" to create debugfs dir.

Signed-off-by: Jeffy Chen <jeffy.chen@rock-chips.com>
Acked-by: Vladimir Zapolskiy <vz@mleia.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
2018-03-19 14:35:16 -07:00
Linus Torvalds
efac2483e8 Merge branch 'for-4.16-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/libata
Pull libata fixes from Tejun Heo:
 "I sat on them too long and it's quite a few this late, but nothing has
  a wide blast area. The changes are...

   - Fix corner cases in SG command handling.

   - Recent introduction of default powersaving mode config option
     exposed several devices with broken powersaving behaviors. A number
     of patches to update the blacklist accordingly.

   - Fix a kernel panic on SAS hotplug.

   - Other misc and device specific updates"

* 'for-4.16-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/libata:
  libata: Modify quirks for MX100 to limit NCQ_TRIM quirk to MU01 version
  libata: Make Crucial BX100 500GB LPM quirk apply to all firmware versions
  libata: Apply NOLPM quirk to Crucial M500 480 and 960GB SSDs
  libata: Enable queued TRIM for Samsung SSD 860
  PCI: Add function 1 DMA alias quirk for Highpoint RocketRAID 644L
  ahci: Add PCI-id for the Highpoint Rocketraid 644L card
  ata: do not schedule hot plug if it is a sas host
  libata: disable LPM for Crucial BX100 SSD 500GB drive
  libata: Apply NOLPM quirk to Crucial MX100 512GB SSDs
  libata: update documentation for sysfs interfaces
  ata: sata_rcar: Remove unused variable in sata_rcar_init_controller()
  libata: transport: cleanup documentation of sysfs interface
  sata_rcar: Reset SATA PHY when Salvator-X board resumes
  libata: don't try to pass through NCQ commands to non-NCQ devices
  libata: remove WARN() for DMA or PIO command without data
  libata: fix length validation of ATAPI-relayed SCSI commands
  ata: libahci: fix comment indentation
  ahci: Add check for device presence (PCIe hot unplug) in ahci_stop_engine()
  libata: Fix compile warning with ATA_DEBUG enabled
2018-03-19 14:23:30 -07:00
Chen-Yu Tsai
dbb6d86415
ARM: dts: sun9i: cubieboard4: Enable VGA display output
The Cubieboard4 has a dumb VGA DAC connected to the output of LCD0,
providing VGA output through the onboard VGA connector. The DDC lines
are connected to i2c3.

The VGA DAC is a GM7123, which is compatible with Analog Devices'
ADV7123, except it only takes 3.3V power, and has a lower standby power
consumption. The datasheet found online lists "Chengdu GoldTel Electronical
Technology Co., Ltd." as its designer. The company changed its name in
2014 to "Chengdu Corpro Technology Co., Ltd.". Their website lists similar
ICs, but not actually the GM7123.

Enable the display pipeline with the VGA DAC and connector, and i2c3
for DDC.

Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
2018-03-19 22:13:05 +01:00
Chen-Yu Tsai
0210470482
ARM: dts: sun9i: Add pinmux settings for LCD0 RGB888 output.
The A80 supports RGB888 with H/V sync from LCD0. Add a pinmux setting
for the needed pins.

Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
2018-03-19 22:13:01 +01:00
Chen-Yu Tsai
f1317774c6
ARM: dts: sun9i: Add device nodes for documented display pipelines for A80
The Allwinner A80 SoC has 3 display pipelines, of which some parts are
documented:

  - 3x display front ends (FE), documented
  - 2x display enhancement units (DEU), undocumented
  - 3x display back ends (BE), documented
  - 2x dynamic range controller (DRC), undocumented
  - 2x LCDC/TCONs, documented
  - 1x LCDC/TCON, undocumented, and probably not useable
  - 1x HDMI transmitter, undocumented but DesignWare compatible
  - 1x MERGE block, function unknown

This patch adds device nodes for the first 2 documented pipelines:

    FE0 - DEU0 - - BE0 - DRC0 - TCON0
		x
    FE1 - DEU1 - - BE1 - DRC1 - TCON1

Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
2018-03-19 22:12:58 +01:00
Harald Geyer
c916eb95bc
arm64: dts: allwinner: a64: Add support for TERES-I laptop
The TERES-I is an open hardware laptop built by Olimex using the
Allwinner A64 SoC.

Add the board specific .dts file, which includes the A64 .dtsi and
enables the peripherals that we support so far.

Signed-off-by: Harald Geyer <harald@ccbib.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
2018-03-19 22:12:31 +01:00
Harald Geyer
c1cff65f9b
arm64: dts: allwinner: a64: add simplefb for A64 SoC
The A64 SoC features two display pipelines, one has a LCD output, the
other has a HDMI output.

Add support for simplefb for the LCD output. Tested on Teres I.

This patch was inspired by work of Icenowy Zheng.

Signed-off-by: Harald Geyer <harald@ccbib.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
2018-03-19 22:12:28 +01:00
Harald Geyer
d41850437c
arm64: dts: allwinner: a64: Add watchdog
Add a watchdog node for the A64, automatically enabled on all boards.
Since the device is compatible with an existing driver, we only reserve
a new compatible string to be used together with the fall back.
Tested on Olimex Teres-I.

Signed-off-by: Harald Geyer <harald@ccbib.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
2018-03-19 22:12:26 +01:00
Harald Geyer
11239fe6a0
arm64: dts: allwinner: a64: Add i2c0 pins
Add the proper pin group node to reference in board files.

Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Harald Geyer <harald@ccbib.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
2018-03-19 22:12:25 +01:00
Icenowy Zheng
494d836762
arm64: allwinner: h6: add support for Pine H64 board
Pine H64 is an Allwinner H6-based SBC from Pine64, with the following
features:

- 1GiB/2GiB/4GiB LPDDR3 DRAM (in 4GiB situation only 3GiB is
accessible)
- AXP805 PMIC
- Raspberry-Pi-compatible GPIO header, "Euler" GPIO header (not
compatible with the "Euler" on Pine A64) and "Expansion" pin header
- 2 USB 2.0 ports and 1 USB 3.0 ports
- Audio jack
- MicroSD slot and eMMC module slot
- on-board SPI NOR flash
- 1Gbps Ethernet port (via RTL8211E PHY)
- HDMI port

Adds initial support for it, including the UART on the Expansion pin
header.

Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Tested-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
2018-03-19 22:12:23 +01:00
Icenowy Zheng
e54be32d02
arm64: allwinner: h6: add the basical Allwinner H6 DTSI file
Allwinner H6 is a new SoC with Cortex-A53 cores from Allwinner, with its
memory map fully reworked and some high-speed peripherals (PCIe, USB
3.0) introduced.

This commit adds the basical DTSI file of it, including the clock
support and UART support.

Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
2018-03-19 22:12:21 +01:00
Maxime Ripard
ddc389f5a4
drm/sun4i: backend: Support YUV planes
Now that we have the guarantee that we will have only a single YUV plane,
actually support them. The way it works is not really straightforward,
since we first need to enable the YUV mode in the plane that we want to
setup, and then we have a few registers to setup the YUV buffer and
parameters.

We also need to setup the color correction to actually have something
displayed.

Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Link: https://patchwork.freedesktop.org/patch/msgid/66088c1398bd3189123f28a89a7ccc669fe9f296.1519931807.git-series.maxime.ripard@bootlin.com
2018-03-19 22:04:57 +01:00
Shawn Lin
1f9c63e8de clk: Don't show the incorrect clock phase
It's found that the clock phase output from clk_summary is
wrong compared to the actual phase reading from the register.

cat /sys/kernel/debug/clk/clk_summary | grep sdio_sample
sdio_sample     0        1        0 50000000          0 -22

It exposes an issue that clk core, clk_core_get_phase, always
returns the cached core->phase which should be either updated
by calling clk_set_phase or directly from the first place the
clk was registered.

When registering the clk, the core->phase geting from ->get_phase()
may return negative value indicating error. This is quite common
since the clk's phase may be highly related to its parent chain,
but it was temporarily orphan when registered, since its parent
chains hadn't be ready at that time, so the clk drivers decide to
return error in this case. However, if no clk_set_phase is called or
maybe the ->set_phase() isn't even implemented, the core->phase would
never be updated. This is wrong, and we should try to update it when
all its parent chains are settled down, like the way of updating clock
rate for that. But it's not deserved to complicate the code now and
just update it anyway when calling clk_core_get_phase, which would be
much simple and enough.

Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Acked-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
2018-03-19 14:02:49 -07:00
Richard Genoud
6a4a459580 clk: mvebu: armada-38x: add support for missing clocks
Clearfog boards can come with a CPU clocked at 1600MHz (commercial)
or 1333MHz (industrial).

They have also some dip-switches to select a different clock (666, 800,
1066, 1200).

The funny thing is that the recovery button is on the MPP34 fq selector.
So, when booting an industrial board with this button down, the frequency
666MHz is selected (and the kernel didn't boot).

This patch add all the missing clocks.

The only mode I didn't test is 2GHz (uboot found 4294MHz instead :/ ).

Fixes: 0e85aeced4 ("clk: mvebu: add clock support for Armada 380/385")
Cc: <stable@vger.kernel.org> # 3.16.x: 9593f4f56c: clk: mvebu: armada-38x: add support for 1866MHz variants
Cc: <stable@vger.kernel.org> # 3.16.x

Signed-off-by: Richard Genoud <richard.genoud@gmail.com>
Acked-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
2018-03-19 13:53:57 -07:00
Mike Looijmans
2e838e7f3a clk: clk-gpio: Allow GPIO to sleep in set/get_parent
When changing or retrieving clock parents, the caller is in a sleepable
state (like prepare) so the GPIO operation need not be atomic. Replace
gpiod_{g|s}et_value with gpiod_{g|s}et_value_cansleep in the {g|s}et_parent
calls for the GPIO based clock mux.

This fixes a "slowpath" warning when the GPIO controller is an I2C expander
or something similar.

Signed-off-by: Mike Looijmans <mike.looijmans@topic.nl>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
2018-03-19 13:53:08 -07:00
Riku Voipio
3a49afb84c clk: enable hi655x common clk automatically
Without COMMON_CLK_HI655X Wifi and bluetooth are non-functional on Hikey.
As suggested by Arnd, enable the driver automatically when the parent
driver is selected. With sensible defaults in place, we can leave other
choices for EXPERT.

Cc: John Stultz <john.stultz@linaro.org>
Cc: Wei Xu <xuwei5@hisilicon.com>
Cc: Daniel Lezcano <daniel.lezcano@linaro.org>
Suggested-by: Arnd Bergmann <arnd@linaro.org>
Signed-off-by: Riku Voipio <riku.voipio@linaro.org>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
2018-03-19 13:52:20 -07:00
Benjamin Gaignard
da32d3539f clk: stm32: add configuration flags for each of the stm32 drivers
Add two configuration flags to be able to not compile all the time
stm32f and stm32h7 drivers when ARCH_STM32 is set.
That help to save some space on those small platforms.

Signed-off-by: Benjamin Gaignard <benjamin.gaignard@st.com>
Acked-by: Gabriel Fernandez <gabriel.fernandez@st.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
2018-03-19 13:49:36 -07:00
Patrice Chotard
f9acf1057d clk: stm32: Add clk entry for SDMMC2 on stm32F769
STM32F769 has 2 SDMMC port, add clock entry for the second one.

Signed-off-by: Alexandre TORGUE <alexandre.torgue@st.com>
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
2018-03-19 13:46:07 -07:00
Matan Barak
185899ee8d IB/uverbs: Enable ioctl() uAPI by default for new verbs
Enable the ioctl() uAPI for IB by default if the standard write()
uAPI (INFINIBAND_USER_ACCESS) is enabled. Verbs that are
also available under the old write() uAPI are put inside a new
INFINIBAND_EXP_LEGACY_VERBS_NEW_UAPI Kconfig.

Reviewed-by: Yishai Hadas <yishaih@mellanox.com>
Signed-off-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
2018-03-19 14:45:17 -06:00
Matan Barak
3d64addd43 IB/uverbs: Add macros to simplify adding driver specific attributes
Previously, adding driver specific attributes required drivers to
declare all the hierarchy - object tree, object, methods and the
attributes themselves. A common use case is adding a few attributes to
an existing common method.
In order to simplify the driver's code, we add some macros to do all
these declarations automatically.

Signed-off-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
2018-03-19 14:45:17 -06:00
Matan Barak
41b2a71fc8 IB/uverbs: Move ioctl path of create_cq and destroy_cq to a new file
Currently, all objects are declared in uverbs_std_types. This could lead
to a huge file once we implement all objects, methods and handlers.
Moving each object to its own file to keep the files smaller and more
readable. uverbs_std_types.c will only contain the parsing tree
definition and objects without any methods.

Signed-off-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
2018-03-19 14:45:17 -06:00
Matan Barak
dfb1395573 IB/uverbs: Expose parsing tree of all common objects to providers
The ioctl() based uverbs is based on merging feature trees. This teaches
the generic parser how to parse methods according to the provider's
support. In order to support merging with the common objects, exporting
the common-object-tree to the provider drivers.

Reviewed-by: Yishai Hadas <yishaih@mellanox.com>
Signed-off-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
2018-03-19 14:45:17 -06:00
Matan Barak
c66db31113 IB/uverbs: Safely extend existing attributes
Previously, we've used UVERBS_ATTR_SPEC_F_MIN_SZ for extending existing
attributes. The behavior of this flag was the kernel accepts anything
bigger than the minimum size it specified. This is unsafe, since in
order to safely extend an attribute, we need to make sure unknown size
is zeroed. Replacing UVERBS_ATTR_SPEC_F_MIN_SZ with
UVERBS_ATTR_SPEC_F_MIN_SZ_OR_ZERO, which essentially checks that the
unknown size is zero. In addition, attributes are now decorated with
UVERBS_ATTR_TYPE and UVERBS_ATTR_STRUCT, so we can provide the minimum
and known length.

Users of this flag needs to use copy_from_or_zero functions/macros.

Reviewed-by: Yishai Hadas <yishaih@mellanox.com>
Signed-off-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
2018-03-19 14:45:17 -06:00
Matan Barak
1f07e08fab IB/uverbs: Enable compact representation of uverbs_attr_spec
Downstream patches extend uverbs_attr_spec with new fields.
In order to save space, we move the type and flags fields to
the various attribute flavors contained in the union.

Reviewed-by: Yishai Hadas <yishaih@mellanox.com>
Signed-off-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
2018-03-19 14:45:17 -06:00
Matan Barak
0ede73bc01 IB/uverbs: Extend uverbs_ioctl header with driver_id
Extending uverbs_ioctl header with driver_id and another reserved
field. driver_id should be used in order to identify the driver.
Since every driver could have its own parsing tree, this is necessary
for strace support.
Downstream patches take off the EXPERIMENTAL flag from the ioctl() IB
support and thus we add some reserved fields for future usage.

Reviewed-by: Yishai Hadas <yishaih@mellanox.com>
Signed-off-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
2018-03-19 14:45:17 -06:00
Matan Barak
1f7ff9d5d3 IB/uverbs: Move to new headers and make naming consistent
Use macros to make names consistent in ioctl() uAPI:
The ioctl() uAPI works with object-method hierarchy. The method part
also states which handler should be executed when this method is called
from user-space. Therefore, we need to tie method, method's id, method's
handler and the object owning this method together.
Previously, this was done through explicit developer chosen names.
This makes grepping the code harder. Changing the method's name,
method's handler and object's name to be automatically generated based
on the ids.

The headers are split in a way so they be included and used by
user-space. One header strictly contains structures that are used
directly by user-space applications, where another header is used for
internal library (i.e. libibverbs) to form the ioctl() commands.
Other header simply contains the required general command structure.

Reviewed-by: Yishai Hadas <yishaih@mellanox.com>
Signed-off-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
2018-03-19 14:45:17 -06:00