cma_port_is_unique() allows local port reuse if the quad (source
address and port, destination address and port) for this connection
is unique. However, if the destination info is zero or unspecified, it
can't make a correct decision but still allows port reuse. For example,
sometimes rdma_bind_addr() is called with unspecified destination and
reusing the port can lead to creating a connection with a duplicate quad,
after the destination is resolved. The issue manifests when MPI scale-up
tests hang after the duplicate quad is used.
Set the destination address family and add checks for zero destination
address and port to prevent source port reuse based on invalid destination.
Fixes: 19b752a19d ("IB/cma: Allow port reuse for rdma_id")
Reviewed-by: Sean Hefty <sean.hefty@intel.com>
Signed-off-by: Tatyana Nikolova <tatyana.e.nikolova@intel.com>
Signed-off-by: Shiraz Saleem <shiraz.saleem@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Split IPv6 addresses at the colon that separates the IPv6 address
and the port number instead of at a colon in the middle of the IPv6
address. Check whether the IPv6 address is surrounded with square
brackets.
Fixes: 19f313438c ("IB/srp: Add RDMA/CM support")
Signed-off-by: Bart Van Assche <bart.vanassche@wdc.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
After v4.12 commit e2460f2a4b ("dm: mark targets that pass integrity
data"), dm-multipath, e.g. on DIF+DIX SCSI disk paths, does not support
block integrity any more. So add it to the whitelist.
This is also a pre-requisite to use block integrity with other dm layer(s)
on top of multipath, such as kpartx partitions (dm-linear) or LVM.
Also, bump target version to reflect this fix.
Fixes: e2460f2a4b ("dm: mark targets that pass integrity data")
Cc: <stable@vger.kernel.org> #4.12+
Bisected-by: Fedor Loshakov <loshakov@linux.vnet.ibm.com>
Signed-off-by: Steffen Maier <maier@linux.vnet.ibm.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Just set the GTT domain as mandatory, so that the BO is validated into
it on first use. This allows us to setup the sg table later on.
Signed-off-by: Christian König <christian.koenig@amd.com>
Acked-by: Roger He <Hongbo.He@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Instead of moving this to the SYSTEM domain just drop the backing store
and let the resulting allocation be freed.
Signed-off-by: Christian König <christian.koenig@amd.com>
Acked-by: Roger He <Hongbo.He@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Better to set this with all other fields as well.
Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Roger He <Hongbo.He@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Instead of calculating the size in bytes just to recalculate the number
of pages from it pass the BO directly to the function.
Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Roger He <Hongbo.He@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Allows us to gut a BO of it's backing store when the driver says that it
isn't needed any more.
Signed-off-by: Christian König <christian.koenig@amd.com>
Acked-by: Roger He <Hongbo.He@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
this patch actually refactor mailbox implmentations, and
all below changes are needed together to fix all those mailbox
handshake issues exposured by heavey TDR test.
1)refactor all mailbox functions based on byte accessing for mb_control
reason is to avoid touching non-related bits when writing trn/rcv part of
mailbox_control, this way some incorrect INTR sent to hypervisor
side could be avoided, and it fixes couple handshake bug.
2)trans_msg function re-impled: put a invalid
logic before transmitting message to make sure the ACK bit is in
a clear status, otherwise there is chance that ACK asserted already
before transmitting message and lead to fake ACK polling.
(hypervisor side have some tricks to workaround ACK bit being corrupted
by VF FLR which hase an side effects that may make guest side ACK bit
asserted wrongly), and clear TRANS_MSG words after message transferred.
3)for mailbox_flr_work, it is also re-worked: it takes the mutex lock
first if invoked, to block gpu recover's participate too early while
hypervisor side is doing VF FLR. (hypervisor sends FLR_NOTIFY to guest
before doing VF FLR and sentds FLR_COMPLETE after VF FLR done, and
the FLR_NOTIFY will trigger interrupt to guest which lead to
mailbox_flr_work being invoked)
This can avoid the issue that mailbox trans msg being cleared by its VF FLR.
4)for mailbox_rcv_irq IRQ routine, it should only peek msg and schedule
mailbox_flr_work, instead of ACK to hypervisor itself, because FLR_NOTIFY
msg sent from hypervisor side doesn't need VF's ACK (this is because
VF's ACK would lead to hypervisor clear its trans_valid/msg, and this
would cause handshake bug if trans_valid/msg is cleared not due to
correct VF ACK but from a wrong VF ACK like this "FLR_NOTIFY" one)
This fixed handshake bug that sometimes GUEST always couldn't receive
"READY_TO_ACCESS_GPU" msg from hypervisor.
5)seperate polling time limite accordingly:
POLL ACK cost no more than 500ms
POLL MSG cost no more than 12000ms
POLL FLR finish cost no more than 500ms
6) we still need to set adev into in_gpu_reset mode after we received
FLR_NOTIFY from host side, this can prevent innocent app wrongly succesed
to open amdgpu dri device.
FLR_NOFITY is received due to an IDLE hang detected from hypervisor side
which indicating GPU is already die in this VF.
v2:
use MACRO as the offset of mailbox_control register
don't test if NOTIFY_CMPL event in rcv_msg since it won't
recieve that message anymore
Signed-off-by: Monk Liu <Monk.Liu@amd.com>
Reviewed-by: Pixel Ding <Pixel.Ding@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
mailbox registers can be accessed with a byte boundry according
to BIF team, so this patch prepares register byte access
and will be used by following patches.
Actually, for mailbox registers once the byte field is touched even not changed,
the mailbox behaves, so we need the byte width accessing to those sort of regs.
Signed-off-by: Monk Liu <Monk.Liu@amd.com>
Reviewed-by: Pixel Ding <Pixel.Ding@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
The vram type for dGPU is stored in umc_info while sys mem type
for APU is stored in integratedsysteminfo
Signed-off-by: Hawking Zhang <Hawking.Zhang@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
The commit d296278fd372003fc69588acfd0c0c5edbdf4874 added support for
detecting DDR4 but omitted the label that is printed out in
amdgpu_bo_init() resulting in a KASAN error.
Signed-off-by: Tom St Denis <tom.stdenis@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
The amdgpu_ucode_fini_bo should be called after gfx_v8_0_hw_fini,
or it will have KCQ disable failed issue.
For Tonga, as it firstly finishes SMC block, and the SMC hw fini
will call amdgpu_ucode_fini, which will lead the amdgpu_ucode_fini_bo
called before gfx_v8_0_hw_fini, this is incorrect.
Signed-off-by: Emily Deng <Emily.Deng@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
The amdgpu_pm_sysfs_fini should call before amdgpu_device_ip_fini,
or the adev->pm.dpm_enabled would be set to 0, then the device files
related to pp won't be removed by amdgpu_pm_sysfs_fini when unload
driver.
Signed-off-by: Emily Deng <Emily.Deng@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
We don't need the page array for prime shared BOs, stop allocating it.
Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Roger He <Hongbo.He@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This allows drivers to only allocate dma addresses, but not a page
array.
Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Roger He <Hongbo.He@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Let's stop mangling everything in a single header and create one header
per object instead.
Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Roger He <Hongbo.He@amd.com>
Acked-by: Michel Dänzer <michel.daenzer@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
When we re-enable ATR we need to restore the input set for TCPv4
filters, in order for ATR to function correctly. We already do this for
the normal case of re-enabling ATR when disabling ntuple support.
However, when re-enabling ATR after the last TCPv4 filter is removed (but
when ntuple support is still active), we did not restore the TCPv4
filter input set.
This can cause problems if the TCPv4 filters from FDir had changed the
input set, as ATR will no longer behave as expected.
When clearing the ATR auto-disable flag, make sure we restore the TCPv4
input set to avoid this.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
All callers to ib_modify_qp_is_ok() provides enum ib_qp_state
makes the checks of out-of-scope redundant. Let's remove them
together with updating function signature to return boolean result.
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Reviewed-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
QP states provided by core layer are converted to enum ib_qp_state
and better to use internal variable in that type instead of int.
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
The QP state is internal enum which is checked at the driver
level by calling to ib_modify_qp_is_ok(). Move this check closer
to user and leave kernel users to be checked by compiler.
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Reviewed-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
This patch overwrites number of ports for X722 devices with support
for OCP PHY mezzanine.
The old method with checking if port is disabled in the PRTGEN_CNF
register cannot be used in this case. When the OCP is removed, ports
were seen as disabled, which resulted in wrong calculation of partition
id, that caused WoL to be disabled on certain ports.
Signed-off-by: Mariusz Stachura <mariusz.stachura@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
A future patch needs to expand on the logic for re-enabling ATR. Doing
so would cause some code to break the 80-character line limit.
To reduce the level of indentation, factor out helper functions for
re-enabling ATR and SB rules.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When hardware has trouble with a particular filter, we delete it from
the list. Unfortunately, we did not properly update the per-filter
statistic when doing so.
Create a helper function to handle this, and properly reduce the
necessary counter so that it tracks the number of active filters
properly.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When VF requests adding of MAC filters the checking is done against number
of already present MAC filters not adding them at the same time. It makes
it possible to add a bunch of filters at once possibly exceeding
acceptable limit of I40E_VC_MAX_MAC_ADDR_PER_VF filters.
This happens because when checking vf->num_mac, we do not check how many
filters are being requested at once. Modify the check function to ensure
that it knows how many filters are being requested. This allows the
check to ensure that the total number of filters in a single request
does not cause us to go over the limit.
Additionally, move the check to within the lock to ensure that the
vf->num_mac is checked while holding the lock to maintain consistency.
We could have simply moved the call to i40e_vf_check_permission to
within the loop, but this could cause a request to be non-atomic, and
add some but not all the addresses, while reporting an error code. We
want to avoid this behavior so that users are not confused about which
filters have or have not been added.
Signed-off-by: Filip Sadowski <filip.sadowski@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Gratian Crisan reported that vmalloc_fault() crashes when CONFIG_HUGETLBFS
is not set since the function inadvertently uses pXn_huge(), which always
return 0 in this case. ioremap() does not depend on CONFIG_HUGETLBFS.
Fix vmalloc_fault() to call pXd_large() instead.
Fixes: f4eafd8bcd ("x86/mm: Fix vmalloc_fault() to handle large pages properly")
Reported-by: Gratian Crisan <gratian.crisan@ni.com>
Signed-off-by: Toshi Kani <toshi.kani@hpe.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: stable@vger.kernel.org
Cc: linux-mm@kvack.org
Cc: Borislav Petkov <bp@alien8.de>
Cc: Andy Lutomirski <luto@kernel.org>
Link: https://lkml.kernel.org/r/20180313170347.3829-2-toshi.kani@hpe.com
We used to use the function i40e_vlan_rx_register as a way to hook
into the now defunct .ndo_vlan_rx_register netdev hook. This was
removed but we kept the function around because we still used it
internally to control enabling or disabling of VLAN stripping.
As pointed out in upstream review, VLAN stripping is only used in a
single location and the previous function is quite small, just inline
it into i40e_restore_vlan() rather than carrying the function
separately.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Fix for "Resource temporarily unavailable" problem when virsh is
trying to attach a device to VM. When the VF driver is loaded on
host and virsh is trying to attach it to the VM and set a MAC
address, it ends with a race condition between i40e_reset_vf and
i40e_ndo_set_vf_mac functions. The bug is fixed by adding polling
in i40e_ndo_set_vf_mac function For when the VF is in Reset mode.
Signed-off-by: Paweł Jabłoński <pawel.jablonski@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
It seems this is a copy-paste error and that the proper variable to use
in this particular case is _src_ instead of _dst_.
Addresses-Coverity-ID: 1465282 ("Copy-paste error")
Fixes: 0075fa0fad ("i40evf: Add support to apply cloud filters")
Signed-off-by: Gustavo A R Silva <garsilva@embeddedor.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
i40e_fcoe support was removed via commit 9eed69a914 ("i40e: Drop FCoE code from core driver files")
But this left files in place but un-compilable.
Let's finish the cleaning.
Signed-off-by: Corentin Labbe <clabbe@baylibre.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
For testing the exitless interrupt support it turned out useful to
have separate counters for inject and delivery of I/O interrupt.
While at it do the same for all interrupt types. For timer
related interrupts (clock comparator and cpu timer) we even had
no delivery counters. Fix this as well. On this way some counters
are being renamed to have a similar name.
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
This counter can be used for administration, debug or test purposes.
Suggested-by: Vladislav Mironov <mironov@de.ibm.com>
Signed-off-by: QingFeng Hao <haoqf@linux.vnet.ibm.com>
Reviewed-by: Christian Borntraeger <borntraeger@de.ibm.com>
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
Reviewed-by: David Hildenbrand <david@redhat.com>
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
The S390 architecture does not support any graphics hardware,
but with the latest support for Virtio GPU in Linux and Virtio
GPU emulation in QEMU, it's possible to enable graphics for
S390 using the Virtio GPU device.
To enable display we need to enable the Linux Virtual Terminal (VT)
layer for S390. But the VT subsystem initializes quite early
at boot so we need a dummy console driver till the Virtio GPU
driver is initialized and we can run the framebuffer console.
The framebuffer console over a Virtio GPU device can be run
in combination with the serial SCLP console (default on S390).
The SCLP console can still be accessed by management applications
(eg: via Libvirt's virsh console).
Signed-off-by: Farhan Ali <alifm@linux.vnet.ibm.com>
Acked-by: Christian Borntraeger <borntraeger@de.ibm.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Message-Id: <e23b61f4f599ba23881727a1e8880e9d60cc6a48.1519315352.git.alifm@linux.vnet.ibm.com>
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The Linux Virtual Terminal (VT) layer provides a default keymap
which is compiled when VT layer is enabled. But at the same time
we are also compiling the EBCDIC keymap and this causes the linker
to complain.
So let's rename the EBCDIC keymap variables to prevent linker
conflict.
Signed-off-by: Farhan Ali <alifm@linux.vnet.ibm.com>
Acked-by: Christian Borntraeger <borntraeger@de.ibm.com>
Acked-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Message-Id: <f670a2698d2372e1e990c48a29334ffe894804b1.1519315352.git.alifm@linux.vnet.ibm.com>
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
The 'commit e25df1205f ("[S390] Kconfig: menus with depends on HAS_IOMEM.")'
added the HAS_IOMEM dependecy for "Graphics support". This disabled the
"Graphics support" menu for S390. But if we enable VT layer for S390,
we would also need to enable the dummy console. So let's remove the
HAS_IOMEM dependency.
Move this dependency to sub menu items and console drivers that use
io memory.
Signed-off-by: Farhan Ali <alifm@linux.vnet.ibm.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Message-Id: <6e8ef238162df5be4462126be155975c722e9863.1519315352.git.alifm@linux.vnet.ibm.com>
Acked-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
A case statement in kvm_s390_shadow_tables uses fallthrough annotations
which are not recognized by gcc because they are hidden within a block.
Move these annotations out of the block to fix (W=1) warnings like below:
arch/s390/kvm/gaccess.c: In function 'kvm_s390_shadow_tables':
arch/s390/kvm/gaccess.c:1029:26: warning: this statement may fall through [-Wimplicit-fallthrough=]
case ASCE_TYPE_REGION1: {
^
Signed-off-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
Reviewed-by: David Hildenbrand <david@redhat.com>
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
We want to count IO exit requests in kvm_stat. At the same time
we can get rid of the handle_noop function.
Reviewed-by: David Hildenbrand <david@redhat.com>
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
commit 35b3fde620 ("KVM: s390: wire up bpb feature") has no
documentation for KVM_CAP_S390_BPB. While adding this let's also add
other missing capabilities like KVM_CAP_S390_PSW, KVM_CAP_S390_GMAP and
KVM_CAP_S390_COW.
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
Reviewed-by: David Hildenbrand <david@redhat.com>
Reviewed-by: Janosch Frank <frankja@linux.vnet.ibm.com>
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
debug_objects_maxchecked is only updated in __debug_check_no_obj_freed(),
and only read in debug_objects_maxchecked, unfortunately both of these are
optional and depend on different Kconfig symbols.
When both CONFIG_DEBUG_OBJECTS_FREE and CONFIG_DEBUG_FS are disabled this
warning is emitted:
lib/debugobjects.c:56:14: error: 'debug_objects_maxchecked' defined but not used [-Werror=unused-variable]
Rather than trying to add more complex #ifdef protections, mark the
variable as __maybe_unused so it can be silently dropped when usused.
Fixes: bd9dcd0465 ("debugobjects: Export max loops counter")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Yang Shi <yang.shi@linux.alibaba.com>
Cc: Waiman Long <longman@redhat.com>
Link: https://lkml.kernel.org/r/20180313131857.158876-1-arnd@arndb.de
The #sound-dai-cells property may be required to reference the CPU DAI
properly. This change is required for Snow HDMI audio.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Reported-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
rvt_mregion uses percpu_ref for reference counting and RCU to protect
accesses from lkey_table. When a rvt_mregion needs to be freed, it
first gets unregistered from lkey_table and then rvt_check_refs() is
called to wait for in-flight usages before the rvt_mregion is freed.
rvt_check_refs() seems to have a couple issues.
* It has a fast exit path which tests percpu_ref_is_zero(). However,
a percpu_ref reading zero doesn't mean that the object can be
released. In fact, the ->release() callback might not even have
started executing yet. Proceeding with freeing can lead to
use-after-free.
* lkey_table is RCU protected but there is no RCU grace period in the
free path. percpu_ref uses RCU internally but it's sched-RCU whose
grace periods are different from regular RCU. Also, it generally
isn't a good idea to depend on internal behaviors like this.
To address the above issues, this patch removes the fast exit and adds
an explicit synchronize_rcu().
Signed-off-by: Tejun Heo <tj@kernel.org>
Acked-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Cc: Mike Marciniszyn <mike.marciniszyn@intel.com>
Cc: linux-rdma@vger.kernel.org
Cc: Linus Torvalds <torvalds@linux-foundation.org>
While converting ioctx index from a list to a table, db446a08c2
("aio: convert the ioctx list to table lookup v3") missed tagging
kioctx_table->table[] as an array of RCU pointers and using the
appropriate RCU accessors. This introduces a small window in the
lookup path where init and access may race.
Mark kioctx_table->table[] with __rcu and use the approriate RCU
accessors when using the field.
Signed-off-by: Tejun Heo <tj@kernel.org>
Reported-by: Jann Horn <jannh@google.com>
Fixes: db446a08c2 ("aio: convert the ioctx list to table lookup v3")
Cc: Benjamin LaHaise <bcrl@kvack.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: stable@vger.kernel.org # v3.12+
While fixing refcounting, e34ecee2ae ("aio: Fix a trinity splat")
incorrectly removed explicit RCU grace period before freeing kioctx.
The intention seems to be depending on the internal RCU grace periods
of percpu_ref; however, percpu_ref uses a different flavor of RCU,
sched-RCU. This can lead to kioctx being freed while RCU read
protected dereferences are still in progress.
Fix it by updating free_ioctx() to go through call_rcu() explicitly.
v2: Comment added to explain double bouncing.
Signed-off-by: Tejun Heo <tj@kernel.org>
Reported-by: Jann Horn <jannh@google.com>
Fixes: e34ecee2ae ("aio: Fix a trinity splat")
Cc: Kent Overstreet <kent.overstreet@gmail.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: stable@vger.kernel.org # v3.13+
The firmware loader code has grown quite a bit over the years.
The practice of stuffing everything we need into one file makes
the code hard to follow.
In order to split the firmware loader code into different components
we must pick a module name and a first object target file. We must
keep the firmware_class name to remain compatible with scripts which
have been relying on the sysfs loader path for years, so the old module
name stays. We can however rename the C file without affecting the
module name.
The firmware_class used to represent the idea that the code was a simple
sysfs firmware loader, provided by the struct class firmware_class.
The sysfs firmware loader used to be the default, today its only the
fallback mechanism.
This only renames the target code then to make emphasis of what the code
does these days. With this change new features can also use a new object
files.
Signed-off-by: Luis R. Rodriguez <mcgrof@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Now that we have a kconfig checker just use that instead of relying
on testing a sysfs directory being present, since our requirements
are spelled out.
Acked-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Luis R. Rodriguez <mcgrof@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When a kernel is not built with:
CONFIG_HAS_FW_LOADER_USER_HELPER_FALLBACK=y
We don't currently enable testing fw_fallback.sh. For kernels that
still enable the fallback mechanism, its possible to use the async
request firmware API call request_firmware_nowait() using the custom
interface to use the fallback mechanism, so we should be able to test
this but we currently cannot.
We can enable testing without CONFIG_HAS_FW_LOADER_USER_HELPER_FALLBACK=y
by relying on /proc/config.gz (CONFIG_IKCONFIG_PROC), if present. If you
don't have this we'll have no option but to rely on old heuristics for now.
We stuff the new kconfig_has() helper into our shared library as we'll
later expando on its use elsewhere.
Acked-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Luis R. Rodriguez <mcgrof@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>