Add support to request latency stats from firmware through HTT stats
type 25. These stats give information about count of transmitted and
received MAC Protocol Data Units(PDU) and Service Data Units(SDU)
and other latency stats.
Sample output:
-------------
echo 25 > /sys/kernel/debug/ath12k/pci-0000\:06\:00.0/mac0/htt_stats_type
cat /sys/kernel/debug/ath12k/pci-0000\:06\:00.0/mac0/htt_stats
HTT_STATS_LATENCY_CTX_TLV:
duration = 0
tx_msdu_cnt = 0
tx_mpdu_cnt = 0
rx_msdu_cnt = 0
rx_mpdu_cnt = 0
HTT_STATS_LATENCY_PROF_TLV:
Latency name = PROF_SCH_ENQ_TQM_CMDS
count = 0
minimum = 4294967295
maximum = 0
.....
HTT_STATS_LATENCY_CNT_TLV:
prof_enable_cnt = 39
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.4.1-00199-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0-03427-QCAHMTSWPL_V1.0_V2.0_SILICONZ-1.15378.4
Signed-off-by: Dinesh Karthikeyan <quic_dinek@quicinc.com>
Signed-off-by: Roopni Devanathan <quic_rdevanat@quicinc.com>
Link: https://patch.msgid.link/20250204064417.3671928-3-quic_rdevanat@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
The single split-phy PCI device can perform multi-link operation (MLO)
within its own radio, and the MLO-supporting firmware also supports MLO
for split-phy PCI devices.
Therefore, enable MLO for the single split-phy PCI device.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00173-QCAHKSWPL_SILICONZ-1
Signed-off-by: Aaradhana Sahu <quic_aarasahu@quicinc.com>
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Link: https://patch.msgid.link/20250207050327.360987-4-quic_aarasahu@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
The mlo_capable flag in structure ath12k_hw_group indicate that a device
is capable of operating in multi-link mode. Currently this is enabled
based on single_chip_mlo_support advertised by the firmware within
ath12k_qmi_phy_cap_send().
Since the firmware advertises multi-link operation (MLO) support through
the ATH12K_FW_FEATURE_MLO feature in firmware-2.bin, there is no need to
rely on the QMI phy capability (single_chip_mlo_support). Therefore remove
the dependency on single_chip_mlo_support to set mlo_capable flag.
Below is the impact on single split-phy PCI device with and without this
patch:
Note: This patch does not change the existing behavior of the single
split-phy PCI device.
1. Driver without this patch + firmware with single_chip_mlo_support
as false: MLO is not enabled.
2. Driver without this patch + firmware with single_chip_mlo_support
as true: MLO works fine.
3. Driver with this patch + firmware with single_chip_mlo_support as
false: MLO is not enabled.
4. Driver with this patch + firmware with single_chip_mlo_support as
true: MLO works fine.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00173-QCAHKSWPL_SILICONZ-1
Signed-off-by: Aaradhana Sahu <quic_aarasahu@quicinc.com>
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Link: https://patch.msgid.link/20250207050327.360987-3-quic_aarasahu@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
When multi-link operation(MLO) is enabled through follow-up patches in
the single split-phy device, the firmware expects hardware links
(hw_links) information from the driver.
If driver does not send WMI multi-link setup and ready command to the
firmware during MLO setup for single split-phy device, the firmware will
be unaware of the hw_links component of the multi-link operation. This may
lead to firmware assert during multi-link association.
Therefore, enable WMI setup, ready and teardown commands for single
split-phy PCI device.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00173-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Signed-off-by: Aaradhana Sahu <quic_aarasahu@quicinc.com>
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Link: https://patch.msgid.link/20250207050327.360987-2-quic_aarasahu@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
If ag->mutex has been locked, unlock it before returning. If it has not
been locked, do not unlock it before returning. These bugs have been
detected by the Clang thread-safety analyzer.
Cc: Karthikeyan Periyasamy <quic_periyasa@quicinc.com>
Cc: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Fixes: ee146e11b4 ("wifi: ath12k: refactor core start based on hardware group")
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Reviewed-by: Aditya Kumar Singh <aditya.kumar.singh@oss.qualcomm.com>
Link: https://patch.msgid.link/20250206221317.3845663-1-bvanassche@acm.org
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
For MLO netdevice, the broadcast frame should be transmitted with the
same sequence number on all the links.
Per IEEE 802.11be-2024 section 10.3.2.14.2 "Transmitter requirements",
An AP MLD shall use SNS11 in Table 10-5 (Transmitter sequence number
spaces) maintained by the MLD to determine the sequence number of a
group addressed data frame that is transmitted by an AP affiliated
with the AP MLD so that the same group addressed Data frame
transmitted over multiple links by the AP MLD uses the same
sequence number for transmission on each link.
Currently the MLO multicast handling is done in the mac80211 layer.
Enable support for handling MLO Multicast in the driver to update the
hardware descriptors in a custom way to handle the multicast frames.
Firmware expects the MLO multicast frames to the submitted to the
hardware with special vdev_id (actual vdev_id + 128) to recognize it as
a host inspected frame to avoid using the reinjected path and it also
uses the multicast global sequence number (GSN) provided by the host
in the HTT metadata to process and transmit it with the same sequence
number.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00173-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Signed-off-by: Balamurugan Mahalingam <quic_bmahalin@quicinc.com>
Reviewed-by: Aditya Kumar Singh <aditya.kumar.singh@oss.qualcomm.com>
Link: https://patch.msgid.link/20250203212647.2694566-3-quic_bmahalin@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Update the HTT_TCL_METADATA version to the latest version (2)
as the bit definitions have changed a little to support more
features. This new version allows the host to submit a packet with
more information to the firmware. Firmware uses this additional
information to do special processing for certain frames.
All the firmware binaries available in upstream/public are compatible with
this HTT version update.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00173-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Signed-off-by: Balamurugan Mahalingam <quic_bmahalin@quicinc.com>
Reviewed-by: Aditya Kumar Singh <aditya.kumar.singh@oss.qualcomm.com>
Link: https://patch.msgid.link/20250203212647.2694566-2-quic_bmahalin@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
ath11k_hal_srng_* should be used with srng->lock to protect srng data.
For ath11k_dp_rx_mon_dest_process() and ath11k_dp_full_mon_process_rx(),
they use ath11k_hal_srng_* for many times but never call srng->lock.
So when running (full) monitor mode, warning will occur:
RIP: 0010:ath11k_hal_srng_dst_peek+0x18/0x30 [ath11k]
Call Trace:
? ath11k_hal_srng_dst_peek+0x18/0x30 [ath11k]
ath11k_dp_rx_process_mon_status+0xc45/0x1190 [ath11k]
? idr_alloc_u32+0x97/0xd0
ath11k_dp_rx_process_mon_rings+0x32a/0x550 [ath11k]
ath11k_dp_service_srng+0x289/0x5a0 [ath11k]
ath11k_pcic_ext_grp_napi_poll+0x30/0xd0 [ath11k]
__napi_poll+0x30/0x1f0
net_rx_action+0x198/0x320
__do_softirq+0xdd/0x319
So add srng->lock for them to avoid such warnings.
Inorder to fetch the srng->lock, should change srng's definition from
'void' to 'struct hal_srng'. And initialize them elsewhere to prevent
one line of code from being too long. This is consistent with other ring
process functions, such as ath11k_dp_process_rx().
Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-03125-QCAHSPSWPL_V1_V2_SILICONZ_LITE-3.6510.30
Tested-on: QCN9074 hw1.0 PCI WLAN.HK.2.7.0.1-01744-QCAHKSWPL_SILICONZ-1
Fixes: d5c65159f2 ("ath11k: driver for Qualcomm IEEE 802.11ax devices")
Signed-off-by: Kang Yang <quic_kangyang@quicinc.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Link: https://patch.msgid.link/20241219110531.2096-3-quic_kangyang@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
While processing the monitor destination ring, MSDUs are reaped from the
link descriptor based on the corresponding buf_id.
However, sometimes the driver cannot obtain a valid buffer corresponding
to the buf_id received from the hardware. This causes an infinite loop
in the destination processing, resulting in a kernel crash.
kernel log:
ath11k_pci 0000:58:00.0: data msdu_pop: invalid buf_id 309
ath11k_pci 0000:58:00.0: data dp_rx_monitor_link_desc_return failed
ath11k_pci 0000:58:00.0: data msdu_pop: invalid buf_id 309
ath11k_pci 0000:58:00.0: data dp_rx_monitor_link_desc_return failed
Fix this by skipping the problematic buf_id and reaping the next entry,
replacing the break with the next MSDU processing.
Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-03125-QCAHSPSWPL_V1_V2_SILICONZ_LITE-3.6510.30
Tested-on: QCN9074 hw1.0 PCI WLAN.HK.2.7.0.1-01744-QCAHKSWPL_SILICONZ-1
Fixes: d5c65159f2 ("ath11k: driver for Qualcomm IEEE 802.11ax devices")
Signed-off-by: P Praneesh <quic_ppranees@quicinc.com>
Signed-off-by: Kang Yang <quic_kangyang@quicinc.com>
Acked-by: Kalle Valo <kvalo@kernel.org>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Link: https://patch.msgid.link/20241219110531.2096-2-quic_kangyang@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Currently, the link interface is deleted during channel unassignment, which
does not align with mac80211 link handling. Therefore, add changes to only
perform vdev stop during channel unassignment. The actual vdev deletion
will occur in change_vif_links().
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00173-QCAHKSWPL_SILICONZ-1
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00130-QCAHKSWPL_SILICONZ-1.97421.5 # Nicolas Escande
Signed-off-by: Aditya Kumar Singh <aditya.kumar.singh@oss.qualcomm.com>
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Tested-by: Nicolas Escande <nico.escande@gmail.com>
Link: https://patch.msgid.link/20250204-unlink_link_arvif_from_chanctx-v2-8-764fb5973c1a@oss.qualcomm.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Currently, links in an interface are allocated during channel assignment
via assign_vif_chanctx(). Conversely, links are deleted during channel
unassignment via unassign_vif_chanctx(). However, deleting links during
channel unassignment does not comply with mac80211 link handling.
Therefore, this process should be managed within change_vif_links(). To
maintain symmetry, link addition should also be handled in
change_vif_links().
Hence, add changes to allocate link arvif in change_vif_links(). Creating
the link interface on firmware will still be done during channel
assignment.
And since link will be created but channel might not be assigned, there is
a need now to test is_created flag in ath12k_mac_mlo_get_vdev_args() before
accessing link_conf or else link bring up will fail.
A subsequent change will handle link removal part.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00173-QCAHKSWPL_SILICONZ-1
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00130-QCAHKSWPL_SILICONZ-1.97421.5 # Nicolas Escande
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Signed-off-by: Aditya Kumar Singh <aditya.kumar.singh@oss.qualcomm.com>
Tested-by: Nicolas Escande <nico.escande@gmail.com>
Link: https://patch.msgid.link/20250204-unlink_link_arvif_from_chanctx-v2-7-764fb5973c1a@oss.qualcomm.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
An upcoming change will invoke ath12k_mac_init_arvif(),
ath12k_mac_assign_link_vif(), ath12k_mac_unassign_link_vif(), and
ath12k_mac_remove_link_interface() from a line located above their current
definition. Hence, relocate these functions to above so that these can be
invoked later on.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00130-QCAHKSWPL_SILICONZ-1.97421.5 # Nicolas Escande
Signed-off-by: Aditya Kumar Singh <aditya.kumar.singh@oss.qualcomm.com>
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Tested-by: Nicolas Escande <nico.escande@gmail.com>
Link: https://patch.msgid.link/20250204-unlink_link_arvif_from_chanctx-v2-6-764fb5973c1a@oss.qualcomm.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Currently, in ath12k_mac_set_key(), if sta is not present, the address is
retrieved from link_conf's bssid or addr member, depending on the interface
type.
When operating as an ML station and during shutdown, link_conf will not be
available. This can result in the following error:
ath12k_pci 0004:01:00.0: unable to access bss link conf in set key for vif AA:BB:CC:DD:EE:FF link 1
The primary purpose of accessing link_conf is to obtain the address for
finding the peer. However, since arvif is always valid in this call, it can
be used instead.
Add change to use arvif instead of link_conf.
A subsequent change will expose this issue but since tear down will give
error, this is included first.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00173-QCAHKSWPL_SILICONZ-1
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00130-QCAHKSWPL_SILICONZ-1.97421.5 # Nicolas Escande
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Signed-off-by: Aditya Kumar Singh <aditya.kumar.singh@oss.qualcomm.com>
Tested-by: Nicolas Escande <nico.escande@gmail.com>
Link: https://patch.msgid.link/20250204-unlink_link_arvif_from_chanctx-v2-5-764fb5973c1a@oss.qualcomm.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
The current logic for initializing arvif is present in both the add
interface operation callback and ath12k_mac_assign_link_vif(). The former
handles deflink initialization, while the latter is responsible for other
links. This redundancy could be avoided by using a common helper function.
Hence, add a new helper ath12k_mac_init_arvif() which initializes a
given arvif.
Since synchronizing rcu is not required after adding a rcu pointer, remove
that now.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00173-QCAHKSWPL_SILICONZ-1
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00130-QCAHKSWPL_SILICONZ-1.97421.5 # Nicolas Escande
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Signed-off-by: Aditya Kumar Singh <aditya.kumar.singh@oss.qualcomm.com>
Tested-by: Nicolas Escande <nico.escande@gmail.com>
Link: https://patch.msgid.link/20250204-unlink_link_arvif_from_chanctx-v2-4-764fb5973c1a@oss.qualcomm.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Currently, vif level settings are done in ath12k_mac_assign_link_vif() as
well as in ath12k_mac_op_add_interface(). Since it is vif level settings,
doing this on per link does not make sense and it contributes to redundant
code. Get rid of this redundant code from ath12k_mac_assign_link_vif().
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00173-QCAHKSWPL_SILICONZ-1
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00130-QCAHKSWPL_SILICONZ-1.97421.5 # Nicolas Escande
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Signed-off-by: Aditya Kumar Singh <aditya.kumar.singh@oss.qualcomm.com>
Tested-by: Nicolas Escande <nico.escande@gmail.com>
Link: https://patch.msgid.link/20250204-unlink_link_arvif_from_chanctx-v2-3-764fb5973c1a@oss.qualcomm.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
There might be instances where ath12k_dbg() is needed, but access to
struct ath12k_base (ab) is not readily available. To address this, add
support to print the debug message using printk() when ab is not present.
To avoid the need to explicitly pass NULL each time, introduce a new macro
ath12k_generic_dbg() which resolves to ath12k_dbg() with ab set to NULL.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00173-QCAHKSWPL_SILICONZ-1
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00130-QCAHKSWPL_SILICONZ-1.97421.5 # Nicolas Escande
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Signed-off-by: Aditya Kumar Singh <aditya.kumar.singh@oss.qualcomm.com>
Tested-by: Nicolas Escande <nico.escande@gmail.com>
Link: https://patch.msgid.link/20250204-unlink_link_arvif_from_chanctx-v2-2-764fb5973c1a@oss.qualcomm.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
The current implementation includes a debug mask check both in the macro
expansion and in the function __ath12k_dbg(), which is unnecessary.
Simplify the code by removing the redundant check from the helper function
__ath12k_dbg().
While at this, rename the first argument in macro from ar to ab since the
first argument name in the function __ath12k_dbg() is ab.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00173-QCAHKSWPL_SILICONZ-1
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00130-QCAHKSWPL_SILICONZ-1.97421.5 # Nicolas Escande
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Signed-off-by: Aditya Kumar Singh <aditya.kumar.singh@oss.qualcomm.com>
Tested-by: Nicolas Escande <nico.escande@gmail.com>
Link: https://patch.msgid.link/20250204-unlink_link_arvif_from_chanctx-v2-1-764fb5973c1a@oss.qualcomm.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Currently, peer rate table information involves complex computation for
the rate index to update the rate table. To simplify this process, avoid
the rate index calculation by defining the rate table with bandwidth, GI,
NSS, MCS. Therefore, update the rate information based on the bandwidth,
GI, NSS and MCS information from the TLV data of monitor status Rx path.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00173-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Signed-off-by: Balamurugan Mahalingam <quic_bmahalin@quicinc.com>
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Signed-off-by: Karthikeyan Periyasamy <quic_periyasa@quicinc.com>
Link: https://patch.msgid.link/20250206013854.174765-9-quic_periyasa@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Currently, EHT MCS information is not populated. Therefore, add the EHT
MCS counter array to the peer rate statistics and update the EHT MCS
statistics from the status TLV data in the monitor Rx path. In the future,
this information will be used in the peer extended Rx statistics dump.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00173-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Signed-off-by: Balamurugan Mahalingam <quic_bmahalin@quicinc.com>
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Signed-off-by: Karthikeyan Periyasamy <quic_periyasa@quicinc.com>
Link: https://patch.msgid.link/20250206013854.174765-8-quic_periyasa@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Currently, ampdu id is update with peer id mask which is incorrect.
Therefore, update the ampdu id with PPDU id mask value. Also move
the ampdu_id field inside the user stats since it is a user id based
statistics.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00173-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Signed-off-by: P Praneesh <quic_ppranees@quicinc.com>
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Signed-off-by: Karthikeyan Periyasamy <quic_periyasa@quicinc.com>
Link: https://patch.msgid.link/20250206013854.174765-7-quic_periyasa@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Currently, peer id get reported in the PPDU end user TLV tag. But the
monitor status handler is inherited from ath11k, but it was not updated
to incorporate the changes made to ath12k 802.11be hardware architecture.
Therefore, update the peer id from the PPDU end user TLV data to get latest
peer id update, it helps to populate accurate peer information on the
statistics data.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00173-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Co-developed-by: P Praneesh <quic_ppranees@quicinc.com>
Signed-off-by: P Praneesh <quic_ppranees@quicinc.com>
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Signed-off-by: Karthikeyan Periyasamy <quic_periyasa@quicinc.com>
Link: https://patch.msgid.link/20250206013854.174765-6-quic_periyasa@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Currently, monitor is not enabled. However, in the future, the monitor
will be enabled. Therefore, add the necessary HAL_PHYRX_OTHER_RECEIVE_INFO
TLV parsing support in the monitor Rx path, which helps to populate the
extended Rx statistics.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00173-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Co-developed-by: P Praneesh <quic_ppranees@quicinc.com>
Signed-off-by: P Praneesh <quic_ppranees@quicinc.com>
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Signed-off-by: Karthikeyan Periyasamy <quic_periyasa@quicinc.com>
Link: https://patch.msgid.link/20250206013854.174765-5-quic_periyasa@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Currently, monitor is not enabled. However, in the future, the monitor
will be enabled. Therefore, add necessary HAL_RX_PPDU_START_USER_INFO TLV
parsing support in monitor Rx path, which help to populate the EHT radiotap
data.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00173-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Co-developed-by: P Praneesh <quic_ppranees@quicinc.com>
Signed-off-by: P Praneesh <quic_ppranees@quicinc.com>
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Signed-off-by: Karthikeyan Periyasamy <quic_periyasa@quicinc.com>
Link: https://patch.msgid.link/20250206013854.174765-4-quic_periyasa@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Currently, monitor is not enabled. However, in the future, the monitor
will be enabled. Therefore, add the necessary HAL_PHYRX_GENERIC_EHT_SIG
TLV parsing support in monitor Rx path, which help to populate the EHT
radiotap data.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00173-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Co-developed-by: P Praneesh <quic_ppranees@quicinc.com>
Signed-off-by: P Praneesh <quic_ppranees@quicinc.com>
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Signed-off-by: Karthikeyan Periyasamy <quic_periyasa@quicinc.com>
Link: https://patch.msgid.link/20250206013854.174765-3-quic_periyasa@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Currently, monitor is not enabled. However, in the future, the monitor
will be enabled. Therefore, add the necessary HAL_PHYRX_GENERIC_U_SIG TLV
parsing support in monitor Rx path, which help to populate the EHT
radiotap data.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00173-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Co-developed-by: P Praneesh <quic_ppranees@quicinc.com>
Signed-off-by: P Praneesh <quic_ppranees@quicinc.com>
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Signed-off-by: Karthikeyan Periyasamy <quic_periyasa@quicinc.com>
Link: https://patch.msgid.link/20250206013854.174765-2-quic_periyasa@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
This adds support for reporting to the kernel the average rssi. This is
done the same way as it was done in ath11k. A simple ewma (with the same
parameters) is updated with each rssi update.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00173-QCAHKSWPL_SILICONZ-1
Signed-off-by: Nicolas Escande <nico.escande@gmail.com>
Reviewed-by: Aditya Kumar Singh <aditya.kumar.singh@oss.qualcomm.com>
Link: https://patch.msgid.link/20250201211301.357985-1-nico.escande@gmail.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
With previous patch "wifi: ath11k: move update channel list from update
reg worker to reg notifier", ath11k_reg_update_chan_list() will be
called during reg_process_self_managed_hint().
reg_process_self_managed_hint() will hold rtnl_lock all the time.
But ath11k_reg_update_chan_list() may increase the occupation time of
rtnl_lock, because when wait flag is set, wait_for_completion_timeout()
will be called during 11d/hw scan.
Should minimize the occupation time of rtnl_lock as much as possible
to avoid interfering with rest of the system. So move the update channel
list operation to a new worker, so that wait_for_completion_timeout()
won't be called and will not increase the occupation time of rtnl_lock.
Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-03125-QCAHSPSWPL_V1_V2_SILICONZ_LITE-3
Signed-off-by: Wen Gong <quic_wgong@quicinc.com>
Co-developed-by: Kang Yang <quic_kangyang@quicinc.com>
Signed-off-by: Kang Yang <quic_kangyang@quicinc.com>
Reviewed-by: Aditya Kumar Singh <quic_adisi@quicinc.com>
Link: https://patch.msgid.link/20250117061737.1921-3-quic_kangyang@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Currently when ath11k gets a new channel list, it will be processed
according to the following steps:
1. update new channel list to cfg80211 and queue reg_work.
2. cfg80211 handles new channel list during reg_work.
3. update cfg80211's handled channel list to firmware by
ath11k_reg_update_chan_list().
But ath11k will immediately execute step 3 after reg_work is just
queued. Since step 2 is asynchronous, cfg80211 may not have completed
handling the new channel list, which may leading to an out-of-bounds
write error:
BUG: KASAN: slab-out-of-bounds in ath11k_reg_update_chan_list
Call Trace:
ath11k_reg_update_chan_list+0xbfe/0xfe0 [ath11k]
kfree+0x109/0x3a0
ath11k_regd_update+0x1cf/0x350 [ath11k]
ath11k_regd_update_work+0x14/0x20 [ath11k]
process_one_work+0xe35/0x14c0
Should ensure step 2 is completely done before executing step 3. Thus
Wen raised patch[1]. When flag NL80211_REGDOM_SET_BY_DRIVER is set,
cfg80211 will notify ath11k after step 2 is done.
So enable the flag NL80211_REGDOM_SET_BY_DRIVER then cfg80211 will
notify ath11k after step 2 is done. At this time, there will be no
KASAN bug during the execution of the step 3.
[1] https://patchwork.kernel.org/project/linux-wireless/patch/20230201065313.27203-1-quic_wgong@quicinc.com/
Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-03125-QCAHSPSWPL_V1_V2_SILICONZ_LITE-3
Fixes: f45cb6b29c ("wifi: ath11k: avoid deadlock during regulatory update in ath11k_regd_update()")
Signed-off-by: Wen Gong <quic_wgong@quicinc.com>
Signed-off-by: Kang Yang <quic_kangyang@quicinc.com>
Reviewed-by: Aditya Kumar Singh <quic_adisi@quicinc.com>
Link: https://patch.msgid.link/20250117061737.1921-2-quic_kangyang@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Host receives four Transmit Power Control(TPC) events from firmware on
sending TPC request. Fixed param TLV is present as part of all event to
indicate the event count and end of event. TPC config parameters along
with regulatory power array comes as first event. Rates array comes as
second and third event as it cannot be packed in single event.
Conformance Test Limit (CTL) power array comes as the fourth event.
Firmware packs different sets of array params which includes array
length and type inside master TLV as different subtlvs. And the actual
content of array is packed one after the other inside a separate TLV as
single buffer.
Parse various events and save it in local structures. Create tpc_stats
file using debugfs to store these local structures. Create function to
handle TPC stats read to relay the information to the user.
Command usage:
cat > /sys/kernel/debug/ath12k/pci-0000\:06\:00.0/mac0/tpc_stats
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.1.1-00214-QCAHKSWPL_SILICONZ-1
Signed-off-by: Sowmiya Sree Elavalagan <quic_ssreeela@quicinc.com>
Co-developed-by: Ramya Gnanasekar <quic_rgnanase@quicinc.com>
Signed-off-by: Ramya Gnanasekar <quic_rgnanase@quicinc.com>
Co-developed-by: Roopni Devanathan <quic_rdevanat@quicinc.com>
Signed-off-by: Roopni Devanathan <quic_rdevanat@quicinc.com>
Reviewed-by: Aditya Kumar Singh <aditya.kumar.singh@oss.qualcomm.com>
Link: https://patch.msgid.link/20250130061104.962124-2-quic_rdevanat@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Current code in ath11k_mac_set_txbf_conf overrides nsts, which is
incorrect as it confuses nss and nsts. nss is Number of Spatial
Streams，nsts is Number of Space-Time Streams.
As mentioned in Fixes: 55b5ee3357, the nss used when acting as a
beamformee in VHT mode should be reported by the firmware and should not
be greater than the number of receiving antennas - 1. The num_rx_chains
related nss rather than nsts.
If STBC is enabled, nsts is greater than nss. About nss are mapped to
nsts, refer to IEEE Std 802.11-2020: 19.3.11.9.2 Space-time block coding
(STBC), Table 19-18—Constellation mapper output to spatial mapper input
for STBC.
Remove wrong overriding for nsts of VHT Beamformee STS Capability,
acting DL MU-MIMO in VHT mode is working properly.
Tested-on: WCN6855 hw2.1 PCI WLAN.HSP.1.1-04479-QCAHSPSWPL_V1_V2_SILICONZ_IOE-1
Fixes: 55b5ee3357 ("wifi: ath11k: fix number of VHT beamformee spatial streams")
Signed-off-by: Yu Zhang (Yuriy) <quic_yuzha@quicinc.com>
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Link: https://patch.msgid.link/20250124075953.2282354-1-quic_yuzha@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
The current code does not have the MU EDCA feature, so it cannot support
the use of EDCA by STA in specific UL MU HE TB PPDU transmissions. Refer
to IEEE Std 802.11ax-2021 "9.4.2.251 MU EDCA Parameter Set element",
"26.2.7 EDCA operation using MU EDCA parameters".
Add ath11k_mac_op_conf_tx_mu_edca() to construct the MU EDCA parameters
received from mac80211 into WMI WMM parameters，and send to the firmware
according to the different WMM type flags.
Tested-on: WCN6855 hw2.1 PCI WLAN.HSP.1.1-04523-QCAHSPSWPL_V1_V2_SILICONZ_IOE-1
Signed-off-by: Yu Zhang (Yuriy) <quic_yuzha@quicinc.com>
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Link: https://patch.msgid.link/20250124061343.2263467-1-quic_yuzha@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Currently, ath12k does not support reading variant from ACPI board data
filename extension for downloading board data file.
To address this issue, obtain the string of the ACPI data filename
extension and use it as part of the string to search for the board data
file from board-2.bin.
This patch will not affect QCN9274, because only WCN7850 supports ACPI.
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Signed-off-by: Lingbo Kong <quic_lingbok@quicinc.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Link: https://patch.msgid.link/20250113074810.29729-5-quic_lingbok@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Currently, the timing for accessing the ACPI table is inappropriate.
Due to special ACPI requirements, the ACPI table must be obtained before
downloading the board data file. Therefore, adjust the timing for accessing
the ACPI table accordingly.
This patch will not affect QCN9274, because only WCN7850 supports ACPI.
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Signed-off-by: Lingbo Kong <quic_lingbok@quicinc.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Link: https://patch.msgid.link/20250113074810.29729-4-quic_lingbok@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Currently, ath12k does not support enable or disable specific features by
ACPI bitflag.
To address this issue, obtain the ACPI bitflag value and use it to
selectively enable or disable specific features.
This patch will not affect QCN9274, because only WCN7850 supports ACPI.
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Signed-off-by: Lingbo Kong <quic_lingbok@quicinc.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Link: https://patch.msgid.link/20250113074810.29729-3-quic_lingbok@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Currently, ath12k does not support obtaining the buffer type ACPI function
bitmap.
To solve this issue, change the code to support obtaining the buffer type
ACPI function bitmap.
This patch will not affect QCN9274, because only WCN7850 supports ACPI.
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Signed-off-by: Lingbo Kong <quic_lingbok@quicinc.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Link: https://patch.msgid.link/20250113074810.29729-2-quic_lingbok@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Currently ath12k_mac_ieee80211_sta_bw_to_wmi() handles the bandwidth from
sta's deflink member. This works only for non-ML station. Now that MLO
support is there, extend this function to use link sta instead of deflink.
Additionally, in ath12k_mac_handle_link_sta_state(), the link sta structure
is not accessible, making it difficult to fetch the bandwidth there.
However, ath12k_mac_station_assoc() does reference the link sta structure.
Therefore, move the initial assignment of the arsta bandwidth member to
ath12k_mac_station_assoc().
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00173-QCAHKSWPL_SILICONZ-1
Signed-off-by: Aditya Kumar Singh <quic_adisi@quicinc.com>
Acked-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Link: https://patch.msgid.link/20250110-fix_link_sta_bandwidth_update-v1-2-61b6f3ef2ea3@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
An upcoming change will invoke ath12k_mac_ieee80211_sta_bw_to_wmi() from a
line located above its current definition. Hence, relocate it to above
so that it can be invoked later on.
No functionality changes. Compile tested only.
Signed-off-by: Aditya Kumar Singh <quic_adisi@quicinc.com>
Acked-by: Kalle Valo <kvalo@kernel.org>
Acked-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Link: https://patch.msgid.link/20250110-fix_link_sta_bandwidth_update-v1-1-61b6f3ef2ea3@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
In case of MHI error a reset work will be queued which will try
napi_disable() after napi_synchronize().
As the napi will be only enabled after qmi_firmware_ready event,
trying napi_synchronize() before napi_enable() will result in
indefinite sleep in case of a firmware crash in QMI init sequence.
To avoid this, introduce napi_enabled flag to check if napi is enabled
or not before calling napi_synchronize().
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00173-QCAHKSWPL_SILICONZ-1
Signed-off-by: Avula Sri Charan <quic_asrichar@quicinc.com>
Signed-off-by: Tamizh Chelvam Raja <quic_tamizhr@quicinc.com>
Reviewed-by: Aditya Kumar Singh <aditya.kumar.singh@oss.qualcomm.com>
Link: https://patch.msgid.link/20250124090058.3194299-1-quic_tamizhr@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Currently, when the driver receives a channel switch count WMI event from
the firmware with a count greater than 1, it calls
ieee80211_beacon_update_cntdwn(). If the beacon transmission fails, the
event will be received again with the previous count value. In this
scenario, the host decrements the mac80211 counter again, causing it to
move ahead of the firmware counter. Ultimately, when the firmware count
reaches 1, the mac80211 counter will reach zero, triggering a
WARN_ON_ONCE(). Therefore, there is a need to check the count value in the
event.
Hence to fix this, maintain the current ongoing counter in arvif. If the
count in the event does not match the expected value, silently discard the
event.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00173-QCAHKSWPL_SILICONZ-1
Signed-off-by: Aditya Kumar Singh <quic_adisi@quicinc.com>
Link: https://patch.msgid.link/20250124-ath12k_mlo_csa-v2-4-420c42fcfecf@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
At present, the driver configures the firmware to send the Channel Switch
(CS) count event only when the count reaches zero during a Channel Switch
Announcement (CSA). For frames managed by the upper layer, where the driver
does not update the counter, the CS count in these frames remains unchanged
throughout the entire CSA period. This is because the upper layer is not
aware of the latest ongoing count. Indicating same count value throughout
the CSA time is wrong and could lead to connection instabilities.
Fix this by configuring firmware to send CS count event for every count and
then accordingly decrementing the count in mac80211.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00173-QCAHKSWPL_SILICONZ-1
Signed-off-by: Aditya Kumar Singh <quic_adisi@quicinc.com>
Link: https://patch.msgid.link/20250124-ath12k_mlo_csa-v2-3-420c42fcfecf@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
The driver is informed of the counter offsets in the beacon during CSA
through the ieee80211_mutable_offsets structure. According to the
documentation for the cntdwn_counter_offs member, "This array can contain
zero values which should be ignored." However, the current implementation
uses these values unconditionally, without checking for zeros.
Whenever CSA is active, these offsets are guaranteed to be set. Therefore,
add a check for CSA active status before setting the CSA switch count
offsets. This ensures that the offsets are only set when CSA is active,
preventing incorrect configurations.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00173-QCAHKSWPL_SILICONZ-1
Signed-off-by: Aditya Kumar Singh <quic_adisi@quicinc.com>
Link: https://patch.msgid.link/20250124-ath12k_mlo_csa-v2-2-420c42fcfecf@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
The current code has ath12k_wmi_bcn_tmpl() accepting separate ar and
vdev_id parameters. However, ath12k_link_vif structure can be used to
derive both of these.
Hence, simplify the function signature.
Later change needs arvif pointer access within the function hence it is
better if arvif is directly passed now.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00173-QCAHKSWPL_SILICONZ-1
Signed-off-by: Aditya Kumar Singh <quic_adisi@quicinc.com>
Link: https://patch.msgid.link/20250124-ath12k_mlo_csa-v2-1-420c42fcfecf@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Currently in ath12k_mac_op_sta_statistics() there is the following
logic:
if (!arsta->txrate.legacy && !arsta->txrate.nss)
return;
Because ath12k_sta_statistics is used to report many info to iw wlan0 link,
if it return for empty legacy and nss of arsta->txrate, then the other
stats after it will not be set.
To address this issue remove the return and instead invert the logic to set
the txrate logic if (arsta->txrate.legacy || arsta->txrate.nss).
The same was done also in both ath10k with commit 1cd6ba8ae3 ("ath10k:
remove return for NL80211_STA_INFO_TX_BITRATE") and ath11k as well with
commit 1d795645e1 ("ath11k: remove return for empty tx bitrate in
mac_op_sta_statistics").
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00173-QCAHKSWPL_SILICONZ-1
Signed-off-by: Remi Pommarel <repk@triplefau.lt>
Reviewed-by: Aditya Kumar Singh <aditya.kumar.singh@oss.qualcomm.com>
Link: https://patch.msgid.link/38c2a7c4f7eaf57b9306bb95a9e6c42b7d987e05.1738169458.git.repk@triplefau.lt
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
