The driver may sleep under a spin lock, and the function call path is:
snd_ivtv_pcm_hw_free (acquire the lock by spin_lock_irqsave)
vfree --> may sleep
To fix it, the "substream->runtime->dma_area" is passed to a temporary
value, and mark it NULL when holding the lock. The memory is freed by
vfree through the temporary value outside the lock holding.
Signed-off-by: Jia-Ju Bai <baijiaju1990@163.com>
[hans.verkuil@cisco.com: removed unnecessary 'if (dma_area)']
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The current driver has a handful of hard-coded assumptions based on its
primary use for capture of video signals. Cleanup those assumptions,
and also query the subdev for format information and use that if
available.
Tested with 10-bit raw bayer input (SGRBG10) using the aptina,mt9v032
sensor, and also tested that composite video input still works from
ti,tvp514x decoder. Both tests done on the da850-evm board with the
add-on UI board.
NOTE: Will need further testing for other sensors with different bus
formats.
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Enable getting of subdevs from DT ports and endpoints.
The _get_pdata() function was larely inspired by (i.e. stolen from)
am437x-vpfe.c
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Capture driver silently overrides pixel format with a hack (according to
the comments) to pass v4l2 compliance tests. This isn't needed for
normal functionality, and works for composite video and raw camera capture
without.
In addition, the hack assumes that it only supports raw capture with a
single format (SBGGR8) which isn't true. VPIF can also capture 10- and
12-bit raw formats as well. Forthcoming patches will enable VPIF
input with raw-camera support and has been tested with 10-bit format
from the aptina,mt9v032 sensor.
Any compliance failures should be fixed with a real fix.
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
hard disk IO latency varies a lot depending on spindle move. The latency
range could be from several microseconds to several milliseconds. It's
pretty hard to get the baseline latency used by io.low.
We will use a different stragety here. The idea is only using IO with
spindle move to determine if cgroup IO is in good state. For HD, if io
latency is small (< 1ms), we ignore the IO. Such IO is likely from
sequential IO, and is helpless to help determine if a cgroup's IO is
impacted by other cgroups. With this, we only account IO with big
latency. Then we can choose a hardcoded baseline latency for HD (4ms,
which is typical IO latency with seek). With all these settings, the
io.low latency works for both HD and SSD.
Signed-off-by: Shaohua Li <shli@fb.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
This patch clean up a bit the platform definition block in
a way to avoid duplications and to let clear that GT3 for
the current platform only have the extra Media engine (BSD2).
v2: Kabylake IS_KABYLAKE as Anusha noticed.
v3: Avoid EXTRA_ENGINE_MASK and list rings out on GT3 to
make it more clear.
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Anusha Srivatsa <anusha.srivatsa@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Anusha Srivatsa <anusha.srivatsa@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1496765166-7068-1-git-send-email-rodrigo.vivi@intel.com
Let's be picky and just use PICK directly.
So we can extend this later without creating
a new PORT_X por every new number of ports we
have to handle.
Cc: Manasi Navare <manasi.d.navare@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Manasi Navare <manasi.d.navare@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1496700722-13755-1-git-send-email-rodrigo.vivi@intel.com
This patch set each gpio controller as a interrupt controller. User who
wants to use gpio as interrupt will have choice to use either "gpiolib"
interface or "common" interrupt interface.
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Alexandre TORGUE <alexandre.torgue@st.com>
The guest-linear address field is set for VM exits due to attempts to
execute LMSW with a memory operand and VM exits due to attempts to
execute INS or OUTS for which the relevant segment is usable,
regardless of whether or not EPT is in use.
Fixes: 119a9c01a5 ("KVM: nVMX: pass valid guest linear-address to the L1")
Signed-off-by: Jim Mattson <jmattson@google.com>
Signed-off-by: Radim Krčmář <rkrcmar@redhat.com>
The XSS-exiting bitmap is a VMCS control field that does not change
while the CPU is in non-root mode. Transferring the unchanged value
from vmcs02 to vmcs12 is unnecessary.
Signed-off-by: Jim Mattson <jmattson@google.com>
Signed-off-by: Radim Krčmář <rkrcmar@redhat.com>
The workaround added in
commit c6782b76d3 ("drm/i915/gen9: Reset secondary power well
equests left on by DMC/KVMR")
needs to be applied on Cannonlake as well.
So let's assume any platform using this power well setup
will also need and let's just go ahead and remove if condition.
Cc: Imre Deak <imre.deak@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1496781040-20888-11-git-send-email-rodrigo.vivi@intel.com
CNL power wells are very similar to SKL, with the exception that the
misc IO well has been split into separate AUX IO wells.
Not sure if DMC is supposed to manage the AUX wells for us or not.
Let's assume so for now.
v2: DDI A power well wants DDI A domains, not DDI B domains
v3: s/BIT/BIT_ULL and add proper Aux IO domains. (Rodrigo)
v4: Remove PW_DDI_E. Not supported on Current CNL SKUs. (Rodrigo).
v5: Removed DDI_E_IO_DOMAINS and moved PORT_DDI_E_IO to DDI_A_IO
for the same reasons as v4 when we found out that current CNL
SKUs don't have the full port E split.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1496781040-20888-10-git-send-email-rodrigo.vivi@intel.com
Indirect Context Offset Pointer has changed for Cannonlake.
INDIRECT_CTX_OFFSET[15:6] valid value for CNL is 19h per Spec.
v2: rebased to intel_lr_indirect_ctx_offset
v3: Commit message added per Tvrtko request.
Signed-off-by: Michel Thierry <michel.thierry@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1496781040-20888-9-git-send-email-rodrigo.vivi@intel.com
All registers and default configuration are the same for Skylake
and Cannonlake.
v2: Don't apply Wa for platforms without MOCS. (Paulo)
v3: Removed WaDisableSkipCaching that Joonas noticed that
according to spec it is not applicable to CNL.
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1496781040-20888-8-git-send-email-rodrigo.vivi@intel.com
Bits 11:2 must be zero and the linear addess in bits 63:12 must be
canonical. Otherwise, WRMSR(BNDCFGS) should raise #GP.
Fixes: 0dd376e709 ("KVM: x86: add MSR_IA32_BNDCFGS to msrs_to_save")
Signed-off-by: Jim Mattson <jmattson@google.com>
Signed-off-by: Radim Krčmář <rkrcmar@redhat.com>
Platform enabling and its power-on are organized in different
skus (U x Y x S x H, etc). So instead of organizing it in
GT1 x GT2 x GT3 let's also use the platform sku.
This is also the new Spec style what makes the review much
more easy and straightforward.
v2: Really include the PCI IDs to the picidlist[];
v3: Remove PCI IDs not present in spec.
v4: Rebase.
Signed-off-by: Anusha Srivatsa <anusha.srivatsa@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Clinton Taylor <clinton.a.taylor@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1496781040-20888-3-git-send-email-rodrigo.vivi@intel.com
The BNDCFGS MSR should only be exposed to the guest if the guest
supports MPX. (cf. the TSC_AUX MSR and RDTSCP.)
Fixes: 0dd376e709 ("KVM: x86: add MSR_IA32_BNDCFGS to msrs_to_save")
Change-Id: I3ad7c01bda616715137ceac878f3fa7e66b6b387
Signed-off-by: Jim Mattson <jmattson@google.com>
Signed-off-by: Radim Krčmář <rkrcmar@redhat.com>
The MSR permission bitmaps are shared by all VMs. However, some VMs
may not be configured to support MPX, even when the host does. If the
host supports VMX and the guest does not, we should intercept accesses
to the BNDCFGS MSR, so that we can synthesize a #GP
fault. Furthermore, if the host does not support MPX and the
"ignore_msrs" kvm kernel parameter is set, then we should intercept
accesses to the BNDCFGS MSR, so that we can skip over the rdmsr/wrmsr
without raising a #GP fault.
Fixes: da8999d318 ("KVM: x86: Intel MPX vmx and msr handle")
Signed-off-by: Jim Mattson <jmattson@google.com>
Signed-off-by: Radim Krčmář <rkrcmar@redhat.com>
Cannonlake is a Intel® Processor containing Intel® HD Graphics
following Kabylake.
It is Gen10.
Let's start by adding the platform definition based on previous
platforms but yet as alpha_support.
On following patches we will start adding PCI IDs and the
platform specific changes.
CNL has an increased DDB size as Damien had previously
noticed and provided a separated patch that got squashed here.
v2: Squash DDB size here per Ander request.
Credits-to: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Ander Conselvan de Oliveira <conselvan2@gmail.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1496781040-20888-1-git-send-email-rodrigo.vivi@intel.com
While introducing HDMI support, component matching on connectors node
were bypassed since no driver would actually bind on the DT node.
But when only a CVBS connector is present, only a single node is found
in the graph, but ignored and a NULL match table is given to the
component code.
This code permits bypassing the components framework by binding directly
the DRM driver when no components needs to be loaded.
Fixes: a41e82e6c4 ("drm/meson: Add support for components")
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Link: http://patchwork.freedesktop.org/patch/msgid/1496067352-8733-1-git-send-email-narmstrong@baylibre.com
I have encountered a NULL pointer dereference in
throtl_schedule_pending_timer:
[ 413.735396] BUG: unable to handle kernel NULL pointer dereference at 0000000000000038
[ 413.735535] IP: [<ffffffff812ebbbf>] throtl_schedule_pending_timer+0x3f/0x210
[ 413.735643] PGD 22c8cf067 PUD 22cb34067 PMD 0
[ 413.735713] Oops: 0000 [#1] SMP
......
This is caused by the following case:
blk_throtl_bio
throtl_schedule_next_dispatch <= sq is top level one without parent
throtl_schedule_pending_timer
sq_to_tg(sq)->td->throtl_slice <= sq_to_tg(sq) returns NULL
Fix it by using sq_to_td instead of sq_to_tg(sq)->td, which will always
return a valid td.
Fixes: 297e3d8547 ("blk-throttle: make throtl_slice tunable")
Signed-off-by: Joseph Qi <qijiang.qj@alibaba-inc.com>
Reviewed-by: Shaohua Li <shli@fb.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
Both the IMX51 and IMX53 datasheet indicates that the MIB counters
should be cleared during setup. Otherwise random numbers are returned
via ethtool -S. Add a quirk and a function to do this.
Tested on an IMX51.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We've run into kconfig missing dependency errors in the sunxi-ng
code a couple times now. Each time the fix is to find the missing
select statement and add it to the Kconfig entry for a particular
SoC driver. Given that all this code is builtin (non-modular) we
don't need to do this complicated dependency tracking in Kconfig.
Instead we can move all the "library"ish code to be compiled as
lib-y instead of obj-y, let the linker throw away unused code in
the resulting vmlinux, and drop all the Kconfig stuff we use to
track clock types.
Suggested-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
[Maxime: added lib.a to obj-y, added the comment]
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The A83T's PRCM has the same set of clocks and resets as the A64.
However, a few dividers are different. And due to the lack of a low
speed 32.768 kHz oscillator, a few of the clock parents are different.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The A83T's PRCM has the same set of clocks and resets as the A64.
However, a few dividers are different. And due to the lack of a low
speed 32.768 kHz oscillator, a few of the clock parents are different.
The PRCM also has controls for various power domains. These are not
supported yet.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
We get a link error when CCU_MULT is not set with the
newly added driver:
drivers/clk/sunxi-ng/ccu-sun8i-a83t.o:(.data.__compound_literal.1+0x4): undefined reference to `ccu_mult_ops'
drivers/clk/sunxi-ng/ccu-sun8i-a83t.o:(.data.__compound_literal.3+0x4): undefined reference to `ccu_mult_ops'
Fixes: 46b492116666 ("clk: sunxi-ng: Add driver for A83T CCU")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
The divider of the audio PLL has an offset of 1.
Fix this in the driver.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The offset for the PLL lock status register was incorrectly set to
0x208, which actually points to an unused register. The correct
register offset is 0x20c.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The A83T clock control unit is a hybrid of some new style clock designs
from the A80, and old style layout from the other Allwinner SoCs.
Like the A80, the SoC does not have a low speed 32.768 kHz oscillator.
Unlike the A80, there is no clock input either. The only low speed clock
available is the internal oscillator which runs at around 16 MHz,
divided by 512, yielding a low speed clock around 31.250 kHz.
Also, the MMC2 module clock supports switching to a "new timing" mode.
This mode divides the clock output by half, and disables the CCU based
clock delays. The MMC controller must be configure to the same mode,
and then use its internal clock delays.
This driver does not support runtime switching of the timing modes.
Instead, the new timing mode is enforced at probe time. Consumers can
check which mode is active by trying to get the current phase delay
of the MMC2 phase clocks, which will return -ENOTSUPP if the new
timing mode is active.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
On the A83T, the AHB1 clock has a shared pre-divider on the two
PLL-PERIPH clock parents. To support such instances of shared
pre-dividers, this patch extends the mux clock type to support
multiple variable pre-dividers.
As the pre-dividers are only used to calculate the rate, but
do not participate in the factorization process, this is fairly
straightforward.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The A83T clock control unit is a hybrid of some new style clock designs
from the A80, and old style layout from the other Allwinner SoCs.
Like the A80, the SoC does not have a low speed 32.768 kHz oscillator.
Unlike the A80, there is no clock input either. The only low speed clock
available is the internal oscillator which runs at around 16 MHz,
divided by 512, yielding a low speed clock around 31.250 kHz.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
PTR_ERR should access the value just tested by IS_ERR, otherwise
the wrong error code will be returned.
Fixes: b0d9a4bd52bd ("clk: sunxi-ng: add support for DE2 CCU")
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The video PLLs are used directly by the HDMI controller. Export them so
that we can use them in our DT node.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Currently, the parent rate given back to the clock framework in our
request is the original parent rate we calculated before trying to round
the rate of our clock.
This works fine unless our clock also changes its parent rate, in which
case we will simply ignore that change and still use the previous parent
rate.
Create a new function to re-adjust the parent rate to take the pre-dividers
into account, and give that back to the clock framework.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
The current function name is a bit confusing, and doesn't really allow to
create an explicit function to reverse the operation.
We also for now change the parent rate through a pointer, while we don't
return anything.
In order to be less confusing, and easier to use for downstream users,
change the function name to something hopefully clearer, and return the
adjusted rate instead of changing the pointer.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
The pre-divider retrieval code was merged into the function to apply the
current pre-divider onto the parent clock rate so that we can use that
adjusted value to do our factors computation.
However, since we'll need to do the reverse operation, we need to split out
that code into a function that will be shared.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
The current code only rely on the parent to change its rate in the case
where CLK_SET_RATE_PARENT is set.
However, some clock rates might be obtained only through a modification of
the parent and the clock divider. Just rely on the round rate of the clocks
to give us the best computation that might be achieved for a given rate.
round_rate functions now need to honor CLK_SET_RATE_PARENT, but either the
functions already do that if they modify the parent, or don't modify the
praents at all.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
divider_round_rate_parent already evaluates changing the parent rate if
CLK_SET_RATE_PARENT is set. Now that we can do that on muxes too, let's
just use it.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
The clocks might need to modify their parent clocks. In order to make that
possible, give them access to the parent clock being evaluated, and to a
pointer to the parent rate so that they can modify it if needed.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
So far, divider_round_rate only considers the parent clock returned by
clk_hw_get_parent.
This works fine on clocks that have a single parents, this doesn't work on
muxes, since we will only consider the first parent, while other parents
may totally be able to provide a better combination.
Clocks in that case cannot use divider_round_rate, so would have to come up
with a very similar logic to work around it. Instead of having to do
something like this, and duplicate that logic everywhere, create a
divider_round_rate parent to allow caller to give an additional parameter
for the parent clock to consider.
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
ccu_reset.h and ccu_reset.c use spinlock_t and associated functions but
rely on implict inclusion of linux/spinlock.h which means that changes
in other headers could break the build. Thus, add an explicit include.
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The "Display Engine 2.0" in Allwinner newer SoCs contains a clock
management unit for its subunits, like the DE CCU in A80.
Add a sunxi-ng style driver for it.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>