The Allwinner A31/A31s SoCs have 2 display pipelines, as in 2 display
frontends, backends, and tcons each. The relationship between the
backends and tcons are 1:1, but the frontends can feed either backend.
Add device nodes and of graph nodes describing this relationship.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The NextThing Co. CHIP has an AXP209 PMIC with battery connector.
This enables the battery power supply subnode.
Signed-off-by: Quentin Schulz <quentin.schulz@free-electrons.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The Sinlinx SinA33 has an AXP223 PMIC and a battery connector, thus, we
enable the battery power supply subnode in its Device Tree.
Signed-off-by: Quentin Schulz <quentin.schulz@free-electrons.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The X-Powers AXP22X PMIC exposes battery supply various data such as
the battery status (charging, discharging, full, dead), current max
limit, current current, battery capacity (in percentage), voltage max
limit, current voltage, and battery capacity (in Ah).
This adds the battery power supply subnode for AXP22X PMIC.
Signed-off-by: Quentin Schulz <quentin.schulz@free-electrons.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The X-Powers AXP209 PMIC exposes battery supply various data such as
the battery status (charging, discharging, full, dead), current max
limit, current current, battery capacity (in percentage), voltage max
and min limits, current voltage, and battery capacity (in Ah).
This adds the battery power supply subnode for AXP20X PMIC.
Signed-off-by: Quentin Schulz <quentin.schulz@free-electrons.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Compiling the DT file with W=1, DTC warns like follows:
Warning (unit_address_vs_reg): Node /opp_table0/opp@1000000000 has a
unit name, but no reg property
Fix this by replacing '@' with '-' as the OPP nodes will never have a
"reg" property.
Reported-by: Krzysztof Kozlowski <krzk@kernel.org>
Reported-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Suggested-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The Bananapi M2 Plus has a USB OTG port that can be used in both
powered host mode and peripheral mode. When in peripheral mode,
the port does not power the board. There is no VBUS sensing on
the port.
This patch adds the regulator controlling VBUS on the OTG port,
the GPIO for the ID detect pin, and enables the USB OTG and host
controllers.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The Orange Pi PC, PC Plus, and Plus 2E all have a USB OTG port
that can be used in both powered host mode and peripheral mode.
When in peripheral mode, the port does not power the board.
There is no VBUS sensing on the port. All three boards have all
related pins routed the same way.
The device tree file for the Orange Pi Plus 2E is based on the
Orange Pi PC Plus, which itself is based on the Orange Pi PC.
Changes to the base Orange Pi PC device tree file affects all 3
boards.
This patch adds the regulator controlling VBUS on the OTG port,
the GPIO for the ID detect pin, and enables the USB OTG and host
controllers.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
As part of our effort to move pinctrl/GPIO interlocking into the
driver where it belongs, this patch drops the definition and usage
of the mmc0_cd_pin_reference_design pinmux setting for the default
mmc0 card detect GPIO pin.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
As part of our effort to move pinctrl/GPIO interlocking into the
driver where it belongs, this patch drops the definition and usage
of the pinmux settings for the common regulators defined in
sunxi-common-regulators.dtsi.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The pinmux setting nodes all have an address element in their node
names, however the pinctrl node does not have #address-cells.
Rename the existing pinmux setting nodes and labels in sun8i-a83t.dtsi,
dropping identifiers for functions that only have one possible setting,
and using the pingroup name if the function is identically available on
different pingroups.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
skeleton.dtsi is deprecated. Remove it from sun8i-a83t.dtsi and add
the needed device nodes directly.
Also drop an extra, non-style-conforming line in the copyright license
header.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
sun4i_backend_layer_enable can be called to enable or disable a layer.
However the debug message always says "Enable", which is confusing.
This patch makes the debug message vary according to the enable state.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Currently we are configuring the TCON's dot clock or special clock
directly from the encoder mode_set functions. Since we already
provide mode_set helper functions for the TCON's 2 channels, we
can set the respective clock from those helpers, and reduce the
exposure of the TCON's internals.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The tcons and backends have a one-to-one relationship. Their IDs,
or indexes in the documentation, are also the same.
Copy the ID from the associated backend and save it in the tcon
structure. This will later be used when we add support for the
output data path muxes.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
With Allwinner's Display Engine 1.0, each TCON's input is tied to a
specific display backend, and the 2 comprise what is known as a crtc
in DRM KMS land: The layer, framebuffer, and compositing functions are
provided by the backend, while the TCON provides the display timing
signals and vblank interrupts. This 1 to 1 relationship is represented
in the device tree. On some systems there is an intermediate DRC
component.
Pointers to both matching components must be provided when initializing
the crtc. As the backend is always registered before the associated
tcon, we can recursively search upwards through the of_graph to find
the matching backend.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Save a pointer to the backend's underlying device tree node in its
data structure. This will be used later for downstream tcons to find
and match their respective upstream backends.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Some Allwinner SoCs have 2 display pipelines, as in 2 of each
components, including the frontend, backend, TCON, and any other
extras.
As the backend and TCON are always paired together and form the CRTC,
we need to know which backend or TCON we are currently probing, so we
can pair them when initializing the CRTC.
This patch figures out the backend's ID from the device tree and stores
it in the backend's data structure. It does this by looking at the "reg"
property of any remote endpoints connected to the backend's input port.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Now that we support multiple instances of backends, the trailing 0
implying only one backend no longer makes sense.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
To support multiple display pipelines, we need to keep track of the
multiple display backends and TCONs registered with the driver.
Switch to lists to track registered components. Components are only
appended to their respective lists if the bind process was successful.
The TCON bind function now defers if a backend was not registered.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The Allwinner display pipeline contains many hardware components, some
of which can consume data from one of multiple upstream components.
The numbering scheme of these components must be encoded into the device
tree so the driver can figure out which component out of two or more of
the same type it is supposed to use or program.
This patch adds the constraint that local endpoint IDs must be the index
or number of the remote endpoint's hardware block, for all components
in the display pipeline up to the TCONs.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
V3S's usb otg device reset bit should be 24, not 23.
Cc: stable@vger.kernel.org
Signed-off-by: Yong Deng <iemdey@gmail.com>
Reviewed-By: Icenowy Zheng <icenowy@aosc.io>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The register offset for the lcd1-ch1 clock was incorrectly pointing to
the lcd0-ch1 clock. This resulted in the lcd0-ch1 clock being disabled
when the clk core disables unused clocks. This then stops the simplefb
HDMI output path.
Reported-by: Bob Ham <rah@settrans.net>
Fixes: c6e6c96d8f ("clk: sunxi-ng: Add A31/A31s clocks")
Cc: stable@vger.kernel.org # 4.9.x-
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Remove the duplicate brcm,bcm7425-sun-top-ctrl compatible string and
replace it with brcm,bcm7435-sun-top-ctrl which was intended.
Fixes: bd0faf08dc ("soc: bcm: brcmstb: Match additional compatible strings")
Reported-by: Andreas Oberritter <obi@saftware.de>
Acked-by: Gregory Fong <gregory.0xf0@gmail.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
This pull request brings back bcm2835 DT fixups from Baruch Siach that
got misplaced after a PR for 4.11 got rejected.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
The 7278 introduces a new version of this core. This
commit adds support for that revision.
Signed-off-by: Doug Berger <opendmb@gmail.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
The ARM64 architecture can provide meaningful diagnostic
output from the GISB arbiter solely from interrupts and
notifiers without the need to hook the low level fault
handlers.
Signed-off-by: Doug Berger <opendmb@gmail.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
The ARM architecture can provide meaningful diagnostic
output from the GISB arbiter solely from interrupts and
notifiers without the need to hook the low level fault
handlers.
Signed-off-by: Doug Berger <opendmb@gmail.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Check for GISB arbitration errors through a chained notifier
when a process dies or a kernel panic occurs. This allows a
meaningful GISB diagnostic message to occur along with other
diagnostic information from the event.
Signed-off-by: Doug Berger <opendmb@gmail.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
The GISB bus can support addresses beyond 32-bits. So this commit
corrects support for reading a captured 64-bit address into a 64-bit
variable by obtaining the high bits from the ARB_ERR_CAP_HI_ADDR
register (when present) and then outputting the full 64-bit value.
It also removes unused definitions.
Fixes: 44127b771d ("bus: add Broadcom GISB bus arbiter timeout/error handler")
Signed-off-by: Doug Berger <opendmb@gmail.com>
Acked-by: Gregory Fong <gregory.0xf0@gmail.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
This commit corrects the bug introduced in commit f80835875d
("bus: brcmstb_gisb: Look up register offsets in a table") such
that gisb_write() translates the register enumeration into an
offset from the base address for writes as well as reads.
Fixes: f80835875d ("bus: brcmstb_gisb: Look up register offsets in a table")
Signed-off-by: Doug Berger <opendmb@gmail.com>
Acked-by: Gregory Fong <gregory.0xf0@gmail.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Adjust the PHY parameters for more stable access to the eMMC device.
Set the SDCLK output delay value to 21 (including HS200/400 modes).
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Since commit a89c472d8b ("mmc: sdhci-cadence: Update PHY delay
configuration"), PHY parameters must be specified by DT.
The hard-coded settings have been converted as follows:
- SDHCI_CDNS_PHY_DLY_SD_DEFAULT -> cdns,phy-input-delay-legacy
- SDHCI_CDNS_PHY_DLY_EMMC_SDR -> cdns,phy-input-delay-mmc-highspeed
- SDHCI_CDNS_PHY_DLY_EMMC_DDR -> cdns,phy-input-delay-mmc-ddr
The following have not been moved:
- SDHCI_CDNS_PHY_DLY_SD_HS
this is unneeded in the eMMC configuration
- SDHCI_CDNS_PHY_DLY_EMMC_LEGACY
this is never enabled by the driver as it is covered by
SDHCI_CDNS_PHY_DLY_SD_DEFAULT
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
The default NetBSD package manager is pkgsrc and it installs Perl
along other third party programs under custom and configurable prefix.
The default prefix for binary prebuilt packages is /usr/pkg, and the
Perl executable lands in /usr/pkg/bin/perl.
This change switches "/usr/bin/perl" to "/usr/bin/env perl" as it's
the most portable solution that should work for almost everybody.
Perl's executable is detected automatically.
This change switches -w option passed to the executable with more
modern "use warnings;" approach. There is no functional change to the
default behavior.
While there, drop "require 5" from scripts/namespace.pl (Perl from 1994?).
Signed-off-by: Kamil Rytarowski <n54@gmx.com>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Tetsuo reports:
fs/built-in.o: In function `xfs_file_iomap_end':
xfs_iomap.c:(.text+0xe0ef9): undefined reference to `put_dax'
fs/built-in.o: In function `xfs_file_iomap_begin':
xfs_iomap.c:(.text+0xe1a7f): undefined reference to `dax_get_by_host'
make: *** [vmlinux] Error 1
$ grep DAX .config
CONFIG_DAX=m
# CONFIG_DEV_DAX is not set
# CONFIG_FS_DAX is not set
When FS_DAX=n we can/must throw away the dax code in filesystems.
Implement 'fs_' versions of dax_get_by_host() and put_dax() that are
nops in the FS_DAX=n case.
Cc: <linux-xfs@vger.kernel.org>
Cc: <linux-ext4@vger.kernel.org>
Cc: Jan Kara <jack@suse.com>
Cc: "Theodore Ts'o" <tytso@mit.edu>
Cc: "Darrick J. Wong" <darrick.wong@oracle.com>
Cc: Ross Zwisler <ross.zwisler@linux.intel.com>
Tested-by: Tony Luck <tony.luck@intel.com>
Fixes: ef51042472 ("block, dax: move 'select DAX' from BLOCK to FS_DAX")
Reported-by: Tetsuo Handa <penguin-kernel@i-love.sakura.ne.jp>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Commit eed4d47efe (ACPI / sleep: Ignore spurious SCI wakeups from
suspend-to-idle) modified the core suspend-to-idle code to filter
out spurious SCI interrupts received while suspended, which requires
ACPI event source handlers to report wakeup events in a way that
will trigger a wakeup from suspend to idle (or abort system suspends
in progress, which is equivalent).
That needs to be done in the rtc-cmos driver too, which was overlooked
by the above commit, so do that now.
Fixes: eed4d47efe (ACPI / sleep: Ignore spurious SCI wakeups from suspend-to-idle)
Reported-by: David E. Box <david.e.box@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Commit 8a537ece3d (PM / wakeup: Integrate mechanism to abort
transitions in progress) modified wakeup_source_report_event()
and wakeup_source_activate() to make it possible to call
pm_system_wakeup() from the latter if so indicated by the
caller of the former (via a new function argument added by that
commit), but it overlooked the fact that in some situations
wakeup_source_report_event() is called to signal a "hard" event
(ie. such that should abort a system suspend in progress) after
pm_stay_awake() has been called for the same wakeup source object,
in which case the pm_system_wakeup() will not trigger.
To work around this issue, modify wakeup_source_activate() and
wakeup_source_report_event() again so that pm_system_wakeup() is
called by the latter directly (if its last argument is true), in
which case the additional argument does not need to be passed
to wakeup_source_activate() any more, so drop it from there.
Fixes: 8a537ece3d (PM / wakeup: Integrate mechanism to abort transitions in progress)
Reported-by: David E. Box <david.e.box@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Add a document describing the current behavior and user space
interface of the intel_pstate driver in the RST format and
drop the existing outdated intel_pstate.txt document.
Also update admin-guide/pm/cpufreq.rst with proper RST references
to the new intel_pstate.rst document.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
In the BLOCK=n case the dax core does not need to / must not emit the
block-device-dax helpers. Otherwise it leads to compile errors.
Cc: Arnd Bergmann <arnd@arndb.de>
Reported-by: Fabian Frederick <fabf@skynet.be>
Fixes: ef51042472 ("block, dax: move 'select DAX' from BLOCK to FS_DAX")
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Add a rockchip,rv1108 compatible.
Signed-off-by: Andy Yan <andy.yan@rock-chips.com>
[rk1108->rv1108 rename]
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
RK1108 UARTs are Synopsis DesignWare 8250 compatible.
Only with different register addresses.
Signed-off-by: Andy Yan <andy.yan@rock-chips.com>
Tested-by: Jacob Chen <jacob2.chen@rock-chips.com>
[rk1108->rv1108 rename]
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Firefly-rk3399 is a bord from T-Firefly, you can find detail about
it here:
http://en.t-firefly.com/en/firenow/Firefly_RK3399/
This patch add basic node for the board and make it able to bring
up.
Peripheral works:
- usb hub which connect to ehci controller;
- UART2 debug
- eMMC
- PCIe
Not work:
- USB 3.0 HOST, type-C port
- sdio, sd-card
Not test for other peripheral:
- HDMI
- Ethernet
- OPTICAL
- WiFi/BT
- MIPI CSI/DSI
- IR
- EDP/DP
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Use "firefly,firefly-rk3399" compatible string for firefly-rk3399 board.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Now that the rockchip usb phy has a vbus-supply property use that to
control the vbus regulator on rock2.
Signed-off-by: Sjoerd Simons <sjoerd.simons@collabora.co.uk>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Imagine we have a pid namespace and a task from its parent's pid_ns,
which made setns() to the pid namespace. The task is doing fork(),
while the pid namespace's child reaper is dying. We have the race
between them:
Task from parent pid_ns Child reaper
copy_process() ..
alloc_pid() ..
.. zap_pid_ns_processes()
.. disable_pid_allocation()
.. read_lock(&tasklist_lock)
.. iterate over pids in pid_ns
.. kill tasks linked to pids
.. read_unlock(&tasklist_lock)
write_lock_irq(&tasklist_lock); ..
attach_pid(p, PIDTYPE_PID); ..
.. ..
So, just created task p won't receive SIGKILL signal,
and the pid namespace will be in contradictory state.
Only manual kill will help there, but does the userspace
care about this? I suppose, the most users just inject
a task into a pid namespace and wait a SIGCHLD from it.
The patch fixes the problem. It simply checks for
(pid_ns->nr_hashed & PIDNS_HASH_ADDING) in copy_process().
We do it under the tasklist_lock, and can't skip
PIDNS_HASH_ADDING as noted by Oleg:
"zap_pid_ns_processes() does disable_pid_allocation()
and then takes tasklist_lock to kill the whole namespace.
Given that copy_process() checks PIDNS_HASH_ADDING
under write_lock(tasklist) they can't race;
if copy_process() takes this lock first, the new child will
be killed, otherwise copy_process() can't miss
the change in ->nr_hashed."
If allocation is disabled, we just return -ENOMEM
like it's made for such cases in alloc_pid().
v2: Do not move disable_pid_allocation(), do not
introduce a new variable in copy_process() and simplify
the patch as suggested by Oleg Nesterov.
Account the problem with double irq enabling
found by Eric W. Biederman.
Fixes: c876ad7682 ("pidns: Stop pid allocation when init dies")
Signed-off-by: Kirill Tkhai <ktkhai@virtuozzo.com>
CC: Andrew Morton <akpm@linux-foundation.org>
CC: Ingo Molnar <mingo@kernel.org>
CC: Peter Zijlstra <peterz@infradead.org>
CC: Oleg Nesterov <oleg@redhat.com>
CC: Mike Rapoport <rppt@linux.vnet.ibm.com>
CC: Michal Hocko <mhocko@suse.com>
CC: Andy Lutomirski <luto@kernel.org>
CC: "Eric W. Biederman" <ebiederm@xmission.com>
CC: Andrei Vagin <avagin@openvz.org>
CC: Cyrill Gorcunov <gorcunov@openvz.org>
CC: Serge Hallyn <serge@hallyn.com>
Cc: stable@vger.kernel.org
Acked-by: Oleg Nesterov <oleg@redhat.com>
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
The code can potentially sleep for an indefinite amount of time in
zap_pid_ns_processes triggering the hung task timeout, and increasing
the system average. This is undesirable. Sleep with a task state of
TASK_INTERRUPTIBLE instead of TASK_UNINTERRUPTIBLE to remove these
undesirable side effects.
Apparently under heavy load this has been allowing Chrome to trigger
the hung time task timeout error and cause ChromeOS to reboot.
Reported-by: Vovo Yang <vovoy@google.com>
Reported-by: Guenter Roeck <linux@roeck-us.net>
Tested-by: Guenter Roeck <linux@roeck-us.net>
Fixes: 6347e90091 ("pidns: guarantee that the pidns init will be the last pidns process reaped")
Cc: stable@vger.kernel.org
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Pull some more input subsystem updates from Dmitry Torokhov:
"An updated xpad driver with a few more recognized device IDs, and a
new psxpad-spi driver, allowing connecting Playstation 1 and 2 joypads
via SPI bus"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: cros_ec_keyb - remove extraneous 'const'
Input: add support for PlayStation 1/2 joypads connected via SPI
Input: xpad - add USB IDs for Mad Catz Brawlstick and Razer Sabertooth
Input: xpad - sync supported devices with xboxdrv
Input: xpad - sort supported devices by USB ID