The "jiggle" code was not actually expecting failure, which it should
because that's what actually happens when the device wasn't already woken
up by the regulator power-on (i.e. in the case of a shared regulator).
Also, do actually enter the internal suspend mode on shutdown, to save
power in the case of a shared regulator.
Also, wait a bit longer (2x tOPR) on waking up, 1x is not enough at least
on the DW9718S as found on the motorola-nora smartphone.
Signed-off-by: Val Packett <val@packett.cool>
Signed-off-by: André Apitzsch <git@apitzsch.eu>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil+cisco@kernel.org>
Update the close callback to match other similar drivers like dw9768.
Signed-off-by: Val Packett <val@packett.cool>
Signed-off-by: André Apitzsch <git@apitzsch.eu>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil+cisco@kernel.org>
The DW9718S is a similar part that uses a different register set but
follows the same method of operation otherwise. Add support for it
to the existing dw9719 driver.
Tested on the Moto E5 (motorola-nora) smartphone.
Signed-off-by: Val Packett <val@packett.cool>
Signed-off-by: André Apitzsch <git@apitzsch.eu>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil+cisco@kernel.org>
In preparation for adding models with different register sets, start
assigning the model based on the i2c match data.
Signed-off-by: Val Packett <val@packett.cool>
Signed-off-by: André Apitzsch <git@apitzsch.eu>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil+cisco@kernel.org>
Allow the dw9719 driver to be attached via FDT.
Signed-off-by: Val Packett <val@packett.cool>
Signed-off-by: André Apitzsch <git@apitzsch.eu>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil+cisco@kernel.org>
Nothing depends on the I²C device ID table, so remove it.
Signed-off-by: André Apitzsch <git@apitzsch.eu>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil+cisco@kernel.org>
The name of property "dongwoon,vcm-freq" doesn't match its purpose.
Change the name of the property to "dongwoon,vcm-prescale" to better
describe its purpose and deprecate the old one.
Signed-off-by: André Apitzsch <git@apitzsch.eu>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil+cisco@kernel.org>
Put the reference to csi_dev acquired during driver probe in
mei_ace_setup_dev_link() inside the same function, instead of during driver
unbind in mei_ace_remove(). This can be done as device_link_add() already
takes a reference to csi_dev.
Signed-off-by: Ma Ke <make24@iscas.ac.cn>
[Sakari Ailus: Rework commit message.]
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil+cisco@kernel.org>
Wentong's e-mail no longer works; assign the ov08x40 driver to Jimmy Su.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil+cisco@kernel.org>
The new program for removing unused tracepoints is not ignored as it
should. Add it to the local .gitignore.
Cc: Vladimir Oltean <vladimir.oltean@nxp.com>
Cc: Jacob Keller <jacob.e.keller@intel.com>
Cc: Jakub Kicinski <kuba@kernel.org>
Link: https://lore.kernel.org/20251029120709.24669-1-brgl@bgdev.pl
Fixes: e30f8e61e2 ("tracing: Add a tracepoint verification check at build time")
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Signed-off-by: Steven Rostedt (Google) <rostedt@goodmis.org>
Rework of imported buffers introduced in the commit
e0c0891cd6 ("accel/ivpu: Rework bind/unbind of imported buffers")
switched the logic of imported buffers by dma mapping/unmapping
them just as the regular buffers.
The commit didn't include removal of skipping dma unmap of imported
buffers which results in them being mapped without unmapping.
Fixes: e0c0891cd6 ("accel/ivpu: Rework bind/unbind of imported buffers")
Reviewed-by: Jeff Hugo <jeff.hugo@oss.qualcomm.com>
Reviewed-by: Karol Wachowski <karol.wachowski@linux.intel.com>
Signed-off-by: Maciej Falkowski <maciej.falkowski@linux.intel.com>
Link: https://patch.msgid.link/20251027150933.2384538-1-maciej.falkowski@linux.intel.com
When em_create_perf_table() returns failure, pd is freed, there dev->em_pd
is not valid. Then accessing dev->em_pd->node will trigger kernel panic
in em_dev_register_pd_no_update(). So return early if 'ret' is non-zero.
Kernel dump:
cpu cpu0: EM: invalid power: 0
Unable to handle kernel NULL pointer dereference at virtual address
0000000000000008
Mem abort info:
pc : em_dev_register_pd_no_update+0xb4/0x79c
lr : em_dev_register_pd_no_update+0x9c/0x79c
Call trace:
em_dev_register_pd_no_update+0xb4/0x79c (P)
em_dev_register_perf_domain+0x18/0x58
scmi_cpufreq_register_em+0x84/0xb8
cpufreq_online+0x48c/0xb74
cpufreq_add_dev+0x80/0x98
subsys_interface_register+0x100/0x11c
cpufreq_register_driver+0x158/0x278
scmi_cpufreq_probe+0x1f8/0x2e0
scmi_dev_probe+0x28/0x3c
really_probe+0xbc/0x29c
__driver_probe_device+0x78/0x12c
driver_probe_device+0x3c/0x15c
__device_attach_driver+0xb8/0x134
bus_for_each_drv+0x84/0xe4
Fixes: cbe5aeedec ("PM: EM: Assign a unique ID when creating a performance domain")
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Changwoo Min <changwoo@igalia.com>
Reviewed-by: Lukasz Luba <lukasz.luba@arm.com>
Link: https://patch.msgid.link/20251028-fix-energy-v1-1-ab854fd6a97c@nxp.com
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
When triggering a stack dump via sysrq (echo t > /proc/sysrq-trigger),
KASAN may report false-positive out-of-bounds access:
BUG: KASAN: out-of-bounds in __show_regs+0x4b/0x340
Call Trace:
dump_stack_lvl
print_address_description.constprop.0
print_report
__show_regs
show_trace_log_lvl
sched_show_task
show_state_filter
sysrq_handle_showstate
__handle_sysrq
write_sysrq_trigger
proc_reg_write
vfs_write
ksys_write
do_syscall_64
entry_SYSCALL_64_after_hwframe
The issue occurs as follows:
Task A (walk other tasks' stacks) Task B (running)
1. echo t > /proc/sysrq-trigger
show_trace_log_lvl
regs = unwind_get_entry_regs()
show_regs_if_on_stack(regs)
2. The stack value pointed by
`regs` keeps changing, and
so are the tags in its
KASAN shadow region.
__show_regs(regs)
regs->ax, regs->bx, ...
3. hit KASAN redzones, OOB
When task A walks task B's stack without suspending it, the continuous changes
in task B's stack (and corresponding KASAN shadow tags) may cause task A to
hit KASAN redzones when accessing obsolete values on the stack, resulting in
false positive reports.
Simply stopping the task before unwinding is not a viable fix, as it would
alter the state intended to inspect. This is especially true for diagnosing
misbehaving tasks (e.g., in a hard lockup), where stopping might fail or hide
the root cause by changing the call stack.
Therefore, fix this by disabling KASAN checks during asynchronous stack
unwinding, which is identified when the unwinding task does not match the
current task (task != current).
[ bp: Align arguments on function's opening brace. ]
Fixes: 3b3fa11bc7 ("x86/dumpstack: Print any pt_regs found on the stack")
Signed-off-by: Tengda Wu <wutengda@huaweicloud.com>
Signed-off-by: Borislav Petkov (AMD) <bp@alien8.de>
Reviewed-by: Andrey Ryabinin <ryabinin.a.a@gmail.com>
Acked-by: Josh Poimboeuf <jpoimboe@kernel.org>
Link: https://patch.msgid.link/all/20251023090632.269121-1-wutengda@huaweicloud.com
Add the compatible for an 64Kb EEPROM from Belling.
Signed-off-by: Luca Weiss <luca@lucaweiss.eu>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20251028-msm8953-cci-v2-3-b5f9f7135326@lucaweiss.eu
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
WildcatLake (WCL) is a variant of PantherLake (PTL) and shares the same
uncore PMU features with PTL. Therefore, directly reuse Pantherlake's
uncore PMU enabling code for WildcatLake.
Signed-off-by: dongsheng <dongsheng.x.zhang@intel.com>
Signed-off-by: Dapeng Mi <dapeng1.mi@linux.intel.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Link: https://patch.msgid.link/20250908061639.938105-2-dapeng1.mi@linux.intel.com
WildcatLake is a variant of PantherLake and shares same PMU features,
so directly reuse Pantherlake's code to enable PMU features for
WildcatLake.
Signed-off-by: Dapeng Mi <dapeng1.mi@linux.intel.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Reviewed-by: Zide Chen <zide.chen@intel.com>
Link: https://patch.msgid.link/20250908061639.938105-1-dapeng1.mi@linux.intel.com
the DEFINE_CLASS() macro creates an inline function and
the init args are passed down to it; since _ret is passed as an int,
whatever value is set inside the function is not visible to the caller.
Pass _ret as a pointer so its value propagates to the caller.
Fixes: c460bc2311 ("drm/xe: Introduce an xe_validation wrapper around drm_exec")
Closes: https://gitlab.freedesktop.org/drm/xe/kernel/-/issues/6220
Cc: Maarten Lankhorst <maarten.lankhorst@intel.com>
Cc: Matthew Brost <matthew.brost@intel.com>
Cc: intel-xe@lists.freedesktop.org
Signed-off-by: Thomas Hellström <thomas.hellstrom@linux.intel.com>
Reviewed-by: Lucas De Marchi <lucas.demarchi@intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Matthew Brost <matthew.brost@intel.com>
Link: https://patch.msgid.link/20251027131228.12098-1-thomas.hellstrom@linux.intel.com
Convert register bitfields to GENMASK() macro where applicable.
Use FIELD_PREP() throughout the driver.
Reviewed-by: Tomi Valkeinen <tomi.valkeinen+renesas@ideasonboard.com>
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Link: https://patch.msgid.link/20251028232959.109936-12-marek.vasut+renesas@mailbox.org
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Convert register bits to BIT() macro where applicable. This is done
automatically using regex 's@(1 << \([0-9]\+\))@BIT(\1)', except for
bitfields which are manually updated to use GENMASK().
Reviewed-by: Tomi Valkeinen <tomi.valkeinen+renesas@ideasonboard.com>
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Link: https://patch.msgid.link/20251028232959.109936-11-marek.vasut+renesas@mailbox.org
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Introduce TXVMVPRMSET0R_BPP_MASK macro and use FIELD_PREP() to generate
appropriate bitfield from mask and value without bitshift, assign this
value into vprmset0r. Remove TXVMVPRMSET0R_CSPC_RGB which is never used,
replace it with code comment next to TXVMVPRMSET0R_CSPC_YCbCr.
Replace (mode->flags & DRM_MODE_FLAG_P.SYNC) test with inverted conditional
(mode->flags & DRM_MODE_FLAG_N.SYNC) and bitwise orr vprmset0r with either
or both TXVMVPRMSET0R_HSPOL_LOW and TXVMVPRMSET0R_VSPOL_LOW if conditional
matches.
Do not convert bits and bitfields to BIT() and GENMASK() yet, to be
consisten with the current style. Conversion to BIT() and GENMASK()
macros is done at the very end of this series in the last two patches.
Reviewed-by: Tomi Valkeinen <tomi.valkeinen+renesas@ideasonboard.com>
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Link: https://patch.msgid.link/20251028232959.109936-10-marek.vasut+renesas@mailbox.org
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Cache DSI mode flags in new mode_flags member of struct rcar_mipi_dsi .
Configure TXVMSETR register based on the content of DSI mode flags in
case the controller operates in video mode.
Rename TXVMSETR_H..BPEN_EN to TXVMSETR_H..BPEN and drop TXVMSETR_H..BPEN_DIS
which resolves to 0. Update TXVMSETR_VSEN in the same manner. Replace
TXVMSETR_SYNSEQ_PULSES with a code comment next to TXVMSETR_SYNSEQ_EVENTS
because TXVMSETR_SYNSEQ_PULSES resolves to 0.
Do not convert bits and bitfields to BIT() and GENMASK() yet, to be
consisten with the current style. Conversion to BIT() and GENMASK()
macros is done at the very end of this series in the last two patches.
Reviewed-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen+renesas@ideasonboard.com>
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Link: https://patch.msgid.link/20251028232959.109936-9-marek.vasut+renesas@mailbox.org
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Introduce TXVMPSPHSETR_DT_MASK macro and use FIELD_PREP() to generate
appropriate bitfield from mask and value without bitshift.
Do not convert bits and bitfields to BIT() and GENMASK() yet, to be
consisten with the current style. Conversion to BIT() and GENMASK()
macros is done at the very end of this series in the last two patches.
Reviewed-by: Tomi Valkeinen <tomi.valkeinen+renesas@ideasonboard.com>
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Link: https://patch.msgid.link/20251028232959.109936-8-marek.vasut+renesas@mailbox.org
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Introduce CLOCKSET1_CLKINSEL_MASK macro and remove bitshift from
values to make this bitfield usable with FIELD_PREP(). There are
no users of this bitfield, hence no updates to the DSI driver.
Do not convert bits and bitfields to BIT() and GENMASK() yet, to be
consisten with the current style. Conversion to BIT() and GENMASK()
macros is done at the very end of this series in the last two patches.
Reviewed-by: Tomi Valkeinen <tomi.valkeinen+renesas@ideasonboard.com>
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Link: https://patch.msgid.link/20251028232959.109936-7-marek.vasut+renesas@mailbox.org
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Introduce VCLKSET_BPP_MASK macro and use FIELD_PREP() to generate
appropriate bitfield from mask and value without bitshift. Remove
VCLKSET_COLOR_RGB which is never used, replace it with code comment.
Do not convert bits and bitfields to BIT() and GENMASK() yet, to be
consisten with the current style. Conversion to BIT() and GENMASK()
macros is done at the very end of this series in the last two patches.
Reviewed-by: Tomi Valkeinen <tomi.valkeinen+renesas@ideasonboard.com>
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Link: https://patch.msgid.link/20251028232959.109936-6-marek.vasut+renesas@mailbox.org
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Call mipi_dsi_pixel_format_to_bpp() once in rcar_mipi_dsi_set_display_timing()
and store the value into a variable. This slightly simplifies the code.
No functional change.
Reviewed-by: Tomi Valkeinen <tomi.valkeinen+renesas@ideasonboard.com>
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Link: https://patch.msgid.link/20251028232959.109936-5-marek.vasut+renesas@mailbox.org
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
The register PHTR bitfield TESTDOUT is not a single bit, but a
bitfield. Add a MASK macro and a _TEST bitfield value, which is
used by the driver to poll for completion. No functional change.
Reviewed-by: Tomi Valkeinen <tomi.valkeinen+renesas@ideasonboard.com>
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Link: https://patch.msgid.link/20251028232959.109936-4-marek.vasut+renesas@mailbox.org
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
The register TXVMSETR bitfield PIXWDTH is not a single bit, but a
bitfield. Add a MASK macro and document that the only allowed value
that can ever be written into the bitfield is the current value, 1.
No functional change.
Reviewed-by: Tomi Valkeinen <tomi.valkeinen+renesas@ideasonboard.com>
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Link: https://patch.msgid.link/20251028232959.109936-3-marek.vasut+renesas@mailbox.org
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
The RXSETR_CRCEN(n) and RXSETR_ECCEN(n) macros both take parameter (n),
add the missing macro parameter. Neither of those macros is used by the
driver, so for now the bug is harmless.
Fixes: 685e8dae19 ("drm/rcar-du: dsi: Implement DSI command support")
Reviewed-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen+renesas@ideasonboard.com>
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Reported-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Link: https://patch.msgid.link/20251028232959.109936-2-marek.vasut+renesas@mailbox.org
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Add support for deferred userspace unwind to perf.
Where perf currently relies on in-place stack unwinding; from NMI
context and all that. This moves the userspace part of the unwind to
right before the return-to-userspace.
This has two distinct benefits, the biggest is that it moves the
unwind to a faultable context. It becomes possible to fault in debug
info (.eh_frame, SFrame etc.) that might not otherwise be readily
available. And secondly, it de-duplicates the user callchain where
multiple samples happen during the same kernel entry.
To facilitate this the perf interface is extended with a new record
type:
PERF_RECORD_CALLCHAIN_DEFERRED
and two new attribute flags:
perf_event_attr::defer_callchain - to request the user unwind be deferred
perf_event_attr::defer_output - to request PERF_RECORD_CALLCHAIN_DEFERRED records
The existing PERF_RECORD_SAMPLE callchain section gets a new
context type:
PERF_CONTEXT_USER_DEFERRED
After which will come a single entry, denoting the 'cookie' of the
deferred callchain that should be attached here, matching the 'cookie'
field of the above mentioned PERF_RECORD_CALLCHAIN_DEFERRED.
The 'defer_callchain' flag is expected on all events with
PERF_SAMPLE_CALLCHAIN. The 'defer_output' flag is expect on the event
responsible for collecting side-band events (like mmap, comm etc.).
Setting 'defer_output' on multiple events will get you duplicated
PERF_RECORD_CALLCHAIN_DEFERRED records.
Based on earlier patches by Josh and Steven.
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Link: https://patch.msgid.link/20251023150002.GR4067720@noisy.programming.kicks-ass.net
When userspace is interrupted at the start of a function, before we
get a chance to complete the frame, unwind will miss one caller.
X86 has a uprobe specific fixup for this, add bits to the generic
unwinder to support this.
Suggested-by: Jens Remus <jremus@linux.ibm.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Link: https://patch.msgid.link/20251024145156.GM4068168@noisy.programming.kicks-ass.net
Use ARCH_INIT_USER_FP_FRAME to describe how frame pointers are unwound
on x86, and enable CONFIG_HAVE_UNWIND_USER_FP accordingly so the
unwind_user interfaces can be used.
Signed-off-by: Josh Poimboeuf <jpoimboe@kernel.org>
Signed-off-by: Steven Rostedt (Google) <rostedt@goodmis.org>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Link: https://patch.msgid.link/20250827193828.347397433@kernel.org
The unwind_task_info::unwind_mask was manipulated using a mixture of:
regular store
WRITE_ONCE()
try_cmpxchg()
set_bit()
atomic_long_*()
Clean up and make it consistently atomic_long_t.
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Link: https://patch.msgid.link/20250924080119.384384486@infradead.org
The get_cookie() function hard relies on IRQs being disabled, but this
isn't immediately obvious when reading the function.
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Acked-by: Steven Rostedt (Google) <rostedt@goodmis.org>
Link: https://patch.msgid.link/20250924080119.122507632@infradead.org
task_work_add(RWA_RESUME) isn't NMI-safe, use TWA_NMI_CURRENT when
used from NMI context.
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Reviewed-by: Steven Rostedt (Google) <rostedt@goodmis.org>
Link: https://patch.msgid.link/20250924080119.005422353@infradead.org
Explain why unwind_deferred_task_exit() exist and its constraints.
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Reviewed-by: Steven Rostedt (Google) <rostedt@goodmis.org>
Link: https://patch.msgid.link/20250924080118.893367437@infradead.org
Invert the condition of the first if and make it an early exit to
reduce an indent level for the rest fo the function.
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Reviewed-by: Steven Rostedt (Google) <rostedt@goodmis.org>
Link: https://patch.msgid.link/20250924080118.777916262@infradead.org
To be self sufficient, the file needs to include linux/types.h. This
provides things like u32/u64 and struct callback_head.
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Acked-by: Steven Rostedt (Google) <rostedt@goodmis.org>
Link: https://patch.msgid.link/20250924080118.665787071@infradead.org
There are some exceptionally long lines that cause ugly wrapping.
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Acked-by: Steven Rostedt (Google) <rostedt@goodmis.org>
Link: https://patch.msgid.link/20250924080118.545274393@infradead.org
Clearwater Forest is based on the Darkmont Atom microarchitecture.
>From the perspective of C-state residency profiling, it supports the
same residency counters as Sierra Forest: CC1/CC6, PC2/PC6, and MC6.
Please note that the C1E residency counter can only be read via PMT,
not MSR. Therefore, tools relying on the perf_event framework cannot
access the C1E residency.
Signed-off-by: Zhenyu Wang <zhenyuw.linux@gmail.com>
Signed-off-by: Zide Chen <zide.chen@intel.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Reviewed-by: Kan Liang <kan.liang@linux.intel.com>
Reviewed-by: Dapeng Mi <dapeng1.mi@linux.intel.com>
Link: https://patch.msgid.link/20251023223754.1743928-2-zide.chen@intel.com
When running "perf mem record" command on CWF, the below KASAN
global-out-of-bounds warning is seen.
==================================================================
BUG: KASAN: global-out-of-bounds in cmt_latency_data+0x176/0x1b0
Read of size 4 at addr ffffffffb721d000 by task dtlb/9850
Call Trace:
kasan_report+0xb8/0xf0
cmt_latency_data+0x176/0x1b0
setup_arch_pebs_sample_data+0xf49/0x2560
intel_pmu_drain_arch_pebs+0x577/0xb00
handle_pmi_common+0x6c4/0xc80
The issue is caused by below code in __grt_latency_data(). The code
tries to access x86_hybrid_pmu structure which doesn't exist on
non-hybrid platform like CWF.
WARN_ON_ONCE(hybrid_pmu(event->pmu)->pmu_type == hybrid_big)
So add is_hybrid() check before calling this WARN_ON_ONCE to fix the
global-out-of-bounds access issue.
Fixes: 090262439f ("perf/x86/intel: Rename model-specific pebs_latency_data functions")
Reported-by: Xudong Hao <xudong.hao@intel.com>
Signed-off-by: Dapeng Mi <dapeng1.mi@linux.intel.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Reviewed-by: Zide Chen <zide.chen@intel.com>
Cc: stable@vger.kernel.org
Link: https://patch.msgid.link/20251028064214.1451968-1-dapeng1.mi@linux.intel.com
After conversion of arch code to use physical address mapping,
there are no users of .map_page() and .unmap_page() callbacks,
so let's remove them.
Reviewed-by: Jason Gunthorpe <jgg@nvidia.com>
Signed-off-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Link: https://lore.kernel.org/r/20251015-remove-map-page-v5-14-3bbfe3a25cdf@kernel.org
