Bindig requires a node name matching ‘^ethernet@[0-9a-f]+$’. This patch
changes the clock name from “etop” to “ethernet”.
This fixes the following warning:
arch/mips/boot/dts/lantiq/danube_easy50712.dtb: etop@e180000 (lantiq,etop-xway): $nodename:0: 'etop@e180000' does not match '^ethernet@[0-9a-f]+$'
from schema $id: http://devicetree.org/schemas/net/lantiq,etop-xway.yaml#
Fixes: dac0bad937 ("dt-bindings: net: lantiq,etop-xway: Document Lantiq Xway ETOP bindings")
Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
Acked-by: Jakub Kicinski <kuba@kernel.org>
The upstream dts lacks the lantiq,{rx/tx}-burst-length property. Other
issues were also fixed:
arch/mips/boot/dts/lantiq/danube_easy50712.dtb: etop@e180000 (lantiq,etop-xway): 'interrupt-names' is a required property
from schema $id: http://devicetree.org/schemas/net/lantiq,etop-xway.yaml#
arch/mips/boot/dts/lantiq/danube_easy50712.dtb: etop@e180000 (lantiq,etop-xway): 'lantiq,tx-burst-length' is a required property
from schema $id: http://devicetree.org/schemas/net/lantiq,etop-xway.yaml#
arch/mips/boot/dts/lantiq/danube_easy50712.dtb: etop@e180000 (lantiq,etop-xway): 'lantiq,rx-burst-length' is a required property
from schema $id: http://devicetree.org/schemas/net/lantiq,etop-xway.yaml#
Fixes: 14d4e308e0 ("net: lantiq: configure the burst length in ethernet drivers")
Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
Acked-by: Jakub Kicinski <kuba@kernel.org>
cpufreq drivers are supposed to use either ->setpolicy() or
->target()/->target_index().
Simplify the existing check by collapsing it into a single boolean
expression:
(!!driver->setpolicy == (driver->target_index || driver->target))
This is a readability/maintainability cleanup and keeps the semantics
unchanged.
No functional change intended.
Signed-off-by: Zihuan Zhang <zhangzihuan@kylinos.cn>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Link: https://patch.msgid.link/20250822070424.166795-3-zhangzihuan@kylinos.cn
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Most kernel code using strncasecmp()/strncmp() passes strlen("xxx")
as the length argument. cpufreq_parse_policy() previously used
CPUFREQ_NAME_LEN (16), which is longer than the actual strings
("performance" is 11 chars, "powersave" is 9 chars).
This patch switches to strlen() for the comparison, making the
matching slightly more permissive (e.g., "powersavexxx" will now
also match "powersave"). While this is unlikely to cause functional
issues, it aligns cpufreq with common kernel style and makes the
behavior more intuitive.
Signed-off-by: Zihuan Zhang <zhangzihuan@kylinos.cn>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Link: https://patch.msgid.link/20250822070424.166795-2-zhangzihuan@kylinos.cn
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The cpuidle device's memory is leaked when cpuidle device registration
fails in acpi_processor_power_init(). Free it as appropriate.
Fixes: 3d339dcbb5 ("cpuidle / ACPI : move cpuidle_device field out of the acpi_processor_power structure")
Signed-off-by: Huisong Li <lihuisong@huawei.com>
Link: https://patch.msgid.link/20250728070612.1260859-2-lihuisong@huawei.com
[ rjw: Changed the order of the new statements, added empty line after if () ]
[ rjw: Changelog edits ]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Device configuration using configfs could be prepared long time prior
the driver load. Currently all the xe configfs entries are for things
that are important to have in the log if a non-default value is being
used. Add a info-level message about that with the individual entries
that are different than the default.
Based on previous patch by Michal Wajdeczko.
Cc: Michal Wajdeczko <michal.wajdeczko@intel.com>
Cc: John Harrison <John.C.Harrison@Intel.com>
Reviewed-by: Vinay Belgaumkar <vinay.belgaumkar@intel.com>
Link: https://lore.kernel.org/r/20250821-psmi-v5-12-34ab7550d3d8@intel.com
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
Add a few missing punctuation and line breaks and make the syntax for
code snippets common to all of them.
Reviewed-by: Dnyaneshwar Bhadane <dnyaneshwar.bhadane@intel.com>
Link: https://lore.kernel.org/r/20250821-psmi-v5-11-34ab7550d3d8@intel.com
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
The steps are roughly:
1. Load the module without binding to the device
2. Configure the desired device
3. Bind the device
Move the binding part to the "Create devices" since it's not exclusive
to the survivability_mode attribute and better document the steps.
Reviewed-by: Riana Tauro <riana.tauro@intel.com>
Link: https://lore.kernel.org/r/20250821-psmi-v5-10-34ab7550d3d8@intel.com
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
When documenting the directories, use an output similar to the `tree`
command and add VFs and missing attributes.
Reviewed-by: Dnyaneshwar Bhadane <dnyaneshwar.bhadane@intel.com>
Link: https://lore.kernel.org/r/20250821-psmi-v5-9-34ab7550d3d8@intel.com
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
Instead of the manual lock()/unlock() pattern, use guard() which will
make things easier for handling errors or early returns.
Reviewed-by: Dnyaneshwar Bhadane <dnyaneshwar.bhadane@intel.com>
Link: https://lore.kernel.org/r/20250821-psmi-v5-8-34ab7550d3d8@intel.com
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
Now that additional WAs are in place and it's possible to allocate
buffers through debugfs, add the configfs attribute to turn PSMI on.
Cc: Matt Roper <matthew.d.roper@intel.com>
Cc: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com>
Cc: John Harrison <John.C.Harrison@Intel.com>
Reviewed-by: Riana Tauro <riana.tauro@intel.com>
Link: https://lore.kernel.org/r/20250821-psmi-v5-7-34ab7550d3d8@intel.com
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
From the caller perspective reading the documentation, there's no need
to be so specific about everything the function is doing/checking. Just
document the functionality a caller cares about.
Reviewed-by: Riana Tauro <riana.tauro@intel.com>
Link: https://lore.kernel.org/r/20250821-psmi-v5-6-34ab7550d3d8@intel.com
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
This WA ensures GuC will restore the media MCFG registers at C6
exit.
Signed-off-by: Vinay Belgaumkar <vinay.belgaumkar@intel.com>
Reviewed-by: Matt Atwood <matthew.s.atwood@intel.com>
Link: https://lore.kernel.org/r/20250821-psmi-v5-5-34ab7550d3d8@intel.com
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
Enable Wa 14020001231 to block psmi interrupts during C6 entry exit
flow. It's only enabled if PSMI is enabled in runtime.
Signed-off-by: Badal Nilawar <badal.nilawar@intel.com>
Reviewed-by: Matt Atwood <matthew.s.atwood@intel.com>
Link: https://lore.kernel.org/r/20250821-psmi-v5-4-34ab7550d3d8@intel.com
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
Add match to be used on WAs for only enabling workarounds if psmi is
intended to be used.
Reviewed-by: Vinay Belgaumkar <vinay.belgaumkar@intel.com>
Link: https://lore.kernel.org/r/20250821-psmi-v5-3-34ab7550d3d8@intel.com
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
Requirement for PSMI capture is to have a physically contiguous buffer.
All the needed configuration is done by the userspace tool directly to
the GPU via mmio access.
This interface only support allocating from VRAM regions. For integrated
devices, the PSMI buffer is in SYSTEM memory and should be allocated by
userspace using hugetlbfs.
Here we add the ability to allocate a region of physically contiguous
memory by writing to debugfs file (listed below). For multi-tile devices,
the capture tool requires ability to allocate a capture buffer per tile
(VRAM region) and so user can specify a region_mask. The tool then
can mmap the buffers via direct mmap of the PCIBAR via sysfs.
To support the capture tool, 3 new debugfs entries are added:
psmi_capture_addr - physical address per VRAM region's capture buffer
psmi_capture_region_mask - select which region(s) to allocate a buffer
psmi_capture_size - size of current capture buffer
Writing psmi_capture_size will allocate new buffer of requested size per
region after freeing any current buffers.
Cc: Matt Roper <matthew.d.roper@intel.com>
Cc: Vinay Belgaumkar <vinay.belgaumkar@intel.com>
Original-author: Brian Welty <brian.welty@intel.com>
Reviewed-by: Vinay Belgaumkar <vinay.belgaumkar@intel.com> # v2
Link: https://lore.kernel.org/r/20250821-psmi-v5-2-34ab7550d3d8@intel.com
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
PSMI allows to capture data from the GPU useful for early
validation. From the kernel side there isn't much to be done, just a few
things:
1) Toggle the feature support in GuC
2) Enable some additional WAs
3) Allocate buffers
Here is the first step, with the next ones to follow. For now everything
is disabled through a check in configfs that is currently hardcoded to
disabled.
Cc: Matt Roper <matthew.d.roper@intel.com>
Cc: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com>
Cc: John Harrison <John.C.Harrison@Intel.com>
Reviewed-by: Vinay Belgaumkar <vinay.belgaumkar@intel.com>
Link: https://lore.kernel.org/r/20250821-psmi-v5-1-34ab7550d3d8@intel.com
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
Now BPF program will run with migration disabled, so it is safe
to access this_cpu_inc_return(bpf_bprintf_nest_level).
Fixes: d9c9e4db18 ("bpf: Factorize bpf_trace_printk and bpf_seq_printf")
Signed-off-by: Tao Chen <chen.dylane@linux.dev>
Signed-off-by: Andrii Nakryiko <andrii@kernel.org>
Link: https://lore.kernel.org/bpf/20250819125638.2544715-1-chen.dylane@linux.dev
Now that there's a proper SHA-1 library API, just use that instead of
the low-level SHA-1 compression function. This eliminates the need for
bpf_prog_calc_tag() to implement the SHA-1 padding itself. No
functional change; the computed tags remain the same.
Signed-off-by: Eric Biggers <ebiggers@kernel.org>
Signed-off-by: Andrii Nakryiko <andrii@kernel.org>
Acked-by: Eduard Zingerman <eddyz87@gmail.com>
Link: https://lore.kernel.org/bpf/20250811201615.564461-1-ebiggers@kernel.org
The SERDES0 instance of SERDES on the AM69 SoC is a Cadence Torrent SERDES
and it has 4 lanes which are allocated in the following manner:
Lane0 and Lane1 to PCIe1
Lane2 to PCIe3
Lane3 to USB0
Until [0], the Cadence Torrent SERDES driver only supported configuring
the SERDES for a PCIe + USB configuration whereby all lanes of the
SERDES configured for PCIe will operate at the same speed. As a result,
PCIe1 and PCIe3 instances of PCIe will either fall down to a common
speed based on the PCIe peers that they are each connected to, or, the
PCIe link could fail to be setup.
Since [0] enables support for PCIe Multilink + USB configuration, it is
now possible for the SERDES lanes allocated to PCIe1 and PCIe3 to link up
and operate at different speeds. USB continues to remain functional.
Hence, update the 'serdes0' node as well as the 'pcie1_rc' and 'pcie3_rc'
nodes to switch to the PCIe Multilink + USB configuration that is now
supported by the Cadence Torrent SERDES driver.
[0]: commit 351e07e6b2 ("phy: cadence-torrent: Add PCIe multilink + USB with same SSC register config for 100 MHz refclk")
Signed-off-by: Siddharth Vadapalli <s-vadapalli@ti.com>
Link: https://patch.msgid.link/20250819105717.372893-1-s-vadapalli@ti.com
Signed-off-by: Nishanth Menon <nm@ti.com>
Add missing address-cells 0 to the PCI interrupt node to silence W=1
warning:
k3-j721s2-main.dtsi:1431.3-1434.29: Warning (interrupt_map): /bus@100000/pcie@2910000:interrupt-map:
Missing property '#address-cells' in node /bus@100000/pcie@2910000/interrupt-controller, using 0 as fallback
Value '0' is correct because:
1. GIC interrupt controller does not have children,
2. interrupt-map property (in PCI node) consists of five components and
the fourth component "parent unit address", which size is defined by
'#address-cells' of the node pointed to by the interrupt-parent
component, is not used (=0)
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://patch.msgid.link/20250822133309.312189-2-krzysztof.kozlowski@linaro.org
Signed-off-by: Nishanth Menon <nm@ti.com>
The PM co-processor (device manager or DM) adds the ability to abort
entry to a low power mode by clearing the mode selection in the
latest version of its firmware (11.01.09) [1].
Enable the ti_sci driver to support the LPM abort call which clears the
low power mode selection of the DM. This fixes an issue where failed
system suspend attempts would cause subsequent suspends to fail.
After system suspend completes, regardless of if system suspend succeeds
or fails, the ->complete() hook in TI SCI will be called. In the
->complete() hook, a message will be sent to the DM to clear the current
low power mode selection. Clearing the low power mode selection
unconditionally will not cause any error in the DM.
[1] https://software-dl.ti.com/tisci/esd/latest/2_tisci_msgs/pm/lpm.html
Signed-off-by: Kendall Willis <k-willis@ti.com>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Link: https://patch.msgid.link/20250819195453.1094520-1-k-willis@ti.com
Signed-off-by: Nishanth Menon <nm@ti.com>
The RA620 is an active DP to HDMI converter chip, basically
no software is involved to drive it.
Add it to simple bridge to make it can be find by the drm bridge chain.
Signed-off-by: Andy Yan <andy.yan@rock-chips.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20250822063959.692098-7-andyshrk@163.com
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
RA620 is a DP to HDMI bridge converter from RADXA, which first
found be used on ROCK 5 ITX.
This chip can be used without involving software.
Signed-off-by: Andy Yan <andy.yan@rock-chips.com>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20250822063959.692098-6-andyshrk@163.com
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Function set_name_sync() uses hdev->dev_name field to send
HCI_OP_WRITE_LOCAL_NAME command, but copying from data to hdev->dev_name
is called after mgmt cmd was queued, so it is possible that function
set_name_sync() will read old name value.
This change adds name as a parameter for function hci_update_name_sync()
to avoid race condition.
Fixes: 6f6ff38a1e ("Bluetooth: hci_sync: Convert MGMT_OP_SET_LOCAL_NAME")
Signed-off-by: Pavel Shpakovskiy <pashpakovskii@salutedevices.com>
Reviewed-by: Paul Menzel <pmenzel@molgen.mpg.de>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
When a BIG sync is lost, the device should be set to "disconnected".
This ensures symmetry with the ISO path setup, where the device is
marked as "connected" once the path is established. Without this
change, the device state remains inconsistent and may lead to a
memory leak.
Fixes: b2a5f2e1c1 ("Bluetooth: hci_event: Add support for handling LE BIG Sync Lost event")
Signed-off-by: Yang Li <yang.li@amlogic.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
This attempts to detect if HCI_EV_NUM_COMP_PKTS contain an unbalanced
(more than currently considered outstanding) number of packets otherwise
it could cause the hcon->sent to underflow and loop around breaking the
tracking of the outstanding packets pending acknowledgment.
Fixes: f428091858 ("Bluetooth: Simplify num_comp_pkts_evt function")
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
When suspending, the disconnect command for an active Bluetooth
connection could be issued, but the corresponding
`HCI_EV_DISCONN_COMPLETE` event might not be received before the system
completes the suspend process. This can lead to an inconsistent state.
On resume, the controller may auto-accept reconnections from the same
device (due to suspend event filters), but these new connections are
rejected by the kernel which still has connection objects from before
suspend. Resulting in errors like:
```
kernel: Bluetooth: hci0: ACL packet for unknown connection handle 1
kernel: Bluetooth: hci0: Ignoring HCI_Connection_Complete for existing
connection
```
This is a btmon snippet that shows the issue:
```
< HCI Command: Disconnect (0x01|0x0006) plen 3
Handle: 1 Address: 78:20:A5:4A:DF:28 (Nintendo Co.,Ltd)
Reason: Remote User Terminated Connection (0x13)
> HCI Event: Command Status (0x0f) plen 4
Disconnect (0x01|0x0006) ncmd 2
Status: Success (0x00)
[...]
// Host suspends with the event filter set for the device
// On resume, the device tries to reconnect with a new handle
> HCI Event: Connect Complete (0x03) plen 11
Status: Success (0x00)
Handle: 2
Address: 78:20:A5:4A:DF:28 (Nintendo Co.,Ltd)
// Kernel ignores this event because there is an existing connection
with
// handle 1
```
By explicitly setting the connection state to BT_CLOSED we can ensure a
consistent state, even if we don't receive the disconnect complete event
in time.
Link: https://github.com/bluez/bluez/issues/1226
Fixes: 182ee45da0 ("Bluetooth: hci_sync: Rework hci_suspend_notifier")
Signed-off-by: Ludovico de Nittis <ludovico.denittis@collabora.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
When the host sends an HCI_OP_DISCONNECT command, the controller may
respond with the status HCI_ERROR_UNKNOWN_CONN_ID (0x02). E.g. this can
happen on resume from suspend, if the link was terminated by the remote
device before the event mask was correctly set.
This is a btmon snippet that shows the issue:
```
> ACL Data RX: Handle 3 flags 0x02 dlen 12
L2CAP: Disconnection Request (0x06) ident 5 len 4
Destination CID: 65
Source CID: 72
< ACL Data TX: Handle 3 flags 0x00 dlen 12
L2CAP: Disconnection Response (0x07) ident 5 len 4
Destination CID: 65
Source CID: 72
> ACL Data RX: Handle 3 flags 0x02 dlen 12
L2CAP: Disconnection Request (0x06) ident 6 len 4
Destination CID: 64
Source CID: 71
< ACL Data TX: Handle 3 flags 0x00 dlen 12
L2CAP: Disconnection Response (0x07) ident 6 len 4
Destination CID: 64
Source CID: 71
< HCI Command: Set Event Mask (0x03|0x0001) plen 8
Mask: 0x3dbff807fffbffff
Inquiry Complete
Inquiry Result
Connection Complete
Connection Request
Disconnection Complete
Authentication Complete
[...]
< HCI Command: Disconnect (0x01|0x0006) plen 3
Handle: 3 Address: 78:20:A5:4A:DF:28 (Nintendo Co.,Ltd)
Reason: Remote User Terminated Connection (0x13)
> HCI Event: Command Status (0x0f) plen 4
Disconnect (0x01|0x0006) ncmd 1
Status: Unknown Connection Identifier (0x02)
```
Currently, the hci_cs_disconnect function treats any non-zero status
as a command failure. This can be misleading because the connection is
indeed being terminated and the controller is confirming that is has no
knowledge of that connection handle. Meaning that the initial request of
disconnecting a device should be treated as done.
With this change we allow the function to proceed, following the success
path, which correctly calls `mgmt_device_disconnected` and ensures a
consistent state.
Link: https://github.com/bluez/bluez/issues/1226
Fixes: 182ee45da0 ("Bluetooth: hci_sync: Rework hci_suspend_notifier")
Signed-off-by: Ludovico de Nittis <ludovico.denittis@collabora.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Test cgroup v2 freezer time stat. Freezer time accounting should
be independent of other cgroups in the hierarchy and should increase
iff a cgroup is CGRP_FREEZE (regardless of whether it reaches
CGRP_FROZEN).
Skip these tests on systems without freeze time accounting.
Signed-off-by: Tiffany Yang <ynaffit@google.com>
Cc: Michal Koutný <mkoutny@suse.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
There isn't yet a clear way to identify a set of "lost" time that
everyone (or at least a wider group of users) cares about. However,
users can perform some delay accounting by iterating over components of
interest. This patch allows cgroup v2 freezing time to be one of those
components.
Track the cumulative time that each v2 cgroup spends freezing and expose
it to userland via a new local stat file in cgroupfs. Thank you to
Michal, who provided the ASCII art in the updated documentation.
To access this value:
$ mkdir /sys/fs/cgroup/test
$ cat /sys/fs/cgroup/test/cgroup.stat.local
freeze_time_total 0
Ensure consistent freeze time reads with freeze_seq, a per-cgroup
sequence counter. Writes are serialized using the css_set_lock.
Signed-off-by: Tiffany Yang <ynaffit@google.com>
Cc: Tejun Heo <tj@kernel.org>
Cc: Michal Koutný <mkoutny@suse.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
A hung task can occur during [1] LTP cgroup testing when repeatedly
mounting/unmounting perf_event and net_prio controllers with
systemd.unified_cgroup_hierarchy=1. The hang manifests in
cgroup_lock_and_drain_offline() during root destruction.
Related case:
cgroup_fj_function_perf_event cgroup_fj_function.sh perf_event
cgroup_fj_function_net_prio cgroup_fj_function.sh net_prio
Call Trace:
cgroup_lock_and_drain_offline+0x14c/0x1e8
cgroup_destroy_root+0x3c/0x2c0
css_free_rwork_fn+0x248/0x338
process_one_work+0x16c/0x3b8
worker_thread+0x22c/0x3b0
kthread+0xec/0x100
ret_from_fork+0x10/0x20
Root Cause:
CPU0 CPU1
mount perf_event umount net_prio
cgroup1_get_tree cgroup_kill_sb
rebind_subsystems // root destruction enqueues
// cgroup_destroy_wq
// kill all perf_event css
// one perf_event css A is dying
// css A offline enqueues cgroup_destroy_wq
// root destruction will be executed first
css_free_rwork_fn
cgroup_destroy_root
cgroup_lock_and_drain_offline
// some perf descendants are dying
// cgroup_destroy_wq max_active = 1
// waiting for css A to die
Problem scenario:
1. CPU0 mounts perf_event (rebind_subsystems)
2. CPU1 unmounts net_prio (cgroup_kill_sb), queuing root destruction work
3. A dying perf_event CSS gets queued for offline after root destruction
4. Root destruction waits for offline completion, but offline work is
blocked behind root destruction in cgroup_destroy_wq (max_active=1)
Solution:
Split cgroup_destroy_wq into three dedicated workqueues:
cgroup_offline_wq – Handles CSS offline operations
cgroup_release_wq – Manages resource release
cgroup_free_wq – Performs final memory deallocation
This separation eliminates blocking in the CSS free path while waiting for
offline operations to complete.
[1] https://github.com/linux-test-project/ltp/blob/master/runtest/controllers
Fixes: 334c3679ec ("cgroup: reimplement rebind_subsystems() using cgroup_apply_control() and friends")
Reported-by: Gao Yingjie <gaoyingjie@uniontech.com>
Signed-off-by: Chen Ridong <chenridong@huawei.com>
Suggested-by: Teju Heo <tj@kernel.org>
Signed-off-by: Tejun Heo <tj@kernel.org>
This attempts to make unacked packet handling more robust by detecting
if there are no connections left then restore all buffers of the
respective pool.
Fixes: 5638d9ea9c ("Bluetooth: hci_conn: Fix not restoring ISO buffer count on disconnect")
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
idpf has a limit on number of scatter-gather frags
that can be used per segment.
Currently, idpf_tx_start() checks if the limit is hit
and forces a linearization of the whole packet.
This requires high order allocations that can fail
under memory pressure. A full size BIG-TCP packet
would require order-7 alocation on x86_64 :/
We can move the check earlier from idpf_features_check()
for TSO packets, to force GSO in this case, removing the
cost of a big copy.
This means that a linearization will eventually happen
with sizes smaller than one MSS.
__idpf_chk_linearize() is renamed to idpf_chk_tso_segment()
and moved to idpf_lib.c
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Cc: Jacob Keller <jacob.e.keller@intel.com>
Cc: Madhu Chittim <madhu.chittim@intel.com>
Cc: Pavan Kumar Linga <pavan.kumar.linga@intel.com>
Cc: Willem de Bruijn <willemb@google.com>
Cc: Andrew Lunn <andrew+netdev@lunn.ch>
Reviewed-by: Joshua Hay <joshua.a.hay@intel.com>
Tested-by: Brian Vazquez <brianvv@google.com>
Acked-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Link: https://patch.msgid.link/20250818195934.757936-1-edumazet@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The Free Software Foundation does not reside in "675 Mass Ave, Cambridge"
anymore, so no need to mention that address in the source code here. But
instead of updating the address to their current location, just drop the
license boilerplate text and use a proper SPDX license identifier instead. The
text talks about the "GNU *Library* General Public License" and "any later
version", so LGPL-2.0+ is the right choice here.
[ bp: Massage commit message. ]
Signed-off-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: Borislav Petkov (AMD) <bp@alien8.de>
Link: https://lore.kernel.org/20250801084531.34089-1-thuth@redhat.com
Commit fd40a63c63 ("drm/atomic: Let drivers decide which planes to
async flip") unintentionally disallowed no-op changes on non-primary
planes that the driver doesn't allow async flips on. This broke async
flips for compositors that disable the cursor plane in every async
atomic commit. To fix that, change drm_atomic_set_property to again
only run atomic_async_check if the plane would actually be changed by
the atomic commit.
Fixes: fd40a63c63 ("drm/atomic: Let drivers decide which planes to async flip")
Closes: https://gitlab.freedesktop.org/drm/amd/-/issues/4263
Signed-off-by: Xaver Hugl <xaver.hugl@kde.org>
Reviewed-by: André Almeida <andrealmeid@igalia.com>
Link: https://lore.kernel.org/r/20250822152849.87843-1-xaver.hugl@kde.org
[andrealmeid: fix checkpatch warning]
Signed-off-by: André Almeida <andrealmeid@igalia.com>
Current minimum required version of binutils is 2.30, which supports RDPKRU and
WRPKRU instruction mnemonics.
Replace the byte-wise specification of RDPKRU and WRPKRU with these proper
mnemonics.
No functional change intended.
Signed-off-by: Uros Bizjak <ubizjak@gmail.com>
Signed-off-by: Borislav Petkov (AMD) <bp@alien8.de>
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Link: https://lore.kernel.org/20250616083611.157740-1-ubizjak@gmail.com
There are two registers filled in when reading data from
pcode besides the mailbox itself. Currently, we allow a NULL
value for the second of these two (data1) and assume the first
is defined. However, many of the routines that are calling
this function assume that pcode will ignore the value being
passed in and so leave that first value (data0) defined but
uninitialized. To be safe, make sure this value is always
initialized to something (0 generally) in the event pcode
behavior changes and starts using this value.
v2: Fix sob/author
Signed-off-by: Stuart Summers <stuart.summers@intel.com>
Reviewed-by: Jonathan Cavitt <jonathan.cavitt@intel.com>
Link: https://lore.kernel.org/r/20250819201054.393220-1-stuart.summers@intel.com
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
This patch adds tests for the new jeq and jne logic in
is_scalar_branch_taken. The following shows the first test failing
before the previous patch is applied. Once the previous patch is
applied, the verifier can use the tnum values to deduce that instruction
7 is dead code.
0: call bpf_get_prandom_u32#7 ; R0_w=scalar()
1: w0 = w0 ; R0_w=scalar(smin=0,smax=umax=0xffffffff,var_off=(0x0; 0xffffffff))
2: r0 >>= 30 ; R0_w=scalar(smin=smin32=0,smax=umax=smax32=umax32=3,var_off=(0x0; 0x3))
3: r0 <<= 30 ; R0_w=scalar(smin=0,smax=umax=umax32=0xc0000000,smax32=0x40000000,var_off=(0x0; 0xc0000000))
4: r1 = r0 ; R0_w=scalar(id=1,smin=0,smax=umax=umax32=0xc0000000,smax32=0x40000000,var_off=(0x0; 0xc0000000)) R1_w=scalar(id=1,smin=0,smax=umax=umax32=0xc0000000,smax32=0x40000000,var_off=(0x0; 0xc0000000))
5: r1 += 1024 ; R1_w=scalar(smin=umin=umin32=1024,smax=umax=umax32=0xc0000400,smin32=0x80000400,smax32=0x40000400,var_off=(0x400; 0xc0000000))
6: if r1 != r0 goto pc+1 ; R0_w=scalar(id=1,smin=umin=umin32=1024,smax=umax=umax32=0xc0000000,smin32=0x80000400,smax32=0x40000000,var_off=(0x400; 0xc0000000)) R1_w=scalar(smin=umin=umin32=1024,smax=umax=umax32=0xc0000000,smin32=0x80000400,smax32=0x40000400,var_off=(0x400; 0xc0000000))
7: r10 = 0
frame pointer is read only
Signed-off-by: Paul Chaignon <paul.chaignon@gmail.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Eduard Zingerman <eddyz87@gmail.com>
Link: https://lore.kernel.org/bpf/550004f935e2553bdb2fb1f09cbde7d0452112d0.1755694148.git.paul.chaignon@gmail.com
In the following toy program (reg states minimized for readability), R0
and R1 always have different values at instruction 6. This is obvious
when reading the program but cannot be guessed from ranges alone as
they overlap (R0 in [0; 0xc0000000], R1 in [1024; 0xc0000400]).
0: call bpf_get_prandom_u32#7 ; R0_w=scalar()
1: w0 = w0 ; R0_w=scalar(var_off=(0x0; 0xffffffff))
2: r0 >>= 30 ; R0_w=scalar(var_off=(0x0; 0x3))
3: r0 <<= 30 ; R0_w=scalar(var_off=(0x0; 0xc0000000))
4: r1 = r0 ; R1_w=scalar(var_off=(0x0; 0xc0000000))
5: r1 += 1024 ; R1_w=scalar(var_off=(0x400; 0xc0000000))
6: if r1 != r0 goto pc+1
Looking at tnums however, we can deduce that R1 is always different from
R0 because their tnums don't agree on known bits. This patch uses this
logic to improve is_scalar_branch_taken in case of BPF_JEQ and BPF_JNE.
This change has a tiny impact on complexity, which was measured with
the Cilium complexity CI test. That test covers 72 programs with
various build and load time configurations for a total of 970 test
cases. For 80% of test cases, the patch has no impact. On the other
test cases, the patch decreases complexity by only 0.08% on average. In
the best case, the verifier needs to walk 3% less instructions and, in
the worst case, 1.5% more. Overall, the patch has a small positive
impact, especially for our largest programs.
Signed-off-by: Paul Chaignon <paul.chaignon@gmail.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Eduard Zingerman <eddyz87@gmail.com>
Acked-by: Shung-Hsi Yu <shung-hsi.yu@suse.com>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Link: https://lore.kernel.org/bpf/be3ee70b6e489c49881cb1646114b1d861b5c334.1755694147.git.paul.chaignon@gmail.com
The DTS code coding style expects exactly one space around '=' or '{'
characters.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Link: https://lore.kernel.org/r/20250819131736.86862-2-krzysztof.kozlowski@linaro.org
Signed-off-by: Claudiu Beznea <claudiu.beznea@tuxon.dev>
Rockchip RK3528 ships a naneng-combphy that is shared by PCIe and USB
3.0 controllers. Describe it and the pipe-phy grf which it depends on.
Signed-off-by: Yao Zi <ziyao@disroot.org>
Link: https://lore.kernel.org/r/20250728102947.38984-8-ziyao@disroot.org
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
The function cpa_flush() calls __flush_tlb_one_kernel() and
flush_tlb_all().
Replacing that with a call to flush_tlb_kernel_range() allows
cpa_flush() to make use of INVLPGB or RAR without any additional
changes.
Initialize invlpgb_count_max to 1, since flush_tlb_kernel_range()
can now be called before invlpgb_count_max has been initialized
to the value read from CPUID.
[riel: remove now unused __cpa_flush_tlb]
Signed-off-by: Yu-cheng Yu <yu-cheng.yu@intel.com>
Signed-off-by: Rik van Riel <riel@surriel.com>
Signed-off-by: Dave Hansen <dave.hansen@linux.intel.com>
Acked-by: Dave Hansen <dave.hansen@linux.intel.com>
Link: https://lore.kernel.org/all/20250606171112.4013261-4-riel%40surriel.com
Dimitri Daskalakis says:
====================
selftests: Test XDP_TX for single-buffer
Ensure single buffer XDP functions correctly by covering the following cases:
1) Zero size payload
2) Full MTU
3) Single buffer packets through a multi-buffer XDP program
These changes were tested with netdevsim and fbnic.
# ./ksft-net-drv/drivers/net/xdp.py
TAP version 13
1..10
ok 1 xdp.test_xdp_native_pass_sb
ok 2 xdp.test_xdp_native_pass_mb
ok 3 xdp.test_xdp_native_drop_sb
ok 4 xdp.test_xdp_native_drop_mb
ok 5 xdp.test_xdp_native_tx_sb
ok 6 xdp.test_xdp_native_tx_mb
# Failed run: pkt_sz 2048, offset 1. Last successful run: pkt_sz 1024, offset 256. Reason: Adjustment failed
ok 7 xdp.test_xdp_native_adjst_tail_grow_data
ok 8 xdp.test_xdp_native_adjst_tail_shrnk_data
# Failed run: pkt_sz 512, offset -256. Last successful run: pkt_sz 512, offset -128. Reason: Adjustment failed
ok 9 xdp.test_xdp_native_adjst_head_grow_data
# Failed run: pkt_sz (2048) > HDS threshold (1536) and offset 64 > 48
ok 10 xdp.test_xdp_native_adjst_head_shrnk_data
# Totals: pass:10 fail:0 xfail:0 xpass:0 skip:0 error:0
====================
Link: https://patch.msgid.link/20250821014023.1481662-1-dimitri.daskalakis1@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
