The ethernet node has two MAC subnodes and cannot use the default
address/size cells: set address cells to 1 and size cells to 0.
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Align the name of the regulator with the design schematic. Also fix up
the gpio property to the new "gpios" property name, and add the
GPIO_ACTIVE_HIGH flag. The flag is actively ignored in Linux in favor of
the old "enable-active-high" property; nevertheless it is the correct
description.
Signed-off-by: Chen-Yu Tsai <wenst@chromium.org>
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Following the changes in the binding for the SafeXcel crypto
engine, add a SoC specific compatible to the existing crypto
node and, while at it, also change the fallback compatible to
inside-secure,safexcel-eip97ies as the eip97 one is deprecated.
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Add the required pinmux and assign the right interrupts-extended
to the DA9211 regulator (PIO pin 15).
Reviewed-by: Matthias Brugger <matthias.bgg@gmail.com>
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
The MT6332 PMIC leds node was named "mt6332-led", however, the
binding rightfully enforces using the generic node name "leds".
Change it to the latter to resolve dtbs_check warnings.
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Add the "mediatek,mt6795-scpsys" compatible to the SCPSYS node
and remove #power-domain-cells (retaining it only in the power
controller subnode) to resolve dtbs_check warnings.
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
The ldo-vcamio regulator is named "vcam_io", however, the binding
only allows "vcamio" as name: change it to the latter to resolve
a dtbs_check warning.
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Add the UHS state pins for the MMC1 and MMC2 controllers and,
while at it, also add the correct drive strength parameters
for the default pin states for those two.
Reviewed-by: Chen-Yu Tsai <wenst@chromium.org>
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Remove the clock-stretch-ns property from i2c2, as it has always
been (and still is) unused.
Reviewed-by: Chen-Yu Tsai <wenst@chromium.org>
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
The only reason to have a regulator in the thermal node is to keep
the CPU cores up while reading temperatures, but this is incorrect
because the AUXADC Thermal IP doesn't need any regulators to work,
at all.
Since the thermal node was inherited only for adding vregs, remove
it entirely.
This change is safe also because, among other things, the actual
driver never used those regulators anyway.
This also fixes a dtbs_check warning.
Reviewed-by: Chen-Yu Tsai <wenst@chromium.org>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Since only a single port is present, remove the inner `ports`
parent node and just declare the single port as `port`.
Reviewed-by: Chen-Yu Tsai <wenst@chromium.org>
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Change the node name for Marvell SD8897 SDIO Bluetooth from
`btmrvl@2` to `bluetooth@2` to fix a dtbs_check warning.
While at it, also change the WiFi one from `mwifiex@1" to a
generic "wifi@1" and reorder the nodes so that wifi@1 comes
before bluetooth@2.
Reviewed-by: Chen-Yu Tsai <wenst@chromium.org>
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Change all of the pinmux main nodes to have a "-pins" suffix to
satisfy devicetree bindings checks.
Reviewed-by: Chen-Yu Tsai <wenst@chromium.org>
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Rename "piins-bt-wakeup" to "pins-bt-wakeup" to fix a dtbs_check
warning happening due to this typo.
Fixes: 055ef10ccd ("arm64: dts: mt8183: Add jacuzzi pico/pico6 board")
Reviewed-by: Chen-Yu Tsai <wenst@chromium.org>
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
In spi2's flash@0 there is only one `partitions` subnode: this
alone makes specifying address and size cells useless, but then
this subnode has no address and no size, which even makes the
currently declared address/size cells wrong.
Fixes: 869b3bb5ad ("arm64: dts: mediatek: mt7981b-openwrt-one: Enable SPI NOR")
Reviewed-by: Chen-Yu Tsai <wenst@chromium.org>
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Change the Murata NCM03WF104 node name from "thermal-sensor" to
"thermistor" (as that's what it is, after all), and change all
of the pinmux main nodes to have a "-pins" suffix to satisfy
devicetree bindings checks.
Reviewed-by: Chen-Yu Tsai <wenst@chromium.org>
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Fix the pinctrl node names to adhere to the bindings, as the main
pin node is supposed to be named like "uart0-pins" and the pinmux
node named like "pins-bus".
While at it, also cleanup all of the MTK_DRIVE_(x)mA by changing
that to just the (x) number.
Reviewed-by: Chen-Yu Tsai <wenst@chromium.org>
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Arnd pointed out that having firmware-name in the device tree is wrong.
Drop it.
Signed-off-by: Chen-Yu Tsai <wenst@chromium.org>
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
No functional change but will allow other dts including this one to
override the interrupts, for eint support for instance, without having
to delete the 'interrupts' property.
Signed-off-by: Gary Bisson <bisson.gary@gmail.com>
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Ezurio is the new name of Laird Connectivity after it acquired Boundary
Devices.
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@oss.qualcomm.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Gary Bisson <bisson.gary@gmail.com>
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Add in the sound node a new dai-link for ETDM3_OUT_BE to add the sound
output support through the HDMI TX connector.
Signed-off-by: Louis-Alexis Eyraud <louisalexis.eyraud@collabora.com>
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Add a definition for the on-board HDMI connector, enable and add
the relevant configuration for the HDMI PHY and controller, and
define the pins used by those.
Signed-off-by: Louis-Alexis Eyraud <louisalexis.eyraud@collabora.com>
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Add in the sound node a new dai-link for ETDM3_OUT_BE to add the sound
output support through the HDMI TX connector.
Signed-off-by: Louis-Alexis Eyraud <louisalexis.eyraud@collabora.com>
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Add a definition for the on-board HDMI connector, enable and add
the relevant configuration for the HDMI PHY and controller, and
define the pins used by those.
Signed-off-by: Louis-Alexis Eyraud <louisalexis.eyraud@collabora.com>
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Add in the sound node a new dai-link for ETDM3_OUT_BE to add the sound
output support through the HDMI connector.
Signed-off-by: Louis-Alexis Eyraud <louisalexis.eyraud@collabora.com>
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Add a node for the HDMI-A connector found on this board, then
configure the display pipeline and enable the required DPI1
interface, HDMI controller, its integrated DDC and the HDMI
PHY to enable support for the HDMI output provided by these EVKs.
Signed-off-by: Louis-Alexis Eyraud <louisalexis.eyraud@collabora.com>
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Add all of the nodes that are required to enable HDMI output,
including ones describing the HDMI PHY, Controller and DDC,
and the Digital Parallel Interface instance that is internally
connected to the HDMI Controller.
All of the added nodes are disabled by default as usage is
board dependent.
Signed-off-by: Louis-Alexis Eyraud <louisalexis.eyraud@collabora.com>
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Add all of the nodes that are required to enable HDMI output,
including ones describing the HDMI PHY, Controller and DDC,
and the Digital Parallel Interface instance that is internally
connected to the HDMI Controller.
All of the added nodes are disabled by default as usage is
board dependent.
Signed-off-by: Louis-Alexis Eyraud <louisalexis.eyraud@collabora.com>
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Enable Dual-band WiFI 6 functionality on the Openwrt One
Signed-off-by: Sjoerd Simons <sjoerd@collabora.com>
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Add required memory region for the builtin wifi block.
Signed-off-by: Sjoerd Simons <sjoerd@collabora.com>
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Disable the wifi block by default as it won't function properly without
at least pin muxing.
This doesn't enable wifi on any of the existing mt7981b devices as a
required memory-region property is missing, causing the driver to fail
probing anyway.
Signed-off-by: Sjoerd Simons <sjoerd@collabora.com>
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Enable the Ethernet subsystem on OpenWrt One board with dual-MAC
configuration:
- GMAC0: Connected to external Airoha EN8811H 2.5GbE PHY via SGMII
(2500base-x mode) for WAN connectivity with LED indicators
- GMAC1: Connected to internal MT7981 1GbE PHY (GMII mode) for LAN
Ethernet aliases are defined to provide consistent network interface
naming (ethernet0 = LAN, ethernet1 = WAN).
Signed-off-by: Sjoerd Simons <sjoerd@collabora.com>
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Add device tree nodes for the Ethernet subsystem on MT7981B SoC,
including:
- Ethernet MAC controller with dual GMAC support
- Wireless Ethernet Dispatch (WED)
- SGMII PHY controllers for high-speed Ethernet interfaces
- Reserved memory regions for WiFi offload processor
Signed-off-by: Sjoerd Simons <sjoerd@collabora.com>
[Angelo: Removed useless address/size cells from main eth node]
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Enable the PCIe controller and USB3 XHCI host on the OpenWrt One
board. The USB controller is configured for USB 2.0 only mode, as the
shared USB3/PCIe PHY is dedicated to PCIe functionality on this board.
Signed-off-by: Sjoerd Simons <sjoerd@collabora.com>
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Add device tree nodes for PCIe controller and USB3 XHCI host
controller on MT7981B SoC. Both controllers share the USB3 PHY
which can be configured for either USB3 or PCIe operation.
The USB3 XHCI controller supports USB 2.0 and USB 3.0 SuperSpeed
operation. The PCIe controller is compatible with PCIe Gen2
specifications.
Also add the topmisc syscon node required for USB/PCIe PHY
multiplexing.
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Sjoerd Simons <sjoerd@collabora.com>
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
The endpoint IDs in the display graph are expected to match the
associated display path number, i.e. all endpoints connected to
mmsys_ep_main must have reg = <0> and all endpoints connected to
mmsys_ep_ext must have reg = <1>.
Add the missing ID to all endpoints in the display graph, based on
mt8365.dtsi as an existing example that does this correctly.
Fixes: e72d63fa05 ("arm64: dts: mediatek: mt8183: Migrate to display controller OF graph")
Reported-by: Evans Jahja <evansjahja13@gmail.com>
Closes: https://lore.kernel.org/linux-mediatek/CAAq5pW9o3itC0G16LnJO7KMAQ_XoqXUpB=cuJ_7e3-H11zKd5Q@mail.gmail.com/
Tested-by: Chen-Yu Tsai <wenst@chromium.org>
Signed-off-by: Otto Pflüger <otto.pflueger@abscue.de>
[Angelo: Fixed dtbs_check issues]
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
It's a requirement that DT overlays be applied at build time in order to
validate them as overlays are not validated on their own.
Add missing target for mt8395-radxa hd panel overlay.
Fixes: 4c8ff61199 ("arm64: dts: mediatek: mt8395-radxa-nio-12l: Add Radxa 8 HD panel")
Signed-off-by: Rob Herring (Arm) <robh@kernel.org>
Signed-off-by: Frank Wunderlich <frank-w@public-files.de>
Acked-by: AngeloGioacchino Del Regno <angelogiaocchino.delregno@collabora.com>
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Build devicetree binaries for testing overlays and providing users
full dtb without using overlays for Bananapi R4 (pro) variants.
Signed-off-by: Frank Wunderlich <frank-w@public-files.de>
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
DTS coding style prefers hyphens instead of underscores in the node
names. Change should be safe, because node names are not considered an
ABI.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@oss.qualcomm.com>
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
The only core fix is in doc; all the others are in drivers, with the
biggest impacts in libsas being the rollback on error handling and in
ufs coming from a couple of error handling fixes, one causing a crash
if it's activated before scanning and the other fixing W-LUN
resumption.
Signed-off-by: James E.J. Bottomley <James.Bottomley@HansenPartnership.com>
-----BEGIN PGP SIGNATURE-----
iLgEABMIAGAWIQTnYEDbdso9F2cI+arnQslM7pishQUCaT4RWBsUgAAAAAAEAA5t
YW51MiwyLjUrMS4xMSwyLDImHGphbWVzLmJvdHRvbWxleUBoYW5zZW5wYXJ0bmVy
c2hpcC5jb20ACgkQ50LJTO6YrIVfSgEA23oY0kPjLLkNj4KAjLoWVPmZ/5efKw49
m6YUwfvzTS8BAIq4eFHVecwAM8FAe9NwuOKgO5d9u6epAy6wzBeP2jly
=cpHq
-----END PGP SIGNATURE-----
Merge tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI fixes from James Bottomley:
"The only core fix is in doc; all the others are in drivers, with the
biggest impacts in libsas being the rollback on error handling and in
ufs coming from a couple of error handling fixes, one causing a crash
if it's activated before scanning and the other fixing W-LUN
resumption"
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
scsi: ufs: qcom: Fix confusing cleanup.h syntax
scsi: libsas: Add rollback handling when an error occurs
scsi: device_handler: Return error pointer in scsi_dh_attached_handler_name()
scsi: ufs: core: Fix a deadlock in the frequency scaling code
scsi: ufs: core: Fix an error handler crash
scsi: Revert "scsi: libsas: Fix exp-attached device scan after probe failure scanned in again after probe failed"
scsi: ufs: core: Fix RPMB link error by reversing Kconfig dependencies
scsi: qla4xxx: Use time conversion macros
scsi: qla2xxx: Enable/disable IRQD_NO_BALANCING during reset
scsi: ipr: Enable/disable IRQD_NO_BALANCING during reset
scsi: imm: Fix use-after-free bug caused by unfinished delayed work
scsi: target: sbp: Remove KMSG_COMPONENT macro
scsi: core: Correct documentation for scsi_device_quiesce()
scsi: mpi3mr: Prevent duplicate SAS/SATA device entries in channel 1
scsi: target: Reset t_task_cdb pointer in error case
scsi: ufs: core: Fix EH failure after W-LUN resume error
client from Max, a fix that hardens osdmap parsing code from myself
(marked for stable) and a few assorted fixups.
-----BEGIN PGP SIGNATURE-----
iQFHBAABCAAxFiEEydHwtzie9C7TfviiSn/eOAIR84sFAmk8YxITHGlkcnlvbW92
QGdtYWlsLmNvbQAKCRBKf944AhHzi702B/9Mfj0HQSAaWCyMz6GJAv8+1ijVTSbG
nTFeMmipYZhPn188OvWqHsf1cw9rWY0fzenIEW05Tk3YmMvYdeRmCcOkZdeG06xw
um8XxX4L8315E0b98CCpQpVa02ux7XoNtBPjeHccl8PEErJQgQJrQ3Cc/C8kk5U5
a0KlfeVRXYWkOPJva3+wosOu0t9QgJ9ABt5stqcvYDfdkKfvatQMBN3N1nNRKkFH
yhNPv+nRtypSk8jiHhKeeCVmosC0L7MnKuO593vDr761cY5mKrgKFqc2LLlPF6r0
/p13s5SG6X38RUegWCjcK4XRJAzVcR/tyod8LkVVp8d5DC/ptcyy8H+I
=h1gC
-----END PGP SIGNATURE-----
Merge tag 'ceph-for-6.19-rc1' of https://github.com/ceph/ceph-client
Pull ceph updates from Ilya Dryomov:
"We have a patch that adds an initial set of tracepoints to the MDS
client from Max, a fix that hardens osdmap parsing code from myself
(marked for stable) and a few assorted fixups"
* tag 'ceph-for-6.19-rc1' of https://github.com/ceph/ceph-client:
rbd: stop selecting CRC32, CRYPTO, and CRYPTO_AES
ceph: stop selecting CRC32, CRYPTO, and CRYPTO_AES
libceph: make decode_pool() more resilient against corrupted osdmaps
libceph: Amend checking to fix `make W=1` build breakage
ceph: Amend checking to fix `make W=1` build breakage
ceph: add trace points to the MDS client
libceph: fix log output race condition in OSD client
Signed-off-by: Ingo Molnar <mingo@kernel.org>
-----BEGIN PGP SIGNATURE-----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=jbkd
-----END PGP SIGNATURE-----
Merge tag 'smp-urgent-2025-12-12' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull CPU hotplug fix from Ingo Molnar:
- Fix CPU hotplug callbacks to disable interrupts on UP kernels
* tag 'smp-urgent-2025-12-12' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
cpu: Make atomic hotplug callbacks run with interrupts disabled on UP
