commit fe6a6de669 upstream.
The following fixes are done for tcc sysfs interface:
- TCC is 6 bits only from bit 29-24
- TCC of 0 is valid
- When BIT(31) is set, this register is read only
- Check for invalid tcc value
- Error for negative values
Fixes: fdf4f2fb8e ("drivers: thermal: processor_thermal_device: Export sysfs interface for TCC offset")
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Cc: stable@vger.kernel.org
Acked-by: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20210628215803.75038-1-srinivas.pandruvada@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2253042d86 upstream.
When an IPMI watchdog timer is being stopped in ipmi_close() or
ipmi_ioctl(WDIOS_DISABLECARD), the current watchdog action is updated to
WDOG_TIMEOUT_NONE and _ipmi_set_timeout(IPMI_SET_TIMEOUT_NO_HB) is called
to install this action. The latter function ends up invoking
__ipmi_set_timeout() which makes the actual 'Set Watchdog Timer' IPMI
request.
For IPMI 1.0, this operation results in fully stopping the watchdog timer.
For IPMI >= 1.5, function __ipmi_set_timeout() always specifies the "don't
stop" flag in the prepared 'Set Watchdog Timer' IPMI request. This causes
that the watchdog timer has its action correctly updated to 'none' but the
timer continues to run. A problem is that IPMI firmware can then still log
an expiration event when the configured timeout is reached, which is
unexpected because the watchdog timer was requested to be stopped.
The patch fixes this problem by not setting the "don't stop" flag in
__ipmi_set_timeout() when the current action is WDOG_TIMEOUT_NONE which
results in stopping the watchdog timer. This makes the behaviour for
IPMI >= 1.5 consistent with IPMI 1.0. It also matches the logic in
__ipmi_heartbeat() which does not allow to reset the watchdog if the
current action is WDOG_TIMEOUT_NONE as that would start the timer.
Signed-off-by: Petr Pavlu <petr.pavlu@suse.com>
Message-Id: <10a41bdc-9c99-089c-8d89-fa98ce5ea080@suse.com>
Cc: stable@vger.kernel.org
Signed-off-by: Corey Minyard <cminyard@mvista.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit fca41af18e upstream.
fw_cfg_showrev() is called by an indirect call in kobj_attr_show(),
which violates clang's CFI checking because fw_cfg_showrev()'s second
parameter is 'struct attribute', whereas the ->show() member of 'struct
kobj_structure' expects the second parameter to be of type 'struct
kobj_attribute'.
$ cat /sys/firmware/qemu_fw_cfg/rev
3
$ dmesg | grep "CFI failure"
[ 26.016832] CFI failure (target: fw_cfg_showrev+0x0/0x8):
Fix this by converting fw_cfg_rev_attr to 'struct kobj_attribute' where
this would have been caught automatically by the incompatible pointer
types compiler warning. Update fw_cfg_showrev() accordingly.
Fixes: 75f3e8e47f ("firmware: introduce sysfs driver for QEMU's fw_cfg device")
Link: https://github.com/ClangBuiltLinux/linux/issues/1299
Signed-off-by: Nathan Chancellor <nathan@kernel.org>
Reviewed-by: Sami Tolvanen <samitolvanen@google.com>
Tested-by: Sedat Dilek <sedat.dilek@gmail.com>
Reviewed-by: Sami Tolvanen <samitolvanen@google.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Signed-off-by: Kees Cook <keescook@chromium.org>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20210211194258.4137998-1-nathan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 26b0ce8dd3 upstream.
As reported by Alex Sergeev, the i40e driver is incrementing the PTP
clock at 40Gb speeds when linked at 5Gb. Fix this bug by making
sure that the right multiplier is selected when linked at 5Gb.
Fixes: 3dbdd6c2f7 ("i40e: Add support for 5Gbps cards")
Cc: stable@vger.kernel.org
Reported-by: Alex Sergeev <asergeev@carbonrobotics.com>
Suggested-by: Alex Sergeev <asergeev@carbonrobotics.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1f9482aa8d upstream.
We can deadlock when rmmod'ing the driver or going through firmware
reset, because the cfg80211_unregister_wdev() has to bring down the link
for us, ... which then grab the same wiphy lock.
nl80211_del_interface() already handles a very similar case, with a nice
description:
/*
* We hold RTNL, so this is safe, without RTNL opencount cannot
* reach 0, and thus the rdev cannot be deleted.
*
* We need to do it for the dev_close(), since that will call
* the netdev notifiers, and we need to acquire the mutex there
* but don't know if we get there from here or from some other
* place (e.g. "ip link set ... down").
*/
mutex_unlock(&rdev->wiphy.mtx);
...
Do similarly for mwifiex teardown, by ensuring we bring the link down
first.
Sample deadlock trace:
[ 247.103516] INFO: task rmmod:2119 blocked for more than 123 seconds.
[ 247.110630] Not tainted 5.12.4 #5
[ 247.115796] "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message.
[ 247.124557] task:rmmod state:D stack: 0 pid: 2119 ppid: 2114 flags:0x00400208
[ 247.133905] Call trace:
[ 247.136644] __switch_to+0x130/0x170
[ 247.140643] __schedule+0x714/0xa0c
[ 247.144548] schedule_preempt_disabled+0x88/0xf4
[ 247.149714] __mutex_lock_common+0x43c/0x750
[ 247.154496] mutex_lock_nested+0x5c/0x68
[ 247.158884] cfg80211_netdev_notifier_call+0x280/0x4e0 [cfg80211]
[ 247.165769] raw_notifier_call_chain+0x4c/0x78
[ 247.170742] call_netdevice_notifiers_info+0x68/0xa4
[ 247.176305] __dev_close_many+0x7c/0x138
[ 247.180693] dev_close_many+0x7c/0x10c
[ 247.184893] unregister_netdevice_many+0xfc/0x654
[ 247.190158] unregister_netdevice_queue+0xb4/0xe0
[ 247.195424] _cfg80211_unregister_wdev+0xa4/0x204 [cfg80211]
[ 247.201816] cfg80211_unregister_wdev+0x20/0x2c [cfg80211]
[ 247.208016] mwifiex_del_virtual_intf+0xc8/0x188 [mwifiex]
[ 247.214174] mwifiex_uninit_sw+0x158/0x1b0 [mwifiex]
[ 247.219747] mwifiex_remove_card+0x38/0xa0 [mwifiex]
[ 247.225316] mwifiex_pcie_remove+0xd0/0xe0 [mwifiex_pcie]
[ 247.231451] pci_device_remove+0x50/0xe0
[ 247.235849] device_release_driver_internal+0x110/0x1b0
[ 247.241701] driver_detach+0x5c/0x9c
[ 247.245704] bus_remove_driver+0x84/0xb8
[ 247.250095] driver_unregister+0x3c/0x60
[ 247.254486] pci_unregister_driver+0x2c/0x90
[ 247.259267] cleanup_module+0x18/0xcdc [mwifiex_pcie]
Fixes: a05829a722 ("cfg80211: avoid holding the RTNL when calling the driver")
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/linux-wireless/98392296-40ee-6300-369c-32e16cff3725@gmail.com/
Link: https://lore.kernel.org/linux-wireless/ab4d00ce52f32bd8e45ad0448a44737e@bewaar.me/
Reported-by: Maximilian Luz <luzmaximilian@gmail.com>
Reported-by: dave@bewaar.me
Cc: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Brian Norris <briannorris@chromium.org>
Tested-by: Maximilian Luz <luzmaximilian@gmail.com>
Tested-by: Dave Olsthoorn <dave@bewaar.me>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210515024227.2159311-1-briannorris@chromium.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f6eb84fa59 upstream.
The driver_name="tegra" is now required by the newer ALSA UCMs, otherwise
Tegra UCMs don't match by the path/name.
All Tegra machine drivers are specifying the card's name, but it has no
effect if model name is specified in the device-tree since it overrides
the card's name. We need to set the driver_name to "tegra" in order to
get a usable lookup path for the updated ALSA UCMs. The new UCM lookup
path has a form of driver_name/card_name.
The old lookup paths that are based on driver module name continue to
work as before. Note that UCM matching never worked for Tegra ASoC drivers
if they were compiled as built-in, this is fixed by supporting the new
naming scheme.
Cc: stable@vger.kernel.org
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Link: https://lore.kernel.org/r/20210529154649.25936-2-digetx@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d9ec9daa20 upstream.
The stratix10-soc driver uses fpga_mgr_create() function and is therefore
responsible to call fpga_mgr_free() to release the class driver resources.
Add a missing call to fpga_mgr_free in the s10_remove() function.
Signed-off-by: Russ Weight <russell.h.weight@intel.com>
Reviewed-by: Xu Yilun <yilun.xu@intel.com>
Signed-off-by: Moritz Fischer <mdf@kernel.org>
Fixes: e7eef1d763 ("fpga: add intel stratix10 soc fpga manager driver")
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20210614170909.232415-3-mdf@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8b33dfe0ba upstream.
Bad counter reads are experienced sometimes when bit 10 or greater rolls
over. Originally, testing showed that at least 10 lower bits would be
set to the same value during these bad reads. However, some users still
reported time skips.
Wider testing revealed that on some chips, occasionally only the lowest
9 bits would read as the anomalous value. During these reads (which
still happen only when bit 10), bit 9 would read as the correct value.
Reduce the mask by one bit to cover these cases as well.
Cc: stable@vger.kernel.org
Fixes: c950ca8c35 ("clocksource/drivers/arch_timer: Workaround for Allwinner A64 timer instability")
Reported-by: Roman Stratiienko <r.stratiienko@gmail.com>
Signed-off-by: Samuel Holland <samuel@sholland.org>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20210515021439.55316-1-samuel@sholland.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b22afcdf04 upstream.
Alexey and Joshua tried to solve a cpusets related hotplug problem which is
user space visible and results in unexpected behaviour for some time after
a CPU has been plugged in and the corresponding uevent was delivered.
cpusets delegate the hotplug work (rebuilding cpumasks etc.) to a
workqueue. This is done because the cpusets code has already a lock
nesting of cgroups_mutex -> cpu_hotplug_lock. A synchronous callback or
waiting for the work to finish with cpu_hotplug_lock held can and will
deadlock because that results in the reverse lock order.
As a consequence the uevent can be delivered before cpusets have consistent
state which means that a user space invocation of sched_setaffinity() to
move a task to the plugged CPU fails up to the point where the scheduled
work has been processed.
The same is true for CPU unplug, but that does not create user observable
failure (yet).
It's still inconsistent to claim that an operation is finished before it
actually is and that's the real issue at hand. uevents just make it
reliably observable.
Obviously the problem should be fixed in cpusets/cgroups, but untangling
that is pretty much impossible because according to the changelog of the
commit which introduced this 8 years ago:
3a5a6d0c2b03("cpuset: don't nest cgroup_mutex inside get_online_cpus()")
the lock order cgroups_mutex -> cpu_hotplug_lock is a design decision and
the whole code is built around that.
So bite the bullet and invoke the relevant cpuset function, which waits for
the work to finish, in _cpu_up/down() after dropping cpu_hotplug_lock and
only when tasks are not frozen by suspend/hibernate because that would
obviously wait forever.
Waiting there with cpu_add_remove_lock, which is protecting the present
and possible CPU maps, held is not a problem at all because neither work
queues nor cpusets/cgroups have any lockchains related to that lock.
Waiting in the hotplug machinery is not problematic either because there
are already state callbacks which wait for hardware queues to drain. It
makes the operations slightly slower, but hotplug is slow anyway.
This ensures that state is consistent before returning from a hotplug
up/down operation. It's still inconsistent during the operation, but that's
a different story.
Add a large comment which explains why this is done and why this is not a
dump ground for the hack of the day to work around half thought out locking
schemes. Document also the implications vs. hotplug operations and
serialization or the lack of it.
Thanks to Alexy and Joshua for analyzing why this temporary
sched_setaffinity() failure happened.
Fixes: 3a5a6d0c2b03("cpuset: don't nest cgroup_mutex inside get_online_cpus()")
Reported-by: Alexey Klimov <aklimov@redhat.com>
Reported-by: Joshua Baker <jobaker@redhat.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Alexey Klimov <aklimov@redhat.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/87tuowcnv3.ffs@nanos.tec.linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 52218fcd61 upstream.
The TTL field indicates the level of page table walk holding the *leaf*
entry for the address being invalidated. But currently, the TTL field
may be set to an incorrent value in the following stack:
pte_free_tlb
__pte_free_tlb
tlb_remove_table
tlb_table_invalidate
tlb_flush_mmu_tlbonly
tlb_flush
In this case, we just want to flush a PTE page, but the tlb->cleared_pmds
is set and we get tlb_level = 2 in the tlb_get_level() function. This may
cause some unexpected problems.
This patch set the TTL field to 0 if tlb->freed_tables is set. The
tlb->freed_tables indicates page table pages are freed, not the leaf
entry.
Cc: <stable@vger.kernel.org> # 5.9.x
Fixes: c4ab2cbc1d ("arm64: tlb: Set the TTL field in flush_tlb_range")
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Reported-by: ZhuRui <zhurui3@huawei.com>
Signed-off-by: Zhenyu Ye <yezhenyu2@huawei.com>
Link: https://lore.kernel.org/r/b80ead47-1f88-3a00-18e1-cacc22f54cc4@huawei.com
Signed-off-by: Will Deacon <will@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f6bca4d91b upstream.
DIPM is unsupported or broken on sunxi. Trying to enable the power
management policy med_power_with_dipm on an Allwinner A20 SoC based board
leads to immediate I/O errors and the attached SATA disk disappears from
the /dev filesystem. A reset (power cycle) is required to make the SATA
controller or disk work again. The A10 and A20 SoC data sheets and manuals
don't mention DIPM at all [1], so it's fair to assume that it's simply not
supported. But even if it was, it should be considered broken and best be
disabled in the ahci_sunxi driver.
[1] https://github.com/allwinner-zh/documents/tree/master/
Fixes: c5754b5220 ("ARM: sunxi: Add support for Allwinner SUNXi SoCs sata to ahci_platform")
Cc: stable@vger.kernel.org
Signed-off-by: Timo Sigurdsson <public_timo.s@silentcreek.de>
Tested-by: Timo Sigurdsson <public_timo.s@silentcreek.de>
Link: https://lore.kernel.org/r/20210614072539.3307-1-public_timo.s@silentcreek.de
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 222a28edce upstream.
Fix think-o about which variable to find the Kbuild-configured shell.
This has accidentally worked due to most shells setting $SHELL by
default.
Fixes: 51e46c7a40 ("docs, parallelism: Rearrange how jobserver reservations are made")
Cc: stable@vger.kernel.org
Signed-off-by: Kees Cook <keescook@chromium.org>
Link: https://lore.kernel.org/r/20210617225808.3907377-1-keescook@chromium.org
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 09247e110b upstream.
While initializing an UHS-I SD card, the mmc core first tries to switch to
1.8V I/O voltage, before it continues to change the settings for the bus
speed mode.
However, the current behaviour in the mmc core is inconsistent and doesn't
conform to the SD spec. More precisely, an SD card that supports UHS-I must
set both the SD_OCR_CCS bit and the SD_OCR_S18R bit in the OCR register
response. When switching to 1.8V I/O the mmc core correctly checks both of
the bits, but only the SD_OCR_S18R bit when changing the settings for bus
speed mode.
Rather than actually fixing the code to confirm to the SD spec, let's
deliberately deviate from it by requiring only the SD_OCR_S18R bit for both
parts. This enables us to support UHS-I for SDSC cards (outside spec),
which is actually being supported by some existing SDSC cards. Moreover,
this fixes the inconsistent behaviour.
Signed-off-by: Christian Loehle <cloehle@hyperstone.com>
Link: https://lore.kernel.org/r/CWXP265MB26803AE79E0AD5ED083BF2A6C4529@CWXP265MB2680.GBRP265.PROD.OUTLOOK.COM
Cc: stable@vger.kernel.org
[Ulf: Rewrote commit message and comments to clarify the changes]
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 77347eda64 upstream.
It might be that something goes wrong during tuning so the MMC core will
immediately trigger a retune. In our case it was:
- we sent a tuning block
- there was an error so we need to send an abort cmd to the eMMC
- the abort cmd had a CRC error
- retune was set by the MMC core
This lead to a vicious circle causing a performance regression of 75%.
So, clear retuning flags before we enable retuning to start with a known
cleared state.
Reported-by Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Suggested-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Tested-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Fixes: bd11e8bd03 ("mmc: core: Flag re-tuning is needed on CRC errors")
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20210624151616.38770-2-wsa+renesas@sang-engineering.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d0244847f9 upstream.
When an eMMC device is being run in HS400 mode, any access to the
RPMB device will cause the error message "mmc1: Invalid UHS-I mode
selected". This happens as a result of tuning being disabled before
RPMB access and then re-enabled after the RPMB access is complete.
When tuning is re-enabled, the system has to switch from HS400
to HS200 to do the tuning and then back to HS400. As part of
sequence to switch from HS400 to HS200 the system is temporarily
put into HS mode. When switching to HS mode, sdhci_get_preset_value()
is called and does not have support for HS mode and prints the warning
message and returns the preset for SDR12. The fix is to add support
for MMC and SD HS modes to sdhci_get_preset_value().
This can be reproduced on any system running eMMC in HS400 mode
(not HS400ES) by using the "mmc" utility to run the following
command: "mmc rpmb read-counter /dev/mmcblk0rpmb".
Signed-off-by: Al Cooper <alcooperx@gmail.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Fixes: 52983382c7 ("mmc: sdhci: enhance preset value function")
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20210624163045.33651-1-alcooperx@gmail.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 94ee6782e0 upstream.
On the Toshiba Encore 2 WT8-B the microSD slot always reports the card
being write-protected even though microSD cards do not have a write-protect
switch at all.
Add a new DMI_QUIRK_SD_NO_WRITE_PROTECT quirk entry to sdhci-acpi.c's
DMI quirk table for this.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/20210503092157.5689-1-hdegoede@redhat.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Cc: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 07b72960d2 upstream.
intel_dp_vsc_sdp_unpack() was using a memset() size (36, struct dp_sdp)
larger than the destination (24, struct drm_dp_vsc_sdp), clobbering
fields in struct intel_crtc_state after infoframes.vsc. Use the actual
target size for the memset().
Fixes: 1b404b7dbb ("drm/i915/dp: Read out DP SDPs")
Cc: stable@vger.kernel.org
Signed-off-by: Kees Cook <keescook@chromium.org>
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210617213301.1824728-1-keescook@chromium.org
(cherry picked from commit c88e2647c5)
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 68b433fe69 upstream.
It should have been an OVERLAY from the beginning. The documentation
stipulates that there should be an unique PRIMARY plane per CRTC.
Fixes: fc1acf317b ("drm/ingenic: Add support for the IPU")
Cc: <stable@vger.kernel.org> # 5.8+
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Acked-by: Simon Ser <contact@emersion.fr>
Link: https://patchwork.freedesktop.org/patch/msgid/20210329175046.214629-2-paul@crapouillou.net
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit cee93c0282 upstream.
Since
commit 890880ddfd
Author: Paul Kocialkowski <paul.kocialkowski@bootlin.com>
Date: Fri Jan 4 09:56:10 2019 +0100
drm: Auto-set allow_fb_modifiers when given modifiers at plane init
this is done automatically as part of plane init, if drivers set the
modifier list correctly. Which is the case here.
Note that this fixes an inconsistency: We've set the cap everywhere,
but only nv50+ supports modifiers. Hence cc stable, but not further
back then the patch from Paul.
Reviewed-by: Lyude Paul <lyude@redhat.com>
Cc: stable@vger.kernel.org # v5.1 +
Cc: Pekka Paalanen <pekka.paalanen@collabora.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Cc: Ben Skeggs <bskeggs@redhat.com>
Cc: nouveau@lists.freedesktop.org
Link: https://patchwork.freedesktop.org/patch/msgid/20210427092018.832258-6-daniel.vetter@ffwll.ch
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 26c3e7fd5a upstream.
Even when all we support is linear, make that explicit. Otherwise the
uapi is rather confusing.
Acked-by: Liviu Dudau <liviu.dudau@arm.com>
Acked-by: Pekka Paalanen <pekka.paalanen@collabora.com>
Reviewed-by: Lyude Paul <lyude@redhat.com>
Cc: stable@vger.kernel.org
Cc: Pekka Paalanen <pekka.paalanen@collabora.com>
Cc: Liviu Dudau <liviu.dudau@arm.com>
Cc: Brian Starkey <brian.starkey@arm.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210427092018.832258-2-daniel.vetter@ffwll.ch
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 35cbb8c91e upstream.
Setting the cap without the modifier list is very confusing to
userspace. Fix that by listing the ones we support explicitly.
Stable backport so that userspace can rely on this working in a
reasonable way, i.e. that the cap set implies IN_FORMATS is available.
Acked-by: Pekka Paalanen <pekka.paalanen@collabora.com>
Reviewed-by: Lyude Paul <lyude@redhat.com>
Cc: stable@vger.kernel.org
Cc: Pekka Paalanen <pekka.paalanen@collabora.com>
Cc: Rob Clark <robdclark@chromium.org>
Cc: Jordan Crouse <jordan@cosmicpenguin.net>
Cc: Emil Velikov <emil.velikov@collabora.com>
Cc: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210427092018.832258-5-daniel.vetter@ffwll.ch
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit be4306ad92 upstream.
Since
commit 890880ddfd
Author: Paul Kocialkowski <paul.kocialkowski@bootlin.com>
Date: Fri Jan 4 09:56:10 2019 +0100
drm: Auto-set allow_fb_modifiers when given modifiers at plane init
this is done automatically as part of plane init, if drivers set the
modifier list correctly. Which is the case here.
It was slightly inconsistently though, since planes with only linear
modifier support haven't listed that explicitly. Fix that, and cc:
stable to allow userspace to rely on this. Again don't backport
further than where Paul's patch got added.
Cc: stable@vger.kernel.org # v5.1 +
Cc: Pekka Paalanen <pekka.paalanen@collabora.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: Jonathan Hunter <jonathanh@nvidia.com>
Cc: linux-tegra@vger.kernel.org
Link: https://patchwork.freedesktop.org/patch/msgid/20210413094904.3736372-10-daniel.vetter@ffwll.ch
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 60a6b73dd8 upstream.
When using a 24-bit panel on a 8-bit serial bus, the pixel clock
requested by the panel has to be multiplied by 3, since the subpixels
are shifted sequentially.
The code (in ingenic_drm_encoder_atomic_check) already computed
crtc_state->adjusted_mode->crtc_clock accordingly, but clk_set_rate()
used crtc_state->adjusted_mode->clock instead.
Fixes: 28ab7d35b6 ("drm/ingenic: Properly compute timings when using a 3x8-bit panel")
Cc: stable@vger.kernel.org # v5.10
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Tested-by: H. Nikolaus Schaller <hns@goldelico.com> # CI20/jz4780 (HDMI) and Alpha400/jz4730 (LCD)
Acked-by: Thomas Zimmermann <tzimmermann@suse.de>
Link: https://patchwork.freedesktop.org/patch/msgid/20210323144008.166248-1-paul@crapouillou.net
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c6c6a71219 upstream.
[Why]
This hasn't been well tested and leads to complete system hangs on DCN1
based systems, possibly others.
The system hang can be reproduced by gesturing the video on the YouTube
Android app on ChromeOS into full screen.
[How]
Reject atomic commits with non-zero drm_plane_state.src_x or src_y values.
v2:
- Add code comment describing the reason we're rejecting non-zero
src_x and src_y
- Drop gerrit Change-Id
- Add stable CC
- Based on amd-staging-drm-next
v3: removed trailing whitespace
Signed-off-by: Harry Wentland <harry.wentland@amd.com>
Cc: stable@vger.kernel.org
Cc: nicholas.kazlauskas@amd.com
Cc: amd-gfx@lists.freedesktop.org
Cc: alexander.deucher@amd.com
Cc: Roman.Li@amd.com
Cc: hersenxs.wu@amd.com
Cc: danny.wang@amd.com
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Acked-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Hersen Wu <hersenxs.wu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1ca46d3e43 upstream.
Add device HID AMDI0031 to the AMD GPIO controller driver match table.
This controller can be found on Microsoft Surface Laptop 4 devices and
seems similar enough that we can just copy the existing AMDI0030 entry.
Cc: <stable@vger.kernel.org> # 5.10+
Tested-by: Sachi King <nakato@nakato.io>
Signed-off-by: Maximilian Luz <luzmaximilian@gmail.com>
Link: https://lore.kernel.org/r/20210512210316.1982416-1-luzmaximilian@gmail.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b354498bbe upstream.
commit cf6d100dd2 ("drm/rockchip: dsi: add dual mipi support") added
this devcnt field and call to component_del(). However, these both
appear to be erroneous changes left over from an earlier version of the
patch. In the version merged, nothing ever modifies devcnt, meaning
component_del() runs unconditionally and in addition to the
component_del() calls in dw_mipi_dsi_rockchip_host_detach(). The second
call fails to delete anything and produces a warning in dmesg.
If we look at the previous version of the patch[1], however, we see that
it had logic to calculate devcnt and call component_add() in certain
situations. This was removed in v6, and the fact that the deletion code
was not appears to have been an oversight.
[1] https://patchwork.kernel.org/project/dri-devel/patch/20180821140515.22246-8-heiko@sntech.de/
Fixes: cf6d100dd2 ("drm/rockchip: dsi: add dual mipi support")
Cc: stable@vger.kernel.org
Signed-off-by: Thomas Hebb <tommyhebb@gmail.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Link: https://patchwork.freedesktop.org/patch/msgid/201385acb0eeb5dfb037afdc6a94bfbcdab97f99.1618797778.git.tommyhebb@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 205bb69a90 upstream.
While the DP specification isn't entirely clear on if this should be
allowed or not, some branch devices report having downstream ports present
while also reporting a downstream port count of 0. So to avoid breaking
those devices, we need to handle this in drm_dp_read_downstream_info().
So, to do this we assume there's no downstream port info when the
downstream port count is 0.
Signed-off-by: Lyude Paul <lyude@redhat.com>
Tested-by: Jérôme de Bretagne <jerome.debretagne@gmail.com>
Bugzilla: https://gitlab.freedesktop.org/drm/intel/-/issues/3416
Fixes: 3d3721ccb1 ("drm/i915/dp: Extract drm_dp_read_downstream_info()")
Cc: <stable@vger.kernel.org> # v5.10+
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210430223428.10514-1-lyude@redhat.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5b00600042 upstream.
Since we fixed the hooks to disable the encoder at boot, we now have an
unbalanced clk_disable call at boot since we never enabled them in the
first place.
Let's mimic the state of the hardware and enable the clocks at boot if
the controller is enabled to get the use-count right.
Cc: <stable@vger.kernel.org> # v5.10+
Fixes: 09c438139b ("drm/vc4: hdmi: Implement finer-grained hooks")
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Reviewed-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210507150515.257424-7-maxime@cerno.tech
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 47a5074303 upstream.
The vc4_set_crtc_possible_masks is meant to run over all the encoders
and then set their possible_crtcs mask to their associated pixelvalve.
However, since the commit 39fcb28083 ("drm/vc4: txp: Turn the TXP into
a CRTC of its own"), the TXP has been turned to a CRTC and encoder of
its own, and while it does indeed register an encoder, it no longer has
an associated pixelvalve. The code will thus run over the TXP encoder
and set a bogus possible_crtcs mask, overriding the one set in the TXP
bind function.
In order to fix this, let's skip any virtual encoder.
Cc: <stable@vger.kernel.org> # v5.9+
Fixes: 39fcb28083 ("drm/vc4: txp: Turn the TXP into a CRTC of its own")
Acked-by: Thomas Zimmermann <tzimmermann@suse.de>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://patchwork.freedesktop.org/patch/msgid/20210507150515.257424-3-maxime@cerno.tech
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit bf6de8e615 upstream.
The current code does a binary OR on the possible_crtcs variable of the
TXP encoder, while we want to set it to that value instead.
Cc: <stable@vger.kernel.org> # v5.9+
Fixes: 39fcb28083 ("drm/vc4: txp: Turn the TXP into a CRTC of its own")
Acked-by: Thomas Zimmermann <tzimmermann@suse.de>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://patchwork.freedesktop.org/patch/msgid/20210507150515.257424-2-maxime@cerno.tech
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c1bfd74bfe upstream.
On the Loongson64 platform used with Radeon GPU, shutdown or reboot failed
when console=tty is in the boot cmdline.
radeon_suspend_kms() puts the hw in the suspend state, especially set fb
state as FBINFO_STATE_SUSPENDED:
if (fbcon) {
console_lock();
radeon_fbdev_set_suspend(rdev, 1);
console_unlock();
}
Then avoid to do any more fb operations in the related functions:
if (p->state != FBINFO_STATE_RUNNING)
return;
So call radeon_suspend_kms() in radeon_pci_shutdown() for Loongson64 to fix
this issue, it looks like some kind of workaround like powerpc.
Co-developed-by: Jianmin Lv <lvjianmin@loongson.cn>
Signed-off-by: Jianmin Lv <lvjianmin@loongson.cn>
Signed-off-by: Tiezhu Yang <yangtiezhu@loongson.cn>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9ba85914c3 upstream.
radeon_user_framebuffer_create() misses to call drm_gem_object_put() in
an error path. Add the missed function call to fix it.
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Jing Xiangfeng <jingxiangfeng@huawei.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit adcf949e66 upstream.
SMU had set all the necessary fields for a link width switch
but the width switch wasn't occurring because the link was idle
in the L1 state. Setting LC_L1_RECONFIG_EN=0x1 will allow width
switches to also be initiated while in L1 instead of waiting until
the link is back in L0.
Signed-off-by: Evan Quan <evan.quan@amd.com>
Reviewed-by: Lijo Lazar <lijo.lazar@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5a5da8ae95 upstream.
A lot of NAK-G being generated when link widht switching is happening.
WA for this issue is to program the SPC to 4 symbols per clock during
bootup when the native PCIE width is x4.
Signed-off-by: Evan Quan <evan.quan@amd.com>
Reviewed-by: Lijo Lazar <lijo.lazar@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e2329e74a6 upstream.
Without driver loaded, SDMA0_UTCL1_PAGE.TMZ_ENABLE is set to 1
by default for all asic. On Raven/Renoir, the sdma goldsetting
changes SDMA0_UTCL1_PAGE.TMZ_ENABLE to 0.
This patch restores SDMA0_UTCL1_PAGE.TMZ_ENABLE to 1.
Signed-off-by: Aaron Liu <aaron.liu@amd.com>
Acked-by: Luben Tuikov <luben.tuikov@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit aa61581126 upstream.
Navi series GPUs have 2 SIMDs per CU (and then 2 CUs per WGP).
The NV enum headers incorrectly listed this as 4, which later meant
we were incorrectly reporting the number of SIMDs in the HSA
topology. This could cause problems down the line for user-space
applications that want to launch a fixed amount of work to each
SIMD.
Signed-off-by: Joseph Greathouse <Joseph.Greathouse@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Felix Kuehling <Felix.Kuehling@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 91cdbb955a upstream.
The kernel handles the NX fault by updating CSB or sending
signal to process. In multithread applications, children can
open VAS windows and can exit without closing them. But the
parent can continue to send NX requests with these windows. To
prevent pid reuse, reference will be taken on pid and tgid
when the window is opened and release them during window close.
The current code is not releasing the tgid reference which can
cause pid leak and this patch fixes the issue.
Fixes: db1c08a740 ("powerpc/vas: Take reference to PID and mm for user space windows")
Cc: stable@vger.kernel.org # 5.8+
Reported-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Haren Myneni <haren@linux.ibm.com>
Reviewed-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/6020fc4d444864fe20f7dcdc5edfe53e67480a1c.camel@linux.ibm.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 015d98149b upstream.
A change in clang 13 results in the __lwsync macro being defined as
__builtin_ppc_lwsync, which emits 'lwsync' or 'msync' depending on what
the target supports. This breaks the build because of -Werror in
arch/powerpc, along with thousands of warnings:
In file included from arch/powerpc/kernel/pmc.c:12:
In file included from include/linux/bug.h:5:
In file included from arch/powerpc/include/asm/bug.h:109:
In file included from include/asm-generic/bug.h:20:
In file included from include/linux/kernel.h:12:
In file included from include/linux/bitops.h:32:
In file included from arch/powerpc/include/asm/bitops.h:62:
arch/powerpc/include/asm/barrier.h:49:9: error: '__lwsync' macro redefined [-Werror,-Wmacro-redefined]
#define __lwsync() __asm__ __volatile__ (stringify_in_c(LWSYNC) : : :"memory")
^
<built-in>:308:9: note: previous definition is here
#define __lwsync __builtin_ppc_lwsync
^
1 error generated.
Undefine this macro so that the runtime patching introduced by
commit 2d1b202762 ("powerpc: Fixup lwsync at runtime") continues to
work properly with clang and the build no longer breaks.
Cc: stable@vger.kernel.org
Signed-off-by: Nathan Chancellor <nathan@kernel.org>
Reviewed-by: Nick Desaulniers <ndesaulniers@google.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://github.com/ClangBuiltLinux/linux/issues/1386
Link: 62b5df7fe2
Link: https://lore.kernel.org/r/20210528182752.1852002-1-nathan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3f601608b7 upstream.
This is a smatch warning:
arch/powerpc/sysdev/xive/common.c:1161 xive_request_ipi() warn: unsigned 'xid->irq' is never less than zero.
Fixes: fd6db2892e ("powerpc/xive: Modernize XIVE-IPI domain with an 'alloc' handler")
Cc: stable@vger.kernel.org # v5.13
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20210701152412.1507612-1-clg@kaod.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 307e5042c7 upstream.
Commit 91c960b005 ("bpf: Rename BPF_XADD and prepare to encode other
atomics in .imm") converted BPF_XADD to BPF_ATOMIC and updated all JIT
implementations to reject JIT'ing instructions with an immediate value
different from BPF_ADD. However, ppc32 BPF JIT was implemented around
the same time and didn't include the same change. Update the ppc32 JIT
accordingly.
Fixes: 51c66ad849 ("powerpc/bpf: Implement extended BPF on PPC32")
Cc: stable@vger.kernel.org # v5.13+
Signed-off-by: Naveen N. Rao <naveen.n.rao@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/426699046d89fe50f66ecf74bd31c01eda976ba5.1625145429.git.naveen.n.rao@linux.vnet.ibm.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit cd5d5e602f upstream.
The powerpc kernel is not prepared to handle exec faults from kernel.
Especially, the function is_exec_fault() will return 'false' when an
exec fault is taken by kernel, because the check is based on reading
current->thread.regs->trap which contains the trap from user.
For instance, when provoking a LKDTM EXEC_USERSPACE test,
current->thread.regs->trap is set to SYSCALL trap (0xc00), and
the fault taken by the kernel is not seen as an exec fault by
set_access_flags_filter().
Commit d7df2443cd ("powerpc/mm: Fix spurious segfaults on radix
with autonuma") made it clear and handled it properly. But later on
commit d3ca587404 ("powerpc/mm: Fix reporting of kernel execute
faults") removed that handling, introducing test based on error_code.
And here is the problem, because on the 603 all upper bits of SRR1
get cleared when the TLB instruction miss handler bails out to ISI.
Until commit cbd7e6ca02 ("powerpc/fault: Avoid heavy
search_exception_tables() verification"), an exec fault from kernel
at a userspace address was indirectly caught by the lack of entry for
that address in the exception tables. But after that commit the
kernel mainly relies on KUAP or on core mm handling to catch wrong
user accesses. Here the access is not wrong, so mm handles it.
It is a minor fault because PAGE_EXEC is not set,
set_access_flags_filter() should set PAGE_EXEC and voila.
But as is_exec_fault() returns false as explained in the beginning,
set_access_flags_filter() bails out without setting PAGE_EXEC flag,
which leads to a forever minor exec fault.
As the kernel is not prepared to handle such exec faults, the thing to
do is to fire in bad_kernel_fault() for any exec fault taken by the
kernel, as it was prior to commit d3ca587404.
Fixes: d3ca587404 ("powerpc/mm: Fix reporting of kernel execute faults")
Cc: stable@vger.kernel.org # v4.14+
Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Acked-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/024bb05105050f704743a0083fe3548702be5706.1625138205.git.christophe.leroy@csgroup.eu
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 97113eb39f upstream.
To avoid a race between rmap walk and mremap, mremap does
take_rmap_locks(). The lock was taken to ensure that rmap walk don't miss
a page table entry due to PTE moves via move_pagetables(). The kernel
does further optimization of this lock such that if we are going to find
the newly added vma after the old vma, the rmap lock is not taken. This
is because rmap walk would find the vmas in the same order and if we don't
find the page table attached to older vma we would find it with the new
vma which we would iterate later.
As explained in commit eb66ae0308 ("mremap: properly flush TLB before
releasing the page") mremap is special in that it doesn't take ownership
of the page. The optimized version for PUD/PMD aligned mremap also
doesn't hold the ptl lock. This can result in stale TLB entries as show
below.
This patch updates the rmap locking requirement in mremap to handle the race condition
explained below with optimized mremap::
Optmized PMD move
CPU 1 CPU 2 CPU 3
mremap(old_addr, new_addr) page_shrinker/try_to_unmap_one
mmap_write_lock_killable()
addr = old_addr
lock(pte_ptl)
lock(pmd_ptl)
pmd = *old_pmd
pmd_clear(old_pmd)
flush_tlb_range(old_addr)
*new_pmd = pmd
*new_addr = 10; and fills
TLB with new addr
and old pfn
unlock(pmd_ptl)
ptep_clear_flush()
old pfn is free.
Stale TLB entry
Optimized PUD move also suffers from a similar race. Both the above race
condition can be fixed if we force mremap path to take rmap lock.
Link: https://lkml.kernel.org/r/20210616045239.370802-7-aneesh.kumar@linux.ibm.com
Fixes: 2c91bd4a4e ("mm: speed up mremap by 20x on large regions")
Fixes: c49dd34018 ("mm: speedup mremap on 1GB or larger regions")
Link: https://lore.kernel.org/linux-mm/CAHk-=wgXVR04eBNtxQfevontWnP6FDm+oj5vauQXP3S-huwbPw@mail.gmail.com
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.ibm.com>
Acked-by: Hugh Dickins <hughd@google.com>
Acked-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Cc: Christophe Leroy <christophe.leroy@csgroup.eu>
Cc: Joel Fernandes <joel@joelfernandes.org>
Cc: Kalesh Singh <kaleshsingh@google.com>
Cc: Kirill A. Shutemov <kirill@shutemov.name>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Nicholas Piggin <npiggin@gmail.com>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit cad065ed8d upstream.
MIPS MT extensions were added with the MIPS 34K processor, which was
based on the MIPS32r2 ISA.
This fixes a build error when building a generic kernel for a MIPS32r1
CPU.
Fixes: c434b9f80b ("MIPS: Kconfig: add MIPS_GENERIC_KERNEL symbol")
Cc: stable@vger.kernel.org # v5.9
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c4bf1f25c6 upstream.
Commit 275e88b06a ("PCI: tegra: Fix host link initialization") broke
host initialization during resume as it misses out calling the API
dw_pcie_setup_rc() which is required for host and MSI initialization.
Link: https://lore.kernel.org/r/20210504172157.29712-1-vidyas@nvidia.com
Fixes: 275e88b06a ("PCI: tegra: Fix host link initialization")
Tested-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Vidya Sagar <vidyas@nvidia.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 23c64447b3 ]
The original clock (3 MHz) is too fast for the clocksource,
there will be a chance that the system may get stuck.
Reported-by: Nikolaus Schaller <hns@goldelico.com>
Tested-by: Nikolaus Schaller <hns@goldelico.com> # on CI20
Signed-off-by: 周琰杰 (Zhou Yanjie) <zhouyanjie@wanyeetech.com>
Acked-by: Paul Cercueil <paul@crapouillou.net>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c994a3ec7e ]
Clang's integrated assembler only accepts these instructions when the
cpu is set to mips32r5. With this change, we can assemble
malta_defconfig with Clang via `make LLVM_IAS=1`.
Link: https://github.com/ClangBuiltLinux/linux/issues/763
Reported-by: Dmitry Golovin <dima@golovin.in>
Signed-off-by: Nick Desaulniers <ndesaulniers@google.com>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6817c94443 ]
The cause of the problem is as follows:
1. when cat /sys/devices/system/memory/memory0/valid_zones,
test_pages_in_a_zone() will be called.
2. test_pages_in_a_zone() finds the zone according to stat_pfn = 0.
The smallest pfn of the numa node in the mips architecture is 128,
and the page corresponding to the previous 0~127 pfn is not
initialized (page->flags is 0xFFFFFFFF)
3. The nid and zonenum obtained using page_zone(pfn_to_page(0)) are out
of bounds in the corresponding array,
&NODE_DATA(page_to_nid(page))->node_zones[page_zonenum(page)],
access to the out-of-bounds zone member variables appear abnormal,
resulting in Oops.
Therefore, it is necessary to keep the page between 0 and the minimum
pfn to prevent Oops from appearing.
Signed-off-by: zhanglianjie <zhanglianjie@uniontech.com>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 50619dbf8d ]
The first chunk in a packet is ensured to be present at the beginning of
sctp_rcv(), as a packet needs to have at least 1 chunk. But the second
one, may not be completely available and ch->length can be over
uninitialized memory.
Fix here is by only trying to walk on the next chunk if there is enough to
hold at least the header, and then proceed with the ch->length validation
that is already there.
Reported-by: Ilja Van Sprundel <ivansprundel@ioactive.com>
Signed-off-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
