commit 316294bb66 upstream.
Reading the hardware registers of the &slimbam on RB3 reveals that the BAM
supports only 23 pipes (channels) and supports 4 EEs instead of 2. This
hasn't caused problems so far since nothing is using the extra channels,
but attempting to use them would lead to crashes.
The bam_dma driver might warn in the future if the num-channels in the DT
are wrong, so correct the properties in the DT to avoid future regressions.
Cc: stable@vger.kernel.org
Fixes: 27ca1de07d ("arm64: dts: qcom: sdm845: add slimbus nodes")
Signed-off-by: Stephan Gerhold <stephan.gerhold@linaro.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20250821-sdm845-slimbam-channels-v1-1-498f7d46b9ee@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f73c82c855 upstream.
On most MSM8939 devices, the bootloader already initializes the display to
show the boot splash screen. In this situation, MDSS is already configured
and left running when starting Linux. To avoid side effects from the
bootloader configuration, the MDSS reset can be specified in the device
tree to start again with a clean hardware state.
The reset for MDSS is currently missing in msm8939.dtsi, which causes
errors when the MDSS driver tries to re-initialize the registers:
dsi_err_worker: status=6
dsi_err_worker: status=6
dsi_err_worker: status=6
...
It turns out that we have always indirectly worked around this by building
the MDSS driver as a module. Before v6.17, the power domain was temporarily
turned off until the module was loaded, long enough to clear the register
contents. In v6.17, power domains are not turned off during boot until
sync_state() happens, so this is no longer working. Even before v6.17 this
resulted in broken behavior, but notably only when the MDSS driver was
built-in instead of a module.
Cc: stable@vger.kernel.org
Fixes: 61550c6c15 ("arm64: dts: qcom: Add msm8939 SoC")
Signed-off-by: Stephan Gerhold <stephan.gerhold@linaro.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20250915-msm8916-resets-v1-2-a5c705df0c45@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 99b78773c2 upstream.
On most MSM8916 devices (aside from the DragonBoard 410c), the bootloader
already initializes the display to show the boot splash screen. In this
situation, MDSS is already configured and left running when starting Linux.
To avoid side effects from the bootloader configuration, the MDSS reset can
be specified in the device tree to start again with a clean hardware state.
The reset for MDSS is currently missing in msm8916.dtsi, which causes
errors when the MDSS driver tries to re-initialize the registers:
dsi_err_worker: status=6
dsi_err_worker: status=6
dsi_err_worker: status=6
...
It turns out that we have always indirectly worked around this by building
the MDSS driver as a module. Before v6.17, the power domain was temporarily
turned off until the module was loaded, long enough to clear the register
contents. In v6.17, power domains are not turned off during boot until
sync_state() happens, so this is no longer working. Even before v6.17 this
resulted in broken behavior, but notably only when the MDSS driver was
built-in instead of a module.
Cc: stable@vger.kernel.org
Fixes: 305410ffd1 ("arm64: dts: msm8916: Add display support")
Signed-off-by: Stephan Gerhold <stephan.gerhold@linaro.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20250915-msm8916-resets-v1-1-a5c705df0c45@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 399dbcadc0 upstream.
There is no synchronization between different code paths in the ACPI
battery driver that update its sysfs interface or its power supply
class device interface. In some cases this results to functional
failures due to race conditions.
One example of this is when two ACPI notifications:
- ACPI_BATTERY_NOTIFY_STATUS (0x80)
- ACPI_BATTERY_NOTIFY_INFO (0x81)
are triggered (by the platform firmware) in a row with a little delay
in between after removing and reinserting a laptop battery. Both
notifications cause acpi_battery_update() to be called and if the delay
between them is sufficiently small, sysfs_add_battery() can be re-entered
before battery->bat is set which leads to a duplicate sysfs entry error:
sysfs: cannot create duplicate filename '/devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0A:00/power_supply/BAT1'
CPU: 1 UID: 0 PID: 185 Comm: kworker/1:4 Kdump: loaded Not tainted 6.12.38+deb13-amd64 #1 Debian 6.12.38-1
Hardware name: Gateway NV44 /SJV40-MV , BIOS V1.3121 04/08/2009
Workqueue: kacpi_notify acpi_os_execute_deferred
Call Trace:
<TASK>
dump_stack_lvl+0x5d/0x80
sysfs_warn_dup.cold+0x17/0x23
sysfs_create_dir_ns+0xce/0xe0
kobject_add_internal+0xba/0x250
kobject_add+0x96/0xc0
? get_device_parent+0xde/0x1e0
device_add+0xe2/0x870
__power_supply_register.part.0+0x20f/0x3f0
? wake_up_q+0x4e/0x90
sysfs_add_battery+0xa4/0x1d0 [battery]
acpi_battery_update+0x19e/0x290 [battery]
acpi_battery_notify+0x50/0x120 [battery]
acpi_ev_notify_dispatch+0x49/0x70
acpi_os_execute_deferred+0x1a/0x30
process_one_work+0x177/0x330
worker_thread+0x251/0x390
? __pfx_worker_thread+0x10/0x10
kthread+0xd2/0x100
? __pfx_kthread+0x10/0x10
ret_from_fork+0x34/0x50
? __pfx_kthread+0x10/0x10
ret_from_fork_asm+0x1a/0x30
</TASK>
kobject: kobject_add_internal failed for BAT1 with -EEXIST, don't try to register things with the same name in the same directory.
There are also other scenarios in which analogous issues may occur.
Address this by using a common lock in all of the code paths leading
to updates of driver interfaces: ACPI Notify () handler, system resume
callback and post-resume notification, device addition and removal.
This new lock replaces sysfs_lock that has been used only in
sysfs_remove_battery() which now is going to be always called under
the new lock, so it doesn't need any internal locking any more.
Fixes: 1066625155 ("ACPI: battery: Install Notify() handler directly")
Closes: https://lore.kernel.org/linux-acpi/20250910142653.313360-1-luogf2025@163.com/
Reported-by: GuangFei Luo <luogf2025@163.com>
Tested-by: GuangFei Luo <luogf2025@163.com>
Cc: 6.6+ <stable@vger.kernel.org> # 6.6+
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 496f9372ea upstream.
In the ACPI debugger interface, the helper functions for read and write
operations use "int" as the length parameter data type. When a large
"size_t count" is passed from the file operations, this cast to "int"
results in truncation and a negative value due to signed integer
representation.
Logically, this negative number propagates to the min() calculation,
where it is selected over the positive buffer space value, leading to
unexpected behavior. Subsequently, when this negative value is used in
copy_to_user() or copy_from_user(), it is interpreted as a large positive
value due to the unsigned nature of the size parameter in these functions,
causing the copy operations to attempt handling sizes far beyond the
intended buffer limits.
Address the issue by:
- Changing the length parameters in acpi_aml_read_user() and
acpi_aml_write_user() from "int" to "size_t", aligning with the
expected unsigned size semantics.
- Updating return types and local variables in acpi_aml_read() and
acpi_aml_write() to "ssize_t" for consistency with kernel file
operation conventions.
- Using "size_t" for the "n" variable to ensure calculations remain
unsigned.
- Using min_t() for circ_count_to_end() and circ_space_to_end() to
ensure type-safe comparisons and prevent integer overflow.
Signed-off-by: Amir Mohammad Jahangirzad <a.jahangirzad@gmail.com>
Link: https://patch.msgid.link/20250923013113.20615-1-a.jahangirzad@gmail.com
[ rjw: Changelog tweaks, local variable definitions ordering adjustments ]
Fixes: 8cfb0cdf07 ("ACPI / debugger: Add IO interface to access debugger functionalities")
Cc: 4.5+ <stable@vger.kernel.org> # 4.5+
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 22c65572ef upstream.
ACPICA commit 4623b3369f3aa1ec5229d461e91c514510a96912
Partially revert commit 70662db73d ("ACPICA: Apply ACPI_NONSTRING in
more places") as I've yet again incorrectly applied the ACPI_NONSTRING
attribute where it is not needed.
A warning was initially reported by Collin Funk [1], and further review
by Jiri Slaby [2] highlighted another issue related to the same commit.
Drop the ACPI_NONSTRING attribute to fix the issue.
Fixes: 70662db73d ("ACPICA: Apply ACPI_NONSTRING in more places")
Link: https://lore.kernel.org/all/87ecvpcypw.fsf@gmail.com [1]
Link: https://lore.kernel.org/all/5c210121-c9b8-4458-b1ad-0da24732ac72@kernel.org [2]
Link: 4623b336
Reported-by: Jiri Slaby <jirislaby@kernel.org>
Signed-off-by: Ahmed Salem <x0rw3ll@gmail.com>
Cc: 6.16+ <stable@vger.kernel.org> # 6.16+
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d0759b1098 upstream.
The ACPI handle passed to acpi_extract_properties() as the first
argument represents the ACPI namespace scope in which to look for
objects returning buffers associated with buffer properties.
For _DSD objects located immediately under ACPI devices, this handle is
the same as the handle of the device object holding the _DSD, but for
data-only subnodes it is not so.
First of all, data-only subnodes are represented by objects that
cannot hold other objects in their scopes (like control methods).
Therefore a data-only subnode handle cannot be used for completing
relative pathname segments, so the current code in
in acpi_nondev_subnode_extract() passing a data-only subnode handle
to acpi_extract_properties() is invalid.
Moreover, a data-only subnode of device A may be represented by an
object located in the scope of device B (which kind of makes sense,
for instance, if A is a B's child). In that case, the scope in
question would be the one of device B. In other words, the scope
mentioned above is the same as the scope used for subnode object
lookup in acpi_nondev_subnode_extract().
Accordingly, rearrange that function to use the same scope for the
extraction of properties and subnode object lookup.
Fixes: 103e10c69c ("ACPI: property: Add support for parsing buffer property UUID")
Cc: 6.0+ <stable@vger.kernel.org> # 6.0+
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Tested-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 16ae95800b upstream.
Partially revert commit 70662db73d ("ACPICA: Apply ACPI_NONSTRING in
more places") as I've yet again incorrectly applied the ACPI_NONSTRING
attribute where it is not needed.
A warning was initially reported by Collin Funk [1], and further review
by Jiri Slaby [2] highlighted another issue related to the same commit.
Drop the ACPI_NONSTRING attribute to fix the issue.
Fixes: 70662db73d ("ACPICA: Apply ACPI_NONSTRING in more places")
Link: https://lore.kernel.org/all/87ecvpcypw.fsf@gmail.com [1]
Link: https://lore.kernel.org/all/5c210121-c9b8-4458-b1ad-0da24732ac72@kernel.org [2]
Link: a6ee09ca
Reported-by: Collin Funk <collin.funk1@gmail.com>
Signed-off-by: Ahmed Salem <x0rw3ll@gmail.com>
Cc: 6.16+ <stable@vger.kernel.org> # 6.16+
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 9338d660b7 ]
When building s390 defconfig with binutils older than 2.32, there are
several warnings during the final linking stage:
s390-linux-ld: .tmp_vmlinux1: warning: allocated section `.got.plt' not in segment
s390-linux-ld: .tmp_vmlinux2: warning: allocated section `.got.plt' not in segment
s390-linux-ld: vmlinux.unstripped: warning: allocated section `.got.plt' not in segment
s390-linux-objcopy: vmlinux: warning: allocated section `.got.plt' not in segment
s390-linux-objcopy: st7afZyb: warning: allocated section `.got.plt' not in segment
binutils commit afca762f598 ("S/390: Improve partial relro support for
64 bit") [1] in 2.32 changed where .got.plt is emitted, avoiding the
warning.
The :NONE in the .vmlinux.info output section description changes the
segment for subsequent allocated sections. Move .vmlinux.info right
above the discards section to place all other sections in the previously
defined segment, .data.
Fixes: 30226853d6 ("s390: vmlinux.lds.S: explicitly handle '.got' and '.plt' sections")
Link: https://sourceware.org/git/?p=binutils-gdb.git;a=commit;h=afca762f598d453c563f244cd3777715b1a0cb72 [1]
Acked-by: Alexander Gordeev <agordeev@linux.ibm.com>
Acked-by: Alexey Gladkov <legion@kernel.org>
Acked-by: Nicolas Schier <nsc@kernel.org>
Link: https://patch.msgid.link/20251008-kbuild-fix-modinfo-regressions-v1-3-9fc776c5887c@kernel.org
Signed-off-by: Nathan Chancellor <nathan@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8d18ef04f9 ]
In the upcoming changes, the ELF_DETAILS macro will be extended with
the ".modinfo" section, which will cause an error:
>> s390x-linux-ld: .tmp_vmlinux1: warning: allocated section `.modinfo' not in segment
>> s390x-linux-ld: .tmp_vmlinux2: warning: allocated section `.modinfo' not in segment
>> s390x-linux-ld: vmlinux.unstripped: warning: allocated section `.modinfo' not in segment
This happens because the .vmlinux.info use :NONE to override the default
segment and tell the linker to not put the section in any segment at all.
To avoid this, we need to change the sections order that will be placed
in the default segment.
Cc: Heiko Carstens <hca@linux.ibm.com>
Cc: Vasily Gorbik <gor@linux.ibm.com>
Cc: Alexander Gordeev <agordeev@linux.ibm.com>
Cc: linux-s390@vger.kernel.org
Reported-by: kernel test robot <lkp@intel.com>
Closes: https://lore.kernel.org/oe-kbuild-all/202506062053.zbkFBEnJ-lkp@intel.com/
Signed-off-by: Alexey Gladkov <legion@kernel.org>
Acked-by: Heiko Carstens <hca@linux.ibm.com>
Link: https://patch.msgid.link/20d40a7a3a053ba06a54155e777dcde7fdada1db.1758182101.git.legion@kernel.org
Signed-off-by: Nathan Chancellor <nathan@kernel.org>
Stable-dep-of: 9338d660b7 ("s390/vmlinux.lds.S: Move .vmlinux.info to end of allocatable sections")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8ec3af916f ]
Prior to binutils commit c12d9fa2afe ("Support objcopy
--remove-section=.relaFOO") [1] in 2.32, stripping relocation sections
required the trailing period (i.e., '.rel.*') to work properly.
After commit 3e86e4d74c ("kbuild: keep .modinfo section in
vmlinux.unstripped"), there is an error with binutils 2.31.1 or earlier
because these sections are not properly removed:
s390-linux-objcopy: st6tO8Ev: symbol `.modinfo' required but not present
s390-linux-objcopy:st6tO8Ev: no symbols
Add the old pattern to resolve this issue (along with a comment to allow
cleaning this when binutils 2.32 or newer is the minimum supported
version). While the aforementioned kbuild change exposes this, the
pattern was originally changed by commit 71d815bf5d ("kbuild: Strip
runtime const RELA sections correctly"), where it would still be
incorrect with binutils older than 2.32.
Fixes: 71d815bf5d ("kbuild: Strip runtime const RELA sections correctly")
Link: https://sourceware.org/git/?p=binutils-gdb.git;a=commit;h=c12d9fa2afe7abcbe407a00e15719e1a1350c2a7 [1]
Reported-by: Linux Kernel Functional Testing <lkft@linaro.org>
Closes: https://lore.kernel.org/CA+G9fYvVktRhFtZXdNgVOL8j+ArsJDpvMLgCitaQvQmCx=hwOQ@mail.gmail.com/
Acked-by: Ard Biesheuvel <ardb@kernel.org>
Acked-by: Alexey Gladkov <legion@kernel.org>
Acked-by: Nicolas Schier <nsc@kernel.org>
Link: https://patch.msgid.link/20251008-kbuild-fix-modinfo-regressions-v1-2-9fc776c5887c@kernel.org
Signed-off-by: Nathan Chancellor <nathan@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3e86e4d74c ]
Keep the .modinfo section during linking, but strip it from the final
vmlinux.
Adjust scripts/mksysmap to exclude modinfo symbols from kallsyms.
This change will allow the next commit to extract the .modinfo section
from the vmlinux.unstripped intermediate.
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
Signed-off-by: Alexey Gladkov <legion@kernel.org>
Reviewed-by: Nicolas Schier <nsc@kernel.org>
Link: https://patch.msgid.link/aaf67c07447215463300fccaa758904bac42f992.1758182101.git.legion@kernel.org
Signed-off-by: Nathan Chancellor <nathan@kernel.org>
Stable-dep-of: 8ec3af916f ("kbuild: Add '.rel.*' strip pattern for vmlinux")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0ce5139fd9 ]
Generate the intermediate vmlinux.unstripped regardless of
CONFIG_ARCH_VMLINUX_NEEDS_RELOCS.
If CONFIG_ARCH_VMLINUX_NEEDS_RELOCS is unset, vmlinux.unstripped and
vmlinux are identiacal.
This simplifies the build rule, and allows to strip more sections
by adding them to remove-section-y.
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
Reviewed-by: Nicolas Schier <nsc@kernel.org>
Link: https://patch.msgid.link/a48ca543fa2305bd17324f41606dcaed9b19f2d4.1758182101.git.legion@kernel.org
Signed-off-by: Nathan Chancellor <nathan@kernel.org>
Stable-dep-of: 8ec3af916f ("kbuild: Add '.rel.*' strip pattern for vmlinux")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4f375ade6a ]
When unpinning a BPF hash table (htab or htab_lru) that contains internal
structures (timer, workqueue, or task_work) in its values, a BUG warning
is triggered:
BUG: sleeping function called from invalid context at kernel/bpf/hashtab.c:244
in_atomic(): 1, irqs_disabled(): 0, non_block: 0, pid: 14, name: ksoftirqd/0
...
The issue arises from the interaction between BPF object unpinning and
RCU callback mechanisms:
1. BPF object unpinning uses ->free_inode() which schedules cleanup via
call_rcu(), deferring the actual freeing to an RCU callback that
executes within the RCU_SOFTIRQ context.
2. During cleanup of hash tables containing internal structures,
htab_map_free_internal_structs() is invoked, which includes
cond_resched() or cond_resched_rcu() calls to yield the CPU during
potentially long operations.
However, cond_resched() or cond_resched_rcu() cannot be safely called from
atomic RCU softirq context, leading to the BUG warning when attempting
to reschedule.
Fix this by changing from ->free_inode() to ->destroy_inode() and rename
bpf_free_inode() to bpf_destroy_inode() for BPF objects (prog, map, link).
This allows direct inode freeing without RCU callback scheduling,
avoiding the invalid context warning.
Reported-by: Le Chen <tom2cat@sjtu.edu.cn>
Closes: https://lore.kernel.org/all/1444123482.1827743.1750996347470.JavaMail.zimbra@sjtu.edu.cn/
Fixes: 68134668c1 ("bpf: Add map side support for bpf timers.")
Suggested-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: KaFai Wan <kafai.wan@linux.dev>
Acked-by: Yonghong Song <yonghong.song@linux.dev>
Link: https://lore.kernel.org/r/20251008102628.808045-2-kafai.wan@linux.dev
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b5f8aa8d4b ]
The slimbus regmap passed to the GPIO driver down from MFD does not use
fast_io. This means a mutex is used for locking and thus this GPIO chip
must not be used in atomic context. Change the can_sleep switch in
struct gpio_chip to true.
Fixes: 59c3246834 ("gpio: wcd934x: Add support to wcd934x gpio controller")
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8a81236f2c ]
The tpm_tis_write8() call specifies arguments in wrong order. Should be
(data, addr, value) not (data, value, addr). The initial correct order
was changed during the major refactoring when the code was split.
Fixes: 41a5e1cf1f ("tpm/tpm_tis: Split tpm_tis driver into a core and TCG TIS compliant phy")
Signed-off-by: Gunnar Kudrjavets <gunnarku@amazon.com>
Reviewed-by: Justinien Bouron <jbouron@amazon.com>
Reviewed-by: Jarkko Sakkinen <jarkko@kernel.org>
Reviewed-by: Paul Menzel <pmenzel@molgen.mpg.de>
Signed-off-by: Jarkko Sakkinen <jarkko@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 057ac50638 ]
EA $LXMOD is required for WSL non-symlink reparse points.
Fixes: ef86ab131d ("cifs: Fix querying of WSL CHR and BLK reparse points over SMB1")
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Steve French <stfrench@microsoft.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b95cd1bdf5 ]
Don't reuse open handle when changing timestamps to prevent the server
from disabling automatic timestamp updates as per MS-FSA 2.1.4.17.
---8<---
import os
import time
filename = '/mnt/foo'
def print_stat(prefix):
st = os.stat(filename)
print(prefix, ': ', time.ctime(st.st_atime), time.ctime(st.st_ctime))
fd = os.open(filename, os.O_CREAT|os.O_TRUNC|os.O_WRONLY, 0o644)
print_stat('old')
os.utime(fd, None)
time.sleep(2)
os.write(fd, b'foo')
os.close(fd)
time.sleep(2)
print_stat('new')
---8<---
Before patch:
$ mount.cifs //srv/share /mnt -o ...
$ python3 run.py
old : Fri Oct 3 14:01:21 2025 Fri Oct 3 14:01:21 2025
new : Fri Oct 3 14:01:21 2025 Fri Oct 3 14:01:21 2025
After patch:
$ mount.cifs //srv/share /mnt -o ...
$ python3 run.py
old : Fri Oct 3 17:03:34 2025 Fri Oct 3 17:03:34 2025
new : Fri Oct 3 17:03:36 2025 Fri Oct 3 17:03:36 2025
Fixes: b6f2a0f89d ("cifs: for compound requests, use open handle if possible")
Signed-off-by: Paulo Alcantara (Red Hat) <pc@manguebit.org>
Cc: Frank Sorenson <sorenson@redhat.com>
Reviewed-by: David Howells <dhowells@redhat.com>
Cc: linux-cifs@vger.kernel.org
Signed-off-by: Steve French <stfrench@microsoft.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0cc380d0e1 ]
The return value of copy_to_iter() function will never be negative,
it is the number of bytes copied, or zero if nothing was copied.
Update the check to treat 0 as an error, and return -1 in that case.
Fixes: d08089f649 ("cifs: Change the I/O paths to use an iterator rather than a page list")
Acked-by: Tom Talpey <tom@talpey.com>
Reviewed-by: David Howells <dhowells@redhat.com>
Signed-off-by: Fushuai Wang <wangfushuai@baidu.com>
Signed-off-by: Steve French <stfrench@microsoft.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6bb73db694 ]
Move the ssize check to the start in essiv_aead_crypt so that
it's also checked for decryption and in-place encryption.
Reported-by: Muhammad Alifa Ramdhan <ramdhan@starlabs.sg>
Fixes: be1eb7f78a ("crypto: essiv - create wrapper template for ESSIV generation")
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e9a9dcb4cc ]
Don't forget to adjust the source offset in io_copy_page(), otherwise
it'll be copying into the same location in some cases for highmem
setups.
Fixes: e67645bb7f ("io_uring/zcrx: prepare fallback for larger pages")
Signed-off-by: Pavel Begunkov <asml.silence@gmail.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e84945bdc6 ]
Jakub reported this self test flaking occasionally (fails, but passes on
re-run) on debug kernels.
This is because the test checks for elapsed time to determine if both
connections were established in parallel.
Rework this to no longer depend on timing.
Use busywait helper to check that both sockets have moved to established
state and then query the conntrack engine for the two entries.
Reported-by: Jakub Kicinski <kuba@kernel.org>
Closes: https://lore.kernel.org/netfilter-devel/20250926163318.40d1a502@kernel.org/
Fixes: 117e149e26 ("selftests: netfilter: test nat source port clash resolution interaction with tcp early demux")
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a126ab6b26 ]
Jakub reports spurious failure of nft_fib.sh test.
This is caused by a subtle bug inherited when i moved faulty ping
from one test case to another.
nft_fib.sh not only checks that the fib expression matched, it also
records the number of matches and then validates we have the expected
count. When I did this it was under the assumption that we would
have 0 to n matching packets. In case of the failure, the entry has
n+1 matching packets.
This happens because ping_unreachable helper uses "ping -c 1 -w 1",
instead of the intended "-W". -w alters the meaning of -c (count),
namely, its then treated as number of wanted *replies* instead of
"number of packets to send".
So, in some cases, ping -c 1 -w 1 ends up sending two packets which then
makes the test fail due to the higher-than-expected packet count.
Fix the actual bug (s/-w/-W) and also change the error handling:
1. Show the number of expected packets in the error message
2. Always try to delete the key from the set.
Else, later test that makes sure we don't have unexpected keys
in there will always fail as well.
Reported-by: Jakub Kicinski <kuba@kernel.org>
Closes: https://lore.kernel.org/netfilter-devel/20250927090709.0b3cd783@kernel.org/
Fixes: 98287045c9 ("selftests: netfilter: move fib vrf test to nft_fib.sh")
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f359b809d5 ]
Referencing a synproxy stateful object from OUTPUT hook causes kernel
crash due to infinite recursive calls:
BUG: TASK stack guard page was hit at 000000008bda5b8c (stack is 000000003ab1c4a5..00000000494d8b12)
[...]
Call Trace:
__find_rr_leaf+0x99/0x230
fib6_table_lookup+0x13b/0x2d0
ip6_pol_route+0xa4/0x400
fib6_rule_lookup+0x156/0x240
ip6_route_output_flags+0xc6/0x150
__nf_ip6_route+0x23/0x50
synproxy_send_tcp_ipv6+0x106/0x200
synproxy_send_client_synack_ipv6+0x1aa/0x1f0
nft_synproxy_do_eval+0x263/0x310
nft_do_chain+0x5a8/0x5f0 [nf_tables
nft_do_chain_inet+0x98/0x110
nf_hook_slow+0x43/0xc0
__ip6_local_out+0xf0/0x170
ip6_local_out+0x17/0x70
synproxy_send_tcp_ipv6+0x1a2/0x200
synproxy_send_client_synack_ipv6+0x1aa/0x1f0
[...]
Implement objref and objrefmap expression validate functions.
Currently, only NFT_OBJECT_SYNPROXY object type requires validation.
This will also handle a jump to a chain using a synproxy object from the
OUTPUT hook.
Now when trying to reference a synproxy object in the OUTPUT hook, nft
will produce the following error:
synproxy_crash.nft: Error: Could not process rule: Operation not supported
synproxy name mysynproxy
^^^^^^^^^^^^^^^^^^^^^^^^
Fixes: ee394f96ad ("netfilter: nft_synproxy: add synproxy stateful object support")
Reported-by: Georg Pfuetzenreuter <georg.pfuetzenreuter@suse.com>
Closes: https://bugzilla.suse.com/1250237
Signed-off-by: Fernando Fernandez Mancera <fmancera@suse.de>
Reviewed-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 229c586b5e ]
Commit afddce13ce ("crypto: api - Add reqsize to crypto_alg")
introduced cra_reqsize field in crypto_alg struct to replace type
specific reqsize fields. It looks like this was introduced specifically
for ahash and acomp from the commit description as subsequent commits
add necessary changes in these alg frameworks.
However, this is being recommended for use in all crypto algs [1]
instead of setting reqsize using crypto_*_set_reqsize(). Using
cra_reqsize in skcipher algorithms, hence, causes memory
corruptions and crashes as the underlying functions in the algorithm
framework have not been updated to set the reqsize properly from
cra_reqsize. [2]
Add proper set_reqsize calls in the skcipher init function to
properly initialize reqsize for these algorithms in the framework.
[1]: https://lore.kernel.org/linux-crypto/aCL8BxpHr5OpT04k@gondor.apana.org.au/
[2]: https://gist.github.com/Pratham-T/24247446f1faf4b7843e4014d5089f6b
Fixes: afddce13ce ("crypto: api - Add reqsize to crypto_alg")
Fixes: 52f641bc63 ("crypto: ti - Add driver for DTHE V2 AES Engine (ECB, CBC)")
Signed-off-by: T Pratham <t-pratham@ti.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2c95a756e0 ]
The TPS23881 improves on the TPS23880 with current sense resistors reduced
from 255 mOhm to 200 mOhm. This has a direct impact on the scaling of the
current measurement. However, the latest TPS23881 data sheet from May 2023
still shows the scaling of the TPS23880 model.
Fixes: 7f076ce3f1 ("net: pse-pd: tps23881: Add support for power limit and measurement features")
Signed-off-by: Thomas Wismer <thomas.wismer@scs.ch>
Acked-by: Kory Maincent <kory.maincent@bootlin.com>
Link: https://patch.msgid.link/20251006204029.7169-2-thomas@wismer.xyz
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 58e6fc2fb9 ]
kfd_lookup_process_by_pid hold the kfd process reference to ensure it
doesn't get destroyed while sending the segfault event to user space.
Calling kfd_lookup_process_by_pid as function parameter leaks the kfd
process refcount and miss the NULL pointer check if app process is
already destroyed.
Fixes: 2d274bf709 ("amd/amdkfd: Trigger segfault for early userptr unmmapping")
Signed-off-by: Philip Yang <Philip.Yang@amd.com>
Reviewed-by: Harish Kasiviswanathan <Harish.Kasiviswanathan@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0e190a0446 ]
Scaling doesn't work on DCE6 at the moment, the current
register programming produces incorrect output when using
fractional scaling (between 100-200%) on resolutions higher
than 1080p.
Disable it until we figure out how to program it properly.
Fixes: 7c15fd86aa ("drm/amd/display: dc/dce: add initial DCE6 support (v10)")
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Timur Kristóf <timur.kristof@gmail.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a7dc87f344 ]
SCL_SCALER_ENABLE can be used to enable/disable the scaler
on DCE6. Program it to 0 when scaling isn't used, 1 when used.
Additionally, clear some other registers when scaling is
disabled and program the SCL_UPDATE register as recommended.
This fixes visible glitches for users whose BIOS sets up a
mode with scaling at boot, which DC was unable to clean up.
Fixes: b70aaf5586 ("drm/amd/display: dce_transform: add DCE6 specific macros,functions")
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Timur Kristóf <timur.kristof@gmail.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c0aa7cf49d ]
Previously, the code would set a bit field which didn't exist
on DCE6 so it would be effectively a no-op.
Fixes: b70aaf5586 ("drm/amd/display: dce_transform: add DCE6 specific macros,functions")
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Timur Kristóf <timur.kristof@gmail.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3f39f56520 ]
pm_runtime_get_sync() and pm_runtime_put_autosuspend() were previously
called in cmdq_mbox_send_data(), which is under a spinlock in msg_submit()
(mailbox.c). This caused lockdep warnings such as "sleeping function
called from invalid context" when running with lockdebug enabled.
The BUG report:
BUG: sleeping function called from invalid context at drivers/base/power/runtime.c:1164
in_atomic(): 1, irqs_disabled(): 128, non_block: 0, pid: 3616, name: kworker/u17:3
preempt_count: 1, expected: 0
RCU nest depth: 0, expected: 0
INFO: lockdep is turned off.
irq event stamp: 0
CPU: 1 PID: 3616 Comm: kworker/u17:3 Not tainted 6.1.87-lockdep-14133-g26e933aca785 #1
Hardware name: Google Ciri sku0/unprovisioned board (DT)
Workqueue: imgsys_runner imgsys_runner_func
Call trace:
dump_backtrace+0x100/0x120
show_stack+0x20/0x2c
dump_stack_lvl+0x84/0xb4
dump_stack+0x18/0x48
__might_resched+0x354/0x4c0
__might_sleep+0x98/0xe4
__pm_runtime_resume+0x70/0x124
cmdq_mbox_send_data+0xe4/0xb1c
msg_submit+0x194/0x2dc
mbox_send_message+0x190/0x330
imgsys_cmdq_sendtask+0x1618/0x2224
imgsys_runner_func+0xac/0x11c
process_one_work+0x638/0xf84
worker_thread+0x808/0xcd0
kthread+0x24c/0x324
ret_from_fork+0x10/0x20
Additionally, pm_runtime_put_autosuspend() should be invoked from the
GCE IRQ handler to ensure the hardware has actually completed its work.
To resolve these issues, remove the pm_runtime calls from
cmdq_mbox_send_data() and delegate power management responsibilities
to the client driver.
Fixes: 8afe816b0c ("mailbox: mtk-cmdq-mailbox: Implement Runtime PM with autosuspend")
Signed-off-by: Jason-JH Lin <jason-jh.lin@mediatek.com>
Signed-off-by: Jassi Brar <jassisinghbrar@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 22239eb258 ]
When configuring IPsec packet offload in tunnel mode, the driver tries
to create tunnel reformat objects unconditionally. This is incorrect,
because tunnel mode is only permitted under specific encapsulation
settings, and that decision is already made when the flow table is
created.
The offending commit attempted to block this case in the state add
path, but the check there happens too late and does not prevent the
reformat from being configured.
Fix by taking short reservations for both the eswitch mode and the
encap at the start of state setup. This preserves the block ordering
(mode --> encap) used later: the mode is blocked during RX/TX get, and
the encap is blocked during flow-table creation. This lets us fail
early if either reservation cannot be obtained, it means a mode
transition is underway or a conflicting configuration already owns
encap. If both succeed, the flow-table path later takes the ownership
and the reservations are released on exit.
Fixes: 146c196b60 ("net/mlx5e: Create IPsec table with tunnel support only when encap is disabled")
Signed-off-by: Carolina Jubran <cjubran@nvidia.com>
Reviewed-by: Jianbo Liu <jianbol@nvidia.com>
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Link: https://patch.msgid.link/1759652999-858513-3-git-send-email-tariqt@nvidia.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7593439c13 ]
When creating IPsec flow tables with tunnel mode enabled, the driver
uses mlx5_eswitch_block_encap() to prevent tunnel encapsulation
conflicts across different domains (NIC_RX/NIC_TX and FDB), since the
firmware doesn’t allow both at the same time.
Currently, the driver attempts to reserve tunnel mode unconditionally
for both NIC and FDB IPsec tables. This can lead to conflicting tunnel
mode setups, for example, if a flow table was created in the FDB
domain with tunnel offload enabled, and we later try to create another
one in the NIC, or vice versa.
To resolve this, adjust the blocking logic so that tunnel mode is only
reserved by NIC flows. This ensures that tunnel offload is exclusively
used in either the NIC or the FDB, and avoids unintended offload
conflicts.
Fixes: 1762f132d5 ("net/mlx5e: Support IPsec packet offload for RX in switchdev mode")
Fixes: c6c2bf5db4 ("net/mlx5e: Support IPsec packet offload for TX in switchdev mode")
Signed-off-by: Carolina Jubran <cjubran@nvidia.com>
Reviewed-by: Jianbo Liu <jianbol@nvidia.com>
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Link: https://patch.msgid.link/1759652999-858513-2-git-send-email-tariqt@nvidia.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c9d1b0b542 ]
The sparx5 driver programs UC/MC/BC flooding in sparx5_update_fwd() by
unconditionally applying bridge_fwd_mask to all flood PGIDs. Any bridge
topology change that triggers sparx5_update_fwd() (for example enslaving
another port) therefore reinstalls flooding in hardware for already
bridged ports, regardless of their per-port flood flags.
This results in clobbering of the flood masks, and desynchronization
between software and hardware: the bridge still reports “flood off” for
the port, but hardware has flooding enabled due to unconditional PGID
reprogramming.
Steps to reproduce:
$ ip link add br0 type bridge
$ ip link set br0 up
$ ip link set eth0 master br0
$ ip link set eth0 up
$ bridge link set dev eth0 flood off
$ ip link set eth1 master br0
$ ip link set eth1 up
At this point, flooding is silently re-enabled for eth0. Software still
shows “flood off” for eth0, but hardware has flooding enabled.
To fix this, flooding is now set explicitly during bridge join/leave,
through sparx5_port_attr_bridge_flags():
On bridge join, UC/MC/BC flooding is enabled by default.
On bridge leave, UC/MC/BC flooding is disabled.
sparx5_update_fwd() no longer touches the flood PGIDs, clobbering
the flood masks, and desynchronizing software and hardware.
Initialization of the flooding PGIDs have been moved to
sparx5_start(). This is required as flooding PGIDs defaults to
0x3fffffff in hardware and the initialization was previously handled
in sparx5_update_fwd(), which was removed.
With this change, user-configured flooding flags persist across bridge
updates and are no longer overridden by sparx5_update_fwd().
Fixes: d6fce51419 ("net: sparx5: add switching support")
Signed-off-by: Daniel Machon <daniel.machon@microchip.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20251003-fix-flood-fwd-v1-1-48eb478b2904@microchip.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4dc8b26a3a ]
When accessing an MDIO register using single-byte smbus accesses, we have to
perform 2 consecutive operations targeting the same address,
first accessing the MSB then the LSB of the 16 bit register:
read_1_byte(addr); <- returns MSB of register at address 'addr'
read_1_byte(addr); <- returns LSB
Some PHY devices present in SFP such as the Broadcom 5461 don't like
seeing foreign i2c transactions in-between these 2 smbus accesses, and
will return the MSB a second time when trying to read the LSB :
read_1_byte(addr); <- returns MSB
i2c_transaction_for_other_device_on_the_bus();
read_1_byte(addr); <- returns MSB again
Given the already fragile nature of accessing PHYs/SFPs with single-byte
smbus accesses, it's safe to say that this Broadcom PHY may not be the
only one acting like this.
Let's therefore hold the i2c bus lock while performing our smbus
transactions to avoid interleaved accesses.
Fixes: d4bd3aca33 ("net: mdio: mdio-i2c: Add support for single-byte SMBus operations")
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Reviewed-by: Kory Maincent <kory.maincent@bootlin.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/20251003070311.861135-1-maxime.chevallier@bootlin.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 23f3770e1a ]
Cilium has a BPF egress gateway feature which forces outgoing K8s Pod
traffic to pass through dedicated egress gateways which then SNAT the
traffic in order to interact with stable IPs outside the cluster.
The traffic is directed to the gateway via vxlan tunnel in collect md
mode. A recent BPF change utilized the bpf_redirect_neigh() helper to
forward packets after the arrival and decap on vxlan, which turned out
over time that the kmalloc-256 slab usage in kernel was ever-increasing.
The issue was that vxlan allocates the metadata_dst object and attaches
it through a fake dst entry to the skb. The latter was never released
though given bpf_redirect_neigh() was merely setting the new dst entry
via skb_dst_set() without dropping an existing one first.
Fixes: b4ab314149 ("bpf: Add redirect_neigh helper as redirect drop-in")
Reported-by: Yusuke Suzuki <yusuke.suzuki@isovalent.com>
Reported-by: Julian Wiedmann <jwi@isovalent.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Cc: Martin KaFai Lau <martin.lau@kernel.org>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: Jordan Rife <jrife@google.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Reviewed-by: Jordan Rife <jrife@google.com>
Reviewed-by: Jakub Kicinski <kuba@kernel.org>
Reviewed-by: Martin KaFai Lau <martin.lau@kernel.org>
Link: https://lore.kernel.org/r/20251003073418.291171-1-daniel@iogearbox.net
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit bb160e791a ]
The driver incorrectly determines SGI vs SPI interrupts by checking IRQ
number < 16, which fails with dynamic IRQ allocation. During unbind,
this causes improper SGI cleanup leading to kernel crash.
Add explicit irq_type field to pdata for reliable identification of SGI
interrupts (type-2) and only clean up SGI resources when appropriate.
Fixes: 6ffb163534 ("mailbox: zynqmp: handle SGI for shared IPI")
Signed-off-by: Harini T <harini.t@amd.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Jassi Brar <jassisinghbrar@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0aead8197f ]
The cleanup loop was starting at the wrong array index, causing
out-of-bounds access.
Start the loop at the correct index for zero-indexed arrays to prevent
accessing memory beyond the allocated array bounds.
Fixes: 4981b82ba2 ("mailbox: ZynqMP IPI mailbox controller")
Signed-off-by: Harini T <harini.t@amd.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Jassi Brar <jassisinghbrar@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 019e3f4550 ]
The ipi_mbox->dev.parent check is unreliable proxy for registration
status as it fails to protect against probe failures that occur after
the parent is assigned but before device_register() completes.
device_is_registered() is the canonical and robust method to verify the
registration status.
Remove ipi_mbox->dev.parent check in zynqmp_ipi_free_mboxes().
Fixes: 4981b82ba2 ("mailbox: ZynqMP IPI mailbox controller")
Signed-off-by: Harini T <harini.t@amd.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Jassi Brar <jassisinghbrar@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 341867f730 ]
The controller is registered using the device-managed function
'devm_mbox_controller_register()'. As documented in mailbox.c, this
ensures the devres framework automatically calls
mbox_controller_unregister() when device_unregister() is invoked, making
the explicit call unnecessary.
Remove redundant mbox_controller_unregister() call as
device_unregister() handles controller cleanup.
Fixes: 4981b82ba2 ("mailbox: ZynqMP IPI mailbox controller")
Signed-off-by: Harini T <harini.t@amd.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Jassi Brar <jassisinghbrar@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f3b601f900 ]
Since commit 22f72088ff ("tools headers: Update the syscall table with
the kernel sources") the arm64 syscall header is generated at build
time. Later, commit bfb713ea53 ("perf tools: Fix arm64 build by
generating unistd_64.h") added a dependency to libperf to guarantee that
this header was created before building libperf or perf itself.
However, libjvmti also requires this header but does not depend on
libperf, leading to build failures such as:
In file included from /usr/include/sys/syscall.h:24,
from /usr/include/syscall.h:1,
from jvmti/jvmti_agent.c:36:
tools/arch/arm64/include/uapi/asm/unistd.h:2:10: fatal error: asm/unistd_64.h: No such file or directory
2 | #include <asm/unistd_64.h>
Fix this by ensuring that libperf is built before libjvmti, so that
unistd_64.h is always available.
Fixes: 22f72088ff ("tools headers: Update the syscall table with the kernel sources")
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Vincent Minet <v.minet@criteo.com>
Link: https://lore.kernel.org/r/20250922053702.2688374-1-v.minet@criteo.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 21b29e74ff ]
Some applications (like selftests/net/tcp_mmap.c) call SO_RCVLOWAT
on their listener, before accept().
This has an unfortunate effect on wscale selection in
tcp_select_initial_window() during 3WHS.
For instance, tcp_mmap was negotiating wscale 4, regardless
of tcp_rmem[2] and sysctl_rmem_max.
Do not change tp->window_clamp if it is zero
or bigger than our computed value.
Zero value is special, it allows tcp_select_initial_window()
to enable autotuning.
Note that SO_RCVLOWAT use on listener is probably not wise,
because tp->scaling_ratio has a default value, possibly wrong.
Fixes: d1361840f8 ("tcp: fix SO_RCVLOWAT and RCVBUF autotuning")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: Kuniyuki Iwashima <kuniyu@google.com>
Reviewed-by: Neal Cardwell <ncardwell@google.com>
Link: https://patch.msgid.link/20251003184119.2526655-1-edumazet@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c6a43bc3e8 ]
When passing a list to subprocess.Popen, each element maps to one argv
token. Current code bundles multiple Clang flags into a single element,
something like:
cmd = ['clang',
'--target=x86_64-linux-gnu -fintegrated-as -Wno-cast-function-type-mismatch',
'test-hello.c']
So Clang only sees one long, invalid option instead of separate flags,
as a result, the script cannot capture any log via PIPE.
Fix this by using shlex.split() to separate the string so each option
becomes its own argv element. The fixed list will be:
cmd = ['clang',
'--target=x86_64-linux-gnu',
'-fintegrated-as',
'-Wno-cast-function-type-mismatch',
'test-hello.c']
Fixes: 09e6f9f983 ("perf python: Fix splitting CC into compiler and options")
Signed-off-by: Leo Yan <leo.yan@arm.com>
Reviewed-by: Ian Rogers <irogers@google.com>
Link: https://lore.kernel.org/r/20251006-perf_build_android_ndk-v3-2-4305590795b2@arm.com
Cc: Palmer Dabbelt <palmer@dabbelt.com>
Cc: Albert Ou <aou@eecs.berkeley.edu>
Cc: Alexandre Ghiti <alex@ghiti.fr>
Cc: Nick Desaulniers <nick.desaulniers+lkml@gmail.com>
Cc: Justin Stitt <justinstitt@google.com>
Cc: Bill Wendling <morbo@google.com>
Cc: Adrian Hunter <adrian.hunter@intel.com>
Cc: Arnaldo Carvalho de Melo <acme@kernel.org>
Cc: Jiri Olsa <jolsa@kernel.org>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Nathan Chancellor <nathan@kernel.org>
Cc: James Clark <james.clark@linaro.org>
Cc: linux-riscv@lists.infradead.org
Cc: llvm@lists.linux.dev
Cc: Paul Walmsley <paul.walmsley@sifive.com>
Cc: linux-kernel@vger.kernel.org
Cc: linux-perf-users@vger.kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
