Per ovti,ov5640.yaml, the OV5640 power supplies are mandatory
properties.
Describe them to fix dt-schema warnings.
Signed-off-by: Fabio Estevam <festevam@denx.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Per ovti,ov5640.yaml, the OV5640 power supplies are mandatory
properties.
Describe them to fix dt-schema warnings.
As there are two different PMICs used on the imx8mn-evk variants,
describe the DOVDD OV5640 power supply in each board devicetree.
Signed-off-by: Fabio Estevam <festevam@denx.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Currently, there are several ADV7535 dt-schema warnings.
Fx them the same way as in commit efa97aed07 ("arm64: dts:
imx8mm-evk: Fix hdmi@3d node").
As there are two different PMICs used on the imx8mn-evk variants,
describe the ADV7535 power supplies in each board devicetree.
Fixes: 5aafda608f ("arm64: dts: imx8mn-evk: Add camera support")
Signed-off-by: Fabio Estevam <festevam@denx.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Per nxp,ptn5110.yaml, also pass the fallback "tcpci" compatible
to fix the following dt-schema warning:
usb-typec@50: compatible: ['nxp,ptn5110'] is too short
from schema $id: http://devicetree.org/schemas/usb/nxp,ptn5110.yaml#
Signed-off-by: Fabio Estevam <festevam@denx.de>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The clock-names property is not needed by usb controller node on imx8mm/n.
This will remove it.
Signed-off-by: Xu Yang <xu.yang_2@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
There are 2 Type-C ports and 2 USB controllers on i.MX93. Enable them.
Signed-off-by: Xu Yang <xu.yang_2@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
There are 2 USB controllers on i.MX93. Add them.
Acked-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Tested-by: Alexander Stein <alexander.stein@ew.tq-group.com> # TQMa9352LA/CA
Signed-off-by: Xu Yang <xu.yang_2@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add USB nodes on i.MX8ULP platform which has 2 USB controllers.
Signed-off-by: Xu Yang <xu.yang_2@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add support for Toradex Colibri iMX8DX SoM and Aster, Evaluation Board v3,
Iris and Iris v2 carrier boards the module can be mated in.
This SoM is a variant of the already supported Colibri iMX8QXP, using an
NXP i.MX8DX SoC instead of i.MX8QXP.
Link: https://www.toradex.com/computer-on-modules/colibri-arm-family/nxp-imx-8x
Signed-off-by: Hiago De Franco <hiago.franco@toradex.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add DTSI for i.MX8DX processor. According to 'i.MX 8DualX Industrial
Applications Processors Data Sheet', the GPU and shader use a clock of
372MHz. Therefore, this dtsi includes the imx8dxp.dtsi and changes the
clock accordingly.
Signed-off-by: Hiago De Franco <hiago.franco@toradex.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The devicetree files can be (re-)used in u-boot now, they are imported
on a regular basis (see OF_UPSTREAM option) there. Up until now, it
didn't matter for linux and there was just a combined devicetree
"-var3-ads2" (with ads2 being the carrier board). But if the devicetree
files are now reused in u-boot, we need to have an individual "-var3"
variant, because the bootloader is just using the bare "varN" devicetree
files. Split the "var3" off of the "-var3-ads2" devicetree.
Signed-off-by: Michael Walle <mwalle@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add lpuart device in cm40 subsystem.
Signed-off-by: Alice Guo <alice.guo@nxp.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Since commit 26c9d152eb ("dt-bindings: tpm: Consolidate TCG TIS
bindings"), several issues are reported by "make dtbs_check" for arm64
devicetrees:
The compatible property needs to contain the chip's name in addition to
the generic "tcg,tpm_tis-spi".
tpm@1: compatible: ['tcg,tpm_tis-spi'] is too short
from schema $id:
http://devicetree.org/schemas/tpm/tcg,tpm_tis-spi.yaml#
Fix these schema violations.
Gateworks Venice uses an Atmel ATTPM20P:
https://trac.gateworks.com/wiki/tpm
Cc: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The Emcraft Systems NavQ+ kit is a mobile robotics platform
based on NXP i.MX8 MPlus SoC.
The following interfaces and devices are enabled:
- eMMC
- Gigabit Ethernet
- RTC
- SD-Card
- UART console
Signed-off-by: Gilles Talis <gilles.talis@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The SoM used on this board does not bring down the pins for the QOS
ethernet and instead offers the 2nd ethernet as a PCI GbE device.
Set the alias as such and add the PCI bus topology for eth1 so that
boot firmware can set the local-mac-address property.
The eth1 device is behind a PCI switch:
# lspci -n
00:00.0 0604: 16c3:abcd (rev 01)
01:00.0 0604: 12d8:2608
02:01.0 0604: 12d8:2608
02:02.0 0604: 12d8:2608
02:03.0 0604: 12d8:2608
02:04.0 0604: 12d8:2608
c0:00.0 0200: 1055:7430 (rev 11)
# lspci -t
-[0000:00]---00.0-[01-ff]----00.0-[02-fe]--+-01.0-[03-41]--
+-02.0-[42-80]--
+-03.0-[81-bf]--
\-04.0-[c0-fe]----00.0
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The SoM used on this board does not bring down the pins for the QOS
ethernet and instead offers the 2nd ethernet as a PCI GbE device.
Set the alias as such and add the PCI bus topology for eth1 so that
boot firmware can set the local-mac-address property.
The eth1 device is behind a PCI switch:
# lspci -n
00:00.0 0604: 16c3:abcd (rev 01)
01:00.0 0604: 12d8:b404 (rev 01)
02:01.0 0604: 12d8:b404 (rev 01)
02:02.0 0604: 12d8:b404 (rev 01)
02:03.0 0604: 12d8:b404 (rev 01)
05:00.0 0200: 11ab:4380
# lspci -t
-[0000:00]---00.0-[01-ff]----00.0-[02-05]--+-01.0-[03]--
+-02.0-[04]--
\-03.0-[05]----00.0
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add asrc[0,1], esai0, spdif0, sai[4,5] and related lpcg node for
imx8 audio subsystem.
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
lpcg cell0 should be clock's 'indices' instead of 'index'.
imx_lpcg_of_clk_src_get(struct of_phandle_args *clkspec, void *data)
{
struct clk_hw_onecell_data *hw_data = data;
unsigned int idx = clkspec->args[0] / 4;
....
}
<@sai0_lpcg 1> will be the same as <@sai_lpcg 0>.
Replace 0 with IMX_LPCG_CLK_0 and replace 1 with IMX_LPCG_CLK_4.
It can work at iMX8QXP because IMX_LPCG_CLK_4 is ipg clock, which already
enabled. But for iMX8QM IMX_LPCG_CLK_4 is mclk, which trigger issue.
Fixes: 0a9279e9ae ("arm64: dts: imx8qxp: Add audio SAI nodes")
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
I2C bus recovery need a pinmux and gpio. So i2c driver can switch
gpio mode to toggle scl to recovery bus.
Add pinctrl-single node to every i2c bus on fsl-ls2160 layerscape
platform.
Signed-off-by: Carlos Song <carlos.song@nxp.com>
Reviewed-by: Frank Li <frank.li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
This commit adds device tree support for the NXP S32G3-based
S32G-VNP-RDB3 Board [1].
The S32G3 features an 8-core ARM Cortex-A53 based SoC developed by NXP.
The device tree files are derived from the official NXP downstream
Linux tree [2].
This addition encompasses a limited selection of peripherals that
are upstream-supported. Apart from the ARM System Modules
(GIC, Generic Timer, etc.), the following IPs have been validated:
* UART: fsl-linflexuart
* SDHC: fsl-imx-esdhc
Clock settings for the chip rely on ATF Firmware [3].
Pin control integration into the device tree is pending and currently
relies on Firmware/U-Boot settings [4].
These changes were validated using BSP39 Firmware/U-Boot from NXP [5].
The modifications enable booting the official Ubuntu 22.04 from NXP on
the RDB3 with default settings from the SD card and eMMC.
[1] https://www.nxp.com/design/design-center/designs/s32g3-vehicle-networking-reference-design:S32G-VNP-RDB3
[2] https://github.com/nxp-auto-linux/linux
[3] https://github.com/nxp-auto-linux/arm-trusted-firmware
[4] https://github.com/nxp-auto-linux/u-boot
[5] https://github.com/nxp-auto-linux/auto_yocto_bsp
Signed-off-by: Wadim Mueller <wafgo01@gmail.com>
Tested-by: Ghennadi Procopciuc <ghennadi.procopciuc@oss.nxp.com>
Reviewed-by: Ghennadi Procopciuc <ghennadi.procopciuc@oss.nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Support pca9451a on imx93-11x11-evk.
Signed-off-by: Joy Zou <joy.zou@nxp.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The production PDK3 carrier board rev.200 contains additional GPIO
expander to control power and reset signals for each CSI2 plug
separately. Describe this expander in the carrier board DT. The
label is used by sensor DTOs to reference the expander and its
signals.
Signed-off-by: Marek Vasut <marex@denx.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The imx8mp-venice-gw74xx revB PCB added an ADC rail for
VDD_1P0. Add it to the GSC ADC rails.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
SoM dts has enabled i2c bus IIC6 (dts i2c5), but defines no aliases.
LX2162A Clearfog dts has aliases for all i2c buses to ensure predictable
numbering for userspace. Add an additional alias for this extra bus.
Signed-off-by: Josua Mayer <josua@solid-run.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
SolidRun LX2162A SoM has an RTC on bus IIC6 (dts i2c5).
Enable this bus and add description for the rtc.
Signed-off-by: Josua Mayer <josua@solid-run.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Fix the following warning from a 'make dtbs W=1':
arch/arm64/boot/dts/freescale/imx8mp-venice-gw74xx-imx219.dtso:65.10-70.5:
Warning (unit_address_vs_reg): /fragment@3/__overlay__/ports/port@0:
node has a unit name, but no reg or ranges property
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
With the DSI output label in place, use the phandle directly.
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Also add a corresponding label so overlays can reference that node.
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Also add a corresponding label so overlays can reference that node.
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Also add a corresponding label so overlays can reference that node.
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Also add a corresponding label so overlays can reference that node.
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add PDM micphone sound card support, configure the pinmux.
This sound card supports recording sound from PDM micphone
and convert the PDM format data to PCM data.
Signed-off-by: Shengjiu Wang <shengjiu.wang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
AUD2HTX works as the cpu dai in HDMI audio sound card.
This sound card only support playback/output.
Signed-off-by: Shengjiu Wang <shengjiu.wang@nxp.com>
Acked-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The AUD2HTX is a digital module that provides a bridge between
the Audio Subsystem and the HDMI RTX Subsystem. This
module includes intermediate storage to queue SDMA transactions
prior to being synchronized and passed to the HDMI
RTX Subsystem over the Audio Link.
Signed-off-by: Shengjiu Wang <shengjiu.wang@nxp.com>
Reviewed-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
This adds the DT nodes for all the peripherals that make up the
HDMI display pipeline.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Adam Ford <aford173@gmail.com>
Tested-by: Marek Vasut <marex@denx.de>
Tested-by: Luca Ceresoli <luca.ceresoli@bootlin.com>
Reviewed-by: Luca Ceresoli <luca.ceresoli@bootlin.com>
Tested-by: Tommaso Merciai <tomm.merciai@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The HDMI irqsteer is a secondary interrupt controller within the HDMI
subsystem that maps all HDMI peripheral IRQs into a single upstream
IRQ line.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Adam Ford <aford173@gmail.com>
Tested-by: Marek Vasut <marex@denx.de>
Tested-by: Luca Ceresoli <luca.ceresoli@bootlin.com>
Tested-by: Tommaso Merciai <tomm.merciai@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
This adds the PGC and HDMI blk-ctrl nodes providing power control for
HDMI subsystem peripherals.
Signed-off-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Tested-by: Marek Vasut <marex@denx.de>
Tested-by: Luca Ceresoli <luca.ceresoli@bootlin.com>
Tested-by: Tommaso Merciai <tomm.merciai@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Per i.MX93 Reference Mannual Rev.4, 12/2023, there is no interrupt 268,
drop it.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add the uSDHC node for the boards that are based on S32G SoCs.
Signed-off-by: Ciprian Costea <ciprianmarian.costea@nxp.com>
Signed-off-by: Ghennadi Procopciuc <ghennadi.procopciuc@nxp.com>
Reviewed-by: Matthias Brugger <mbrugger@suse.com>
Reviewed-by: Chester Lin <chester62515@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Linux controls the clocks over SCMI on S32G SoCs. Therefore,
add the SCMI device tree node and the reserved region for SCMI
messages.
Signed-off-by: Catalin Udma <catalin-dan.udma@nxp.com>
Signed-off-by: Ghennadi Procopciuc <ghennadi.procopciuc@nxp.com>
Reviewed-by: Matthias Brugger <mbrugger@suse.com>
Reviewed-by: Chester Lin <chester62515@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
- Fix logic that is supposed to prevent placement of the kernel image
below LOAD_PHYSICAL_ADDR
- Use the firmware stack in the EFI stub when running in mixed mode
- Clear BSS only once when using mixed mode
- Check efi.get_variable() function pointer for NULL before trying to
call it
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQQQm/3uucuRGn1Dmh0wbglWLn0tXAUCZgCRgwAKCRAwbglWLn0t
XHozAP9jLdeGs1ReYZAn+W0QtW/SJHJznoPiHcktdNKG4rNX3QD9G3URu0f4jKCG
yvjw8qHM1pC2cihXXjABjf7gL7g6LAE=
=cNP7
-----END PGP SIGNATURE-----
Merge tag 'efi-fixes-for-v6.9-2' of git://git.kernel.org/pub/scm/linux/kernel/git/efi/efi
Pull EFI fixes from Ard Biesheuvel:
- Fix logic that is supposed to prevent placement of the kernel image
below LOAD_PHYSICAL_ADDR
- Use the firmware stack in the EFI stub when running in mixed mode
- Clear BSS only once when using mixed mode
- Check efi.get_variable() function pointer for NULL before trying to
call it
* tag 'efi-fixes-for-v6.9-2' of git://git.kernel.org/pub/scm/linux/kernel/git/efi/efi:
efi: fix panic in kdump kernel
x86/efistub: Don't clear BSS twice in mixed mode
x86/efistub: Call mixed mode boot services on the firmware's stack
efi/libstub: fix efi_random_alloc() to allocate memory at alloc_min or higher address
