Remove the "ghash-s390" crypto_shash algorithm, and replace it with an
implementation of ghash_blocks_arch() for the GHASH library.
This makes the GHASH library be optimized with CPACF. It also greatly
reduces the amount of s390-specific glue code that is needed, and it
fixes the issue where this GHASH optimization was disabled by default.
Acked-by: Ard Biesheuvel <ardb@kernel.org>
Link: https://lore.kernel.org/r/20260319061723.1140720-14-ebiggers@kernel.org
Signed-off-by: Eric Biggers <ebiggers@kernel.org>
Remove the "ghash-riscv64-zvkg" crypto_shash algorithm. Move the
corresponding assembly code into lib/crypto/, modify it to take the
length in blocks instead of bytes, and wire it up to the GHASH library.
This makes the GHASH library be optimized with the RISC-V Vector
Cryptography Extension. It also greatly reduces the amount of
riscv-specific glue code that is needed, and it fixes the issue where
this optimized GHASH code was disabled by default.
Note that this RISC-V code has multiple opportunities for improvement,
such as adding more parallelism, providing an optimized multiplication
function, and directly supporting POLYVAL. But for now, this commit
simply tweaks ghash_zvkg() slightly to make it compatible with the
library, then wires it up to ghash_blocks_arch().
ghash_preparekey_arch() is also implemented to store the copy of the raw
key needed by the vghsh.vv instruction.
Acked-by: Ard Biesheuvel <ardb@kernel.org>
Link: https://lore.kernel.org/r/20260319061723.1140720-13-ebiggers@kernel.org
Signed-off-by: Eric Biggers <ebiggers@kernel.org>
Remove the "p8_ghash" crypto_shash algorithm. Move the corresponding
assembly code into lib/crypto/, and wire it up to the GHASH library.
This makes the GHASH library be optimized for POWER8. It also greatly
reduces the amount of powerpc-specific glue code that is needed, and it
fixes the issue where this optimized GHASH code was disabled by default.
Note that previously the C code defined the POWER8 GHASH key format as
"u128 htable[16]", despite the assembly code only using four entries.
Fix the C code to use the correct key format. To fulfill the library
API contract, also make the key preparation work in all contexts.
Note that the POWER8 assembly code takes the accumulator in GHASH
format, but it actually byte-reflects it to get it into POLYVAL format.
The library already works with POLYVAL natively. For now, just wire up
this existing code by converting it to/from GHASH format in C code.
This should be cleaned up to eliminate the unnecessary conversion later.
Acked-by: Ard Biesheuvel <ardb@kernel.org>
Link: https://lore.kernel.org/r/20260319061723.1140720-12-ebiggers@kernel.org
Signed-off-by: Eric Biggers <ebiggers@kernel.org>
Rename the 'struct ghash_key' in arch/arm64/crypto/ghash-ce-glue.c to
prevent a naming conflict with the library 'struct ghash_key'. In
addition, declare the 'h' field with an explicit size, now that there's
no longer any reason for it to be a flexible array.
Update the comments in the assembly file to match the C code. Note that
some of these were out-of-date.
Acked-by: Ard Biesheuvel <ardb@kernel.org>
Link: https://lore.kernel.org/r/20260319061723.1140720-11-ebiggers@kernel.org
Signed-off-by: Eric Biggers <ebiggers@kernel.org>
Remove the "ghash-neon" crypto_shash algorithm. Move the corresponding
assembly code into lib/crypto/, and wire it up to the GHASH library.
This makes the GHASH library be optimized on arm64 (though only with
NEON, not PMULL; for now the goal is just parity with crypto_shash). It
greatly reduces the amount of arm64-specific glue code that is needed,
and it fixes the issue where this optimization was disabled by default.
To integrate the assembly code correctly with the library, make the
following tweaks:
- Change the type of 'blocks' from int to size_t
- Change the types of 'dg' and 'h' to polyval_elem. Note that this
simply reflects the format that the code was already using.
- Remove the 'head' argument, which is no longer needed.
- Remove the CFI stubs, as indirect calls are no longer used.
Acked-by: Ard Biesheuvel <ardb@kernel.org>
Link: https://lore.kernel.org/r/20260319061723.1140720-10-ebiggers@kernel.org
Signed-off-by: Eric Biggers <ebiggers@kernel.org>
arch/arm64/crypto/ghash-ce-core.S implements pmull_ghash_update_p8(),
which is used only by a crypto_shash implementation of GHASH. It also
implements other functions, including pmull_ghash_update_p64() and
others, which are used only by a crypto_aead implementation of AES-GCM.
While some code is shared between pmull_ghash_update_p8() and
pmull_ghash_update_p64(), it's not very much. Since
pmull_ghash_update_p8() will also need to be migrated into lib/crypto/
to achieve parity in the standalone GHASH support, let's move it into a
separate file ghash-neon-core.S.
Acked-by: Ard Biesheuvel <ardb@kernel.org>
Link: https://lore.kernel.org/r/20260319061723.1140720-9-ebiggers@kernel.org
Signed-off-by: Eric Biggers <ebiggers@kernel.org>
Remove the "ghash-neon" crypto_shash algorithm. Move the corresponding
assembly code into lib/crypto/, and wire it up to the GHASH library.
This makes the GHASH library be optimized on arm (though only with NEON,
not PMULL; for now the goal is just parity with crypto_shash). It
greatly reduces the amount of arm-specific glue code that is needed, and
it fixes the issue where this optimization was disabled by default.
To integrate the assembly code correctly with the library, make the
following tweaks:
- Change the type of 'blocks' from int to size_t.
- Change the types of 'dg' and 'h' to polyval_elem. Note that this
simply reflects the format that the code was already using, at least
on little endian CPUs. For big endian CPUs, add byte-swaps.
- Remove the 'head' argument, which is no longer needed.
Acked-by: Ard Biesheuvel <ardb@kernel.org>
Link: https://lore.kernel.org/r/20260319061723.1140720-8-ebiggers@kernel.org
Signed-off-by: Eric Biggers <ebiggers@kernel.org>
arch/arm/crypto/ghash-ce-core.S implements pmull_ghash_update_p8(),
which is used only by a crypto_shash implementation of GHASH. It also
implements other functions, including pmull_ghash_update_p64() and
others, which are used only by a crypto_aead implementation of AES-GCM.
While some code is shared between pmull_ghash_update_p8() and
pmull_ghash_update_p64(), it's not very much. Since
pmull_ghash_update_p8() will also need to be migrated into lib/crypto/
to achieve parity in the standalone GHASH support, let's move it into a
separate file ghash-neon-core.S.
Acked-by: Ard Biesheuvel <ardb@kernel.org>
Link: https://lore.kernel.org/r/20260319061723.1140720-7-ebiggers@kernel.org
Signed-off-by: Eric Biggers <ebiggers@kernel.org>
arch/arm/crypto/ghash-ce-glue.c originally provided only a "ghash"
crypto_shash algorithm using PMULL if available, else NEON.
Significantly later, it was updated to also provide a full AES-GCM
implementation using PMULL.
This made the PMULL support in the "ghash" crypto_shash largely
obsolete. Indeed, the arm64 equivalent of this file unconditionally
uses only ASIMD in its "ghash" crypto_shash.
Given that inconsistency and the fact that the NEON-only code is more
easily separable into the GHASH library than the PMULL based code is,
let's align with arm64 and just support NEON-only for the pure GHASH.
Acked-by: Ard Biesheuvel <ardb@kernel.org>
Link: https://lore.kernel.org/r/20260319061723.1140720-6-ebiggers@kernel.org
Signed-off-by: Eric Biggers <ebiggers@kernel.org>
Add GHASH support to the gf128hash module.
This will replace the GHASH support in the crypto_shash API. It will be
used by the "gcm" template and by the AES-GCM library (when an
arch-optimized implementation of the full AES-GCM is unavailable).
This consists of a simple API that mirrors the existing POLYVAL API, a
generic implementation of that API based on the existing efficient and
side-channel-resistant polyval_mul_generic(), and the framework for
architecture-optimized implementations of the GHASH functions.
The GHASH accumulator is stored in POLYVAL format rather than GHASH
format, since this is what most modern GHASH implementations actually
need. The few implementations that expect the accumulator in GHASH
format will just convert the accumulator to/from GHASH format
temporarily. (Supporting architecture-specific accumulator formats
would be possible, but doesn't seem worth the complexity.)
However, architecture-specific formats of struct ghash_key will be
supported, since a variety of formats will be needed there anyway. The
default format is just the key in POLYVAL format.
Acked-by: Ard Biesheuvel <ardb@kernel.org>
Link: https://lore.kernel.org/r/20260319061723.1140720-4-ebiggers@kernel.org
Signed-off-by: Eric Biggers <ebiggers@kernel.org>
Currently, some architectures (arm64 and x86) have optimized code for
both GHASH and POLYVAL. Others (arm, powerpc, riscv, and s390) have
optimized code only for GHASH. While POLYVAL support could be
implemented on these other architectures, until then we need to support
the case where arch-optimized functions are present only for GHASH.
Therefore, update the support for arch-optimized POLYVAL functions to
allow architectures to opt into supporting these functions individually.
The new meaning of CONFIG_CRYPTO_LIB_GF128HASH_ARCH is that some level
of GHASH and/or POLYVAL acceleration is provided.
Also provide an implementation of polyval_mul() based on
polyval_blocks_arch(), for when polyval_mul_arch() isn't implemented.
Acked-by: Ard Biesheuvel <ardb@kernel.org>
Link: https://lore.kernel.org/r/20260319061723.1140720-3-ebiggers@kernel.org
Signed-off-by: Eric Biggers <ebiggers@kernel.org>
Currently, the standalone GHASH code is coupled with crypto_shash. This
has resulted in unnecessary complexity and overhead, as well as the code
being unavailable to library code such as the AES-GCM library. Like was
done with POLYVAL, it needs to find a new home in lib/crypto/.
GHASH and POLYVAL are closely related and can each be implemented in
terms of each other. Optimized code for one can be reused with the
other. But also since GHASH tends to be difficult to implement directly
due to its unnatural bit order, most modern GHASH implementations
(including the existing arm, arm64, powerpc, and x86 optimized GHASH
code, and the new generic GHASH code I'll be adding) actually
reinterpret the GHASH computation as an equivalent POLYVAL computation,
pre and post-processing the inputs and outputs to map to/from POLYVAL.
Given this close relationship, it makes sense to group the GHASH and
POLYVAL code together in the same module. This gives us a wide range of
options for implementing them, reusing code between the two and properly
utilizing whatever instructions each architecture provides.
Thus, GHASH support will be added to the library module that is
currently called "polyval". Rename it to an appropriate name:
"gf128hash". Rename files, options, functions, etc. where appropriate
to reflect the upcoming sharing with GHASH. (Note: polyval_kunit is not
renamed, as ghash_kunit will be added alongside it instead.)
Acked-by: Ard Biesheuvel <ardb@kernel.org>
Link: https://lore.kernel.org/r/20260319061723.1140720-2-ebiggers@kernel.org
Signed-off-by: Eric Biggers <ebiggers@kernel.org>
All that's needed here is CRYPTO_HASH_INFO. It used to be the case that
CRYPTO_HASH_INFO was visible only when CRYPTO, but that was fixed by
commit aacb37f597 ("lib/crypto: hash_info: Move hash_info.c into
lib/crypto/"). Now CRYPTO_HASH_INFO can be selected directly.
Acked-by: Dan Williams <dan.j.williams@intel.com>
Link: https://lore.kernel.org/r/20251204055512.494013-1-ebiggers@kernel.org
Signed-off-by: Eric Biggers <ebiggers@kernel.org>
Given that tsm_mr_sample has a particular set of algorithms that it
wants, just use the library APIs for those algorithms rather than
crypto_shash. This is more straightforward and more efficient.
This also fixes a bug where this module failed to build if it was
enabled without CRYPTO_HASH happening to be set elsewhere in the
kconfig. (With the concurrent change to make TSM_MEASUREMENTS stop
selecting CRYPTO, this existing build error would have become easier to
encounter, as well.) Also, even if it built, crypto_alloc_shash() could
fail at runtime due to the needed algorithms not being available.
The library functions simply use direct linking. So if it builds, which
it will due to the kconfig options being selected, they are available.
Fixes: f6953f1f9e ("tsm-mr: Add tsm-mr sample code")
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Dan Williams <dan.j.williams@intel.com>
Link: https://lore.kernel.org/r/20260318164233.19800-1-ebiggers@kernel.org
Signed-off-by: Eric Biggers <ebiggers@kernel.org>
CONFIG_KERNEL_MODE_NEON is always enabled on arm64, and it always has
been since its introduction in 2013. Given that and the fact that the
usefulness of kernel-mode NEON has only been increasing over time,
checking for this option in arm64-specific code is unnecessary. Remove
these checks from lib/crypto/ to simplify the code and prevent any
future bugs where e.g. code gets disabled due to a typo in this logic.
Acked-by: Ard Biesheuvel <ardb@kernel.org>
Link: https://lore.kernel.org/r/20260314175049.26931-1-ebiggers@kernel.org
Signed-off-by: Eric Biggers <ebiggers@kernel.org>
For a short time this file was used by the SHA-256 and Poly1305 library
code, but they are no longer using it. Remove this unused file.
Acked-by: Ard Biesheuvel <ardb@kernel.org>
Link: https://lore.kernel.org/r/20260314173526.17349-1-ebiggers@kernel.org
Signed-off-by: Eric Biggers <ebiggers@kernel.org>
Defaulting the crypto KUnit tests to KUNIT_ALL_TESTS || CRYPTO_SELFTESTS
instead of simply KUNIT_ALL_TESTS was originally intended to make it
easy to enable all the crypto KUnit tests. This additional default is
nonstandard for KUnit tests, though, and it can cause all the KUnit
tests to be built-in unexpectedly if CRYPTO_SELFTESTS is set. It also
constitutes a back-reference to crypto/ from lib/crypto/, which is
something that we should be avoiding in order to get clean layering.
Now that we provide a lib/crypto/.kunitconfig file that enables all
crypto KUnit tests, let's consider that to be the supported way to
enable all these tests, and drop the default of CRYPTO_SELFTESTS.
Acked-by: Ard Biesheuvel <ardb@kernel.org>
Link: https://lore.kernel.org/r/20260317040626.5697-1-ebiggers@kernel.org
Signed-off-by: Eric Biggers <ebiggers@kernel.org>
The new option CONFIG_CRYPTO_LIB_ENABLE_ALL_FOR_KUNIT enables all the
crypto library code that has KUnit tests, causing CONFIG_KUNIT_ALL_TESTS
to enable all these tests. Add this option to all_tests.config so that
kunit.py will run them when passed the --alltests option.
Link: https://lore.kernel.org/r/20260314035927.51351-3-ebiggers@kernel.org
Signed-off-by: Eric Biggers <ebiggers@kernel.org>
For kunit.py to run all the crypto library tests when passed the
--alltests option, tools/testing/kunit/configs/all_tests.config needs to
enable options that satisfy the test dependencies.
This is the same as what lib/crypto/.kunitconfig already does.
However, the strategy that lib/crypto/.kunitconfig currently uses to
select all the hidden library options isn't going to scale up well when
it needs to be repeated in two places.
Instead let's go ahead and introduce an option
CRYPTO_LIB_ENABLE_ALL_FOR_KUNIT that depends on KUNIT and selects all
the crypto library options that have corresponding KUnit tests.
Update lib/crypto/.kunitconfig to use this option.
Link: https://lore.kernel.org/r/20260314035927.51351-2-ebiggers@kernel.org
Signed-off-by: Eric Biggers <ebiggers@kernel.org>
Make the jitterentropy RNG use the SHA-3 library API instead of
crypto_shash. This ends up being quite a bit simpler, as various
dynamic allocations and error checks become unnecessary.
Signed-off-by: David Howells <dhowells@redhat.com>
Co-developed-by: Eric Biggers <ebiggers@kernel.org>
Acked-by: Ard Biesheuvel <ardb@kernel.org>
Link: https://lore.kernel.org/r/20260226010005.43528-1-ebiggers@kernel.org
Signed-off-by: Eric Biggers <ebiggers@kernel.org>
Now that AES-CMAC has a library API, convert aes_s2v() to use it instead
of a "cmac(aes)" crypto_shash. The result is faster and simpler code.
It's also more reliable, since with the library the only step that can
fail is preparing the key. In contrast, crypto_shash_digest(),
crypto_shash_init(), crypto_shash_update(), and crypto_shash_final()
could all fail and return an errno value. aes_s2v() ignored these
errors, which was a bug. So that bug is fixed as well.
As part of this, change the prototype of aes_s2v() to take the raw key
directly instead of a prepared key. Its only two callers prepare a key
for each call, so it might as well be done directly in aes_s2v().
Since this removes the last dependency on the "cmac(aes)" crypto_shash
from mac80211, also remove the 'select CRYPTO_CMAC'.
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Reviewed-by: Ard Biesheuvel <ardb@kernel.org>
Link: https://lore.kernel.org/r/20260218213501.136844-16-ebiggers@kernel.org
Signed-off-by: Eric Biggers <ebiggers@kernel.org>
Now that AES-CMAC has a library API, convert the mac80211 AES-CMAC
packet authentication code to use it instead of a "cmac(aes)"
crypto_shash. This has multiple benefits, such as:
- It's faster. The AES-CMAC code is now called directly, without
unnecessary overhead such as indirect calls.
- MAC calculation can no longer fail.
- The AES-CMAC key struct is now a fixed size, allowing it to be
embedded directly into 'struct ieee80211_key' rather than using a
separate allocation. Note that although this increases the size of
the 'u.cmac' field of 'struct ieee80211_key', it doesn't cause it to
exceed the size of the largest variant of the union 'u'. Therefore,
the size of 'struct ieee80211_key' itself is unchanged.
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Reviewed-by: Ard Biesheuvel <ardb@kernel.org>
Link: https://lore.kernel.org/r/20260218213501.136844-15-ebiggers@kernel.org
Signed-off-by: Eric Biggers <ebiggers@kernel.org>
Add a FIPS cryptographic algorithm self-test for AES-CMAC to fulfill the
self-test requirement when this code is built into a FIPS 140
cryptographic module. This provides parity with the traditional crypto
API, which uses crypto/testmgr.c to meet the FIPS self-test requirement.
Reviewed-by: Ard Biesheuvel <ardb@kernel.org>
Link: https://lore.kernel.org/r/20260218213501.136844-8-ebiggers@kernel.org
Signed-off-by: Eric Biggers <ebiggers@kernel.org>
Instead of exposing the arm64-optimized CMAC, XCBC-MAC, and CBC-MAC code
via arm64-specific crypto_shash algorithms, instead just implement the
aes_cbcmac_blocks_arch() library function. This is much simpler, it
makes the corresponding library functions be arm64-optimized, and it
fixes the longstanding issue where this optimized code was disabled by
default. The corresponding algorithms still remain available through
crypto_shash, but individual architectures no longer need to handle it.
Note that to be compatible with the library using 'size_t' lengths, the
type of the return value and 'blocks' parameter to the assembly
functions had to be changed to 'size_t', and the assembly code had to be
updated accordingly to use the corresponding 64-bit registers.
Reviewed-by: Ard Biesheuvel <ardb@kernel.org>
Link: https://lore.kernel.org/r/20260218213501.136844-6-ebiggers@kernel.org
Signed-off-by: Eric Biggers <ebiggers@kernel.org>
To migrate the support for CBC-based MACs into libaes, the corresponding
arm64 assembly code needs to be moved there. However, the arm64 AES
assembly code groups many AES modes together; individual modes aren't
easily separable. (This isn't unique to arm64; other architectures
organize their AES modes similarly.)
Since the other AES modes will be migrated into the library eventually
too, just move the full assembly files for the AES modes into the
library. (This is similar to what I already did for PowerPC and SPARC.)
Specifically: move the assembly files aes-ce.S, aes-modes.S, and
aes-neon.S and their build rules; declare the assembly functions in
<crypto/aes.h>; and export the assembly functions from libaes.
Note that the exports and public declarations of the assembly functions
are temporary. They exist only to keep arch/arm64/crypto/ working until
the AES modes are fully moved into the library.
Reviewed-by: Ard Biesheuvel <ardb@kernel.org>
Link: https://lore.kernel.org/r/20260218213501.136844-5-ebiggers@kernel.org
Signed-off-by: Eric Biggers <ebiggers@kernel.org>
Since the 'enc_after' argument to neon_aes_mac_update() and
ce_aes_mac_update() has type 'int', it needs to be accessed using the
corresponding 32-bit register, not the 64-bit register. The upper half
of the corresponding 64-bit register may contain garbage.
Fixes: 4860620da7 ("crypto: arm64/aes - add NEON/Crypto Extensions CBCMAC/CMAC/XCBC driver")
Cc: stable@vger.kernel.org
Reviewed-by: Ard Biesheuvel <ardb@kernel.org>
Link: https://lore.kernel.org/r/20260218213501.136844-4-ebiggers@kernel.org
Signed-off-by: Eric Biggers <ebiggers@kernel.org>
Update the "aes" module to implement "cmac(aes)", "xcbc(aes)", and
"cbcmac(aes)" algorithms using the corresponding library functions, and
register these with the crypto_shash API. Each algorithm is included
only if the corresponding existing kconfig option is enabled.
This allows the architecture-optimized implementations of these
algorithms to continue to be accessible via the crypto_shash API once
they are migrated into the library.
For "xcbc(aes)", I also fixed the bug where AES key lengths other than
128 bits were allowed, so that this bug didn't have to be implemented in
the library. The AES-XCBC-MAC specification (RFC 3566) is clear that
key lengths other than 128 bits MUST NOT be supported. AES-XCBC-MAC
derives a 128-bit subkey internally, so the nonstandard support for
longer AES keys didn't really work: AES-128 was still used internally.
In the unlikely event that someone is actually relying on the broken and
nonstandard support for longer AES-XCBC-MAC keys, we can fairly easily
reintroduce it. But it seems unnecessary: the only user of "xcbc(aes)"
seems to be IPsec, which uses 128-bit keys with it.
Reviewed-by: Ard Biesheuvel <ardb@kernel.org>
Link: https://lore.kernel.org/r/20260218213501.136844-3-ebiggers@kernel.org
Signed-off-by: Eric Biggers <ebiggers@kernel.org>
Add support for CBC-based MACs to the AES library, specifically
AES-CMAC, AES-XCBC-MAC, and AES-CBC-MAC.
Of these three algorithms, AES-CMAC is the most modern and the most
commonly used. Use cases for the AES-CMAC library include the kernel's
SMB client and server, and the bluetooth and mac80211 drivers.
Support for AES-XCBC-MAC and AES-CBC-MAC is included so that there will
be no performance regression in the "xcbc(aes)" and "ccm(aes)" support
in the traditional crypto API once the arm64-optimized code is migrated
into the library. AES-XCBC-MAC is given its own key preparation
function but is otherwise identical to AES-CMAC and just reuses the
AES-CMAC structs and functions.
The implementation automatically uses the optimized AES key expansion
and single block en/decryption functions. It also allows architectures
to provide an optimized implementation of aes_cbcmac_blocks(), which
allows the existing arm64-optimized code for these modes to be used.
Just put the code for these modes directly in the libaes module rather
than in a separate module. This is simpler, it makes it easier to share
code between AES modes, and it increases the amount of inlining that is
possible. (Indeed, for these reasons, most of the
architecture-optimized AES code already provides multiple modes per
module. x86 for example has only a single aesni-intel module. So to a
large extent, this design choice just reflects the status quo.)
However, since there are a lot of AES modes, there's still some value in
omitting modes that are not needed at all in a given kernel. Therefore,
make these modes an optional feature of libaes, controlled by
CONFIG_CRYPTO_LIB_AES_CBC_MACS. This seems like a good middle ground.
Reviewed-by: Ard Biesheuvel <ardb@kernel.org>
Link: https://lore.kernel.org/r/20260218213501.136844-2-ebiggers@kernel.org
Signed-off-by: Eric Biggers <ebiggers@kernel.org>
Fix for the x86 EFI workaround keeping boot services code and data
regions reserved until after SetVirtualAddressMap() completes: deferred
struct page initialization may result in some of this memory to be lost
permanently.
-----BEGIN PGP SIGNATURE-----
iHUEABYKAB0WIQQQm/3uucuRGn1Dmh0wbglWLn0tXAUCaaxHtgAKCRAwbglWLn0t
XIbNAPwNjw/TSgVD+Ur//yqY7TxZSBari8aheEkXNaYHFCPImwD6A1CzNGn6rcka
JzeP+6HeOO9c0xCBudcR0aRfSma3cQI=
=a+XF
-----END PGP SIGNATURE-----
Merge tag 'efi-fixes-for-v7.0-2' of git://git.kernel.org/pub/scm/linux/kernel/git/efi/efi
Pull EFI fix from Ard Biesheuvel:
"Fix for the x86 EFI workaround keeping boot services code and data
regions reserved until after SetVirtualAddressMap() completes:
deferred struct page initialization may result in some of this memory
being lost permanently"
* tag 'efi-fixes-for-v7.0-2' of git://git.kernel.org/pub/scm/linux/kernel/git/efi/efi:
x86/efi: defer freeing of boot services memory
A revert for the i801 driver restoring old locking behaviour.
-----BEGIN PGP SIGNATURE-----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=Nc8b
-----END PGP SIGNATURE-----
Merge tag 'i2c-for-7.0-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux
Pull i2c fix from Wolfram Sang:
"A revert for the i801 driver restoring old locking behaviour"
* tag 'i2c-for-7.0-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
i2c: i801: Revert "i2c: i801: replace acpi_lock with I2C bus lock"
- Fix SEV guest boot failures in certain circumstances, due
to very early code relying on a BSS-zeroed variable that
isn't actually zeroed yet an may contain non-zero bootup
values. Move the variable into the .data section go gain
even earlier zeroing.
- Expose & allow the IBPB-on-Entry feature on SNP guests,
which was not properly exposed to guests due to initial
implementational caution.
- Fix O= build failure when CONFIG_EFI_SBAT_FILE is using
relative file paths.
- 4 commits to fix the various SNC (Sub-NUMA Clustering)
topology enumeration bugs/artifacts (sched-domain build
errors mostly). SNC enumeration data got more complicated
with Granite Rapids X (GNR) and Clearwater Forest X (CWF),
which exposed these bugs and made their effects more
serious.
- Also use the now sane(r) SNC code to fix resctrl SNC
detection bugs.
- Work around a historic libgcc unwinder bug in the vdso32
sigreturn code (again), which regressed during an overly
aggressive recent cleanup of DWARF annotations.
Signed-off-by: Ingo Molnar <mingo@kernel.org>
-----BEGIN PGP SIGNATURE-----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=KlDX
-----END PGP SIGNATURE-----
Merge tag 'x86-urgent-2026-03-08' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 fixes from Ingo Molnar:
- Fix SEV guest boot failures in certain circumstances, due to
very early code relying on a BSS-zeroed variable that isn't
actually zeroed yet an may contain non-zero bootup values
Move the variable into the .data section go gain even earlier
zeroing
- Expose & allow the IBPB-on-Entry feature on SNP guests, which
was not properly exposed to guests due to initial implementational
caution
- Fix O= build failure when CONFIG_EFI_SBAT_FILE is using relative
file paths
- Fix the various SNC (Sub-NUMA Clustering) topology enumeration
bugs/artifacts (sched-domain build errors mostly).
SNC enumeration data got more complicated with Granite Rapids X
(GNR) and Clearwater Forest X (CWF), which exposed these bugs
and made their effects more serious
- Also use the now sane(r) SNC code to fix resctrl SNC detection bugs
- Work around a historic libgcc unwinder bug in the vdso32 sigreturn
code (again), which regressed during an overly aggressive recent
cleanup of DWARF annotations
* tag 'x86-urgent-2026-03-08' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/entry/vdso32: Work around libgcc unwinder bug
x86/resctrl: Fix SNC detection
x86/topo: Fix SNC topology mess
x86/topo: Replace x86_has_numa_in_package
x86/topo: Add topology_num_nodes_per_package()
x86/numa: Store extra copy of numa_nodes_parsed
x86/boot: Handle relative CONFIG_EFI_SBAT_FILE file paths
x86/sev: Allow IBPB-on-Entry feature for SNP guests
x86/boot/sev: Move SEV decompressor variables into the .data section
permissive for auxiliary clocks, to not reject syscalls
based on the status field that do not try to modify the
status field. This makes ABI behavior in clock_adjtime()
consistent with CLOCK_REALTIME.
Signed-off-by: Ingo Molnar <mingo@kernel.org>
-----BEGIN PGP SIGNATURE-----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=zjov
-----END PGP SIGNATURE-----
Merge tag 'timers-urgent-2026-03-08' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull timer fix from Ingo Molnar:
"Make clock_adjtime() syscall timex validation slightly more permissive
for auxiliary clocks, to not reject syscalls based on the status field
that do not try to modify the status field.
This makes the ABI behavior in clock_adjtime() consistent with
CLOCK_REALTIME"
* tag 'timers-urgent-2026-03-08' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
timekeeping: Fix timex status validation for auxiliary clocks
PI and setscheduler() syscalls, resulting in kernel warnings
and misbehavior. Found during stress-testing.
Signed-off-by: Ingo Molnar <mingo@kernel.org>
-----BEGIN PGP SIGNATURE-----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=vP5l
-----END PGP SIGNATURE-----
Merge tag 'sched-urgent-2026-03-08' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull scheduler fix from Ingo Molnar:
"Fix a DL scheduler bug that may corrupt internal metrics during PI and
setscheduler() syscalls, resulting in kernel warnings and misbehavior.
Found during stress-testing"
* tag 'sched-urgent-2026-03-08' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
sched/deadline: Fix missing ENQUEUE_REPLENISH during PI de-boosting
Saves two function calls, and one stac/clac pair.
stac/clac is rather expensive on older cpus like Zen 2.
A synthetic network stress test gives a ~1.5% increase of pps
on AMD Zen 2.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Christophe Leroy <christophe.leroy@csgroup.eu>
Cc: Dave Hansen <dave.hansen@intel.com>
Cc: Kuniyuki Iwashima <kuniyu@google.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Two core changes and the rest in drivers, one core change to quirk the
behaviour of the Iomega Zip drive and one to fix a hang caused by tag
reallocation problems, which has mostly been seen by the iscsi client.
Note the latter fixes the problem but still has a slight sysfs memory
leak, so will be amended in the next pull request (once we've run the
fix for the fix through our testing).
Signed-off-by: James E.J. Bottomley <James.Bottomley@HansenPartnership.com>
-----BEGIN PGP SIGNATURE-----
iLgEABMIAGAWIQTnYEDbdso9F2cI+arnQslM7pishQUCaaxT0hsUgAAAAAAEAA5t
YW51MiwyLjUrMS4xMiwyLDImHGphbWVzLmJvdHRvbWxleUBoYW5zZW5wYXJ0bmVy
c2hpcC5jb20ACgkQ50LJTO6YrIVmDwD+P17JCAk+Ju0aNSnjEmIjUC2oI1S+9GdO
thbkK99vClABAOOkDvHopBBhfsilTpHBYjWFM34vC/iiaO/xfgd9YH2A
=kIDx
-----END PGP SIGNATURE-----
Merge tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI fixes from James Bottomley:
"Two core changes and the rest in drivers, one core change to quirk the
behaviour of the Iomega Zip drive and one to fix a hang caused by tag
reallocation problems, which has mostly been seen by the iscsi client.
Note the latter fixes the problem but still has a slight sysfs memory
leak, so will be amended in the next pull request (once we've run the
fix for the fix through our testing)"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
scsi: target: Fix recursive locking in __configfs_open_file()
scsi: devinfo: Add BLIST_SKIP_IO_HINTS for Iomega ZIP
scsi: mpi3mr: Clear reset history on ready and recheck state after timeout
scsi: core: Fix refcount leak for tagset_refcnt
Silence build error in au1100fb driver found by kernel test robot
-----BEGIN PGP SIGNATURE-----
iHUEABYKAB0WIQS86RI+GtKfB8BJu973ErUQojoPXwUCaayLiwAKCRD3ErUQojoP
X1pVAP4/j6LjBX862nFgtxS5XC4YBkpGRLYwO2WJMec+4sO5fQD/ThrowpuzZfPl
FhD/6WtMS4zPCDfNeqIKAo/JySez+w8=
=2Tha
-----END PGP SIGNATURE-----
Merge tag 'fbdev-for-7.0-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/deller/linux-fbdev
Pull fbdev fix from Helge Deller:
"Silence build error in au1100fb driver found by kernel test robot"
* tag 'fbdev-for-7.0-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/deller/linux-fbdev:
fbdev: au1100fb: Fix build on MIPS64
Three initial kernel mapping fixes
-----BEGIN PGP SIGNATURE-----
iHUEABYKAB0WIQS86RI+GtKfB8BJu973ErUQojoPXwUCaayE4AAKCRD3ErUQojoP
X4U4AQDtHPc9nlM3areu5yTQnOcPTExuEoIpvBm9ktwNCdrwCgEAt4tqv3hhxCvG
/lwb6XBCHfyw3d/AsTRbOIH1MGCnaQQ=
=itGt
-----END PGP SIGNATURE-----
Merge tag 'parisc-for-7.0-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/deller/parisc-linux
Pull parisc fixes from Helge Deller:
"While testing Sasha Levin's 'kallsyms: embed source file:line info in
kernel stack traces' patch series, which increases the typical kernel
image size, I found some issues with the parisc initial kernel mapping
which may prevent the kernel to boot.
The three small patches here fix this"
* tag 'parisc-for-7.0-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/deller/parisc-linux:
parisc: Fix initial page table creation for boot
parisc: Check kernel mapping earlier at bootup
parisc: Increase initial mapping to 64 MB with KALLSYMS
Fix a regression in RCU torture test pre-defined scenarios caused by
commit 7dadeaa6e8 ("sched: Further restrict the preemption modes")
which limits PREEMPT_NONE to architectures that do not support
preemption at all and PREEMPT_VOLUNTARY to those architectures that do
not yet have PREEMPT_LAZY support. Since major architectures (e.g. x86
and arm64) no longer support CONFIG_PREEMPT_NONE and
CONFIG_PREEMPT_VOLUNTARY, using them in rcutorture, rcuscale, refscale,
and scftorture pre-defined scenarios causes config checking errors.
Hence switch these kconfigs to PREEMPT_LAZY.
-----BEGIN PGP SIGNATURE-----
iQFFBAABCAAvFiEEj5IosQTPz8XU1wRHSXnow7UH+rgFAmmsZu0RHGJvcXVuQGtl
cm5lbC5vcmcACgkQSXnow7UH+rgNWwgAn1bIWDIWQR9CkRQ0grhdO+pPfLusbVg/
Y7H3SsdEX03meSunA/IVGejP6Qbanuab9nyHdv3WxxowpCGYBaLFPvklSfcBWYeZ
4lxi6Fj+2rrzvOnQ54Pk5i4v5VayxEo12XBIgx6HDV7+5LgWk0gU0LpWPUhEWYYR
z/zJ/XbcLr8e9tZVwAWZj/ShLUH301razC2SaR/OlS93zqRG9Sd251Knjqq/lEwI
T6RZfhT2Wz3bgqU3QcjxDWw5dhB0/Y9wKoJjx4bB9m8lnSt+o96gH40TO+lnllnS
T4OHjqK1J1fUXNLzQufyfKKAiwi/LBBc9H4pe4tiLFxg0fg5s21flQ==
=NBys
-----END PGP SIGNATURE-----
Merge tag 'rcu-fixes.v7.0-20260307a' of git://git.kernel.org/pub/scm/linux/kernel/git/rcu/linux
Pull RCU selftest fixes from Boqun Feng:
"Fix a regression in RCU torture test pre-defined scenarios caused by
commit 7dadeaa6e8 ("sched: Further restrict the preemption modes")
which limits PREEMPT_NONE to architectures that do not support
preemption at all and PREEMPT_VOLUNTARY to those architectures that do
not yet have PREEMPT_LAZY support.
Since major architectures (e.g. x86 and arm64) no longer support
CONFIG_PREEMPT_NONE and CONFIG_PREEMPT_VOLUNTARY, using them in
rcutorture, rcuscale, refscale, and scftorture pre-defined scenarios
causes config checking errors.
Switch these kconfigs to PREEMPT_LAZY"
* tag 'rcu-fixes.v7.0-20260307a' of git://git.kernel.org/pub/scm/linux/kernel/git/rcu/linux:
scftorture: Update due to x86 not supporting none/voluntary preemption
refscale: Update due to x86 not supporting none/voluntary preemption
rcuscale: Update due to x86 not supporting none/voluntary preemption
rcutorture: Update due to x86 not supporting none/voluntary preemption
- Fix possible NULL pointer dereference in trace_data_alloc()
On the error path in trace_data_alloc(), it can call trigger_data_free()
with a NULL pointer. This use to be a kfree() but was changed to
trigger_data_free() to clean up any partial initialization. The issue is
that trigger_data_free() does not expect a NULL pointer. Have
trigger_data_free() return safely on NULL pointer.
- Fix multiple events on the command line and bootconfig
If multiple events are enabled on the command line separately and not
grouped, only the last event gets enabled. That is:
trace_event=sched_switch trace_event=sched_waking
Will only enable sched_waking where as:
trace_event=sched_switch,sched_waking
Will enable both.
The bootconfig makes it even worse as the second way is the more common
method.
The issue is that a temporary buffer is used to store the events to enable
later in boot. Each time the cmdline callback is called, it overwrites
what was previously there.
Have the callback append the next value (delimited by a comma) if the
temporary buffer already has content.
- Fix command line trace_buffer_size if >= 2G
The logic to allocate the trace buffer uses "int" for the size parameter
in the command line code causing overflow issues if more that 2G is
specified.
-----BEGIN PGP SIGNATURE-----
iIoEABYKADIWIQRRSw7ePDh/lE+zeZMp5XQQmuv6qgUCaaxEIRQccm9zdGVkdEBn
b29kbWlzLm9yZwAKCRAp5XQQmuv6qn+QAQCM6aJm0ZqDD2dM262M1mQpkU7sW3Dz
hZfBpo3YlH55fQEAklsaD96+yKN7PLl1Vh4c0zCelMHZA7kgck/3GqaFAgA=
=rn/Z
-----END PGP SIGNATURE-----
Merge tag 'trace-v7.0-rc2-2' of git://git.kernel.org/pub/scm/linux/kernel/git/trace/linux-trace
Pull tracing fixes from Steven Rostedt:
- Fix possible NULL pointer dereference in trace_data_alloc()
On the trace_data_alloc() error path, it can call trigger_data_free()
with a NULL pointer. This used to be a kfree() but was changed to
trigger_data_free() to clean up any partial initialization. The issue
is that trigger_data_free() does not expect a NULL pointer. Have
trigger_data_free() return safely on NULL pointer.
- Fix multiple events on the command line and bootconfig
If multiple events are enabled on the command line separately and not
grouped, only the last event gets enabled. That is:
trace_event=sched_switch trace_event=sched_waking
will only enable sched_waking whereas:
trace_event=sched_switch,sched_waking
will enable both.
The bootconfig makes it even worse as the second way is the more
common method.
The issue is that a temporary buffer is used to store the events to
enable later in boot. Each time the cmdline callback is called, it
overwrites what was previously there.
Have the callback append the next value (delimited by a comma) if the
temporary buffer already has content.
- Fix command line trace_buffer_size if >= 2G
The logic to allocate the trace buffer uses "int" for the size
parameter in the command line code causing overflow issues if more
that 2G is specified.
* tag 'trace-v7.0-rc2-2' of git://git.kernel.org/pub/scm/linux/kernel/git/trace/linux-trace:
tracing: Fix trace_buf_size= cmdline parameter with sizes >= 2G
tracing: Fix enabling multiple events on the kernel command line and bootconfig
tracing: Add NULL pointer check to trigger_data_free()
The "|| echo -lzstd" default makes zstd an unconditional link
dependency of resolve_btfids. On systems where libzstd-dev is not
installed and pkg-config fails, the linker fails:
ld: cannot find -lzstd: No such file or directory
libzstd is a transitive dependency of libelf, so the -lzstd flag is
strictly necessary only for static builds [1].
Remove ZSTD_LIBS variable, and instead set LIBELF_LIBS depending on
whether the build is static or not. Use $(HOSTPKG_CONFIG) as primary
source of the flags list.
Also add a default value for HOSTPKG_CONFIG in case it's not built via
the toplevel Makefile. Pass it from selftests/bpf too.
[1] https://lore.kernel.org/bpf/4ff82800-2daa-4b9f-95a9-6f512859ee70@linux.dev/
Reported-by: BPF CI Bot (Claude Opus 4.6) <bot+bpf-ci@kernel.org>
Reported-by: Vitaly Chikunov <vt@altlinux.org>
Closes: https://lore.kernel.org/bpf/aaWqMcK-2AQw5dx8@altlinux.org/
Fixes: 4021848a90 ("selftests/bpf: Pass through build flags to bpftool and resolve_btfids")
Signed-off-by: Ihor Solodrai <ihor.solodrai@linux.dev>
Reviewed-by: Paul Chaignon <paul.chaignon@gmail.com>
Link: https://lore.kernel.org/r/20260305014730.3123382-1-ihor.solodrai@linux.dev
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
- aht10: Fix initialization commands for AHT20
- emc1403: correct a malformed email address
- it87: Check the it87_lock() return value
- max6639: fix inverted polarity
- macsmc: Fix overflows, underflows, sign extension, and other problems
- pmbus/q54sj108a2: fix stack overflow in debugfs read
- Drop support for SMARC-sAM67 (discontinued and never released to market)
-----BEGIN PGP SIGNATURE-----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=+l89
-----END PGP SIGNATURE-----
Merge tag 'hwmon-for-v7.0-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging
Pull hwmon fixes from Guenter Roeck:
- Fix initialization commands for AHT20
- Correct a malformed email address (emc1403)
- Check the it87_lock() return value
- Fix inverted polarity (max6639)
- Fix overflows, underflows, sign extension, and other problems in
macsmc
- Fix stack overflow in debugfs read (pmbus/q54sj108a2)
- Drop support for SMARC-sAM67 (discontinued and never released to
market)
* tag 'hwmon-for-v7.0-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging:
hwmon: (pmbus/q54sj108a2) fix stack overflow in debugfs read
hwmon: (max6639) fix inverted polarity
dt-bindings: hwmon: sl28cpld: Drop sa67mcu compatible
hwmon: (it87) Check the it87_lock() return value
Revert "hwmon: add SMARC-sAM67 support"
hwmon: (aht10) Fix initialization commands for AHT20
hwmon: (emc1403) correct a malformed email address
hwmon: (macsmc) Fix overflows, underflows, and sign extension
hwmon: (macsmc) Fix regressions in Apple Silicon SMC hwmon driver
- Revert "driver core: enforce device_lock for driver_match_device()":
When a device is already present in the system and a driver is
registered on the same bus, we iterate over all devices registered on
this bus to see if one of them matches. If we come across an already
bound one where the corresponding driver crashed while holding the
device lock (e.g. in probe()) we can't make any progress anymore.
Thus, revert and clarify that an implementer of struct bus_type must
not expect match() to be called with the device lock held.
-----BEGIN PGP SIGNATURE-----
iHUEABYKAB0WIQS2q/xV6QjXAdC7k+1FlHeO1qrKLgUCaawGIAAKCRBFlHeO1qrK
LmYsAP0XzV/dZVrEqU5AvchbcuZ7kfAKotj4wPUIAkoT3gzMcQEAqNm7Vaf2ulDs
CS8XvRi0PX6inD1Oo3dqwb0rKjKfFwY=
=GT+5
-----END PGP SIGNATURE-----
Merge tag 'driver-core-7.0-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/driver-core/driver-core
Pull driver core fix from Danilo Krummrich:
- Revert "driver core: enforce device_lock for driver_match_device()":
When a device is already present in the system and a driver is
registered on the same bus, we iterate over all devices registered on
this bus to see if one of them matches. If we come across an already
bound one where the corresponding driver crashed while holding the
device lock (e.g. in probe()) we can't make any progress anymore.
Thus, revert and clarify that an implementer of struct bus_type must
not expect match() to be called with the device lock held.
* tag 'driver-core-7.0-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/driver-core/driver-core:
Revert "driver core: enforce device_lock for driver_match_device()"
-----BEGIN PGP SIGNATURE-----
iJEEABYKADkWIQRTLbB6QfY48x44uB6AXGG7T9hjvgUCaav3pBsUgAAAAAAEAA5t
YW51MiwyLjUrMS4xMSwyLDIACgkQgFxhu0/YY75xWwD+NO/7WX01zcYSFMHTjHRx
okbOkBwFzcZK+p/L4iTtVv0BAIYPUpa+RBLR2RtYN7mQEw8KO5yVgiLP2nlQYwIf
wZcH
=DrUe
-----END PGP SIGNATURE-----
Merge tag 'for-linus-7.0-rc3-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip
Pull xen fixes from Juergen Gross:
- a cleanup of arch/x86/kernel/head_64.S removing the pre-built page
tables for Xen guests
- a small comment update
- another cleanup for Xen PVH guests mode
- fix an issue with Xen PV-devices backed by driver domains
* tag 'for-linus-7.0-rc3-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip:
xen/xenbus: better handle backend crash
xenbus: add xenbus_device parameter to xenbus_read_driver_state()
x86/PVH: Use boot params to pass RSDP address in start_info page
x86/xen: update outdated comment
xen/acpi-processor: fix _CST detection using undersized evaluation buffer
x86/xen: Build identity mapping page tables dynamically for XENPV
Eduard Zingerman says:
====================
bpf: Fix precision backtracking bug with linked registers
Emil Tsalapatis reported a verifier bug hit by the scx_lavd sched_ext
scheduler. The essential part of the verifier log looks as follows:
436: ...
// checkpoint hit for 438: (1d) if r7 == r8 goto ...
frame 3: propagating r2,r7,r8
frame 2: propagating r6
mark_precise: frame3: last_idx ...
mark_precise: frame3: regs=r2,r7,r8 stack= before 436: ...
mark_precise: frame3: regs=r2,r7 stack= before 435: ...
mark_precise: frame3: regs=r2,r7 stack= before 434: (85) call bpf_trace_vprintk#177
verifier bug: backtracking call unexpected regs 84
The log complains that registers r2 and r7 are tracked as precise
while processing the bpf_trace_vprintk() call in precision backtracking.
This can't be right, as r2 is reset by the call and there is nothing
to backtrack it to. The precision propagation is triggered when
a checkpoint is hit at instruction 438, r2 is dead at that instruction.
This happens because of the following sequence of events:
- Instruction 438 is first reached with registers r2 and r7 having
the same id via a path that does not call bpf_trace_vprintk():
- Checkpoint is created at 438.
- The jump at 438 is predicted, hence r7 and registers linked to it
(r2) are propagated as precise, marking r2 and r7 precise in the
checkpoint.
- Instruction 438 is reached a second time with r2 undefined and via
a path that calls bpf_trace_vprintk():
- Checkpoint is hit.
- propagate_precision() picks registers r2 and r7 and propagates
precision marks for those up to the helper call.
The root cause is the fact that states_equal() and
propagate_precision() assume that the precision flag can't be set for a
dead register (as computed by compute_live_registers()).
However, this is not the case when linked registers are at play.
Fix this by accounting for live register flags in
collect_linked_regs().
---
====================
Link: https://patch.msgid.link/20260306-linked-regs-and-propagate-precision-v1-0-18e859be570d@gmail.com
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Add a test for the scenario described in the previous commit:
an iterator loop with two paths where one ties r2/r7 via
shared scalar id and skips a call, while the other goes
through the call. Precision marks from the linked registers
get spuriously propagated to the call path via
propagate_precision(), hitting "backtracking call unexpected
regs" in backtrack_insn().
Signed-off-by: Eduard Zingerman <eddyz87@gmail.com>
Link: https://lore.kernel.org/r/20260306-linked-regs-and-propagate-precision-v1-2-18e859be570d@gmail.com
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
