Update dt-bindings to add primary controller of QCS615 to USB
DWC3 controller list.
Although this controller has a QUSB2 Phy, it belongs to a
generation of SoCs like SDM670/SDM845/SM6350 where DP/DM is
used for wakeup instead of qusb2_phy interrupt.
Signed-off-by: Krishna Kurapati <krishna.kurapati@oss.qualcomm.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20241224084621.4139021-2-krishna.kurapati@oss.qualcomm.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This is to correct the mistaken byte offset of the field bDeviceClass in
OP_REP_IMPORT documentation. The previous field bcdDevice has length 2 and
the offset for bDeviceClass should be 0x138 + 2 = 0x13A instead of 0x139.
Offsets for subsequent fields are also affected and fixed in this patch.
Signed-off-by: Gordon Ou <gordon.xwj@gmail.com>
Reviewed-by: Shuah Khan <skhan@linuxfoundation.org>
Link: https://lore.kernel.org/r/20241224062336.63215-1-gordon.xwj@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
xHC hosts can pass 24 bits of data with a command completion event TRB
as the completion code only uses 8 bits of the 32 bit status field.
Only Configure Endpoint, and Get Extended Property commands utilize
this "command completion parameter" 24 bit field.
For other command completion events the xHC should keep it RsvdZ.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20241227120142.1035206-5-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If a command is queued to the final usable TRB of a ring segment, the
enqueue pointer is advanced to the subsequent link TRB and no further.
If the command is later aborted, when the abort completion is handled
the dequeue pointer is advanced to the first TRB of the next segment.
If no further commands are queued, xhci_handle_stopped_cmd_ring() sees
the ring pointers unequal and assumes that there is a pending command,
so it calls xhci_mod_cmd_timer() which crashes if cur_cmd was NULL.
Don't attempt timer setup if cur_cmd is NULL. The subsequent doorbell
ring likely is unnecessary too, but it's harmless. Leave it alone.
This is probably Bug 219532, but no confirmation has been received.
The issue has been independently reproduced and confirmed fixed using
a USB MCU programmed to NAK the Status stage of SET_ADDRESS forever.
Everything continued working normally after several prevented crashes.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=219532
Fixes: c311e391a7 ("xhci: rework command timeout and cancellation,")
CC: stable@vger.kernel.org
Signed-off-by: Michal Pecio <michal.pecio@gmail.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20241227120142.1035206-4-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Improve dbc transfer rate performance by copying the received data to
the tty buffer directly in the request complete callback function if
possible.
Only defer it in case there is already pending deferred work, tty is
throttled, or we fail copy the data to the tty buffer
The request complete callback is already called by a workqueue.
This is part 3/3 of a dbc performance improvement series that roughly
triples dbc performace when using adb push and pull over dbc.
Max/min push rate after patches is 210/118 MB/s, pull rate 171/133 MB/s,
tested with large files (300MB-9GB) by Łukasz Bartosik
Cc: Łukasz Bartosik <ukaszb@chromium.org>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20241227120142.1035206-3-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Queue event polling work with 0 delay in case there are pending transfers
queued up. This is part 2 of a 3 part series that roughly triples dbc
performace when using adb push and pull over dbc.
Max/min push rate after patches is 210/118 MB/s, pull rate 171/133 MB/s,
tested with large files (300MB-9GB) by Łukasz Bartosik
First performance improvement patch was commit 31128e7492
("xhci: dbc: add dbgtty request to end of list once it completes")
Cc: Łukasz Bartosik <ukaszb@chromium.org>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20241227120142.1035206-2-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Set TARGET_SCF_ACK_KREF flag and allow f_tcm to take the BOT command
reference. A usb request may be canceled, the f_tcm knows this. Let it
decides if the command should be freed. This is the same as how the UAS
interface is done.
Signed-off-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/e791c639e91b5d91a8787f5d6902e8c58f1dc172.1733876548.git.Thinh.Nguyen@synopsys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Handle target_core_fabric_ops TASK MANAGEMENT functions and their
response. If a TASK MANAGEMENT command is received, the driver will
interpret the function TMF_*, translate to TMR_*, and fire off a command
work executing target_submit_tmr(). On completion, it will handle the
TASK MANAGEMENT response through uasp_send_tm_response().
Signed-off-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/50339586e36509dadb9c208b3314530993e673b6.1733876548.git.Thinh.Nguyen@synopsys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If the transfer is cancelled due to a disconnect or driver tear down
(error code -ESHUTDOWN), then just free the command. However, if it got
cancelled due to other reasons, then send a sense CHECK CONDITION status
with TCM_CHECK_CONDITION_ABORT_CMD status to host notifying the delivery
failure. Note that this is separate from TASK MANAGEMENT function abort
task command, which will require a separate response IU.
See UAS-r04 section 8.
Signed-off-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/f2ae293c1fc39df4d242a2f724584bf4ec105ece.1733876548.git.Thinh.Nguyen@synopsys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There may be different reasons for the transfer to be cancelled. Don't
blindly free the command without checking its status. We may still need
to properly respond to cancelled command. Check and only free the
command on endpoint disable.
Signed-off-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/6c4ae2b4c2a9037bdcb6f909e173a94b11f04657.1733876548.git.Thinh.Nguyen@synopsys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Don't just wait for the data write completion and execute the target
command. We need to verify if the request completed successfully and not
just sending invalid data. The verification is done in the write request
completion routine. Queue the same work of the command to execute the
target_execute_cmd() on data write.
Signed-off-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/9f6b1c6946cf49eeba0173e405678b9b7786636b.1733876548.git.Thinh.Nguyen@synopsys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
To properly respond to host sending more commands than the number of
streams the device advertises, the device needs to be able to reject the
command with a response. Allocate an extra request to handle 1 more
command than the number of streams.
Signed-off-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/256f2ec8f5e042ab692d9593144fa75f3d3ce94b.1733876548.git.Thinh.Nguyen@synopsys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Resubmit command on completion to fetch more commands and service them
in parallel. Increase the number of work in a queue. Each work will be
for each command allowing them to be processed concurrently. Also, set
them to be unbounded by cpu to improve performance.
Signed-off-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/933cf7191b672bf4cfbea4df19af1b08dc1baca9.1733876548.git.Thinh.Nguyen@synopsys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We can handle multiple commands concurently. Each command services a
stream id. At the moment, the driver will handle 32 outstanding streams,
which is equivalent to 32 commands. Make sure to allocate a matching
number of commands to the number of streams.
Signed-off-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/2d806120dcc10c88fef21865b7bc1d2b6604fe42.1733876548.git.Thinh.Nguyen@synopsys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Host can assign stream ID value greater than number of streams
allocated. The tcm function needs to keep track of which stream is
available to assign the stream ID. This patch doesn't track that, but at
least it makes sure that there's no Oops if the host send tag with a
value greater than the number of supported streams.
Signed-off-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/d57b7dfd228199cef811206b1b83ec649f742752.1733876548.git.Thinh.Nguyen@synopsys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Only allocate up to UASP_SS_EP_COMP_NUM_STREAMS number of session tags.
We should not be using more than UASP_SS_EP_COMP_NUM_STREAMS of tags due
to the number of commands limit we imposed. Each command uses a unique
tag. Any more than that is unnecessary. By limiting it, we can detect an
issue in our driver immediately should we run out of session tags.
Signed-off-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/017016ffcab2f3c284d863fc42483b83dbd21b35.1733876548.git.Thinh.Nguyen@synopsys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently the default bMaxBurst is 0. Set default bMaxBurst to 15 (i.e.
16 bursts) to Data IN and OUT endpoints to improve performance. It
should be fine for a controller that supports less than 16 bursts. It
should be able to negotiate properly with the host at packet level for
the end of burst.
If the controller can't handle a burst of 16, and high performance isn't
important, the user can use BOT protocol from mass_storage gadget driver
instead.
Signed-off-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/9d6265db4d138e542f281988362bc4392b034d43.1733876548.git.Thinh.Nguyen@synopsys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some old builds of Microsoft Windows 10 UASP class driver reject UASP
device with stream count of 2^4. To keep compatibility with both Linux
and Windows, let's increase the stream count to 2^5. Also, internal
tests show that stream count of 2^5 increases performance slightly.
Signed-off-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/23bf7f5cb04da691fd6ba0a77babee9ad3195f44.1733876548.git.Thinh.Nguyen@synopsys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Altmodes with cros_ec are either automatically entered by the EC or
entered by the AP if TBT or USB4 are supported on the system. Due to the
security risk of PCIe tunneling, TBT modes should not be auto entered by
the kernel at this time and will require user intervention.
With this change, a userspace program will need to explicitly activate
the thunderbolt mode on the port and partner in order to enter the mode
and the thunderbolt driver will not automatically enter when a partner
is connected.
Signed-off-by: Abhishek Pandit-Subedi <abhishekpandit@chromium.org>
Reviewed-by: Benson Leung <bleung@chromium.org>
Link: https://lore.kernel.org/r/20241213153543.v5.8.Ic14738918e3d026fa2d85e95fb68f8e07a0828d0@changeid
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Mux configuration is often the final piece of mode entry and can be used
to determine whether a partner altmode is active. When mux configuration
is done, use the active port altmode's SVID to set the partner active
field for all partner alt modes.
Signed-off-by: Abhishek Pandit-Subedi <abhishekpandit@chromium.org>
Reviewed-by: Benson Leung <bleung@chromium.org>
Link: https://lore.kernel.org/r/20241213153543.v5.5.I083bf9188947be8cb7460211cfdf3233370a28f6@changeid
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The active property of port altmode should be writable (to prevent or
allow partner altmodes from entering) and needs to be part of
typec_altmode_desc so we can initialize the port to an inactive state if
desired.
Signed-off-by: Abhishek Pandit-Subedi <abhishekpandit@chromium.org>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Reviewed-by: Benson Leung <bleung@chromium.org>
Link: https://lore.kernel.org/r/20241213153543.v5.3.I794566684ab2965e209f326b08232006eff333f8@changeid
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Mode in struct typec_altmode is used to indicate the index of the
altmode on a port, partner or plug. It is used in enter mode VDMs but
doesn't make much sense for matching against altmode drivers or for
matching partner to port altmodes.
Signed-off-by: Abhishek Pandit-Subedi <abhishekpandit@chromium.org>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Reviewed-by: Benson Leung <bleung@chromium.org>
Link: https://lore.kernel.org/r/20241213153543.v5.1.Ie0d37646f18461234777d88b4c3e21faed92ed4f@changeid
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The UDC state in sysfs (/sys/class/udc/<udc>/state) should accurately
reflect the current state of the USB Device Controller.
Currently, the UDC state is not handled consistently during gadget
disconnection. While the disconnect interrupt path correctly sets the
state to "not-attached", manual deconfiguration leaves the state in
"configured", misrepresenting the actual situation.
This commit ensures consistent UDC state handling by setting the state to
"not-attached" after manual deconfiguration. This accurately reflects the
UDC's state and provides a consistent behavior regardless of the
disconnection method.
Signed-off-by: Roy Luo <royluo@google.com>
Reviewed-by: André Draszik <andre.draszik@linaro.org>
Tested-by: André Draszik <andre.draszik@linaro.org>
Link: https://lore.kernel.org/r/20241223042536.1465299-1-royluo@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The sysfs core now allows instances of 'struct bin_attribute' to be
moved into read-only memory. Make use of that to protect them against
accidental or malicious modifications.
Signed-off-by: Thomas Weißschuh <linux@weissschuh.net>
Link: https://lore.kernel.org/r/20241222-sysfs-const-bin_attr-usbip-v1-1-20d611a9bfa4@weissschuh.net
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The sysfs core now allows instances of 'struct bin_attribute' to be
moved into read-only memory. Make use of that to protect them against
accidental or malicious modifications.
Signed-off-by: Thomas Weißschuh <linux@weissschuh.net>
Link: https://lore.kernel.org/r/20241222-sysfs-const-bin_attr-usb-v1-1-19a137c0f20a@weissschuh.net
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fixes issue where memory will fail to be allocated for larger bulk
transfers, ~1 MB or more. This occurs because userland libraries, such
as libusb, send the entire USB data buffer when SG support is detected.
The assumption is that the driver knows how to properly split the data
up before sending it out.
By hardcoding a limit, bigger transfers that exceed the SG tablesize
limit of 32 will be unable to use SG. This results in an attempt to
allocate contiguous pages which, unsurprisingly, will fail too and
returns an ENOMEM. It looks like other drivers that support SG allow for
any length of SG lists. Accepting any SG size allows the driver to
properly handle large bulk transfer situations.
Tested bulk read and write operations using the following devices:
- Logitech Webcam Pro 9000 - USB 2.0
- SanDisk Ultra - USB 3.0
- Logitech M500s Mouse
Signed-off-by: Jason Long <jasonlongball@gmail.com>
Reviewed-by: Shuah Khan <skhan@linuxfoundation.org>
Link: https://lore.kernel.org/r/20241218161344.202637-1-jasonlongball@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This commit adds a new AMS for responding to a "Get_Revision" request.
Revision message consists of the following fields:
+----------------------------------------------------+
| Header | RMDO |
| No. of data objects = 1 | |
+----------------------------------------------------+
While RMDO consists of:
* B31..28 Revision Major
* B27..24 Revision Minor
* B23..20 Version Major
* B19..16 Version Minor
* B15..0 Reserved, shall be set to zero.
As per the PD spec ("8.3.3.16.2.1 PR_Give_Revision State"), a request is
only expected when an explicit contract is established and the port is
in ready state. This AMS is only supported for PD >= 3.0.
Signed-off-by: Amit Sunil Dhamne <amitsd@google.com>
Reviewed-by: Badhri Jagan Sridharan <badhri@google.com>
Link: https://lore.kernel.org/r/20241210-get_rev_upstream-v2-3-d0094e52d48f@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add support for parsing "pd-revision" DT property in TCPM and store PD
revision and version supported by the Type-C connnector.
It should be noted that the PD revision is the maximum possible revision
supported by the port. This is different from the 2 bit revision set in
PD msg headers. The purpose of the 2 bit revision value is to negotiate
between Rev 2.X & 3.X spec rev as part of contract negotiation, while
this is used for Get_Revision AMS after a contract is in place.
Signed-off-by: Amit Sunil Dhamne <amitsd@google.com>
Reviewed-by: Badhri Jagan Sridharan <badhri@google.com>
Link: https://lore.kernel.org/r/20241210-get_rev_upstream-v2-2-d0094e52d48f@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>