[ Upstream commit 56c17ee151 ]
The file descriptor opened in isolate_cpus() when (!level) is true was
not being closed before returning, causing a file descriptor leak in
both the error path and the success path.
When write() fails at line 950, the function returns at line 953 without
closing the file descriptor. Similarly, on success, the function returns
at line 956 without closing the file descriptor.
Add close(fd) calls before both return statements to fix the resource
leak. This follows the same pattern used elsewhere in the same function
where file descriptors are properly closed before returning (see lines
1005 and 1027).
Fixes: 997074df65 ("tools/power/x86/intel-speed-select: Use cgroup v2 isolation")
Signed-off-by: Malaya Kumar Rout <mrout@redhat.com>
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7874eeacfa ]
The commit e1168f0 ("RDMA/iwcm: Simplify cm_event_handler()")
changed the work submission logic to unconditionally call
queue_work() with the expectation that queue_work() would
have no effect if work was already pending. The problem is
that a free list of struct iwcm_work is used (for which
struct work_struct is embedded), so each call to queue_work()
is basically unique and therefore does indeed queue the work.
This causes a problem in the work handler which walks the work_list
until it's empty to process entries. This means that a single
run of the work handler could process item N+1 and release it
back to the free list while the actual workqueue entry is still
queued. It could then get reused (INIT_WORK...) and lead to
list corruption in the workqueue logic.
Fix this by just removing the work_list. The workqueue already
does this for us.
This fixes the following error that was observed when stress
testing with ucmatose on an Intel E830 in iWARP mode:
[ 151.465780] list_del corruption. next->prev should be ffff9f0915c69c08, but was ffff9f0a1116be08. (next=ffff9f0a15b11c08)
[ 151.466639] ------------[ cut here ]------------
[ 151.466986] kernel BUG at lib/list_debug.c:67!
[ 151.467349] Oops: invalid opcode: 0000 [#1] SMP NOPTI
[ 151.467753] CPU: 14 UID: 0 PID: 2306 Comm: kworker/u64:18 Not tainted 6.19.0-rc4+ #1 PREEMPT(voluntary)
[ 151.468466] Hardware name: QEMU Ubuntu 24.04 PC (i440FX + PIIX, 1996), BIOS 1.16.3-debian-1.16.3-2 04/01/2014
[ 151.469192] Workqueue: 0x0 (iw_cm_wq)
[ 151.469478] RIP: 0010:__list_del_entry_valid_or_report+0xf0/0x100
[ 151.469942] Code: c7 58 5f 4c b2 e8 10 50 aa ff 0f 0b 48 89 ef e8 36 57 cb ff 48 8b 55 08 48 89 e9 48 89 de 48 c7 c7 a8 5f 4c b2 e8 f0 4f aa ff <0f> 0b 66 2e 0f 1f 84 00 00 00 00 00 0f 1f 40 00 90 90 90 90 90 90
[ 151.471323] RSP: 0000:ffffb15644e7bd68 EFLAGS: 00010046
[ 151.471712] RAX: 000000000000006d RBX: ffff9f0915c69c08 RCX: 0000000000000027
[ 151.472243] RDX: 0000000000000000 RSI: 0000000000000000 RDI: ffff9f0a37d9c600
[ 151.472768] RBP: ffff9f0a15b11c08 R08: 0000000000000000 R09: c0000000ffff7fff
[ 151.473294] R10: 0000000000000001 R11: ffffb15644e7bba8 R12: ffff9f092339ee68
[ 151.473817] R13: ffff9f0900059c28 R14: ffff9f092339ee78 R15: 0000000000000000
[ 151.474344] FS: 0000000000000000(0000) GS:ffff9f0a847b5000(0000) knlGS:0000000000000000
[ 151.474934] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[ 151.475362] CR2: 0000559e233a9088 CR3: 000000020296b004 CR4: 0000000000770ef0
[ 151.475895] PKRU: 55555554
[ 151.476118] Call Trace:
[ 151.476331] <TASK>
[ 151.476497] move_linked_works+0x49/0xa0
[ 151.476792] __pwq_activate_work.isra.46+0x2f/0xa0
[ 151.477151] pwq_dec_nr_in_flight+0x1e0/0x2f0
[ 151.477479] process_scheduled_works+0x1c8/0x410
[ 151.477823] worker_thread+0x125/0x260
[ 151.478108] ? __pfx_worker_thread+0x10/0x10
[ 151.478430] kthread+0xfe/0x240
[ 151.478671] ? __pfx_kthread+0x10/0x10
[ 151.478955] ? __pfx_kthread+0x10/0x10
[ 151.479240] ret_from_fork+0x208/0x270
[ 151.479523] ? __pfx_kthread+0x10/0x10
[ 151.479806] ret_from_fork_asm+0x1a/0x30
[ 151.480103] </TASK>
Fixes: e1168f09b3 ("RDMA/iwcm: Simplify cm_event_handler()")
Signed-off-by: Jacob Moroni <jmoroni@google.com>
Link: https://patch.msgid.link/20260112020006.1352438-1-jmoroni@google.com
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0beefd0e15 ]
In rxe_srq_from_init(), the queue pointer 'q' is assigned to
'srq->rq.queue' before copying the SRQ number to user space.
If copy_to_user() fails, the function calls rxe_queue_cleanup()
to free the queue, but leaves the now-invalid pointer in
'srq->rq.queue'.
The caller of rxe_srq_from_init() (rxe_create_srq) eventually
calls rxe_srq_cleanup() upon receiving the error, which triggers
a second rxe_queue_cleanup() on the same memory, leading to a
double free.
The call trace looks like this:
kmem_cache_free+0x.../0x...
rxe_queue_cleanup+0x1a/0x30 [rdma_rxe]
rxe_srq_cleanup+0x42/0x60 [rdma_rxe]
rxe_elem_release+0x31/0x70 [rdma_rxe]
rxe_create_srq+0x12b/0x1a0 [rdma_rxe]
ib_create_srq_user+0x9a/0x150 [ib_core]
Fix this by moving 'srq->rq.queue = q' after copy_to_user.
Fixes: aae0484e15 ("IB/rxe: avoid srq memory leak")
Signed-off-by: Jiasheng Jiang <jiashengjiangcool@gmail.com>
Link: https://patch.msgid.link/20260112015412.29458-1-jiashengjiangcool@gmail.com
Reviewed-by: Zhu Yanjun <yanjun.Zhu@linux.dev>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 83835f7c07 ]
This fixes the following error on the server side:
RTRS server session allocation failed: -EINVAL
caused by the caller of the `ib_dma_map_sg()`, which does not expect
less mapped entries, than requested, which is in the order of things
and can be easily reproduced on the machine with enabled IOMMU.
The fix is to treat any positive number of mapped sg entries as a
successful mapping and cache DMA addresses by traversing modified
SG table.
Fixes: 9cb8374804 ("RDMA/rtrs: server: main functionality")
Signed-off-by: Roman Penyaev <r.peniaev@gmail.com>
Signed-off-by: Jack Wang <jinpu.wang@ionos.com>
Signed-off-by: Grzegorz Prajsner <grzegorz.prajsner@ionos.com>
Link: https://patch.msgid.link/20260107161517.56357-2-haris.iqbal@ionos.com
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 39fe0eac6d ]
In `probe()`, `request_irq()` is called before allocating/registering a
`power_supply` handle. If an interrupt is fired between the call to
`request_irq()` and `power_supply_register()`, the `power_supply` handle
will be used uninitialized in `power_supply_changed()` in
`wm97xx_bat_update()` (triggered from the interrupt handler). This will
lead to a `NULL` pointer dereference since
Fix this racy `NULL` pointer dereference by making sure the IRQ is
requested _after_ the registration of the `power_supply` handle. Since
the IRQ is the last thing requests in the `probe()` now, remove the
error path for freeing it. Instead add one for unregistering the
`power_supply` handle when IRQ request fails.
Fixes: 7c87942aef ("wm97xx_battery: Use irq to detect charger state")
Signed-off-by: Waqar Hameed <waqar.hameed@axis.com>
Link: https://patch.msgid.link/97b55f0479a932eea7213844bf66f28a974e27a2.1766270196.git.waqar.hameed@axis.com
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 688364a116 ]
bq27xxx_write(), bq27xxx_read_block(), and bq27xxx_write_block()
return -EPERM when the bus callback pointer is NULL. A NULL callback
indicates the operation is not supported by the bus/driver,
not that permission is denied.
Return -EOPNOTSUPP instead of -EPERM when di->bus.write/
read_bulk/write_bulk is NULL.
Fixes: 14073f6614 ("power: supply: bq27xxx: Add bulk transfer bus methods")
Signed-off-by: Haotian Zhang <vulab@iscas.ac.cn>
Reviewed-by: Matt Ranostay <matt@ranostay.sg>
Link: https://patch.msgid.link/20251204083436.1367-1-vulab@iscas.ac.cn
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 36b0562922 ]
Some platforms expose reboot mode cells that are smaller than an
unsigned int, in which cases lead to write failures. Read the cell
first to determine actual size and only write the number of bytes the
cell can hold.
Fixes: 7a78a7f769 ("power: reset: nvmem-reboot-mode: use NVMEM as reboot mode write interface")
Signed-off-by: Alexander Koskovich <akoskovich@pm.me>
Link: https://patch.msgid.link/20251214191529.2470580-1-akoskovich@pm.me
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8d59cf3887 ]
Using the `devm_` variant for requesting IRQ _before_ the `devm_`
variant for allocating/registering the `power_supply` handle, means that
the `power_supply` handle will be deallocated/unregistered _before_ the
interrupt handler (since `devm_` naturally deallocates in reverse
allocation order). This means that during removal, there is a race
condition where an interrupt can fire just _after_ the `power_supply`
handle has been freed, *but* just _before_ the corresponding
unregistration of the IRQ handler has run.
This will lead to the IRQ handler calling `power_supply_changed()` with
a freed `power_supply` handle. Which usually crashes the system or
otherwise silently corrupts the memory...
Note that there is a similar situation which can also happen during
`probe()`; the possibility of an interrupt firing _before_ registering
the `power_supply` handle. This would then lead to the nasty situation
of using the `power_supply` handle *uninitialized* in
`power_supply_changed()`.
Fix this racy use-after-free by making sure the IRQ is requested _after_
the registration of the `power_supply` handle. Keep the old behavior of
just printing a warning in case of any failures during the IRQ request
and finishing the probe successfully.
Fixes: d2cec82c28 ("power: sbs-battery: Request threaded irq and fix dev callback cookie")
Signed-off-by: Waqar Hameed <waqar.hameed@axis.com>
Reviewed-by: Phil Reid <preid@electromag.com.au>
Link: https://patch.msgid.link/0ef896e002495e615157b482d18a437af19ddcd0.1766268280.git.waqar.hameed@axis.com
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e2febe375e ]
Using the `devm_` variant for requesting IRQ _before_ the `devm_`
variant for allocating/registering the `power_supply` handle, means that
the `power_supply` handle will be deallocated/unregistered _before_ the
interrupt handler (since `devm_` naturally deallocates in reverse
allocation order). This means that during removal, there is a race
condition where an interrupt can fire just _after_ the `power_supply`
handle has been freed, *but* just _before_ the corresponding
unregistration of the IRQ handler has run.
This will lead to the IRQ handler calling `power_supply_changed()` with
a freed `power_supply` handle. Which usually crashes the system or
otherwise silently corrupts the memory...
Note that there is a similar situation which can also happen during
`probe()`; the possibility of an interrupt firing _before_ registering
the `power_supply` handle. This would then lead to the nasty situation
of using the `power_supply` handle *uninitialized* in
`power_supply_changed()`.
Fix this racy use-after-free by making sure the IRQ is requested _after_
the registration of the `power_supply` handle.
Fixes: e86d69dd78 ("power_supply: Add support for Richtek RT9455 battery charger")
Signed-off-by: Waqar Hameed <waqar.hameed@axis.com>
Link: https://patch.msgid.link/1567d831e04c3e2fcb9e18dd36b7bcba4634581a.1766268280.git.waqar.hameed@axis.com
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b750812997 ]
Using the `devm_` variant for requesting IRQ _before_ the `devm_`
variant for allocating/registering the `power_supply` handle, means that
the `power_supply` handle will be deallocated/unregistered _before_ the
interrupt handler (since `devm_` naturally deallocates in reverse
allocation order). This means that during removal, there is a race
condition where an interrupt can fire just _after_ the `power_supply`
handle has been freed, *but* just _before_ the corresponding
unregistration of the IRQ handler has run.
This will lead to the IRQ handler calling `power_supply_changed()` with
a freed `power_supply` handle. Which usually crashes the system or
otherwise silently corrupts the memory...
Note that there is a similar situation which can also happen during
`probe()`; the possibility of an interrupt firing _before_ registering
the `power_supply` handle. This would then lead to the nasty situation
of using the `power_supply` handle *uninitialized* in
`power_supply_changed()`.
Fix this racy use-after-free by making sure the IRQ is requested _after_
the registration of the `power_supply` handle.
Fixes: f8d7a3d211 ("power: supply: Add driver for pm8916 lbc")
Signed-off-by: Waqar Hameed <waqar.hameed@axis.com>
Reviewed-by: Nikita Travkin <nikita@trvn.ru>
Link: https://patch.msgid.link/64d8dd3675a4e59fa32c3e0ef451f12d1f7ed18f.1766268280.git.waqar.hameed@axis.com
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 62914959b3 ]
Using the `devm_` variant for requesting IRQ _before_ the `devm_`
variant for allocating/registering the `power_supply` handle, means that
the `power_supply` handle will be deallocated/unregistered _before_ the
interrupt handler (since `devm_` naturally deallocates in reverse
allocation order). This means that during removal, there is a race
condition where an interrupt can fire just _after_ the `power_supply`
handle has been freed, *but* just _before_ the corresponding
unregistration of the IRQ handler has run.
This will lead to the IRQ handler calling `power_supply_changed()` with
a freed `power_supply` handle. Which usually crashes the system or
otherwise silently corrupts the memory...
Note that there is a similar situation which can also happen during
`probe()`; the possibility of an interrupt firing _before_ registering
the `power_supply` handle. This would then lead to the nasty situation
of using the `power_supply` handle *uninitialized* in
`power_supply_changed()`.
Fix this racy use-after-free by making sure the IRQ is requested _after_
the registration of the `power_supply` handle.
Fixes: 098bce1838 ("power: supply: Add pm8916 VM-BMS support")
Signed-off-by: Waqar Hameed <waqar.hameed@axis.com>
Reviewed-by: Nikita Travkin <nikita@trvn.ru>
Link: https://patch.msgid.link/2749c09ff81fcac87ae48147e216135450d8c067.1766268280.git.waqar.hameed@axis.com
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b2ce982e2e ]
Using the `devm_` variant for requesting IRQ _before_ the `devm_`
variant for allocating/registering the `power_supply` handle, means that
the `power_supply` handle will be deallocated/unregistered _before_ the
interrupt handler (since `devm_` naturally deallocates in reverse
allocation order). This means that during removal, there is a race
condition where an interrupt can fire just _after_ the `power_supply`
handle has been freed, *but* just _before_ the corresponding
unregistration of the IRQ handler has run.
This will lead to the IRQ handler calling `power_supply_changed()` with
a freed `power_supply` handle. Which usually crashes the system or
otherwise silently corrupts the memory...
Note that there is a similar situation which can also happen during
`probe()`; the possibility of an interrupt firing _before_ registering
the `power_supply` handle. This would then lead to the nasty situation
of using the `power_supply` handle *uninitialized* in
`power_supply_changed()`.
Fix this racy use-after-free by making sure the IRQ is requested _after_
the registration of the `power_supply` handle.
Fixes: 84d7b76874 ("power: Add battery driver for goldfish emulator")
Signed-off-by: Waqar Hameed <waqar.hameed@axis.com>
Link: https://patch.msgid.link/500a606bb6fb6f2bb8d797e19a00cea9dd7b03c1.1766268280.git.waqar.hameed@axis.com
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 642f33e34b ]
Using the `devm_` variant for requesting IRQ _before_ the `devm_`
variant for allocating/registering the `power_supply` handle, means that
the `power_supply` handle will be deallocated/unregistered _before_ the
interrupt handler (since `devm_` naturally deallocates in reverse
allocation order). This means that during removal, there is a race
condition where an interrupt can fire just _after_ the `power_supply`
handle has been freed, *but* just _before_ the corresponding
unregistration of the IRQ handler has run.
This will lead to the IRQ handler calling `power_supply_changed()` with
a freed `power_supply` handle. Which usually crashes the system or
otherwise silently corrupts the memory...
Note that there is a similar situation which can also happen during
`probe()`; the possibility of an interrupt firing _before_ registering
the `power_supply` handle. This would then lead to the nasty situation
of using the `power_supply` handle *uninitialized* in
`power_supply_changed()`.
Fix this racy use-after-free by making sure the IRQ is requested _after_
the registration of the `power_supply` handle.
Fixes: 874b2adbed ("power: supply: cpcap-battery: Add a battery driver")
Signed-off-by: Waqar Hameed <waqar.hameed@axis.com>
Link: https://patch.msgid.link/81db58d610c9a51a68184f856cd431a934cccee2.1766268280.git.waqar.hameed@axis.com
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5f0b1cb419 ]
Using the `devm_` variant for requesting IRQ _before_ the `devm_`
variant for allocating/registering the `power_supply` handle, means that
the `power_supply` handle will be deallocated/unregistered _before_ the
interrupt handler (since `devm_` naturally deallocates in reverse
allocation order). This means that during removal, there is a race
condition where an interrupt can fire just _after_ the `power_supply`
handle has been freed, *but* just _before_ the corresponding
unregistration of the IRQ handler has run.
This will lead to the IRQ handler calling `power_supply_changed()` with
a freed `power_supply` handle. Which usually crashes the system or
otherwise silently corrupts the memory...
Note that there is a similar situation which can also happen during
`probe()`; the possibility of an interrupt firing _before_ registering
the `power_supply` handle. This would then lead to the nasty situation
of using the `power_supply` handle *uninitialized* in
`power_supply_changed()`.
Fix this racy use-after-free by making sure the IRQ is requested _after_
the registration of the `power_supply` handle.
Fixes: 5069185fc1 ("power: supply: bq25980: Add support for the BQ259xx family")
Signed-off-by: Waqar Hameed <waqar.hameed@axis.com>
Link: https://patch.msgid.link/8763035cadb959e14787b3837f2d3db61f6e1c34.1766268280.git.waqar.hameed@axis.com
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8005843369 ]
Using the `devm_` variant for requesting IRQ _before_ the `devm_`
variant for allocating/registering the `power_supply` handle, means that
the `power_supply` handle will be deallocated/unregistered _before_ the
interrupt handler (since `devm_` naturally deallocates in reverse
allocation order). This means that during removal, there is a race
condition where an interrupt can fire just _after_ the `power_supply`
handle has been freed, *but* just _before_ the corresponding
unregistration of the IRQ handler has run.
This will lead to the IRQ handler calling `power_supply_changed()` with
a freed `power_supply` handle. Which usually crashes the system or
otherwise silently corrupts the memory...
Note that there is a similar situation which can also happen during
`probe()`; the possibility of an interrupt firing _before_ registering
the `power_supply` handle. This would then lead to the nasty situation
of using the `power_supply` handle *uninitialized* in
`power_supply_changed()`.
Fix this racy use-after-free by making sure the IRQ is requested _after_
the registration of the `power_supply` handle.
Fixes: 32e4978bb9 ("power: supply: bq256xx: Introduce the BQ256XX charger driver")
Signed-off-by: Waqar Hameed <waqar.hameed@axis.com>
Link: https://patch.msgid.link/39da6da8cc060fa0382ca859f65071e791cb6119.1766268280.git.waqar.hameed@axis.com
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3291c51d46 ]
Using the `devm_` variant for requesting IRQ _before_ the `devm_`
variant for allocating/registering the `power_supply` handle, means that
the `power_supply` handle will be deallocated/unregistered _before_ the
interrupt handler (since `devm_` naturally deallocates in reverse
allocation order). This means that during removal, there is a race
condition where an interrupt can fire just _after_ the `power_supply`
handle has been freed, *but* just _before_ the corresponding
unregistration of the IRQ handler has run.
This will lead to the IRQ handler calling `power_supply_changed()` with
a freed `power_supply` handle. Which usually crashes the system or
otherwise silently corrupts the memory...
Note that there is a similar situation which can also happen during
`probe()`; the possibility of an interrupt firing _before_ registering
the `power_supply` handle. This would then lead to the nasty situation
of using the `power_supply` handle *uninitialized* in
`power_supply_changed()`.
Fix this racy use-after-free by making sure the IRQ is requested _after_
the registration of the `power_supply` handle.
Fixes: a09209acd6 ("power: supply: act8945a_charger: Add status change update support")
Signed-off-by: Waqar Hameed <waqar.hameed@axis.com>
Link: https://patch.msgid.link/bcf3a23b5187df0bba54a8c8fe09f8b8a0031dee.1766268280.git.waqar.hameed@axis.com
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c4af8a98bb ]
Using the `devm_` variant for requesting IRQ _before_ the `devm_`
variant for allocating/registering the `power_supply` handle, means that
the `power_supply` handle will be deallocated/unregistered _before_ the
interrupt handler (since `devm_` naturally deallocates in reverse
allocation order). This means that during removal, there is a race
condition where an interrupt can fire just _after_ the `power_supply`
handle has been freed, *but* just _before_ the corresponding
unregistration of the IRQ handler has run.
This will lead to the IRQ handler calling `power_supply_changed()` with
a freed `power_supply` handle. Which usually crashes the system or
otherwise silently corrupts the memory...
Note that there is a similar situation which can also happen during
`probe()`; the possibility of an interrupt firing _before_ registering
the `power_supply` handle. This would then lead to the nasty situation
of using the `power_supply` handle *uninitialized* in
`power_supply_changed()`.
Commit 1c1f13a006 ("power: supply: ab8500: Move to componentized
binding") introduced this issue during a refactorization. Fix this racy
use-after-free by making sure the IRQ is requested _after_ the
registration of the `power_supply` handle.
Fixes: 1c1f13a006 ("power: supply: ab8500: Move to componentized binding")
Signed-off-by: Waqar Hameed <waqar.hameed@axis.com>
Reviewed-by: Linus Walleij <linusw@kernel.org>
Link: https://patch.msgid.link/ccf83a09942cb8dda3dff70b2682f2c2e9cb97f2.1766268280.git.waqar.hameed@axis.com
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0789f92990 ]
During a reset, software-generated WCs cannot be reported via
interrupts. This may cause the ULP to miss some WCs.
To avoid this, add check in the CQ arm process: if a hardware reset
has occurred and there are still unreported soft-WCs, notify the ULP
to handle the remaining WCs, thereby preventing any loss of completions.
Fixes: 626903e935 ("RDMA/hns: Add support for reporting wc as software mode")
Signed-off-by: Chengchang Tang <tangchengchang@huawei.com>
Signed-off-by: Junxian Huang <huangjunxian6@hisilicon.com>
Link: https://patch.msgid.link/20260104064057.1582216-5-huangjunxian6@hisilicon.com
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 84bd5d60f0 ]
DSCP is not supported in RoCEv1, but get_dscp() is still called. If
get_dscp() returns an error, it'll eventually cause create_ah to fail
even when using RoCEv1.
Correct the return value and avoid calling get_dscp() when using
RoCEv1.
Fixes: ee20cc17e9 ("RDMA/hns: Support DSCP")
Signed-off-by: Junxian Huang <huangjunxian6@hisilicon.com>
Link: https://patch.msgid.link/20260104064057.1582216-4-huangjunxian6@hisilicon.com
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ddd6c8c873 ]
Some HCAs (e.g: ConnectX4) do not trigger a IB_EVENT_GID_CHANGE on
subnet prefix update from SM (PortInfo).
Since the commit d58c23c925 ("IB/core: Only update PKEY and GID caches
on respective events"), the GID cache is updated exclusively on
IB_EVENT_GID_CHANGE. If this event is not emitted, the subnet prefix in the
IPoIB interface’s hardware address remains set to its default value
(0xfe80000000000000).
Then rdma_bind_addr() failed because it relies on hardware address to
find the port GID (subnet_prefix + port GUID).
This patch fixes this issue by updating the GID cache on
IB_EVENT_CLIENT_REREGISTER event (emitted on PortInfo::ClientReregister=1).
Fixes: d58c23c925 ("IB/core: Only update PKEY and GID caches on respective events")
Signed-off-by: Etienne AUJAMES <eaujames@ddn.com>
Link: https://patch.msgid.link/aVUfsO58QIDn5bGX@eaujamesFR0130
Reviewed-by: Parav Pandit <parav@nvidia.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a3572bdc3a ]
As rkey had been initialized to zero, the WARN_ON_ONCE should never been
triggered. Remove it.
Fixes: 9cb8374804 ("RDMA/rtrs: server: main functionality")
Signed-off-by: Honggang LI <honggangli@163.com>
Link: https://patch.msgid.link/20251224023819.138846-1-honggangli@163.com
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit cdb1634de3 ]
Running ethtool repeatedly with a transceiver unknown to the driver or
firmware will cause the driver to spam the kernel logs with "unknown
xcvr type" messages which can distract from real issues; and this isn't
interesting information outside of debugging. Fix this by rate limiting
the output so that there are still notifications but not so many that
they flood the log.
Using dev_dbg_once() would reduce the number of messages further, but
this would miss the case where a different unknown transceiver type is
plugged in, and its status is requested.
Fixes: 4d03e00a21 ("ionic: Add initial ethtool support")
Signed-off-by: Eric Joyner <eric.joyner@amd.com>
Reviewed-by: Brett Creeley <brett.creeley@amd.com>
Link: https://patch.msgid.link/20260206224651.1491-1-eric.joyner@amd.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 484e834d53 ]
Make sure the OUT DBELL base address reflects the
latest values written to it.
Fix:
Add a wait until the OUT DBELL base address register
is updated with the DMA ring descriptor address,
and modify the setup_oq function to properly
handle failures.
Fixes: 2c0c32c72b ("octeon_ep_vf: add hardware configuration APIs")
Signed-off-by: Sathesh Edara <sedara@marvell.com>
Signed-off-by: Shinas Rasheed <srasheed@marvell.com>
Signed-off-by: Vimlesh Kumar <vimleshk@marvell.com>
Link: https://patch.msgid.link/20260206111510.1045092-4-vimleshk@marvell.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ce8fe3fc4f ]
Make sure the OUT DBELL base address reflects the
latest values written to it.
Fix:
Add a wait until the OUT DBELL base address register
is updated with the DMA ring descriptor address,
and modify the setup_oq function to properly
handle failures.
Fixes: 0807dc76f3 ("octeon_ep: support Octeon CN10K devices")
Signed-off-by: Sathesh Edara <sedara@marvell.com>
Signed-off-by: Shinas Rasheed <srasheed@marvell.com>
Signed-off-by: Vimlesh Kumar <vimleshk@marvell.com>
Link: https://patch.msgid.link/20260206111510.1045092-3-vimleshk@marvell.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 308e7e4d0a ]
There is a use-after-free bug in caif_serial where handle_tx() may
access ser->tty after the tty has been freed.
The race condition occurs between ldisc_close() and packet transmission:
CPU 0 (close) CPU 1 (xmit)
------------- ------------
ldisc_close()
tty_kref_put(ser->tty)
[tty may be freed here]
<-- race window -->
caif_xmit()
handle_tx()
tty = ser->tty // dangling ptr
tty->ops->write() // UAF!
schedule_work()
ser_release()
unregister_netdevice()
The root cause is that tty_kref_put() is called in ldisc_close() while
the network device is still active and can receive packets.
Since ser and tty have a 1:1 binding relationship with consistent
lifecycles (ser is allocated in ldisc_open and freed in ser_release
via unregister_netdevice, and each ser binds exactly one tty), we can
safely defer the tty reference release to ser_release() where the
network device is unregistered.
Fix this by moving tty_kref_put() from ldisc_close() to ser_release(),
after unregister_netdevice(). This ensures the tty reference is held
as long as the network device exists, preventing the UAF.
Note: We save ser->tty before unregister_netdevice() because ser is
embedded in netdev's private data and will be freed along with netdev
(needs_free_netdev = true).
How to reproduce: Add mdelay(500) at the beginning of ldisc_close()
to widen the race window, then run the reproducer program [1].
Note: There is a separate deadloop issue in handle_tx() when using
PORT_UNKNOWN serial ports (e.g., /dev/ttyS3 in QEMU without proper
serial backend). This deadloop exists even without this patch,
and is likely caused by inconsistency between uart_write_room() and
uart_write() in serial core. It has been addressed in a separate
patch [2].
KASAN report:
==================================================================
BUG: KASAN: slab-use-after-free in handle_tx+0x5d1/0x620
Read of size 1 at addr ffff8881131e1490 by task caif_uaf_trigge/9929
Call Trace:
<TASK>
dump_stack_lvl+0x10e/0x1f0
print_report+0xd0/0x630
kasan_report+0xe4/0x120
handle_tx+0x5d1/0x620
dev_hard_start_xmit+0x9d/0x6c0
__dev_queue_xmit+0x6e2/0x4410
packet_xmit+0x243/0x360
packet_sendmsg+0x26cf/0x5500
__sys_sendto+0x4a3/0x520
__x64_sys_sendto+0xe0/0x1c0
do_syscall_64+0xc9/0xf80
entry_SYSCALL_64_after_hwframe+0x77/0x7f
RIP: 0033:0x7f615df2c0d7
Allocated by task 9930:
Freed by task 64:
Last potentially related work creation:
The buggy address belongs to the object at ffff8881131e1000
which belongs to the cache kmalloc-cg-2k of size 2048
The buggy address is located 1168 bytes inside of
freed 2048-byte region [ffff8881131e1000, ffff8881131e1800)
The buggy address belongs to the physical page:
page_owner tracks the page as allocated
page last free pid 9778 tgid 9778 stack trace:
Memory state around the buggy address:
ffff8881131e1380: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
ffff8881131e1400: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
>ffff8881131e1480: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
^
ffff8881131e1500: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
ffff8881131e1580: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
==================================================================
[1]: https://gist.github.com/mrpre/f683f244544f7b11e7fa87df9e6c2eeb
[2]: https://lore.kernel.org/linux-serial/20260204074327.226165-1-jiayuan.chen@linux.dev/T/#u
Reported-by: syzbot+827272712bd6d12c79a4@syzkaller.appspotmail.com
Closes: https://lore.kernel.org/all/000000000000a4a7550611e234f5@google.com/T/
Fixes: 56e0ef527b ("drivers/net: caif: fix wrong rtnl_is_locked() usage")
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Jiayuan Chen <jiayuan.chen@shopee.com>
Reviewed-by: Jijie Shao <shaojijie@huawei.com>
Link: https://patch.msgid.link/20260206074450.154267-1-jiayuan.chen@linux.dev
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 81b84de32b ]
icmp_route_lookup() performs multiple route lookups to find a suitable
route for sending ICMP error messages, with special handling for XFRM
(IPsec) policies.
The lookup sequence is:
1. First, lookup output route for ICMP reply (dst = original src)
2. Pass through xfrm_lookup() for policy check
3. If blocked (-EPERM) or dst is not local, enter "reverse path"
4. In reverse path, call xfrm_decode_session_reverse() to get fl4_dec
which reverses the original packet's flow (saddr<->daddr swapped)
5. If fl4_dec.saddr is local (we are the original destination), use
__ip_route_output_key() for output route lookup
6. If fl4_dec.saddr is NOT local (we are a forwarding node), use
ip_route_input() to simulate the reverse packet's input path
7. Finally, pass rt2 through xfrm_lookup() with XFRM_LOOKUP_ICMP flag
The bug occurs in step 6: ip_route_input() is called with fl4_dec.daddr
(original packet's source) as destination. If this address becomes local
between the initial check and ip_route_input() call (e.g., due to
concurrent "ip addr add"), ip_route_input() returns a LOCAL route with
dst.output set to ip_rt_bug.
This route is then used for ICMP output, causing dst_output() to call
ip_rt_bug(), triggering a WARN_ON:
------------[ cut here ]------------
WARNING: net/ipv4/route.c:1275 at ip_rt_bug+0x21/0x30, CPU#1
Call Trace:
<TASK>
ip_push_pending_frames+0x202/0x240
icmp_push_reply+0x30d/0x430
__icmp_send+0x1149/0x24f0
ip_options_compile+0xa2/0xd0
ip_rcv_finish_core+0x829/0x1950
ip_rcv+0x2d7/0x420
__netif_receive_skb_one_core+0x185/0x1f0
netif_receive_skb+0x90/0x450
tun_get_user+0x3413/0x3fb0
tun_chr_write_iter+0xe4/0x220
...
Fix this by checking rt2->rt_type after ip_route_input(). If it's
RTN_LOCAL, the route cannot be used for output, so treat it as an error.
The reproducer requires kernel modification to widen the race window,
making it unsuitable as a selftest. It is available at:
https://gist.github.com/mrpre/eae853b72ac6a750f5d45d64ddac1e81
Reported-by: syzbot+e738404dcd14b620923c@syzkaller.appspotmail.com
Closes: https://lore.kernel.org/all/000000000000b1060905eada8881@google.com/T/
Closes: https://lore.kernel.org/r/20260128090523.356953-1-jiayuan.chen@linux.dev
Fixes: 8b7817f3a9 ("[IPSEC]: Add ICMP host relookup support")
Signed-off-by: Jiayuan Chen <jiayuan.chen@shopee.com>
Signed-off-by: Jiayuan Chen <jiayuan.chen@linux.dev>
Link: https://patch.msgid.link/20260206050220.59642-1-jiayuan.chen@linux.dev
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e97e6a1830 ]
Going forward skb_dst_set will assert that skb dst_entry
is empty during skb_dst_set. skb_dstref_steal is added to reset
existing entry without doing refcnt. skb_dstref_restore should
be used to restore the previous entry. Convert icmp_route_lookup
and ip_options_rcv_srr to these helpers. Add extra call to
skb_dstref_reset to icmp_route_lookup to clear the ip_route_input
entry.
Signed-off-by: Stanislav Fomichev <sdf@fomichev.me>
Link: https://patch.msgid.link/20250818154032.3173645-5-sdf@fomichev.me
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Stable-dep-of: 81b84de32b ("xfrm: fix ip_rt_bug race in icmp_route_lookup reverse path")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c3f0c02997 ]
Going forward skb_dst_set will assert that skb dst_entry
is empty during skb_dst_set to prevent potential leaks. There
are few places that still manually manage dst_entry not using
the helpers. Convert them to the following new helpers:
- skb_dstref_steal that resets dst_entry and returns previous dst_entry
value
- skb_dstref_restore that restores dst_entry previously reset via
skb_dstref_steal
Signed-off-by: Stanislav Fomichev <sdf@fomichev.me>
Link: https://patch.msgid.link/20250818154032.3173645-2-sdf@fomichev.me
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Stable-dep-of: 81b84de32b ("xfrm: fix ip_rt_bug race in icmp_route_lookup reverse path")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ae88a5d2f2 ]
Reproducer available at [1].
The ATM send path (sendmsg -> vcc_sendmsg -> sigd_send) reads the vcc
pointer from msg->vcc and uses it directly without any validation. This
pointer comes from userspace via sendmsg() and can be arbitrarily forged:
int fd = socket(AF_ATMSVC, SOCK_DGRAM, 0);
ioctl(fd, ATMSIGD_CTRL); // become ATM signaling daemon
struct msghdr msg = { .msg_iov = &iov, ... };
*(unsigned long *)(buf + 4) = 0xdeadbeef; // fake vcc pointer
sendmsg(fd, &msg, 0); // kernel dereferences 0xdeadbeef
In normal operation, the kernel sends the vcc pointer to the signaling
daemon via sigd_enq() when processing operations like connect(), bind(),
or listen(). The daemon is expected to return the same pointer when
responding. However, a malicious daemon can send arbitrary pointer values.
Fix this by introducing find_get_vcc() which validates the pointer by
searching through vcc_hash (similar to how sigd_close() iterates over
all VCCs), and acquires a reference via sock_hold() if found.
Since struct atm_vcc embeds struct sock as its first member, they share
the same lifetime. Therefore using sock_hold/sock_put is sufficient to
keep the vcc alive while it is being used.
Note that there may be a race with sigd_close() which could mark the vcc
with various flags (e.g., ATM_VF_RELEASED) after find_get_vcc() returns.
However, sock_hold() guarantees the memory remains valid, so this race
only affects the logical state, not memory safety.
[1]: https://gist.github.com/mrpre/1ba5949c45529c511152e2f4c755b0f3
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Reported-by: syzbot+1f22cb1769f249df9fa0@syzkaller.appspotmail.com
Closes: https://lore.kernel.org/all/69039850.a70a0220.5b2ed.005d.GAE@google.com/T/
Signed-off-by: Jiayuan Chen <jiayuan.chen@shopee.com>
Link: https://patch.msgid.link/20260205095501.131890-1-jiayuan.chen@linux.dev
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4a93d1ee2d ]
When we download a file without rdma offload or get
a large directly enumeration from the server,
the server might want to send up to smbd_max_fragmented_recv_size
bytes, but if it is too large all our recv buffers
might already be moved to the recv_io.reassembly.list
and we're no longer able to grant recv credits.
The maximum fragmented upper-layer payload receive size supported
Assume max_payload_per_credit is
smbd_max_receive_size - 24 = 1340
The maximum number would be
smbd_receive_credit_max * max_payload_per_credit
1340 * 255 = 341700 (0x536C4)
The minimum value from the spec is 131072 (0x20000)
For now we use the logic we used in ksmbd before:
(1364 * 255) / 2 = 173910 (0x2A756)
Fixes: 03bee01d62 ("CIFS: SMBD: Add SMB Direct protocol initial values and constants")
Cc: Steve French <smfrench@gmail.com>
Cc: Tom Talpey <tom@talpey.com>
Cc: Long Li <longli@microsoft.com>
Cc: Namjae Jeon <linkinjeon@kernel.org>
Cc: linux-cifs@vger.kernel.org
Cc: samba-technical@lists.samba.org
Signed-off-by: Stefan Metzmacher <metze@samba.org>
Signed-off-by: Steve French <stfrench@microsoft.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6d2f142b1e ]
In hns3_set_ringparam(), a temporary copy (tmp_rings) of the ring structure
is created for rollback. However, the tx_spare pointer in the original
ring handle is incorrectly left pointing to the old backup memory.
Later, if memory allocation fails in hns3_init_all_ring() during the setup,
the error path attempts to free all newly allocated rings. Since tx_spare
contains a stale (non-NULL) pointer from the backup, it is mistaken for
a newly allocated buffer and is erroneously freed, leading to a double-free
of the backup memory.
The root cause is that the tx_spare field was not cleared after its value
was saved in tmp_rings, leaving a dangling pointer.
Fix this by setting tx_spare to NULL in the original ring structure
when the creation of the new `tx_spare` fails. This ensures the
error cleanup path only frees genuinely newly allocated buffers.
Fixes: 907676b130 ("net: hns3: use tx bounce buffer for small packets")
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Jijie Shao <shaojijie@huawei.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Link: https://patch.msgid.link/20260205121719.3285730-1-shaojijie@huawei.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5907a90551 ]
12d8:b404 is apparently another PCI ID for Pericom PI7C9X2G404 (as
identified by the chip silkscreen and lspci).
It is also affected by the PI7C9X2G errata (e.g. a network card attached
to it fails under load when P2P Redirect Request is enabled), so apply
the same quirk to this PCI ID too.
PCI bridge [0604]: Pericom Semiconductor PI7C9X2G404 EV/SV PCIe2 4-Port/4-Lane Packet Switch [12d8:b404] (rev 01)
Fixes: acd61ffb2f ("PCI: Add ACS quirk for Pericom PI7C9X2G switches")
Closes: https://lore.kernel.org/all/a1d926f0-4cb5-4877-a4df-617902648d80@green-communications.fr/
Signed-off-by: Nicolas Cavallari <nicolas.cavallari@green-communications.fr>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Link: https://patch.msgid.link/20260119160915.26456-1-nicolas.cavallari@green-communications.fr
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4780ec142c ]
Userspace provides an optimized representation in case intervals are
adjacent, where the end element is omitted.
The existing partial overlap detection logic skips anonymous set checks
on start elements for this reason.
However, it is possible to add intervals that overlap to this anonymous
where two start elements with the same, eg. A-B, A-C where C < B.
start end
A B
start end
A C
Restore the check on overlapping start elements to report an overlap.
Fixes: c9e6978e27 ("netfilter: nft_set_rbtree: Switch to node list walk for overlap detection")
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7f9203f41a ]
Userspace adds a non-matching null element to the kernel for historical
reasons. This null element is added when the set is populated with
elements. Inclusion of this element is conditional, therefore,
userspace needs to dump the set content to check for its presence.
If the NLM_F_CREATE flag is turned on, this becomes an issue because
kernel bogusly reports EEXIST.
Add special case to ignore NLM_F_CREATE in this case, therefore,
re-adding the nul-element never fails.
Fixes: c016c7e45d ("netfilter: nf_tables: honor NLM_F_EXCL flag in set element insertion")
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1e13f27e06 ]
nft_counter_reset() calls u64_stats_add() with a negative value to reset
the counter. This will work on 64bit archs, hence the negative value
added will wrap as a 64bit value which then can wrap the stat counter as
well.
On 32bit archs, the added negative value will wrap as a 32bit value and
_not_ wrapping the stat counter properly. In most cases, this would just
lead to a very large 32bit value being added to the stat counter.
Fix by introducing u64_stats_sub().
Fixes: 4a1d3acd6e ("netfilter: nft_counter: Use u64_stats_t for statistic.")
Signed-off-by: Anders Grahn <anders.grahn@gmail.com>
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2f635adbe2 ]
tests/shell/testcases/packetpath/set_match_nomatch_hash_fast
fails on big endian with:
Error: Could not process rule: No such file or directory
reset element ip test s { 244.147.90.126 }
^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^
Fatal: Cannot fetch element "244.147.90.126"
... because the wrong bucket is searched, jhash() and jhash1_word are
not interchangeable on big endian.
Fixes: 3b02b0adc2 ("netfilter: nft_set_hash: fix lookups with fixed size hash on big endian")
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 207b3ebacb ]
Ulrich reports a regression with nfqueue:
If an application did not set the 'F_GSO' capability flag and a gso
packet with an unconfirmed nf_conn entry is received all packets are
now dropped instead of queued, because the check happens after
skb_gso_segment(). In that case, we did have exclusive ownership
of the skb and its associated conntrack entry. The elevated use
count is due to skb_clone happening via skb_gso_segment().
Move the check so that its peformed vs. the aggregated packet.
Then, annotate the individual segments except the first one so we
can do a 2nd check at reinject time.
For the normal case, where userspace does in-order reinjects, this avoids
packet drops: first reinjected segment continues traversal and confirms
entry, remaining segments observe the confirmed entry.
While at it, simplify nf_ct_drop_unconfirmed(): We only care about
unconfirmed entries with a refcnt > 1, there is no need to special-case
dying entries.
This only happens with UDP. With TCP, the only unconfirmed packet will
be the TCP SYN, those aren't aggregated by GRO.
Next patch adds a udpgro test case to cover this scenario.
Reported-by: Ulrich Weber <ulrich.weber@gmail.com>
Fixes: 7d8dc1c7be ("netfilter: nf_queue: drop packets with cloned unconfirmed conntracks")
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e19079adcd ]
The current implementation uses a linear list to find queued packets by
ID when processing verdicts from userspace. With large queue depths and
out-of-order verdicting, this O(n) lookup becomes a significant
bottleneck, causing userspace verdict processing to dominate CPU time.
Replace the linear search with a hash table for O(1) average-case
packet lookup by ID. A global rhashtable spanning all network
namespaces attributes hash bucket memory to kernel but is subject to
fixed upper bound.
Signed-off-by: Scott Mitchell <scott.k.mitch1@gmail.com>
Signed-off-by: Florian Westphal <fw@strlen.de>
Stable-dep-of: 207b3ebacb ("netfilter: nfnetlink_queue: do shared-unconfirmed check before segmentation")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c9efde1e53 ]
llc_shdlc_deinit() purges SHDLC skb queues and frees the llc_shdlc
structure while its timers and state machine work may still be active.
Timer callbacks can schedule sm_work, and sm_work accesses SHDLC state
and the skb queues. If teardown happens in parallel with a queued/running
work item, it can lead to UAF and other shutdown races.
Stop all SHDLC timers and cancel sm_work synchronously before purging the
queues and freeing the context.
Found by Linux Verification Center (linuxtesting.org) with SVACE.
Fixes: 4a61cd6687 ("NFC: Add an shdlc llc module to llc core")
Signed-off-by: Votokina Victoria <Victoria.Votokina@kaspersky.com>
Link: https://patch.msgid.link/20260203113158.2008723-1-Victoria.Votokina@kaspersky.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c89477ad79 ]
Yizhou Zhao reported that simply having one RAW socket on protocol
IPPROTO_RAW (255) was dangerous.
socket(AF_INET, SOCK_RAW, 255);
A malicious incoming ICMP packet can set the protocol field to 255
and match this socket, leading to FNHE cache changes.
inner = IP(src="192.168.2.1", dst="8.8.8.8", proto=255)/Raw("TEST")
pkt = IP(src="192.168.1.1", dst="192.168.2.1")/ICMP(type=3, code=4, nexthopmtu=576)/inner
"man 7 raw" states:
A protocol of IPPROTO_RAW implies enabled IP_HDRINCL and is able
to send any IP protocol that is specified in the passed header.
Receiving of all IP protocols via IPPROTO_RAW is not possible
using raw sockets.
Make sure we drop these malicious packets.
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Reported-by: Yizhou Zhao <zhaoyz24@mails.tsinghua.edu.cn>
Link: https://lore.kernel.org/netdev/20251109134600.292125-1-zhaoyz24@mails.tsinghua.edu.cn/
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: David Ahern <dsahern@kernel.org>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Link: https://patch.msgid.link/20260203192509.682208-1-edumazet@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 48dec8d88a ]
bond_update_speed_duplex() first set speed/duplex to unknown and
then asks slave driver for current speed/duplex. Since getting
speed/duplex might take longer there is a race, where this false state
is visible by /proc/net/bonding. With commit 691b2bf149 ("bonding:
update port speed when getting bond speed") this race gets more visible,
if user space is calling ethtool on a regular base.
Fix this by only setting speed/duplex to unknown, if link speed is
really unknown/unusable.
Fixes: 98f41f694f ("bonding:update speed/duplex for NETDEV_CHANGE")
Signed-off-by: Thomas Bogendoerfer <tbogendoerfer@suse.de>
Acked-by: Jay Vosburgh <jv@jvosburgh.net>
Reviewed-by: Nikolay Aleksandrov <razor@blackwall.org>
Reviewed-by: Hangbin Liu <liuhangbin@gmail.com>
Link: https://patch.msgid.link/20260203141153.51581-1-tbogendoerfer@suse.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2d2d574309 ]
During a kexec reboot the hardware is not power-cycled, so AF state from
the old kernel can persist into the new kernel. When AF and PF drivers
are built as modules, the PF driver may probe before AF reinitializes
the hardware.
The PF driver treats the RVUM block revision as an indication that AF
initialization is complete. If this value is left uncleared at shutdown,
PF may incorrectly assume AF is ready and access stale hardware state,
leading to a crash.
Clear the RVUM block revision during AF shutdown to avoid PF
mis-detecting AF readiness after kexec.
Fixes: 54494aa5d1 ("octeontx2-af: Add Marvell OcteonTX2 RVU AF driver")
Signed-off-by: Anshumali Gaur <agaur@marvell.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Link: https://patch.msgid.link/20260203050701.2616685-1-agaur@marvell.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 70274765fe ]
MPTCP initialize the receive buffer stamp in mptcp_rcv_space_init(),
using the provided subflow stamp. Such helper is invoked in several
places; for passive sockets, space init happened at clone time.
In such scenario, MPTCP ends-up accesses the subflow stamp before
its initialization, leading to quite randomic timing for the first
receive buffer auto-tune event, as the timestamp for newly created
subflow is not refreshed there.
Fix the issue moving the stamp initialization out of the mentioned helper,
at the data transfer start, and always using a fresh timestamp.
Fixes: 013e3179db ("mptcp: fix rcv space initialization")
Reviewed-by: Mat Martineau <martineau@kernel.org>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Matthieu Baerts (NGI0) <matttbe@kernel.org>
Link: https://patch.msgid.link/20260203-net-next-mptcp-misc-feat-6-20-v1-2-31ec8bfc56d1@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d289cb7fce ]
This function first duplicates p1 and p2 into new, and then checks whether
the duplication succeeds. However, if the duplication fails (e.g.,
kzalloc() returns NULL in __of_prop_dup()), new will be NULL but is still
dereferenced in __of_prop_free(). To ensure that the unit test continues to
run even when duplication fails, add a NULL check before calling
__of_prop_free().
Fixes: 1c5e3d9bf3 ("of: Add a helper to free property struct")
Signed-off-by: Tuo Li <islituo@gmail.com>
Link: https://patch.msgid.link/20260105071438.156186-1-islituo@gmail.com
Signed-off-by: Rob Herring (Arm) <robh@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0895a000e4 ]
The user.* sysctls implement the ctl_table_root::permissions hook and they
override the file access mode based on the CAP_SYS_RESOURCE capability (at
most rwx if capable, at most r-- if not). The capability is being checked
unconditionally, so if an LSM denies the capability, an audit record may
be logged even when access is in fact granted.
Given the logic in the set_permissions() function in kernel/ucount.c and
the unfortunate way the permission checking is implemented, it doesn't
seem viable to avoid false positive denials by deferring the capability
check. Thus, do the same as in net_ctl_permissions() (net/sysctl_net.c) -
switch from ns_capable() to ns_capable_noaudit(), so that the check never
logs an audit record.
Link: https://lkml.kernel.org/r/20260122140745.239428-1-omosnace@redhat.com
Fixes: dbec28460a ("userns: Add per user namespace sysctls.")
Signed-off-by: Ondrej Mosnacek <omosnace@redhat.com>
Reviewed-by: Paul Moore <paul@paul-moore.com>
Acked-by: Serge Hallyn <serge@hallyn.com>
Cc: Eric Biederman <ebiederm@xmission.com>
Cc: Alexey Gladkov <legion@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
