Track the minimum link BPP as an x16 fixed-point value and, for
clarity, rename the variable storing it to min_link_bpp_x16.
Reviewed-by: Ankit Nautiyal <ankit.k.nautiyal@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patch.msgid.link/20260216070421.714884-4-imre.deak@intel.com
Export intel_dp_compute_min_compressed_bpp_x16() for use by a
follow-up change validating MST modes with DSC enabled.
Reviewed-by: Ankit Nautiyal <ankit.k.nautiyal@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patch.msgid.link/20260216070421.714884-3-imre.deak@intel.com
Add the missing check for a valid slice count during
mode validation when DSC is enabled.
Cc: Vinod Govindapillai <vinod.govindapillai@intel.com>
Fixes: 745395b51c ("drm/i915/dp: Add intel_dp_mode_valid_with_dsc()")
Reviewed-by: Ankit Nautiyal <ankit.k.nautiyal@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patch.msgid.link/20260216070421.714884-2-imre.deak@intel.com
The user's request for a maximum BPC - via the max-bpc connector
property - determines the pipe BPP selected by the encoder, which is in
turn used either as the uncompressed output BPP or as the input BPP for
the DSC engine. This user-requested BPC->BPP can be outside of the
source/sink's supported valid min/max pipe BPP range and atm such an
out-of-bound request will be rejected by the encoder's state
computation.
As opposed to the above, the semantics for the max-bpc connector
property - which the user may reasonably expect - should not be to
fail the modeset in case of an out-of-bound max BPC request, but rather
to adjust the request, clamping it to the valid BPP range.
Based on the above, calculate the baseline (i.e. the non-DP specific
platform/EDID) _maximum_ pipe BPP, storing it in
intel_crtc_state::max_pipe_bpp, separately from the baseline _target_
pipe BPP (which is the lower BPP of the baseline maximum and requested
maximum BPP, stored in intel_crtc_state::pipe_bpp). This allows the
encoder state computation to use the baseline maximum pipe BPP as a hard
limit for the selected pipe BPP, while also letting it use the baseline
target pipe BPP only as a preference, clamping this target BPP to the
valid DP pipe BPP range.
v2:
- Fix typos in the commit message. (Michał)
- Clarify code comment's reference to the baseline max BPP value.
(Ankit)
Reviewed-by: Michał Grzelak <michal.grzelak@intel.com>
Reviewed-by: Ankit Nautiyal <ankit.k.nautiyal@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patch.msgid.link/20260211115811.508496-2-imre.deak@intel.com
Clarify that the baseline pipe BPP - i.e. the non-DP specific
platform/EDID maximum BPP limited by any user-requested max-bpc setting
- set by compute_sink_pipe_bpp() is a baseline _target_ pipe BPP. This
target BPP can get either rejected or adjusted (lowering or increasing
it as needed) by the encoder state computation based on other
constraints, like a minimum pipe BPP dictated by a non-RGB output format
(24 BPP) or a min/max DSC input BPP dictated by a DSC sink. Whether an
out-of-bound target BPP is adjusted or rejected depends on the max-bpc
property's semantics assumed by the driver, which is atm to reject such a
request.
A follow-up change will also compute the baseline _maximum_ pipe BPP,
which is the non-DP specific platform/EDID maximum BPP w/o the requested
max-bpc adjustment and as such is a hard limit: the encoder state
computation must ensure that the final BPP selected for the modeset is
below this maximum. Tracking the baseline maximum pipe BPP separately
will allow for adjusting the baseline target BPP as needed, clamping it
to the valid DP min/max pipe BPP range, instead of rejecting an
out-of-bound BPC/BPP request.
To clarify the above semantics rename bpp in compute_sink_pipe_bpp() to
target_pipe_bpp in this patch, preparing for a follow-up change also
computing max_pipe_bpp in the same function.
v2: Fix typos in the commit log. (Michał)
Reviewed-by: Michał Grzelak <michal.grzelak@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patch.msgid.link/20260211115811.508496-1-imre.deak@intel.com
Move GEN9_CLKGATE_DIS_0 reg to display header to make
intel_modeset_setup.c free from i915_reg.h include.
v2: Remove from gmd common header and use display_regs.h (Jani)
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Uma Shankar <uma.shankar@intel.com>
Link: https://patch.msgid.link/20260205094341.1882816-20-uma.shankar@intel.com
Make intel_display_power_well.c free from including i915_reg.h.
v3: Separate bit field for VLV (Ville)
v2: Include specific pcode header, drop common header (Jani)
Signed-off-by: Uma Shankar <uma.shankar@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patch.msgid.link/20260205094341.1882816-19-uma.shankar@intel.com
Move VLV_IRQ_REGS to common header for interrupt to make
intel_display_irq.c free from including i915_reg.h.
v2: Move interrupt to dedicated header (Jani)
Signed-off-by: Uma Shankar <uma.shankar@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patch.msgid.link/20260205094341.1882816-18-uma.shankar@intel.com
Move GEN7_ERR_INT reg to common header to make intel_fifo_underrun.c
free from including i915_reg.h.
v2: Move GEN7_ERR_INT regs to display header (Jani)
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Uma Shankar <uma.shankar@intel.com>
Link: https://patch.msgid.link/20260205094341.1882816-17-uma.shankar@intel.com
Move some chicken registers to display header to make
intel_psr.c free from including i915_reg.h.
v3: Update commit header
v2: Use display header instead of gmd common include (Jani)
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Uma Shankar <uma.shankar@intel.com>
Link: https://patch.msgid.link/20260205094341.1882816-16-uma.shankar@intel.com
Make intel_rom.c free from including i915_reg.h.
v5: Use SPDX (Jani)
v4: Move oprom reg to separate header (Ville)
v3: Update patch header
v2: Use display header instead of gmd common include (Jani)
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Uma Shankar <uma.shankar@intel.com>
Link: https://patch.msgid.link/20260205094341.1882816-15-uma.shankar@intel.com
Move TRANS_CHICKEN1 reg to display header to make g4x_hdmi.c
free from i915_reg.h dependency.
v2: Remove from common header in include and use display_regs.h (Jani)
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Uma Shankar <uma.shankar@intel.com>
Link: https://patch.msgid.link/20260205094341.1882816-14-uma.shankar@intel.com
Move FW_BLC_SELF to common header to make i9xx_wm.c
free from i915_reg.h include. Introduce a common
intel_gmd_misc_regs.h to define common miscellaneous
register definitions across graphics and display.
v3: MISC header included as needed, drop from i915_reg (Jani)
v2: Introdue a common misc header for GMD
Signed-off-by: Uma Shankar <uma.shankar@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patch.msgid.link/20260205094341.1882816-13-uma.shankar@intel.com
Move DE_IRQ_REGS to display header to make g4x_dp.c
free from i915_reg.h dependency. These registers are
only used by display and gvt.
v3: Drop a superfluous include (Jani)
v2: Move DE interrupt regs from common to display header (Jani)
Signed-off-by: Uma Shankar <uma.shankar@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patch.msgid.link/20260205094341.1882816-12-uma.shankar@intel.com
Move GEN2_ISR and some interrupt definitions to common header.
This removes dependency of i915_reg.h from intel_overlay.c.
v3: Rename interrupt header with regs suffix (Jani)
v2: Create a separate file for common interrupts (Jani)
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Uma Shankar <uma.shankar@intel.com>
Link: https://patch.msgid.link/20260205094341.1882816-11-uma.shankar@intel.com
Move CHICKEN_PIPESL_1 register definition to display header.
This allows intel_display.c free of i915_reg.h include.
v3: Fix commit header (Jani)
v2: Drop common header in include and use display_regs.h (Jani)
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Uma Shankar <uma.shankar@intel.com>
Link: https://patch.msgid.link/20260205094341.1882816-10-uma.shankar@intel.com
Make intel_dram.c free from including i915_reg.h.
v3: Move MEM_SS info reg to display instead of pcode header (Jani)
v2: Move mem config register to newly added pcode header (Jani)
Signed-off-by: Uma Shankar <uma.shankar@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patch.msgid.link/20260205094341.1882816-9-uma.shankar@intel.com
Move GU_CNTL_PROTECTED and GMD_ID_DISPLAY to common header,
this helps intel_display_device.c free from i915_reg.h dependency.
v2: Move GMD_ID_DISPLAY to display header instead of common (Jani)
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Uma Shankar <uma.shankar@intel.com>
Link: https://patch.msgid.link/20260205094341.1882816-7-uma.shankar@intel.com
There are certain register definitions which are commonly shared
by i915, xe and display. Extract the same to a common header to
avoid duplication.
Move GEN6_PCODE_MAILBOX to common pcode header to make intel_cdclk.c
free from including i915_reg.h.
v3: Include pcode header as required, instead in i915_reg.h (Jani)
v2: Make the header granular and per feature (Jani)
Signed-off-by: Uma Shankar <uma.shankar@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patch.msgid.link/20260205094341.1882816-6-uma.shankar@intel.com
Move DSPCLK_GATE_D register definition to display header.
This allows intel_gmbus.c not to include i915_reg.h.
v3: Update commit header and message (Jani)
v2: Drop common header in include and use display_regs.h (Jani)
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Uma Shankar <uma.shankar@intel.com>
Link: https://patch.msgid.link/20260205094341.1882816-5-uma.shankar@intel.com
Extract DE Interrupt registers from i915_reg.h to display header.
This allows intel_display_rps.c not to include i915_reg.h
v2: Update commit message (Jani)
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Uma Shankar <uma.shankar@intel.com>
Link: https://patch.msgid.link/20260205094341.1882816-4-uma.shankar@intel.com
Extract South Chicken registers from i915_reg.h to display header.
This allows intel_pch_refclk.c not to include i915_reg.h
v3: Drop whitespace changes, commit header updated (Jani)
v2: Drop common header in include and use display_regs.h (Jani)
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Uma Shankar <uma.shankar@intel.com>
Link: https://patch.msgid.link/20260205094341.1882816-3-uma.shankar@intel.com
There are certain register definitions which are defined in i915_reg.h
which are exclusively needed by display. Move the same to display
headers to remove i915_reg.h includes from display. This is a step
towards making display independent of i915.
intel_clock_gating.c can include display header directly, since its
usage is planned to be re-factored and will be moved within display.
v3: Updated subject and commit message (Jani)
v2: Drop common header in include and use display_regs.h (Jani)
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Uma Shankar <uma.shankar@intel.com>
Link: https://patch.msgid.link/20260205094341.1882816-2-uma.shankar@intel.com
acpi_evaluate_dsm_typed() returns an ACPI package in pkg.
When pkg->package.count == 0, we returned without freeing pkg,
leaking memory. Free pkg before returning on the empty case.
Signed-off-by: Kaushlendra Kumar <kaushlendra.kumar@intel.com>
Fixes: 337d7a1621 ("drm/i915: Fix invalid access to ACPI _DSM objects")
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patch.msgid.link/20260109032549.1826303-1-kaushlendra.kumar@intel.com
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Commit c5741c5c11 ("drm/i915/display: Do not use stolen on MTL") added
some checks for MTL in overlay code. However, this is never run on
MTL. Clean it up.
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patch.msgid.link/20260206125949.243643-1-jani.nikula@intel.com
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Ensure that the pipe BPP range is valid after calculating the minimum
and maximum pipe BPP values separately.
Reviewed-by: Ankit Nautiyal <ankit.k.nautiyal@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patch.msgid.link/20260209133817.395823-2-imre.deak@intel.com
The pipe BPP value shouldn't be set outside of the source's / sink's
valid pipe BPP range, ensure this when increasing the minimum pipe BPP
value to 30 due to HDR.
While at it debug print if the HDR mode was requested for a connector by
setting the corresponding HDR connector property. This indicates
if the requested HDR mode could not be enabled, since the selected
pipe BPP is below 30, due to a sink capability or link BW limit.
v2:
- Also handle the case where the sink could support the target 30 BPP
only in DSC mode due to a BW limit, but the sink doesn't support DSC
or 30 BPP as a DSC input BPP. (Chaitanya)
- Debug print the connector's HDR mode in the link config dump, to
indicate if a BPP >= 30 required by HDR couldn't be reached. (Ankit)
- Add Closes: trailer. (Ankit)
- Don't print the 30 BPP-outside of valid BPP range debug message if
the min BPP is already > 30 (and so a target BPP >= 30 required
for HDR is ensured).
Closes: https://gitlab.freedesktop.org/drm/xe/kernel/-/issues/7052
Closes: https://gitlab.freedesktop.org/drm/i915/kernel/-/issues/15503
Fixes: ba49a4643c ("drm/i915/dp: Set min_bpp limit to 30 in HDR mode")
Cc: Chaitanya Kumar Borah <chaitanya.kumar.borah@intel.com>
Cc: <stable@vger.kernel.org> # v6.18+
Reviewed-by: Ankit Nautiyal <ankit.k.nautiyal@intel.com> # v1
Reviewed-by: Chaitanya Kumar Borah <chaitanya.kumar.borah@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patch.msgid.link/20260209133817.395823-1-imre.deak@intel.com
Commit ad121a62d5 ("drm/i915/dp: Rework pipe joiner logic in mode_valid")
replaced intel_dp_num_joined_pipes() with an explicit joiner candidate
iteration. The previous code implicitly checked for DP joiner capability
via intel_dp_has_joiner(), but this check was lost during the refactor.
Restore the missing intel_dp_has_joiner() check in intel_dp_can_join() so
that DP specific joiner conditions are taken into account.
v2: Derive intel_dp from intel_attached_dp(). (Imre)
Fixes: ad121a62d5 ("drm/i915/dp: Rework pipe joiner logic in mode_valid")
Cc: Ankit Nautiyal <ankit.k.nautiyal@intel.com>
Cc: Imre Deak <imre.deak@intel.com>
Signed-off-by: Ankit Nautiyal <ankit.k.nautiyal@intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Link: https://patch.msgid.link/20260206044753.808631-1-ankit.k.nautiyal@intel.com
intel_dp_can_join() was previously exposed in intel_dp.h, but after the
recent joiner refactor it is only used internally via
intel_dp_joiner_candidate_valid(). It no longer needs external
visibility, so make it static and drop the prototype from intel_dp.h.
Signed-off-by: Ankit Nautiyal <ankit.k.nautiyal@intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Link: https://patch.msgid.link/20260205083623.793902-2-ankit.k.nautiyal@intel.com
Update the device ID for Dell XPS 13 7390 2-in-1 in the quirk
`QUIRK_EDP_LIMIT_RATE_HBR2` entry. The previous ID (0x8a12) was
incorrect; the correct ID is 0x8a52.
Closes: https://gitlab.freedesktop.org/drm/i915/kernel/-/issues/5969
Fixes: 21c586d923 ("drm/i915/dp: Add device specific quirk to limit eDP rate to HBR2")
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Ankit Nautiyal <ankit.k.nautiyal@intel.com>
Cc: <stable@vger.kernel.org> # v6.18+
Signed-off-by: Ankit Nautiyal <ankit.k.nautiyal@intel.com>
Reviewed-by: Suraj Kandpal <suraj.kandpal@intel.com>
Link: https://patch.msgid.link/20251226043359.2553-1-ankit.k.nautiyal@intel.com
When enabling LRR/seamless MN disable LOBF first and re-enable
afterwards.
- pre_plane_update: if LOBF was enabled, disable LOBF before the
update_lrr/update_m_n transition.
- post_plane_update: Re-enable LOBF after the transition.
Signed-off-by: Ankit Nautiyal <ankit.k.nautiyal@intel.com>
Reviewed-by: Michał Grzelak <michal.grzelak@intel.com>
Link: https://patch.msgid.link/20260204050250.762718-6-ankit.k.nautiyal@intel.com
The pre_plane_update and post_plane_update hooks essentially
disable/enable lobf feature. Use the existing _is_enabling/is_disabling
logic for this in the pre_plane_update and post_plane_update paths.
Also rename the helpers to intel_alpm_lobf_{en,dis}able().
v2: Remove redeundant checks during enabling/disabling. (Jouni)
Signed-off-by: Ankit Nautiyal <ankit.k.nautiyal@intel.com>
Reviewed-by: Michał Grzelak <michal.grzelak@intel.com>
Reviewed-by: Jouni Högander <jouni.hogander@intel.com>
Link: https://patch.msgid.link/20260204050250.762718-5-ankit.k.nautiyal@intel.com
As per bspec the LOBF is allowed when running in fixed refresh rate mode
i.e. when flipline = vmin = vmax and when window1 is non zero. This
implies that we can allow LOBF only when VRR timing generator is running
in the fixed refresh rate mode.
Use the check intel_vrr_always_use_vrr_tg() to avoid LOBF with legacy
timing generator. Also use intel_vrr_is_fixed_rr() to check for fixed
refresh rate mode.
v2: Modify commit message to clarify window1 requirement for LOBF.
(Ville)
Signed-off-by: Ankit Nautiyal <ankit.k.nautiyal@intel.com>
Reviewed-by: Michał Grzelak <michal.grzelak@intel.com>
Link: https://patch.msgid.link/20260204050250.762718-4-ankit.k.nautiyal@intel.com
LOBF must be disabled if the number of lines within Window 1 is not greater
than ALPM_CTL[ALPM Entry Check]
v2: Consider the case where SCL is in the active region. (Ville)
Bspec:71041
Signed-off-by: Ankit Nautiyal <ankit.k.nautiyal@intel.com>
Reviewed-by: Michał Grzelak <michal.grzelak@intel.com>
Link: https://patch.msgid.link/20260204050250.762718-3-ankit.k.nautiyal@intel.com
Currently intel_alpm_lobf_compute_config() tries to account for
guardband +SCL requirements during encoder->compute_config() phase,
even before guardband is computed.
Also, LOBF depends on crtc_state->has_psr which can be modified in
encoder->compute_config_late().
Account for lobf requirements while optimizing the guardband and add
checks for final guardband in encoder->compute_config_late() phase after
the guardband and the final state of crtc_state->has_psr are already
computed.
Use crtc_state->vrr.guardband and crtc_state->set_context_latency for
the computation and add more documentation for the dependency of first
sdp position, guardband, set context latency and wake lines.
v2: Add helper to use min guardband required for lobf.
v3: Remove unrelated inadvertent changes. (Michał)
v4: Add a #FIXME note for computing wakelines based on feature. (Jouni)
Bspec:71041
Signed-off-by: Ankit Nautiyal <ankit.k.nautiyal@intel.com>
Reviewed-by: Michał Grzelak <michal.grzelak@intel.com>
Reviewed-by: Jouni Högander <jouni.hogander@intel.com>
Link: https://patch.msgid.link/20260204050250.762718-2-ankit.k.nautiyal@intel.com
TBT PHY is enablement/disablement is handled by its own TBT module.
We do not play a big part in it's state management, that being take care
by it's own TBT modeule.
The PHY/PLL TypeC mode (TBT, DP-alt) can change after the PLL state was
computed for a modeset, so the state verification after the modeset
sequence would indicate a mismatch in case the mode changed from DP-alt
to TBT, or from TBT to DP-alt mode. To avoid such a mismatch error the
verification is skipped if the mode for either the read-out or the
computed state is TBT (where that TBT PLL state doesn't reflect anyway
the PLL's actual HW state).
Simply return true when we are in tbt mode.
Signed-off-by: Suraj Kandpal <suraj.kandpal@intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Link: https://patch.msgid.link/20260204023247.1560196-1-suraj.kandpal@intel.com
Prevent display corruption observed after restart, hotplug, or unplug
operations on Meteor Lake and newer platforms. The issue is caused by
DSS clock gating affecting DSC logic when pipe power wells are disabled.
Apply this WA by disabling DSS clock gating for the affected pipes
before turning off their power wells. This avoids DSC corruption on
external displays.
v2: Use single intel_de_rmw() (Jani)
Switch to use drm_dbg_kms() instead of drm_printf() (Jani)
Remove WA number from commit message (Suraj)
rename dss_clock_gating_enable_disable() to
dss_pipe_gating_enable_disable();
v3: Do not use open ended display version when checking
wa (Matt)
WA: 22021048059
BSpec: 690991, 666241
Signed-off-by: Mika Kahola <mika.kahola@intel.com>
Reviewed-by: Suraj Kandpal <suraj.kandpal@intel.com>
Link: https://patch.msgid.link/20260202140242.704234-1-mika.kahola@intel.com
Add upper limit check for pixel clock for WCL.
For prior platforms though the bspec mentions the dotclock limits, however
these are intentionally not enforced to avoid regressions, unless real
issues are observed.
BSpec: 49199, 68912
Signed-off-by: Chaitanya Kumar Borah <chaitanya.kumar.borah@intel.com>
Signed-off-by: Ankit Nautiyal <ankit.k.nautiyal@intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Link: https://patch.msgid.link/20260202103731.357416-18-ankit.k.nautiyal@intel.com
Add upper limit check for pixel clock for DISPLAY_VER >= 30.
Limits don't apply when DSC is enabled.
The helper returns the upper limit for the platforms, capped to the
max dotclock (khz).
For the currently supported versions of HDMI, pixel clock is already
limited to 600Mhz so nothing needs to be done there as of now.
v2:
- Add this limit to the new helper.
v3:
- Rename helper to intel_max_uncompressed_dotclock(). (Imre)
- Limit only for PTL and cap the limit to max_dotclock. (Imre)
BSpec: 49199, 68912
Signed-off-by: Chaitanya Kumar Borah <chaitanya.kumar.borah@intel.com>
Signed-off-by: Ankit Nautiyal <ankit.k.nautiyal@intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Link: https://patch.msgid.link/20260202103731.357416-17-ankit.k.nautiyal@intel.com
Introduce for_each_joiner_candidate(), intel_dp_joiner_candidate_valid()
and intel_dp_joiner_candidate_valid() to remove duplicated joiner
enumeration and validity checks across DP SST and MST paths.
Suggested-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Ankit Nautiyal <ankit.k.nautiyal@intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Link: https://patch.msgid.link/20260202103731.357416-16-ankit.k.nautiyal@intel.com
Account for DSC slice overhead bubbles and adjust the pixel rate while
checking the pixel rate against the max dotclock limits.
v2: Add missing assignment for dsc_slice_count in
mst_connector_mode_valid_ctx(). (Imre)
v3: Explicitly pass dsc_slice_count as 0 for Non-DSC case. (Imre)
Signed-off-by: Ankit Nautiyal <ankit.k.nautiyal@intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Link: https://patch.msgid.link/20260202103731.357416-15-ankit.k.nautiyal@intel.com
Make dsc_slice_count closer to the block where it is used and promote it
from u8 to int. This aligns it with upcoming DSC bubble pixel-rate
adjustments, where the slice count participates in wider arithmetic.
Currently, for non-eDP (DP/DP_MST) cases the slice count is computed only
inside intel_dp_dsc_mode_valid() and is not used by the caller. Once DSC
bubble handling is added, dp_mode_valid() will need access to its own local
slice count for non-eDP cases as well.
Signed-off-by: Ankit Nautiyal <ankit.k.nautiyal@intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Link: https://patch.msgid.link/20260202103731.357416-14-ankit.k.nautiyal@intel.com
Add intel_dp_dotclk_valid() helper, that checks the required pixel rate
against platform dotclock limit. With joined pipes the effective dotclock
limit depends upon the number of joined pipes.
Call the helper from the mode_valid phase and from the compute_config
phase where we need to check the limits for the given target clock for a
given joiner candidate.
v2: Rename the helper to intel_dp_dotclk_valid(). (Imre)
Signed-off-by: Ankit Nautiyal <ankit.k.nautiyal@intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Link: https://patch.msgid.link/20260202103731.357416-13-ankit.k.nautiyal@intel.com
The helpers intel_dp_num_joined_pipes() and intel_dp_needs_joiner() are no
longer used now that joiner selection iterates over all candidates.
Remove them.
Signed-off-by: Ankit Nautiyal <ankit.k.nautiyal@intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Link: https://patch.msgid.link/20260202103731.357416-12-ankit.k.nautiyal@intel.com
Similar to the DP SST, refactor mst_stream_compute_config() to iterate
over joiner candidates and select the minimal joiner configuration that
satisfies the mode requirements. This prepares the logic for future changes
that will consider DSC slice overhead.
v2:
- Move the check for dotclock in the new helper and check for both DSC and
non-DSC case. In case the check fails for non-DSC, fallback to DSC
configuration. (Imre)
- Propagate the return value from the core helper:
mst_stream_compute_link_for_joined_pipes(). (Imre)
v3:
- Use num_joined_pipes instead of num_pipes. (Imre)
v4:
- Switch to 'ret == 0' for break condition to match SST code.
Signed-off-by: Ankit Nautiyal <ankit.k.nautiyal@intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Link: https://patch.msgid.link/20260202103731.357416-11-ankit.k.nautiyal@intel.com
Move the joiner-dependent portion of mst_stream_compute_config() into
mst_stream_compute_link_for_joined_pipes(), which computes the MST link
configuration for a specific num_joined_pipes.
Signed-off-by: Ankit Nautiyal <ankit.k.nautiyal@intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Link: https://patch.msgid.link/20260202103731.357416-10-ankit.k.nautiyal@intel.com
