When disconnecting single STA in AP, it might be that STA
in question is already disconnected. In this case, need to do nothing.
Previously, it was mis-interpreted as "disconnect all"
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
When printing debugfs for the reorder buffer, include BACK
parameters: window size and timeout
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
For manual ADDBA configuration, allow to set desired window size or
disable automatic mechanism.
Introduce module parameter (int) agg_wsize. It can be changed on run time,
will be taken into account on the next connect. Interpretation:
- <0 - disable automatic ADDBA; intended for manual testing through debugfs
- 0 - use automatically calculated window size
- >0 - use this for window size. Clipped by maximum supported by the hardware
with current environment.
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Upon Tx vring creation, initiate BACK establishment
with maximum possible window size.
When establishing secure connection, there is EAPOL data exchange
between connection itself and "data port open", where security
is done and non-EAPOL data may be transferred. It is better to
send EAPOL frames using normal ACK because of firmware considerations.
send ADDBA only is 2 conditions met:
- data port open for the corresponded STA
- vring created
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Introduce BACK establishment procedures; decision logic is not implemented
yet; debugfs entry 'addba' used to manually trigger addba/delba for ringid 0.
debugfs usage:
to establish BACK with agg_wsize 16:
echo 16 > /sys/kernel/debug/ieee80211/phy0/wil6210/addba
to delete BACK:
echo 0 > /sys/kernel/debug/ieee80211/phy0/wil6210/addba
to change agg_wsize, one need to delete BACK and establish it anew
ADDBA flow for:
- originator
Tx side (initiator) sends WMI_VRING_BA_EN_CMDID providing
agg_wsize and timeout parameters.
Eventually, it gets event confirming BACK agreement - WMI_BA_STATUS_EVENTID
with negotiated parameters. On this event, update Tx vring data
(struct vring_tx_data) and display BACK parameters on debugfs
- recipient
Rx side (recipient) firmware informs driver about ADDBA with
WMI_RCP_ADDBA_REQ_EVENTID, driver process it in service work
queue wq_service. It adjusts parameters and sends response
with WMI_RCP_ADDBA_RESP_CMDID, and final confirmation provided
by firmware with WMI_ADDBA_RESP_SENT_EVENTID. In case of success,
driver updates Rx BACK reorder buffer.
policy for BACK parameters:
- aggregation size (agg_wsize * MPDUsize)) to not exceed 64Kbytes
DELBA flow for:
- originator
driver decides to terminate BACK, it sends WMI_VRING_BA_DIS_CMDID
and updates struct vring_tx_data associated with vring; ignore
WMI_DELBA_EVENTID.
- recipient
firmware informs driver with WMI_DELBA_EVENTID,
driver deletes correspondent reorder buffer
ADDBA request processing requires sending WMI command, therefore
it is processed in work queue context. Same work queue used as for
connect, it get renamed to wq_service
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Miaoqing Pan <miaoqing@qca.qualcomm.com>
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Miaoqing Pan <miaoqing@qca.qualcomm.com>
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Miaoqing Pan <miaoqing@qca.qualcomm.com>
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Miaoqing Pan <miaoqing@qca.qualcomm.com>
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
To aid the developer when something triggers an unexpected exception,
decode the ESR_ELx.EC field when logging an ESR_ELx value using the
newly introduced esr_get_class_string. This doesn't tell the developer
the specifics of the exception encoded in the remaining IL and ISS bits,
but it can be helpful to distinguish between exception classes (e.g.
SError and a data abort) without having to manually decode the field,
which can be tiresome.
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Acked-by: Christoffer Dall <christoffer.dall@linaro.org>
Reviewed-by: Christoffer Dall <christoffer.dall@linaro.org>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Peter Maydell <peter.maydell@linaro.org>
Cc: Will Deacon <will.deacon@arm.com>
Now that all users have been moved over to the common ESR_ELx_* macros,
remove the redundant ESR_EL2 macros. To maintain compatibility with the
fault handling code shared with 32-bit, the FSC_{FAULT,PERM} macros are
retained as aliases for the common ESR_ELx_FSC_{FAULT,PERM} definitions.
There should be no functional change as a result of this patch.
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Acked-by: Christoffer Dall <christoffer.dall@linaro.org>
Reviewed-by: Christoffer Dall <christoffer.dall@linaro.org>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Peter Maydell <peter.maydell@linaro.org>
Cc: Will Deacon <will.deacon@arm.com>
Now that all users have been moved over to the common ESR_ELx_* macros,
remove the redundant ESR_EL1 macros.
There should be no functional change as a result of this patch.
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Reviewed-by: Christoffer Dall <christoffer.dall@linaro.org>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Peter Maydell <peter.maydell@linaro.org>
Cc: Will Deacon <will.deacon@arm.com>
Now that we have common ESR_ELx macros, make use of them in the arm64
KVM code. The addition of <asm/esr.h> to the include path highlighted
badly ordered (i.e. not alphabetical) include lists; these are changed
to alphabetical order.
There should be no functional change as a result of this patch.
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Reviewed-by: Christoffer Dall <christoffer.dall@linaro.org>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Peter Maydell <peter.maydell@linaro.org>
Cc: Will Deacon <will.deacon@arm.com>
To aid the developer when something triggers an unexpected exception,
decode the ESR_ELx.EC field when logging an ESR_ELx value. This doesn't
tell the developer the specifics of the exception encoded in the
remaining IL and ISS bits, but it can be helpful to distinguish between
exception classes (e.g. SError and a data abort) without having to
manually decode the field, which can be tiresome.
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Reviewed-by: Christoffer Dall <christoffer.dall@linaro.org>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Peter Maydell <peter.maydell@linaro.org>
Cc: Will Deacon <will.deacon@arm.com>
Now that we have common ESR_ELx_* macros, move the core arm64 code over
to them.
There should be no functional change as a result of this patch.
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Reviewed-by: Christoffer Dall <christoffer.dall@linaro.org>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Peter Maydell <peter.maydell@linaro.org>
Cc: Will Deacon <will.deacon@arm.com>
Currently we have separate ESR_EL{1,2}_* macros, despite the fact that
the encodings are common. While encodings are architected to refer to
the current EL or a lower EL, the macros refer to particular ELs (e.g.
ESR_ELx_EC_DABT_EL0). Having these duplicate definitions is redundant,
and their naming is misleading.
This patch introduces common ESR_ELx_* macros that can be used in all
cases, in preparation for later patches which will migrate existing
users over. Some additional cleanups are made in the process:
* Suffixes for particular exception levelts (e.g. _EL0, _EL1) are
replaced with more general _LOW and _CUR suffixes, matching the
architectural intent.
* ESR_ELx_EC_WFx, rather than ESR_ELx_EC_WFI is introduced, as this
EC encoding covers traps from both WFE and WFI. Similarly,
ESR_ELx_WFx_ISS_WFE rather than ESR_ELx_EC_WFI_ISS_WFE is introduced.
* Multi-bit fields are given consistently named _SHIFT and _MASK macros.
* UL() is used for compatiblity with assembly files.
* Comments are added for currently unallocated ESR_ELx.EC encodings.
For fields other than ESR_ELx.EC, macros are only implemented for fields
for which there is already an ESR_EL{1,2}_* macro.
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Reviewed-by: Christoffer Dall <christoffer.dall@linaro.org>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Peter Maydell <peter.maydell@linaro.org>
Cc: Will Deacon <will.deacon@arm.com>
Currently the trace printk talks about "wfi" only, though the trace
point triggers both on wfi and wfe traps.
Add a parameter to differentiate between the two.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Wei Huang <wei@redhat.com>
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>
* A fix that improves roaming behavior. Same fix has been tested for
a while in iwldvm. This is a bit of a work around, but the real fix
should be in mac80211 and will come later.
* A fix for BARs that avoids a WARNING.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQIcBAABAgAGBQJUtMJGAAoJEC0Llv5uNjIBqoYP/iH29kX1NpmdGRIt3KEASCQn
mr/JBR4MVBlx4UQJhXQBQnUYmDOzZ1CvQISnVheHZCfZFvbuxEGxh8CxgSmMTEhR
2BmByuAxDma2XCxla9OIZJCkQt+eu9Wsdy5AcOkkBmnbuNFMWIFILamMAyGBFXwo
ZAw9b+c+YsywtEYGSiZF07OXGUIs2oLWPQ7iHJLkTAlOQfKG5QSlQ+DB3BqI9kf8
x8lM7ZuiSEyJkwV7MJogd7NpDUKtbu+mb7KUdvGYffknyakYh5pVN/0aUAnL8Xhj
zdWQV8v7CjaHP68mliktdD03KXVi609XIV+oKzB4PBJCQDjoYAIqabYY7FuO3iSj
4a+8lh3O9InkQclOJNzNAJFQlHVs1EbeiWVddLe7X1RyRofO6BgyOxj/G3gnWpQI
KKRWS4EQyQrXehyygmEVUMMl2Mv4URQoQ0eyWKlkjNnLGjzinuTXAezFcjEhjY/f
W7XCRACf0w+eLtXKd3etn3T+uGzaKHs8EhapGl6psYjUKMaGLBDvtT8Wie8qkvHM
JJpxHGyE5nn2i4tdTQWQ5gg1fj8LfFXljcRu1MVq4zzjcqOP4mbLO+yfDFX2iDFQ
ez2Oy+3IvjJ8Sw4D1y/5/dYmEXDTbkyjb+eBmYxG1ui62RViJUdbmVGwpLsucowT
qGKlBtY3eEcHSYsEcBV/
=9GPb
-----END PGP SIGNATURE-----
Merge tag 'iwlwifi-for-kalle-2015-01-13' of https://git.kernel.org/pub/scm/linux/kernel/git/iwlwifi/iwlwifi-fixes
* A fix for scan that fixes a firmware assertion
* A fix that improves roaming behavior. Same fix has been tested for
a while in iwldvm. This is a bit of a work around, but the real fix
should be in mac80211 and will come later.
* A fix for BARs that avoids a WARNING.
There are no more users of this field left so it can finally be removed.
New users should use snd_soc_dapm_to_codec(w->dapm);
The reason why it is removed is because it doesn't fit to well anymore in
the componentized ASoC hierarchy, where DAPM works on the snd_soc_component
level. And the alternative of snd_soc_dapm_to_codec(w->dapm) typically
generates the same amount of code, so there is really no reason to keep it.
For automatic conversion the following coccinelle semantic patch can be used:
// <smpl>
@@
struct snd_soc_dapm_widget *w;
@@
-w->codec
+snd_soc_dapm_to_codec(w->dapm)
// </smpl>
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
The codec field of the snd_soc_widget struct is eventually going to be
removed, use snd_soc_dapm_to_codec(w->dapm) instead.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
The codec field of the snd_soc_widget struct is eventually going to be
removed, use snd_soc_dapm_to_codec(w->dapm) instead.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
The codec field of the snd_soc_widget struct is eventually going to be
removed, use snd_soc_dapm_to_codec(w->dapm) instead.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
The codec field of the snd_soc_widget struct is eventually going to be
removed, use snd_soc_dapm_to_codec(w->dapm) instead.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
The codec field of the snd_soc_widget struct is eventually going to be
removed, use snd_soc_dapm_to_codec(w->dapm) instead.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
The codec field of the snd_soc_widget struct is eventually going to be
removed, use snd_soc_dapm_to_codec(w->dapm) instead.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
The codec field of the snd_soc_widget struct is eventually going to be
removed, use snd_soc_dapm_to_codec(w->dapm) instead.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
The codec field of the snd_soc_widget struct is eventually going to be
removed, use snd_soc_dapm_to_codec(w->dapm) instead.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
The codec field of the snd_soc_widget struct is eventually going to be
removed, use snd_soc_dapm_to_codec(w->dapm) instead.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
The codec field of the snd_soc_widget struct is eventually going to be
removed, use snd_soc_dapm_to_codec(w->dapm) instead.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
The codec field of the snd_soc_widget struct is eventually going to be
removed, use snd_soc_dapm_to_codec(w->dapm) instead.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
The codec field of the snd_soc_widget struct is eventually going to be
removed, use snd_soc_dapm_to_codec(w->dapm) instead.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
The codec field of the snd_soc_widget struct is eventually going to be
removed, use snd_soc_dapm_to_codec(w->dapm) instead.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
The codec field of the snd_soc_widget struct is eventually going to be
removed, use snd_soc_dapm_to_codec(w->dapm) instead.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
The codec field of the snd_soc_widget struct is eventually going to be
removed, use snd_soc_dapm_to_codec(w->dapm) instead.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
Commit f6b2a04590 ("ASoC: pxa: mioa701_wm9713: Convert to table based DAPM
setup") converted the driver to register the board level DAPM elements with
the card's DAPM context rather than the CODEC's DAPM context. The change
overlooked that the speaker widget event callback accesses the widget's
codec field which is only valid if the widget has been registered in a CODEC
DAPM context. This patch modifies the callback to take an alternative route
to get the CODEC.
Fixes: f6b2a04590 ("ASoC: pxa: mioa701_wm9713: Convert to table based DAPM
setup")
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch adds support for cacheinfo on ARM64.
On ARMv8, the cache hierarchy can be identified through Cache Level ID
(CLIDR) register while the cache geometry is provided by Cache Size ID
(CCSIDR) register.
Since the architecture doesn't provide any way of detecting the cpus
sharing particular cache, device tree is used for the same purpose.
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Call clk_prepare_enable() and clk_disable_unprepare() for cpu dai
clock and codec dai clock in dai statup and shutdown callbacks. This
to make sure the related clock are enabled when the audio device is
used.
Signed-off-by: Jyri Sarha <jsarha@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
arm64 uses its own copy of exit handler (arm64/kvm/handle_exit.c).
Currently this file doesn't hook up with any trace points. As a result
users might not see certain events (e.g. HVC & WFI) while using ftrace
with arm64 KVM. This patch fixes this issue by adding a new trace file
and defining two trace events (one of which is shared by wfi and wfe)
for arm64. The new trace points are then linked with related functions
in handle_exit.c.
Signed-off-by: Wei Huang <wei@redhat.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>
Current R-Car sound driver calls SRC -> SSI -> DVC functions,
but, it should be DVC -> SRC -> SSI.
Otherwise, SSI (= interface of codec) will have underrun error
when playback.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Current DMA starts after SSI, and stops before SSI. but we need
to reverse these order. Otherwise, under/over run error might happen.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
SSI interrupt handler of R-Car sound driver will be called
when DIRQ (= Data read/write timing for PIO) or
UIRQ / OIRQ (= under/over run error).
DIRQ "interrupt" doesn't occur when DMA transfer, but then,
DIRQ "status bit" might occur. we need to ignore this DIRQ
operation when DMA. Otherwise, driver will push/pop as PIO.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Current SRC/SSI output its error, but it desn't indicate
port number. it is un-understandable.
Let's indicate port number for it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Current rsnd driver has rsnd_mod_to_priv() macro, and struct rsnd_mod
has struct rsnd_priv pointer. But, it is waste of memory from data
structure point of view.
Today we can link mod <-> io <-> rdai each other, so saving priv in
rdai is very reasonable.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Current rsnd driver's function requests rdai, but it is not used.
Adding priv is more reasonable. Let's replace it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Current rsnd driver's many functions requests struct rsnd_dai (= rdai),
but, 1) we can get rdai from rsnd_io_to_rsnd(), 2) almost all rdai
is not used. Let's remove these rdai.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Current rsnd driver can use rsnd_io_to_rdai()
we can get play/capture direction via io now.
Let's replace rsnd_dai_is_play() to rsnd_io_is_play()
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Current rsnd driver request rdai in everywhere, but each mod should
reach to rdai by itself. this patch adds missing rsnd_io_to_rdai().
io = rsnd_mod_to_io(mod);
rdai = rsnd_io_to_rdai(io);
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
rsnd_dai_get_platform_info() is not used. Let's remove it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
rsnd_dai_id() was not used. Let's remove it
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
