struct rsnd_dai is called as "rdai", and struct snd_soc_dai is called
as "dai" on this driver. but macro/function have confusable naming.
This patch rename rsnd_dai_is_clk_master() to rsnd_rdai_is_clk_master()
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
struct rsnd_dai is called as "rdai", and struct snd_soc_dai is called
as "dai" on this driver. but macro/function have confusable naming.
This patch rename rsnd_dai_get() to rsnd_rdai_get()
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Current rsnd driver's mod (= ssi/src/dvc) have each own clk,
but, these are needed to start/stop each mod.
This patch adds struct clk in rsnd_mod, and start/stop these
via rsnd_mod_hw_start/stop() macro
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
rsnd_ssi::rate is not used. Let's remove it
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
fbmon may generate mode timings that are out of spec of the monitor.
eg DELL U2410 has a max clock 170mhz but advertises a resolutions of
1920x1200@60 in its Standard Timings using 2byte code of D1 00.
When this is looked up in the DMT table it gives it a 193mhz clock.
Although the DELL monitor supports 1920x1200@60, it can only run with
reduced timings at 154mhz or DMT id 0x44 which has no STD 2byte code.
This patch checks to see if the mode can be supported by the monitor
by comparing against monspecs.dclkmax.
Signed-off-by: David Ung <davidu@nvidia.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Add the VESA Display Monitor Timing (DMT) table.
During parsing of Standard Timings, it compare the 2 byte STD code
with DMT to see what the VESA mode should be. If there is no entry
in the vesa_modes table or no match found, it fallsback to the
GTF timings.
Signed-off-by: David Ung <davidu@nvidia.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
this patch sets the default height if its not found in DT.
Signed-off-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
this patch drops the unused function ssd1307fb_write_data().
Signed-off-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
There is only one I2S I/F, AD/DA path must operate to the same
format.
Signed-off-by: Bard Liao <bardliao@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
When the controller gets powered on via the management interface, then
register the supported SMP channels. There is no point in registering
these channels earlier since it is not know what identity address the
controller is going to operate with.
When powering down a controller unregister all SMP channels. This is
required since a powered down controller is allowed to change its
identity address.
In addition the SMP channels are only available when the controller
is powered via the management interface. When using legacy ioctl, then
Bluetooth Low Energy is not supported and registering kernel side SMP
integration may actually cause confusion.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
When LE features are not supported, then do not bother registering any
kind of SMP channel.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The source address and source address type of the LE SMP channel can
either be the public address of the controller or the static random
address configured by the host.
Right now the public address is used for the LE SMP channel and
obviously that is not correct if the controller operates with the
configured static random address.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
To be compliant with the hwmon interface the unit needs to be
millidegree Celsius. Fix that.
Reported-by: Matthias Kaehlcke <mka@google.com>
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Add a comment for indicating that the ATH10K_SCAN_RUNNING case falls
through to the ATH10K_SCAN_ABORTING case in __ath10k_scan_finish. This
will document that the lack of a break is intentional.
Coverity: CID 1260017
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Originally the explicit fw register dump was added
to wait_for_target_init because interrupts are
masked early during power_up.
Due to some changes in power_up/reset sequences
sometimes when fw crashed ath10k would print the
dump more than once via hif_stop -> warm_reset ->
wait_for_target_init, possibly with different
values each.
Prevent this by doing the explicit fw register
dump only during power_up instead of
wait_for_target_init.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The duty cycle (% of quiet duration) is used to put the device
in quiet mode for the given period. Currently the quiet duration
is wrongly calculated which results in not enabling quiet mode.
Fix the calculation as below
duration = (period * duty cycle) / 100
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
access the mmcfg space - some error injection functions need to do
this.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQIcBAABAgAGBQJUtWbqAAoJEKurIx+X31iBNjAP/1Yi3zKx87NmYf2juuhKKeo/
39Pap/qw0BngSYcNh1okMFh7LdpPdQrGc/EN9/kprU9IgafiUeQHRUXyHy1OzMaI
Ud6c4BiYBcfvVp81xCvfKiSUjAMB++vIamyt4daoDWqAhn0+MBNTgFoR1Nsyu9Pb
bhp39n7kHQjyxTsfPnN5iBN3+fBz1zPJAWWGoPSfnL/MP3tossqlPRDqThF/BY2J
lUe2BdASOx++ojE5fDPoeiJhvB/8Hovy4eN543qNvpAitBwBJLGlMcxlMEcYN3QQ
skbML9ZQ4ipoLlWZ9i2siiLVF7Y2ME3/NbBGgquTZ8U3Kqi0kgCEePOFVnvxMfhA
MFYVyc8lW72X8WyHdJXY0aHCyq6QFWfhiu7j/eu6bCbQnVqHWhMblzk2eEpPWwRV
jK9arCHZGik9c9cYZJq+WzIukyrtJR1D+4jAcQyxUjR/wQJ1CLCe5xuDZUfiLDno
GVwdarBoD1dtLIA4noc0VXwjVN51lS1MTBR7TL/cu6hj+p2Tq6FXa7QW30a80Udq
3fm2HdzhQEmfUAi2EznwZwtuy0Pt5c2DIAl/Ie4GDMJX19MuvKRRSt6SDCY+YSSQ
SJB3iXm0t99MkIJrwycaQEb190DtFbVYk+gT26TtPrIuHbd5Y/5hwv0J+wSEDwom
ErFpiJEhK6hnBdV+eHxB
=3MwK
-----END PGP SIGNATURE-----
Merge tag 'please-pull-einj-mmcfg' of git://git.kernel.org/pub/scm/linux/kernel/git/ras/ras into x86/ras
Pull RAS update from Tony Luck:
"When checking addresses in APEI action entries for validity, allow
access to the mmcfg space - some error injection functions need to do
this."
Signed-off-by: Ingo Molnar <mingo@kernel.org>
New firmware revisions support beacon and probe
response templates instead. This means SWBA events
are no longer delivered for these firmware
revisions.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Along beacon template host is expected to setup
p2p information elements as well. Implement wmi
interface for it.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
New firmware revisions with beacon templates need
probe templates as well because they don't forward
probe requests to host at all.
This is required for new firmware to work with
direct probe requests (notably required by hidden
ssid AP).
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
New firmware revisions may support setting beacon
template. Implement wmi interface for it.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
This event is delivered to host by firmware if it
supports beacon templates only.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
and a cleanup from me.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=r9gb
-----END PGP SIGNATURE-----
Merge tag 'ras_for_3.20' of git://git.kernel.org/pub/scm/linux/kernel/git/bp/bp into x86/ras
Pull RAS updates from Borislav Petkov:
"Nothing special this time, just an error messages improvement from Andy
and a cleanup from me."
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Refine code by normailizing the way to detect whether IR is enabled.
Signed-off-by: Jiang Liu <jiang.liu@linux.intel.com>
Tested-by: Joerg Roedel <joro@8bytes.org>
Cc: Tony Luck <tony.luck@intel.com>
Cc: iommu@lists.linux-foundation.org
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Yinghai Lu <yinghai@kernel.org>
Cc: Borislav Petkov <bp@alien8.de>
Link: http://lkml.kernel.org/r/1420615903-28253-17-git-send-email-jiang.liu@linux.intel.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Change variable disable_irq_remap to be static and simplify the code.
Signed-off-by: Jiang Liu <jiang.liu@linux.intel.com>
Tested-by: Joerg Roedel <joro@8bytes.org>
Cc: Tony Luck <tony.luck@intel.com>
Cc: iommu@lists.linux-foundation.org
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Yinghai Lu <yinghai@kernel.org>
Cc: Borislav Petkov <bp@alien8.de>
Link: http://lkml.kernel.org/r/1420615903-28253-16-git-send-email-jiang.liu@linux.intel.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Assign intel_irq_remap_ops to remap_ops only if
intel_irq_remap_ops.prepare() succeeds.
Signed-off-by: Jiang Liu <jiang.liu@linux.intel.com>
Tested-by: Joerg Roedel <joro@8bytes.org>
Cc: Tony Luck <tony.luck@intel.com>
Cc: iommu@lists.linux-foundation.org
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Yinghai Lu <yinghai@kernel.org>
Cc: Borislav Petkov <bp@alien8.de>
Link: http://lkml.kernel.org/r/1420615903-28253-15-git-send-email-jiang.liu@linux.intel.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Simplify irq_remapping code by killing irq_remapping_supported() and
related interfaces.
Joerg posted a similar patch at https://lkml.org/lkml/2014/12/15/490,
so assume an signed-off from Joerg.
Signed-off-by: Jiang Liu <jiang.liu@linux.intel.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Tested-by: Joerg Roedel <joro@8bytes.org>
Cc: Tony Luck <tony.luck@intel.com>
Cc: iommu@lists.linux-foundation.org
Cc: H. Peter Anvin <hpa@linux.intel.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Yinghai Lu <yinghai@kernel.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: David Rientjes <rientjes@google.com>
Cc: HATAYAMA Daisuke <d.hatayama@jp.fujitsu.com>
Cc: Jan Beulich <JBeulich@suse.com>
Cc: Richard Weinberger <richard@nod.at>
Cc: Oren Twaig <oren@scalemp.com>
Link: http://lkml.kernel.org/r/1420615903-28253-14-git-send-email-jiang.liu@linux.intel.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
This allows to get rid of the irq_remapping_supported() function and
all its call-backs into the Intel and AMD IOMMU drivers.
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Signed-off-by: Jiang Liu <jiang.liu@linux.intel.com>
Tested-by: Joerg Roedel <joro@8bytes.org>
Cc: Tony Luck <tony.luck@intel.com>
Cc: iommu@lists.linux-foundation.org
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Yinghai Lu <yinghai@kernel.org>
Cc: Borislav Petkov <bp@alien8.de>
Link: http://lkml.kernel.org/r/1420615903-28253-13-git-send-email-jiang.liu@linux.intel.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
When interrupt remapping hardware is not in X2APIC, CPU X2APIC mode
will be disabled if:
1) Maximum CPU APIC ID is bigger than 255
2) hypervisior doesn't support x2apic mode.
But we should only check whether hypervisor supports X2APIC mode when
hypervisor(CONFIG_HYPERVISOR_GUEST) is enabled, otherwise X2APIC will
always be disabled when CONFIG_HYPERVISOR_GUEST is disabled and IR
doesn't work in X2APIC mode.
Signed-off-by: Jiang Liu <jiang.liu@linux.intel.com>
Tested-by: Joerg Roedel <joro@8bytes.org>
Cc: Tony Luck <tony.luck@intel.com>
Cc: iommu@lists.linux-foundation.org
Cc: H. Peter Anvin <hpa@linux.intel.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Yinghai Lu <yinghai@kernel.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: David Rientjes <rientjes@google.com>
Cc: HATAYAMA Daisuke <d.hatayama@jp.fujitsu.com>
Cc: Jan Beulich <JBeulich@suse.com>
Cc: Richard Weinberger <richard@nod.at>
Cc: Oren Twaig <oren@scalemp.com>
Link: http://lkml.kernel.org/r/1420615903-28253-12-git-send-email-jiang.liu@linux.intel.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Currently if CPU supports X2APIC, IR hardware must work in X2APIC mode
or disabled. Change the code to support IR working in XAPIC mode when
CPU supports X2APIC. Then the CPU APIC driver will decide how to handle
such as configuration by:
1) Disabling X2APIC mode
2) Forcing X2APIC physical mode
This change also fixes a live locking when
1) BIOS enables CPU X2APIC
2) DMAR table disables X2APIC mode or IR hardware doesn't support X2APIC
with following messages:
[ 37.863463] dmar: INTR-REMAP: Request device [[f0:1f.7] fault index 2
[ 37.863463] INTR-REMAP:[fault reason 36] Detected reserved fields in the IRTE entry
[ 37.879372] dmar: INTR-REMAP: Request device [[f0:1f.7] fault index 2
[ 37.879372] INTR-REMAP:[fault reason 36] Detected reserved fields in the IRTE entry
[ 37.895282] dmar: INTR-REMAP: Request device [[f0:1f.7] fault index 2
[ 37.895282] INTR-REMAP:[fault reason 36] Detected reserved fields in the IRTE entry
[ 37.911192] dmar: INTR-REMAP: Request device [[f0:1f.7] fault index 2
Signed-off-by: Jiang Liu <jiang.liu@linux.intel.com>
Tested-by: Joerg Roedel <joro@8bytes.org>
Cc: Tony Luck <tony.luck@intel.com>
Cc: iommu@lists.linux-foundation.org
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Yinghai Lu <yinghai@kernel.org>
Cc: Borislav Petkov <bp@alien8.de>
Link: http://lkml.kernel.org/r/1420615903-28253-11-git-send-email-jiang.liu@linux.intel.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
IRQ remapping is only supported when all IOMMUs in the
system support it. So check if all IOMMUs in the system
support IRQ remapping before doing the allocations.
[Jiang]
1) Rebased to v3.19.
2) Remove redundant check of ecap_ir_support(iommu->ecap) in function
intel_enable_irq_remapping().
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Signed-off-by: Jiang Liu <jiang.liu@linux.intel.com>
Tested-by: Joerg Roedel <joro@8bytes.org>
Cc: Tony Luck <tony.luck@intel.com>
Cc: iommu@lists.linux-foundation.org
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Yinghai Lu <yinghai@kernel.org>
Cc: Borislav Petkov <bp@alien8.de>
Link: http://lkml.kernel.org/r/1420615903-28253-10-git-send-email-jiang.liu@linux.intel.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Prepare for killing function irq_remapping_supported() by moving code
from intel_irq_remapping_supported() into intel_prepare_irq_remapping().
Combined with patch from Joerg at https://lkml.org/lkml/2014/12/15/487,
so assume an signed-off from Joerg.
Signed-off-by: Jiang Liu <jiang.liu@linux.intel.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Tested-by: Joerg Roedel <joro@8bytes.org>
Cc: Tony Luck <tony.luck@intel.com>
Cc: iommu@lists.linux-foundation.org
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Yinghai Lu <yinghai@kernel.org>
Cc: Borislav Petkov <bp@alien8.de>
Link: http://lkml.kernel.org/r/1420615903-28253-9-git-send-email-jiang.liu@linux.intel.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
If remapping is in XAPIC mode, the setup code just skips X2APIC
initialization without checking max CPU APIC ID in system, which may
cause problem if system has a CPU with APIC ID bigger than 255.
Handle IR in XAPIC mode the same way as if remapping is disabled.
[ tglx: Split out from previous patch ]
Signed-off-by: Jiang Liu <jiang.liu@linux.intel.com>
Cc: Tony Luck <tony.luck@intel.com>
Cc: iommu@lists.linux-foundation.org
Cc: H. Peter Anvin <hpa@linux.intel.com>
Cc: Joerg Roedel <joro@8bytes.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Yinghai Lu <yinghai@kernel.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: David Rientjes <rientjes@google.com>
Cc: HATAYAMA Daisuke <d.hatayama@jp.fujitsu.com>
Cc: Jan Beulich <JBeulich@suse.com>
Cc: Richard Weinberger <richard@nod.at>
Cc: Oren Twaig <oren@scalemp.com>
Link: http://lkml.kernel.org/r/1420615903-28253-8-git-send-email-jiang.liu@linux.intel.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Refine enable_IR_x2apic() and related functions for better readability.
[ tglx: Removed the XAPIC mode change and split it out into a seperate
patch. Added comments. ]
Signed-off-by: Jiang Liu <jiang.liu@linux.intel.com>
Cc: Tony Luck <tony.luck@intel.com>
Cc: iommu@lists.linux-foundation.org
Cc: H. Peter Anvin <hpa@linux.intel.com>
Cc: Joerg Roedel <joro@8bytes.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Yinghai Lu <yinghai@kernel.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: David Rientjes <rientjes@google.com>
Cc: HATAYAMA Daisuke <d.hatayama@jp.fujitsu.com>
Cc: Jan Beulich <JBeulich@suse.com>
Cc: Richard Weinberger <richard@nod.at>
Cc: Oren Twaig <oren@scalemp.com>
Link: http://lkml.kernel.org/r/1420615903-28253-8-git-send-email-jiang.liu@linux.intel.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
X2APIC will be disabled if user specifies "nox2apic" on kernel command
line, even when x2apic_preenabled is true. So correctly detect X2APIC
status by using x2apic_enabled() instead of x2apic_preenabled.
Signed-off-by: Jiang Liu <jiang.liu@linux.intel.com>
Cc: Tony Luck <tony.luck@intel.com>
Cc: iommu@lists.linux-foundation.org
Cc: H. Peter Anvin <hpa@linux.intel.com>
Cc: Joerg Roedel <joro@8bytes.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Yinghai Lu <yinghai@kernel.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: David Rientjes <rientjes@google.com>
Cc: HATAYAMA Daisuke <d.hatayama@jp.fujitsu.com>
Cc: Jan Beulich <JBeulich@suse.com>
Cc: Richard Weinberger <richard@nod.at>
Cc: Oren Twaig <oren@scalemp.com>
Link: http://lkml.kernel.org/r/1420615903-28253-7-git-send-email-jiang.liu@linux.intel.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Local variable x2apic_enabled has been assigned to but never referred,
so kill it.
Signed-off-by: Jiang Liu <jiang.liu@linux.intel.com>
Cc: Tony Luck <tony.luck@intel.com>
Cc: iommu@lists.linux-foundation.org
Cc: H. Peter Anvin <hpa@linux.intel.com>
Cc: Joerg Roedel <joro@8bytes.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Yinghai Lu <yinghai@kernel.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: David Rientjes <rientjes@google.com>
Cc: HATAYAMA Daisuke <d.hatayama@jp.fujitsu.com>
Cc: Jan Beulich <JBeulich@suse.com>
Cc: Richard Weinberger <richard@nod.at>
Cc: Oren Twaig <oren@scalemp.com>
Link: http://lkml.kernel.org/r/1420615903-28253-6-git-send-email-jiang.liu@linux.intel.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
When kernel doesn't support X2APIC but BIOS has enabled X2APIC, system
may panic or hang without useful messages. On the other hand, it's
hard to dynamically disable X2APIC when CONFIG_X86_X2APIC is disabled.
So panic with a clear message in such a case.
Now system panics as below when X2APIC is disabled and interrupt remapping
is enabled:
[ 0.316118] LAPIC pending interrupts after 512 EOI
[ 0.322126] ..TIMER: vector=0x30 apic1=0 pin1=2 apic2=-1 pin2=-1
[ 0.368655] Kernel panic - not syncing: timer doesn't work through Interrupt-remapped IO-APIC
[ 0.378300] CPU: 0 PID: 1 Comm: swapper/0 Not tainted 3.18.0+ #340
[ 0.385300] Hardware name: Intel Corporation BRICKLAND/BRICKLAND, BIOS BRIVTIN1.86B.0051.L05.1406240953 06/24/2014
[ 0.396997] ffff88046dc03000 ffff88046c307dd8 ffffffff8179dada 00000000000043f2
[ 0.405629] ffffffff81a92158 ffff88046c307e58 ffffffff8179b757 0000000000000002
[ 0.414261] 0000000000000008 ffff88046c307e68 ffff88046c307e08 ffffffff813ad82b
[ 0.422890] Call Trace:
[ 0.425711] [<ffffffff8179dada>] dump_stack+0x45/0x57
[ 0.431533] [<ffffffff8179b757>] panic+0xc1/0x1f5
[ 0.436978] [<ffffffff813ad82b>] ? delay_tsc+0x3b/0x70
[ 0.442910] [<ffffffff8166fa2c>] panic_if_irq_remap+0x1c/0x20
[ 0.449524] [<ffffffff81d73645>] setup_IO_APIC+0x405/0x82e
[ 0.464979] [<ffffffff81d6fcc2>] native_smp_prepare_cpus+0x2d9/0x31c
[ 0.472274] [<ffffffff81d5d0ac>] kernel_init_freeable+0xd6/0x223
[ 0.479170] [<ffffffff81792ad0>] ? rest_init+0x80/0x80
[ 0.485099] [<ffffffff81792ade>] kernel_init+0xe/0xf0
[ 0.490932] [<ffffffff817a537c>] ret_from_fork+0x7c/0xb0
[ 0.497054] [<ffffffff81792ad0>] ? rest_init+0x80/0x80
[ 0.502983] ---[ end Kernel panic - not syncing: timer doesn't work through Interrupt-remapped IO-APIC
System hangs as below when X2APIC and interrupt remapping are both disabled:
[ 1.102782] pci 0000:00:02.0: System wakeup disabled by ACPI
[ 1.109351] pci 0000:00:03.0: System wakeup disabled by ACPI
[ 1.115915] pci 0000:00:03.2: System wakeup disabled by ACPI
[ 1.122479] pci 0000:00:03.3: System wakeup disabled by ACPI
[ 1.132274] pci 0000:00:1c.0: Enabling MPC IRBNCE
[ 1.137620] pci 0000:00:1c.0: Intel PCH root port ACS workaround enabled
[ 1.145239] pci 0000:00:1c.0: System wakeup disabled by ACPI
[ 1.151790] pci 0000:00:1c.7: Enabling MPC IRBNCE
[ 1.157128] pci 0000:00:1c.7: Intel PCH root port ACS workaround enabled
[ 1.164748] pci 0000:00:1c.7: System wakeup disabled by ACPI
[ 1.171447] pci 0000:00:1e.0: System wakeup disabled by ACPI
[ 1.178612] acpiphp: Slot [8] registered
[ 1.183095] pci 0000:00:02.0: PCI bridge to [bus 01]
[ 1.188867] acpiphp: Slot [2] registered
With this patch applied, the system panics in both cases with a proper
panic message.
Signed-off-by: Jiang Liu <jiang.liu@linux.intel.com>
Cc: Tony Luck <tony.luck@intel.com>
Cc: iommu@lists.linux-foundation.org
Cc: H. Peter Anvin <hpa@linux.intel.com>
Cc: Joerg Roedel <joro@8bytes.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Yinghai Lu <yinghai@kernel.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: David Rientjes <rientjes@google.com>
Cc: HATAYAMA Daisuke <d.hatayama@jp.fujitsu.com>
Cc: Jan Beulich <JBeulich@suse.com>
Cc: Richard Weinberger <richard@nod.at>
Cc: Oren Twaig <oren@scalemp.com>
Link: http://lkml.kernel.org/r/1420615903-28253-5-git-send-email-jiang.liu@linux.intel.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
If x2apic got disabled on the kernel command line, then the following
issue can happen:
enable_IR_x2apic()
....
x2apic_mode = 1;
enable_x2apic();
if (x2apic_disabled) {
__disable_x2apic();
return;
}
That leaves X2APIC disabled in hardware, but x2apic_mode stays 1. So
all other code which checks x2apic_mode gets the wrong information.
Set x2apic_mode to 0 after disabling it in hardware.
This is just a hotfix. The proper solution is to rework this code so
it has seperate functions for the initial setup on the boot processor
and the secondary cpus, but that's beyond the scope of this fix.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Jiang Liu <jiang.liu@linux.intel.com>
Cc: Tony Luck <tony.luck@intel.com>
Cc: iommu@lists.linux-foundation.org
Cc: H. Peter Anvin <hpa@linux.intel.com>
Cc: Joerg Roedel <joro@8bytes.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Yinghai Lu <yinghai@kernel.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: David Rientjes <rientjes@google.com>
Cc: HATAYAMA Daisuke <d.hatayama@jp.fujitsu.com>
Cc: Jan Beulich <JBeulich@suse.com>
Cc: Richard Weinberger <richard@nod.at>
Cc: Oren Twaig <oren@scalemp.com>
The whole iommu setup for irq remapping is a convoluted mess. The
iommu detect function gets called from mem_init() and the prepare
callback gets called from enable_IR_x2apic() for unknown reasons.
Of course AMD and Intel setup differs in nonsensical ways. Intels
prepare callback is explicit while AMDs prepare callback is implicit
in setup_irq_remapping_ops() just to be called in the prepare call
again.
Because all of this gets called from enable_IR_x2apic() and the dmar
prepare function merily parses the ACPI tables, but does not allocate
memory we end up with memory allocation from irq disabled context
later on.
AMDs iommu code at least allocates the required memory from the
prepare function. That has issues as well, but thats not scope of this
patch.
The goal of this change is to distangle the allocation from the actual
enablement. There is no point to allocate memory from irq disabled
regions with GFP_ATOMIC just because it does not matter at that point
in the boot stage. It matters with physical hotplug later on.
There is another issue with the current setup. Due to the conversion
to stacked irqdomains we end up with a call into the irqdomain
allocation code from irq disabled context, but that code does
GFP_KERNEL allocations rightfully as there is no reason to do
preperatory allocations with GFP_ATOMIC.
That change caused the allocator code to complain about GFP_KERNEL
allocations invoked in atomic context. Boris provided a temporary
hackaround which changed the GFP flags if irq_domain_add() got called
from atomic context. Not pretty and we really dont want to get this
into a mainline release for obvious reasons.
Move the ACPI table parsing and the resulting memory allocations from
the enable to the prepare function. That allows to get rid of the
horrible hackaround in irq_domain_add() later.
[Jiang] Rebased onto v3.19
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Borislav Petkov <bp@alien8.de>
Acked-and-tested-by: Joerg Roedel <joro@8bytes.org>
Cc: Tony Luck <tony.luck@intel.com>
Cc: iommu@lists.linux-foundation.org
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Yinghai Lu <yinghai@kernel.org>
Cc: x86@kernel.org
Link: http://lkml.kernel.org/r/20141205084147.313026156@linutronix.de
Link: http://lkml.kernel.org/r/1420615903-28253-3-git-send-email-jiang.liu@linux.intel.com
Signed-off-by: Jiang Liu <jiang.liu@linux.intel.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
enable_IR_x2apic() calls setup_irq_remapping_ops() which by default
installs the intel dmar remapping ops and then calls the amd iommu irq
remapping prepare callback to figure out whether we are running on an
AMD machine with irq remapping hardware.
Right after that it calls irq_remapping_prepare() which pointlessly
checks:
if (!remap_ops || !remap_ops->prepare)
return -ENODEV;
and then calls
remap_ops->prepare()
which is silly in the AMD case as it got called from
setup_irq_remapping_ops() already a few microseconds ago.
Simplify this and just collapse everything into
irq_remapping_prepare().
The irq_remapping_prepare() remains still silly as it assigns blindly
the intel ops, but that's not scope of this patch.
The scope here is to move the preperatory work, i.e. memory
allocations out of the atomic section which is required to enable irq
remapping.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Borislav Petkov <bp@alien8.de>
Acked-and-tested-by: Joerg Roedel <joro@8bytes.org>
Cc: Tony Luck <tony.luck@intel.com>
Cc: iommu@lists.linux-foundation.org
Cc: Joerg Roedel <jroedel@suse.de>
Cc: H. Peter Anvin <hpa@linux.intel.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Yinghai Lu <yinghai@kernel.org>
Cc: David Rientjes <rientjes@google.com>
Cc: HATAYAMA Daisuke <d.hatayama@jp.fujitsu.com>
Cc: Jan Beulich <JBeulich@suse.com>
Cc: Richard Weinberger <richard@nod.at>
Cc: Oren Twaig <oren@scalemp.com>
Cc: x86@kernel.org
Link: http://lkml.kernel.org/r/20141205084147.232633738@linutronix.de
Link: http://lkml.kernel.org/r/1420615903-28253-2-git-send-email-jiang.liu@linux.intel.com
Signed-off-by: Jiang Liu <jiang.liu@linux.intel.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
version.h inclusion is not necessary as detected by versioncheck.
Signed-off-by: Syam Sidhardhan <s.syam@samsung.com>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
The section about debugging scripting languages has nothing to do with
s390 (and the example is even apparently taken from a i586 host instead),
so let's remove this chapter from the file.
Signed-off-by: Thomas Huth <thuth@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
There are a lot of lines that are longer than 80 columns in this file,
rendering it hard to read in a terminal window. This patch fixes most
of these long lines, and while we're at it, also makes some sentences
more readable, e.g. by replacing "&" with "and", adding proper
punctuation, removing superfluous clauses, etc.
Signed-off-by: Thomas Huth <thuth@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
The s390x ABI requires to zero extend parameters before functions
are called.
Signed-off-by: Michael Holzheu <holzheu@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
