Based on Arnds review comments here https://lkml.org/lkml/2014/11/13/161,
update the miphy365 phy driver to access sysconfig register offsets via
syscfg dt property.
This is because the reg property should not be mixing address spaces
like it does currently for miphy365. This change then also aligns us
to how other platforms such as keystone and bcm7445 pass there syscon
offsets via DT.
This patch breaks DT compatibility, but this platform is considered WIP,
and is only used by a few developers who are upstreaming support for it.
This change has been done as a single atomic commit to ensure it is
bisectable.
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Based on Arnds review comments here https://lkml.org/lkml/2014/11/13/161,
update the phy driver to not use the reg property to access the sysconfig
register offsets.
This is because other phy's (miphy28, miphy365) have a combination of
memory mapped registers and sysconfig control regs, and we shouldn't
be mixing address spaces in the reg property. In addition we would
ideally like the sysconfig offsets to be passed via DT in a uniform way.
This new method will also allow us to support devices which have sysconfig
registers in different banks more easily and it is also analagous to how
keystone and bcm7745 platforms pass there syscon offsets in DT.
This breaks DT compatibility, but this platform is considered WIP, and
is only used by a few developers who are upstreaming support for it.
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
All the use cases in this driver has a regulator_haptic_toggle() call after
regulator_haptic_set_voltage(). So make regulator_haptic_set_voltage() call
regulator_haptic_toggle() to simplify the code.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
This adds a pin-control driver for Zynq.
Changes since v2:
- driver-specific DT properties are passed to the core in two arrays,
one for the actual DT parsing one for the debugfs representation.
Issue a compiler warning when the number of entries is not the same
for both arrays.
Changes since v1:
- fix EMIO_SD1_CD pin name
- add USB to pinmux options
changes since RFCv2:
- let Zynq select PINCTRL_ZYNQ. Boot hangs when pinctrl information is
present in DT but no driver available.
- add #defines to get rid of magical constants
- add commas at end of initializers
- separate changes in mach-zynq in separate patch
- add driver specific io-standard DT property
- refactored pinconf set function to not require arguments for
argument-less properties
- squash other patches in
- support for IO-standard property
- support for low-power mode property
- migration to pinconf_generic_dt_node_to_map_all()
- use newly created infrastructure to add pass driver-specific DT
params to pinconf-generic
changes since RFC:
- use syscon/regmap to access registers in SLCR space
- rebase to 3.18: rename enable -> set_mux
- add kernel-doc
- support pinconf
- supported attributes
- pin-bias: pull up, tristate, disable
- slew-rate: 0 == slow, 1 == fast; generic pinconf does not display
argument
Signed-off-by: Soren Brinkmann <soren.brinkmann@xilinx.com>
Tested-by: Andreas Färber <afaerber@suse.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add documentation for the devicetree binding for the Zynq pincontroller.
Changes since v1:
- fix typo
- add USB related documentation
- remove 'pinctrl-' prefix for pinctrl sub-nodes
- update documentation to enforce strict separation of pinmux
and pinconf nodes
- update example accordingly
Signed-off-by: Soren Brinkmann <soren.brinkmann@xilinx.com>
Tested-by: Andreas Färber <afaerber@suse.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Additionally to the generic DT parameters, allow drivers to provide
driver-specific DT parameters to be used with the generic parser
infrastructure.
To achieve this 'struct pinctrl_desc' is extended to pass custom pinconf
option to the core. In order to pass this kind of information, the
related data structures - 'struct pinconf_generic_dt_params',
'pin_config_item' - are moved from pinconf internals to the
pinconf-generic header.
Additionally pinconfg-generic is refactored to not only iterate over the
generic pinconf parameters but also take the parameters into account
that are provided through the driver's 'struct pinctrl_desc'.
In particular 'pinconf_generic_parse_dt_config()' and
'pinconf_generic_dump' helpers are split into two parts each. In order
to have a more generic helper that can be used to process the generic
parameters as well as the driver-specific ones.
v2:
- fix typo
- add missing documentation for @conf_items member in struct
- rebase to pinctrl/devel: conflict in abx500
- rename _pinconf_generic_dump() to pinconf_generic_dump_one()
- removed '_' from _parse_dt_cfg()
- removed BUG_ONs, error condition is handled in if statements
- removed pinconf_generic_dump_group() & pinconf_generic_dump_pin
helpers
- fixed up corresponding call sites
- renamed pinconf_generic_dump() to pinconf_generic_dump_pins()
- added kernel-doc to pinconf_generic_dump_pins()
- add kernel-doc
- more verbose commit message
Signed-off-by: Soren Brinkmann <soren.brinkmann@xilinx.com>
Tested-by: Andreas Färber <afaerber@suse.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
With the new 'groups' property, the DT parser can infer the map type
from the fact whether 'pins' or 'groups' is used to specify the pin
group to work on.
To maintain backwards compatibitliy with current usage of the DT
binding, this is only done when PIN_MAP_TYPE_INVALID is passed to the
parsing function as type.
Also, a new helper 'pinconf_generic_dt_node_to_map_all()' is introduced,
which can be used by drivers as generic callback for dt_node_to_map() to
leverage the new feature.
Changes since v2:
- rename dt_pin_specifier to subnode_target_type
- add additional comment in header file explaining passing an invalid
map type
- mention map_all() helper in commit message
Changes since RFC v2:
- none
Signed-off-by: Soren Brinkmann <soren.brinkmann@xilinx.com>
Tested-by: Andreas Färber <afaerber@suse.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Pull ARM fixes from Russell King:
"Three small fixes from over the Christmas period, and wiring up the
new execveat syscall for ARM"
* 'fixes' of git://ftp.arm.linux.org.uk/~rmk/linux-arm:
ARM: 8275/1: mm: fix PMD_SECT_RDONLY undeclared compile error
ARM: 8253/1: mm: use phys_addr_t type in map_lowmem() for kernel mem region
ARM: 8249/1: mm: dump: don't skip regions
ARM: wire up execveat syscall
Pull x86 fixes from Ingo Molnar:
"Misc fixes: two vdso fixes, two kbuild fixes and a boot failure fix
with certain odd memory mappings"
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86, vdso: Use asm volatile in __getcpu
x86/build: Clean auto-generated processor feature files
x86: Fix mkcapflags.sh bash-ism
x86: Fix step size adjustment during initial memory mapping
x86_64, vdso: Fix the vdso address randomization algorithm
Pull scheduler fixes from Ingo Molnar:
"Misc fixes: group scheduling corner case fix, two deadline scheduler
fixes, effective_load() overflow fix, nested sleep fix, 6144 CPUs
system fix"
* 'sched-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
sched/fair: Fix RCU stall upon -ENOMEM in sched_create_group()
sched/deadline: Avoid double-accounting in case of missed deadlines
sched/deadline: Fix migration of SCHED_DEADLINE tasks
sched: Fix odd values in effective_load() calculations
sched, fanotify: Deal with nested sleeps
sched: Fix KMALLOC_MAX_SIZE overflow during cpumask allocation
Pull perf fixes from Ingo Molnar:
"Mostly tooling fixes, but also some kernel side fixes: uncore PMU
driver fix, user regs sampling fix and an instruction decoder fix that
unbreaks PEBS precise sampling"
* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
perf/x86/uncore/hsw-ep: Handle systems with only two SBOXes
perf/x86_64: Improve user regs sampling
perf: Move task_pt_regs sampling into arch code
x86: Fix off-by-one in instruction decoder
perf hists browser: Fix segfault when showing callchain
perf callchain: Free callchains when hist entries are deleted
perf hists: Fix children sort key behavior
perf diff: Fix to sort by baseline field by default
perf list: Fix --raw-dump option
perf probe: Fix crash in dwarf_getcfi_elf
perf probe: Fix to fall back to find probe point in symbols
perf callchain: Append callchains only when requested
perf ui/tui: Print backtrace symbols when segfault occurs
perf report: Show progress bar for output resorting
Pull locking fixes from Ingo Molnar:
"A liblockdep fix and a mutex_unlock() mutex-debugging fix"
* 'locking-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
mutex: Always clear owner field upon mutex_unlock()
tools/liblockdep: Fix debug_check thinko in mutex destroy
Fix for BUG_ON(anon_vma->degree) splashes in unlink_anon_vmas() ("kernel
BUG at mm/rmap.c:399!") caused by commit 7a3ef208e6 ("mm: prevent
endless growth of anon_vma hierarchy")
Anon_vma_clone() is usually called for a copy of source vma in
destination argument. If source vma has anon_vma it should be already
in dst->anon_vma. NULL in dst->anon_vma is used as a sign that it's
called from anon_vma_fork(). In this case anon_vma_clone() finds
anon_vma for reusing.
Vma_adjust() calls it differently and this breaks anon_vma reusing
logic: anon_vma_clone() links vma to old anon_vma and updates degree
counters but vma_adjust() overrides vma->anon_vma right after that. As
a result final unlink_anon_vmas() decrements degree for wrong anon_vma.
This patch assigns ->anon_vma before calling anon_vma_clone().
Signed-off-by: Konstantin Khlebnikov <koct9i@gmail.com>
Reported-and-tested-by: Chris Clayton <chris2553@googlemail.com>
Reported-and-tested-by: Oded Gabbay <oded.gabbay@amd.com>
Reported-and-tested-by: Chih-Wei Huang <cwhuang@android-x86.org>
Acked-by: Rik van Riel <riel@redhat.com>
Acked-by: Vlastimil Babka <vbabka@suse.cz>
Cc: Daniel Forrest <dan.forrest@ssec.wisc.edu>
Cc: Michal Hocko <mhocko@suse.cz>
Cc: stable@vger.kernel.org # to match back-porting of 7a3ef208e6
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Commit fee7e49d45 ("mm: propagate error from stack expansion even for
guard page") made sure that we return the error properly for stack
growth conditions. It also theorized that counting the guard page
towards the stack limit might break something, but also said "Let's see
if anybody notices".
Somebody did notice. Apparently android-x86 sets the stack limit very
close to the limit indeed, and including the guard page in the rlimit
check causes the android 'zygote' process problems.
So this adds the (fairly trivial) code to make the stack rlimit check be
against the actual real stack size, rather than the size of the vma that
includes the guard page.
Reported-and-tested-by: Chih-Wei Huang <cwhuang@android-x86.org>
Cc: Jay Foad <jay.foad@gmail.com>
Cc: stable@kernel.org # to match back-porting of fee7e49d45
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Remove the function ata_do_simple_cmd() that is not used anywhere.
This was partially found by using a static code analysis program called cppcheck.
Signed-off-by: Rickard Strandqvist <rickard_strandqvist@spectrumdigital.se>
Signed-off-by: Tejun Heo <tj@kernel.org>
Removes some functions that are not used anywhere:
snd_wm8766_set_power() snd_wm8766_set_master_mode()
This was partially found by using a static code analysis program called cppcheck.
Signed-off-by: Rickard Strandqvist <rickard_strandqvist@spectrumdigital.se>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
MARCO will not be supported any more. it has been replaced by CSR
atlas7.
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Since the advent of VGIC dynamic initialization, this latter is
initialized quite late on the first vcpu run or "on-demand", when
injecting an IRQ or when the guest sets its registers.
This initialization could be initiated explicitly much earlier
by the users-space, as soon as it has provided the requested
dimensioning parameters.
This patch adds a new entry to the VGIC KVM device that allows
the user to manually request the VGIC init:
- a new KVM_DEV_ARM_VGIC_GRP_CTRL group is introduced.
- Its first attribute is KVM_DEV_ARM_VGIC_CTRL_INIT
The rationale behind introducing a group is to be able to add other
controls later on, if needed.
Signed-off-by: Eric Auger <eric.auger@linaro.org>
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>
To be more explicit on vgic initialization failure, -ENODEV is
returned by vgic_init when no online vcpus can be found at init.
Signed-off-by: Eric Auger <eric.auger@linaro.org>
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>
Designing Cards and Drivers for the Macintosh Family, 3rd ed. on page 310
says that the I/O address space for the Mac LC is $50F0 0000 - $50FF FFFF.
The developer notes for the Classic II, LC III and IIvx/IIvi give the same
I/O address space.
That means I've assigned the wrong platform resources to those Mac models.
Fix the scsi_type initialization for the affected models, to restore the
SCSI base address to its value prior to Linux 3.18.
Also rename MAC_SCSI_CCL as MAC_SCSI_LC for the sake of correct chronology.
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
As of commit 00f634bc52 ("asm-generic: add generic futex for
!CONFIG_SMP") asm-generic follows the m68k futex implementation.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Remove the function mvme147_init_console_port() that is not used
anywhere.
This was partially found by using a static code analysis program called
cppcheck.
Signed-off-by: Rickard Strandqvist <rickard_strandqvist@spectrumdigital.se>
[geert: Also remove now unused m147_scc_write(), scc_write(), scc_delay()]
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Remove some functions that are not used anywhere:
atari_kbd_leds() ikbd_exec() ikbd_mem_read() ikbd_mem_write()
ikbd_clock_get() ikbd_clock_set() ikbd_pause() ikbd_resume()
This was partially found by using a static code analysis program called
cppcheck.
Signed-off-by: Rickard Strandqvist <rickard_strandqvist@spectrumdigital.se>
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
The rtc.o is built for obj-y, i.e. always built in. It will
never be modular, so using module_init as an alias for __initcall
can be somewhat misleading.
Fix this up now, so that we can relocate module_init from
init.h into module.h in the future. If we don't do this, we'd
have to add module.h to obviously non-modular code, and that
would be a worse thing.
Note that direct use of __initcall is discouraged, vs. one
of the priority categorized subgroups. As __initcall gets
mapped onto device_initcall, our use of device_initcall
directly in this change means that the runtime impact is
zero -- it will remain at level 6 in initcall ordering.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
The FSF address is subject to change. So, we remove it from the header.
While here, remove a line with my old and non-functional email from the
header. Moreover, nowadays we have a Git VCS that contains a history of
changes.
Signed-off-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Input_unregister_device will internally free the device, so
input_free_device should not be called.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
A system misconfiguration that prevents qemu from running at all (for
example, a missing dynamically linked library) will keep the console.log
file from the previous run. This can fool the developer into thinking
that this failed run actually completed correctly. This commit therefore
overwrites the console.log file just before launching qemu.
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
More recent qemu implementations really want "-enable-kvm", and the
"-soundhw pcspk" makes the script a bit less dependent on odd audio
libraries being installed. This commit therefore adds both to the
default qemu command line.
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
The mpstat command recently added the %gnice column, which messes up
the cpu2use.sh script's idle-CPU calculations. This commit therefore
uses $NF instead of $12 to select the last (%idle) column.
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Currently, rcutorture's Reader Batch checks measure from the end of
the previous grace period to the end of the current one. This commit
tightens up these checks by measuring from the start and end of the same
grace period. This involves adding rcu_batches_started() and friends
corresponding to the existing rcu_batches_completed() and friends.
We leave SRCU alone for the moment, as it does not yet have a way of
tracking both ends of its grace periods.
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Now that the return type of rcu_batches_completed() and friends matches
that of the rcu_torture_ops structure's ->completed field, the wrapper
functions can be deleted. This commit carries out that deletion, while
also wiring "sched"'s ->completed field to rcu_batches_completed_sched().
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
A bug in rcutorture has caused it to ignore completed batches.
In preparation for fixing that bug, this commit provides TINY_RCU with
the required rcu_batches_completed_sched().
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
The counter returned by the various ->completed functions is subject to
overflow, which means that subtracting two such counters might result
in overflow, which invokes undefined behavior in the C standard. This
commit therefore changes these functions and variables to unsigned to
avoid this undefined behavior.
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Long ago, the various ->completed fields were of type long, but now are
unsigned long due to signed-integer-overflow concerns. However, the
various _batches_completed() functions remained of type long, even though
their only purpose in life is to return the corresponding ->completed
field. This patch cleans this up by changing these functions' return
types to unsigned long.
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Normal rcutorture checking overestimates grace periods somewhat due to
the fact that there is a delay from a grace-period request until the
start of the corresponding grace period and another delay from the end
of that grace period to notification of the requestor. This means that
rcutorture's detection of RCU bugs is less sensitive than it might be.
It turns out that rcutorture also checks the underlying grace-period
"completed" counter (displayed in Reader Batch output), which in theory
allows rcutorture to do exact checks. In practice, memory misordering
(by both compiler and CPU) can result in false positives. However,
experience on x86 shows that these false positives are quite rare,
occurring less than one time per 1,000 hours of testing. This commit
therefore does the exact checking, giving a warning if any Reader Batch
blows happen, and flagging an error if they happen more often than
once every three hours in long tests.
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
dmesg (from util-linux) currently has two methods for reading the kernel
message ring buffer: /dev/kmsg and syslog(2). Since kernel 3.5.0 kmsg
has been the default, which escapes control characters (e.g. new lines)
before they are shown.
This change means that when dmesg is using /dev/kmsg, a 2 line printk
makes the output messy, because the second line does not get a
timestamp.
For example:
[ 0.012863] CPU0: Thermal monitoring enabled (TM1)
[ 0.012869] Last level iTLB entries: 4KB 1024, 2MB 1024, 4MB 1024
Last level dTLB entries: 4KB 1024, 2MB 1024, 4MB 1024, 1GB 4
[ 0.012958] Freeing SMP alternatives memory: 28K (ffffffff81d86000 - ffffffff81d8d000)
[ 0.014961] dmar: Host address width 39
Because printk.c intentionally escapes control characters, they should
not be there in the first place. This patch fixes two occurrences of
this.
Signed-off-by: Steven Honeyman <stevenhoneyman@gmail.com>
Link: https://lkml.kernel.org/r/1414856696-8094-1-git-send-email-stevenhoneyman@gmail.com
[ Boris: make cpu_detect_tlb() static, while at it. ]
Signed-off-by: Borislav Petkov <bp@suse.de>
When drivers are compiled in subdirectories the -DDEBUG flag need
to be passed in the individual Makefiles.
Reported-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Suggested-by: Yingjoe Chen <yingjoe.chen@mediatek.com>
Cc: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
After the Nomadik pin controller was force migrated to generic pin
control bindings, some leftovers in the documentation need to be
cleaned up. The code and device trees are already migrated.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
