Commit graph

505,617 commits

Author SHA1 Message Date
Nadav Amit
518547b32a KVM: x86: Emulator does not calculate address correctly
In long-mode, when the address size is 4 bytes, the linear address is not
truncated as the emulator mistakenly does.  Instead, the offset within the
segment (the ea field) should be truncated according to the address size.

As Intel SDM says: "In 64-bit mode, the effective address components are added
and the effective address is truncated ... before adding the full 64-bit
segment base."

Signed-off-by: Nadav Amit <namit@cs.technion.ac.il>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
2014-11-03 12:07:24 +01:00
Nadav Amit
6bdf06625d KVM: x86: DR7.GD should be cleared upon any #DB exception
Intel SDM 17.2.4 (Debug Control Register (DR7)) says: "The processor clears the
GD flag upon entering to the debug exception handler." This sentence may be
misunderstood as if it happens only on #DB due to debug-register protection,
but it happens regardless to the cause of the #DB.

Fix the behavior to match both real hardware and Bochs.

Signed-off-by: Nadav Amit <namit@cs.technion.ac.il>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
2014-11-03 12:07:23 +01:00
Nadav Amit
394457a928 KVM: x86: some apic broadcast modes does not work
KVM does not deliver x2APIC broadcast messages with physical mode.  Intel SDM
(10.12.9 ICR Operation in x2APIC Mode) states: "A destination ID value of
FFFF_FFFFH is used for broadcast of interrupts in both logical destination and
physical destination modes."

In addition, the local-apic enables cluster mode broadcast. As Intel SDM
10.6.2.2 says: "Broadcast to all local APICs is achieved by setting all
destination bits to one." This patch enables cluster mode broadcast.

The fix tries to combine broadcast in different modes through a unified code.

One rare case occurs when the source of IPI has its APIC disabled.  In such
case, the source can still issue IPIs, but since the source is not obliged to
have the same LAPIC mode as the enabled ones, we cannot rely on it.
Since it is a rare case, it is unoptimized and done on the slow-path.

Signed-off-by: Nadav Amit <namit@cs.technion.ac.il>
Reviewed-by: Radim Krčmář <rkrcmar@redhat.com>
Reviewed-by: Wanpeng Li <wanpeng.li@linux.intel.com>
[As per Radim's review, use unsigned int for X2APIC_BROADCAST, return bool from
 kvm_apic_broadcast. - Paolo]
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
2014-11-03 12:07:22 +01:00
Andy Lutomirski
52ce3c21ae x86,kvm,vmx: Don't trap writes to CR4.TSD
CR4.TSD is guest-owned; don't trap writes to it in VMX guests.  This
avoids a VM exit on context switches into or out of a PR_TSC_SIGSEGV
task.

I think that this fixes an unintentional side-effect of:
    4c38609ac5 KVM: VMX: Make guest cr4 mask more conservative

Signed-off-by: Andy Lutomirski <luto@amacapital.net>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
2014-11-03 12:07:22 +01:00
Nadav Amit
bf0b682c9b KVM: x86: Sysexit emulation does not mask RIP/RSP
If the operand size is not 64-bit, then the sysexit instruction should assign
ECX to RSP and EDX to RIP.  The current code assigns the full 64-bits.

Fix it by masking.

Signed-off-by: Nadav Amit <namit@cs.technion.ac.il>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
2014-11-03 12:07:21 +01:00
Nadav Amit
58b7075d05 KVM: x86: Distinguish between stack operation and near branches
In 64-bit, stack operations default to 64-bits, but can be overriden (to
16-bit) using opsize override prefix. In contrast, near-branches are always
64-bit.  This patch distinguish between the different behaviors.

Signed-off-by: Nadav Amit <namit@cs.technion.ac.il>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
2014-11-03 12:07:20 +01:00
Nadav Amit
f7784046ab KVM: x86: Getting rid of grp45 in emulator
Breaking grp45 to the relevant functions to speed up the emulation and simplify
the code. In addition, it is necassary the next patch will distinguish between
far and near branches according to the flags.

Signed-off-by: Nadav Amit <namit@cs.technion.ac.il>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
2014-11-03 12:07:20 +01:00
Nadav Amit
4be4de7ef9 KVM: x86: Use new is_noncanonical_address in _linearize
Replace the current canonical address check with the new function which is
identical.

Signed-off-by: Nadav Amit <namit@cs.technion.ac.il>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
2014-11-03 12:07:19 +01:00
Paolo Bonzini
d09155d2f3 KVM: emulator: always inline __linearize
The two callers have a lot of constant arguments that can be
optimized out.

Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
2014-11-03 12:07:18 +01:00
Paolo Bonzini
123b2dd10b Merge remote-tracking branch 'origin/master' into HEAD
Several important fixes went in between 3.18-rc1 and 3.18-rc3, so
KVM/x86 work for 3.19 will be based on 3.18-rc3.
2014-11-03 12:06:21 +01:00
ほち
30934dd3e8 [media] dvb-frontends/Kconfig: better describe Toshiba TC90522
Toshiba TC90522 is wrongly categorized, fix it

Signed-off-by: ほち, AreMa Inc <knightrider@are.ma>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
2014-11-03 08:58:25 -02:00
Amber Thrall
f3a75505ab [media] Staging: media: lirc: cleaned up packet dump in 2 files
lirc_imon.c and lirc_sasem.c contain an incoming_packet method that
is using deprecated printk's.  Removed blocks replacing with single
dev_info with a %*ph format instead.

Signed-off-by: Amber Thrall <amber.rose.thrall@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
2014-11-03 08:38:17 -02:00
Hans Verkuil
c0d5b5fbbe [media] cx88: fix VBI support
Now works with both NTSC and PAL. Tested with CC/XDS for NTSC and
teletext/WSS for PAL. The start lines were wrong, the WSS signal
wasn't captured and there was no difference between NTSC and PAL
w.r.t. the count[] values so NTSC returned way too many lines.

Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
2014-11-03 08:36:40 -02:00
Hans Verkuil
98822de9ae [media] cx88: pci_disable_device comes after free_irq
Move pci_disable_device() down otherwise it will complain about an
unfreed irq.

Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
2014-11-03 08:35:56 -02:00
Hans Verkuil
c39ba33032 [media] cx88: consistently use UNSET for absent tuner
Don't mix UNSET and TUNER_ABSENT: you have to pick one or the other. For
this driver selecting UNSET to represent an absent tuner resulting in
the fewest changes.

Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
2014-11-03 08:35:34 -02:00
Alexander Stein
2667c6adfc ARM: at91/dt: at91sam9263: Add CAN device nodes
Add the missing CAN devices node including their pin muxing. The required
clock node already exists.

Signed-off-by: Alexander Stein <alexander.stein@systec-electronic.com>
Acked-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
2014-11-03 11:34:33 +01:00
Hans Verkuil
078859a323 [media] cx88: don't allow changes while vb2_is_busy
Make sure that changing the standard or format is not allowed while
one or more of the video, vbi or mpeg vb2 queues are busy.

Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
2014-11-03 08:34:33 -02:00
Alexander Stein
316a88da4c ARM: at91/dt: at91sam9x5: Add CAN device nodes
Add the missing CAN devices node including their pin muxing to the shared
.dtsi for at91sam9x5. Actually include this file.

Signed-off-by: Alexander Stein <alexander.stein@systec-electronic.com>
Acked-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
2014-11-03 11:34:32 +01:00
Nicolas Ferre
5563d34896 ARM: at91/dt/trivial: at91sam9x5_can.dtsi: comment and whitespace fixes
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
2014-11-03 11:34:31 +01:00
Jiri Prchal
dd4f25a3ed ARM: at91: at91sam9x5 dt: add usart dma definitions to dt
This patch adds usart dma definitions to both dtsi for sam9x5 chips. Without
usage of dma it's unable to catch all bytes on usart receiver.

Signed-off-by: Jiri Prchal <jiri.prchal@aksignal.cz>
Acked-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
2014-11-03 11:34:23 +01:00
Hans Verkuil
fb37ab3e78 [media] cx88: drop mpeg_active field
The vb2 framework knows if streaming is in progress, no need to use
a separate field for that.

Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
2014-11-03 08:33:29 -02:00
Hans Verkuil
ccd6f1d488 [media] cx88: move width, height and field to core struct
The width, height and field values are core fields since both vbi, video
and blackbird use the same video input.

Move those fields to the correct struct.

Also fix the field checks in the try_fmt functions: add V4L2_FIELD_SEQ_BT/TB
support and map incorrect field values to a correct field value instead of
returning an error.

Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
2014-11-03 08:32:36 -02:00
Hans Verkuil
d386259f8e [media] cx88: don't pollute the kernel log
There is no reason to dump the sram code to the kernel log when you
stop streaming. Remove those calls to cx88_sram_channel_dump.

Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
2014-11-03 08:31:01 -02:00
Hans Verkuil
b8f884164b [media] cx88: increase API command timeout
The timeout is way too small. Especially complicated command like
CX2341X_ENC_STOP_CAPTURE takes much more time than 10 ms. Increase the
timeout to 1 second, just as ivtv does (the cx88-blackbird has the
same IP core for MPEG compression as ivtv).

This solves a nasty issue where STOP_CAPTURE would timeout and the
mailbox is left in a busy state, making it impossible to start streaming
a second time without reloading the driver first.

Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
2014-11-03 08:30:26 -02:00
Hans Verkuil
5e7045e3fa [media] cx88: remove dependency on btcx-risc
btcx-risc is for the bt8xx driver and other drivers shouldn't depend
on it. There is no benefit to use that module just to do a
pci_zalloc_consistent.

Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
2014-11-03 08:29:51 -02:00
Hans Verkuil
999b3ceb84 [media] cx88: drop cx88_free_buffer
Remove this function. This makes all vb2 queues behave the same, which
simplifies comparing the various vb2 queue op implementations.

Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
2014-11-03 08:28:30 -02:00
Hans Verkuil
eddd326320 [media] cx88: return proper errors during fw load
Don't return -1, return a proper error.

Replace dprintk(0, ...) by pr_err since firmware load errors should just be
reported as an error.

Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
2014-11-03 08:27:36 -02:00
Hans Verkuil
c79a23f33d [media] cx88: fix sparse warning
drivers/media/pci/cx88/cx88-blackbird.c:476:25: warning: cast to restricted __le32

Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
2014-11-03 08:26:59 -02:00
Hans Verkuil
0b6b6302d9 [media] cx88: convert to vb2
As usual, this patch is very large due to the fact that half a vb2 conversion
isn't possible. And since this affects blackbird, alsa, core, dvb, vbi and
video the changes are all over.

What made this more difficult was the peculiar way the risc program was setup.
The driver allowed for running out of buffers in which case the DMA would stop
and restart when the next buffer was queued. There was also a complicated
timeout system for when buffers weren't filled. This was replaced by a much
simpler scheme where there is always one buffer around and the DMA will just
cycle that buffer until a new buffer is queued. In that case the previous
buffer will be chained to the new buffer. An interrupt is generated at the
start of the new buffer telling the driver that the previous buffer can be
passed on to userspace.

Much simpler and more robust.

Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
2014-11-03 08:26:33 -02:00
Hans Verkuil
b2c75abde0 [media] cx88: drop videobuf abuse in cx88-alsa
The alsa driver uses videobuf low-level functions that are not
available in vb2, so replace them by driver-specific functions.

Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
2014-11-03 08:21:55 -02:00
Hans Verkuil
6f11adc6a5 [media] cx88: drop the bogus 'queue' list in dmaqueue
This list is only used if the width, height and/or format of a buffer has
changed, but that can never happen. Remove it and all associated code.

Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
2014-11-03 08:21:24 -02:00
Hans Verkuil
637bc20796 [media] cx88: remove fmt from the buffer struct
This is a duplicate of dev->fmt and can be removed. As a consequence a
lot of tests that check if the format has changed midstream can be
removed as well: the format cannot change midstream, so this is a bogus
check.

Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
2014-11-03 08:20:45 -02:00
Jesse Brandeburg
a282babcfd i40e: avoid disable of interrupt when changing ITR
The call to irq_dynamic_disable was turning off the interrupt completely
when trying to set ITR to 0 (for lowest moderation).  Just remove the
call as setting the values to 0 later in this function will suffice.

Change-ID: I47caf1ecbe65653cf63ec833db93094cd83fd84d
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Patrick Lu <patrick.lu@intel.com>
Tested-By: Jim Young <jamesx.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2014-11-03 02:13:57 -08:00
Russell King
06e944b8e5 generic fixmaps
ARM support for CONFIG_DEBUG_RODATA
 -----BEGIN PGP SIGNATURE-----
 Version: GnuPG v1
 Comment: Kees Cook <kees@outflux.net>
 
 iQIcBAABCgAGBQJUQDtHAAoJEIly9N/cbcAmS/gQAJnkmOBN5WLymkYE02QMcRZM
 l70c131QOGimFWUZpPxsyHdUFwASogxGet6LsGcbB40ayCrQw4tzXBlcFOvbY/dM
 HC+1I3CqRDphU/q2Mm/2bpg2F+VPbwIyxACPtsqW824muTHK47qDs3R9vVYDtfPV
 xupOpqz6qNFxgE5/TpDjsjVeJol/i+ygEQzIxo70m0FnLVv5t/deGjDM6bvfqwdm
 po/+hUlkW8lpyQspuucBCxfGagaCSkd67hyHMvq5zDjz1+6T1XljdA7jc7rSa9bI
 eCWuJgmM51AaA1lr+Eu1raSOduk0x1GU33wf1Y0z+qZ0A6ELTDmiY/SLMK6o8n6T
 4kPmzigRRT9a4B9kTR/mj9IyG+LAKu8Bvppl5CedNp2xEtIEGppnHU3d7bFZIVq3
 gCIL0ZG26D467hgUEgJwdJwnIU2GqirR4XyD3Ml+hjGCq6L5QzZpUWiskgh+EoHw
 dIhbJnGBxB2MkVJW0zE+ajVdiFAeU7P3voR74B73kwC9H+S6Fo10pff9LZbs8BKd
 R5RH5xCPDXgjnkjDbXW8e9Zkr58IrT0ffFcwE1IuDQpTMKKQPIlH5DUlRLQSHau9
 abDZuCZpvAPvGO4korTsu0dAXYJHlilG5Ftd856Hmrs+32eMDX2DV+RT4m7YX2Dt
 7tLXNu6P1yRFnjFdGxtR
 =u3lA
 -----END PGP SIGNATURE-----

Merge tag 'ronx-next' of git://git.kernel.org/pub/scm/linux/kernel/git/kees/linux into devel-stable

generic fixmaps
ARM support for CONFIG_DEBUG_RODATA
2014-11-03 10:12:13 +00:00
Sebastian Ott
f7ceb0dfec KVM: s390: virtio_ccw: remove unused variable
Fix this warning:
drivers/s390/kvm/virtio_ccw.c: In function ‘virtio_ccw_int_handler’:
drivers/s390/kvm/virtio_ccw.c:891:24: warning: unused variable ‘drv’ [-Wunused-variable]
    struct virtio_driver *drv;

Signed-off-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Acked-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
2014-11-03 10:43:00 +01:00
Paul M Stillwell Jr
1ac1e7643c i40evf: Add support for 10G base T parts
Add 10G-Base-T support in i40evf.

Change-ID: I98a1c3138d7d6572fe7903a7c1c4692cae3260d5
Signed-off-by: Paul M Stillwell Jr <paul.m.stillwell.jr@intel.com>
Signed-off-by: Patrick Lu <patrick.lu@intel.com>
Tested-by: Jim Young <jamesx.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2014-11-03 01:38:41 -08:00
Mitch Williams
320684cd53 i40e: fix link checking logic
If the interface is closed, but VFs exist, current code will spam all
the VFs with link messages every second. This is because the link event
code was looking at netif_carrier_ok() without checking to see if the
interface was actually open.

Refactor the logic to only check the carrier state if the interface is
actually open. This allows link changes to be reported correctly without
spamming the VFs.

Change-ID: If136e79bb3820d21ea4e39e332e8a9604efc2b2a
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Signed-off-by: Patrick Lu <patrick.lu@intel.com>
Tested-by: Jim Young <jamesx.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2014-11-03 01:31:21 -08:00
Mitch Williams
7bdd6f7487 i40evf: properly handle multiple AQ messages
When we receive an admin queue message, the msg_size field in the event
struct gets overwritten. Because of this, we need to reinit the field
each time we go through the loop. Without this we may receive truncated
messages due to the firmware thinking we have insufficient buffer size.

Change-ID: I21dcca5114d91365d731169965ce3ffec0e4a190
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Signed-off-by: Patrick Lu <patrick.lu@intel.com>
Tested-by: Jim Young <jamesx.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2014-11-03 01:23:24 -08:00
Akeem G Abodunrin
1790ed0c65 i40e: Add condition to enter fdir flush and reinit
When FD_SB/ATR are not enabled, do not allow flow director flush
and reinit.

Change-ID: Iafe261c1862992981615815551abd1ed9fada0a8
Signed-off-by: Akeem G Abodunrin <akeem.g.abodunrin@intel.com>
Signed-off-by: Patrick Lu <patrick.lu@intel.com>
Tested-by: <jamesx.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2014-11-03 01:15:41 -08:00
Philipp Zabel
1a5f77d395 STi reset controller updates for v3.19.
This tag adds support to STiH407 reset controllers:
   1. st,stih407-powerdown
   2. st,stih407-softreset
   3. st,stih407-picophyreset
 -----BEGIN PGP SIGNATURE-----
 Version: GnuPG v1
 
 iQIcBAABAgAGBQJUU3rHAAoJEMo4jShGhw+JFhQQANFvZotCJQdPV6i60Yca20FJ
 /cqMb97w34NhilGwxHxT1cXoE5JccTvE2XauVFzfcE+EpTILjhzEM5/k4Lw9aZmk
 0PMvGHZgx/8uhZ3UQqShLvP7XsFEiLzm/isHUrgHjDJE+uBCUVt3JWu4W2BtO+qU
 RPz5+oE2HW6D0Wh0LdL0EOW8lcITSA9JH8+0baoVLJCP4lsuDJJe+ktGEiSmAlUM
 Ob3++EvyZM1PGoyiqM2Z/hwShttQPb0X8uU60rFMUwd/s3DXw0L2pXX33nELlCk8
 oT/FSg4iwOwg3SnY1IqfNMVyj6KAHDgMz27ebtukM+1XV6vinkwQ6/v7kq47c5at
 SdYtpGO8y4u+/gKd7fOuCPUR2Xa1p2wG7DqRpvd3Ld16QuSb6alKJvxX5y4xX1/N
 sTjZ8bbeqzEvQqIFUH956/AbfB9JeCVRQAFIbyGSnRcdIMGgcD+KbZ4LMM2ZlMaR
 iNbMzfpZf7EPrRFza51+91AbMJmwS50t38YosTI3axtuwLSqfjB/R/57MY+guies
 krwmfBFOY/E0elMwXBxQypOHlpuTQINO8lImkky3AVQOExA5NVGn0ikQrIjZ39Ch
 oTK4BYdgvqIlorlfDrPDZGOK+uZnWkfN55P19W0yfLjlLjva9g57A/Qeeg1hfisI
 OqgXf6Y1TLCNCWG7iuTJ
 =aZN5
 -----END PGP SIGNATURE-----

Merge tag 'sti-reset-for-v3.19-1' of git://git.stlinux.com/devel/kernel/linux-sti into reset/for_v3.19

STi reset controller updates for v3.19.

This tag adds support to STiH407 reset controllers:
  1. st,stih407-powerdown
  2. st,stih407-softreset
  3. st,stih407-picophyreset
2014-11-03 09:50:27 +01:00
Johan Hovold
9d38019038 USB: mos7840: replace unnecessary atomic allocations
Use GFP_KERNEL instead of GFP_ATOMIC for allocations in set_termios and
port-setting helper which both may and do sleep.

Signed-off-by: Johan Hovold <johan@kernel.org>
2014-11-03 09:15:18 +01:00
Johan Hovold
1dbd11be69 USB: mos7720: replace unnecessary atomic allocations
Use GFP_KERNEL instead of GFP_ATOMIC for allocations in set_termios and
port-setting helper which both may and do sleep.

Signed-off-by: Johan Hovold <johan@kernel.org>
2014-11-03 09:15:17 +01:00
Johan Hovold
811c370780 USB: kobil_sct: replace unnecessary atomic allocation
Use GFP_KERNEL instead of GFP_ATOMIC for allocation in open(), which may
sleep.

Signed-off-by: Johan Hovold <johan@kernel.org>
2014-11-03 09:15:15 +01:00
Marcel Holtmann
845472e8d5 Bluetooth: Add hci_conn_lookup_type() helper function
Some drivers require knowledge of what connection handle is assigned
to what connection link type (ACL or SCO/eSCO). Instead of having each
driver implement connection tracking, provide a simple helper function
for lookup of the link type.

Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
2014-11-03 10:13:43 +02:00
Marcel Holtmann
2cbd3f5ccd Bluetooth: btusb: Add internal callback for USB bulk rx data
Some vendors require special handling of the rx data from the USB
bulk endpoints. For that case provide an internal callback that
can overwrite it with a custom receive function.

Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
2014-11-03 10:13:42 +02:00
Marcel Holtmann
40f4938aa6 Bluetooth: Consolidate whitelist debugfs entry into device_list
The debufs entry for the BR/EDR whitelist is confusing since there is
a controller debugfs entry with the name white_list and both are two
different things.

With the BR/EDR whitelist, the actual interface in use is the device
list and thus just include all values from the internal BR/EDR whitelist
in the device_list debugfs entry.

Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
2014-11-03 10:13:42 +02:00
Marcel Holtmann
27c3fbe00b Bluetooth: Set HCI_QUIRK_STRICT_DUPLICATE_FILTER for Broadcom devices
The Bluetooth controllers from Broadcom use a strict scanning filter
policy that filters based on Bluetooth device addresses and not on
RSSI. So tell the core about this.

Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
2014-11-03 10:13:41 +02:00
Marcel Holtmann
43d6bc46e2 Bluetooth: Introduce HCI_QUIRK_STRICT_DUPLICATE_FILTER
Some vendors decide to use a strict duplicate filter policy that only
filters on Bluetooth device addresses. This means that when the RSSI
changes, these devices are not reported again. During discovery it is
useful to actually get the RSSI updates.

Since this is specific to each controller, add a new quirk setting
that allows drivers to tell the core what kind of filtering policy
the controller uses.

Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
2014-11-03 10:13:36 +02:00
Johan Hovold
e681286de2 USB: opticon: fix non-atomic allocation in write path
Write may be called from interrupt context so make sure to use
GFP_ATOMIC for all allocations in write.

Fixes: 0d930e51cf ("USB: opticon: Add Opticon OPN2001 write support")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
2014-11-03 09:07:30 +01:00
Johan Hovold
1912528376 USB: kobil_sct: fix non-atomic allocation in write path
Write may be called from interrupt context so make sure to use
GFP_ATOMIC for all allocations in write.

Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
2014-11-03 09:07:28 +01:00