Commit graph

505,617 commits

Author SHA1 Message Date
Felipe Balbi
fed33afce0 usb: dwc3: core: fix order of PM runtime calls
Currently, we disable pm_runtime before all register
accesses are done, this is dangerous and might lead
to abort exceptions due to the driver trying to access
a register which is clocked by a clock which was long
gated.

Fix that by moving pm_runtime_put_sync() and pm_runtime_disable()
as the last thing we do before returning from our ->remove()
method.

Fixes: 72246da (usb: Introduce DesignWare USB3 DRD Driver)
Cc: <stable@vger.kernel.org> # v3.2+
Signed-off-by: Felipe Balbi <balbi@ti.com>
2014-09-03 16:50:44 -05:00
Felipe Balbi
4b143f0f60 ARM: dts: am4372: fix USB regs size
Size should be 64KiB instead of 92KiB.

Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
2014-09-03 14:48:37 -07:00
Nishanth Menon
9316641330 ARM: dts: am437x-gp: switch i2c0 to 100KHz
On the GP EVM, the ambient light sensor is limited to 100KHz on the
I2C bus.

So use 100kHz for I2C on the GP EVM due to this limitation on the
ambient light sensor.

Reported-by: Aparna Balasubramanian <aparnab@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
2014-09-03 14:46:55 -07:00
Benjamin Tissoires
e4cf19ffe0 HID: thingm: set the proper error code before leaving
In case of an unsupported firmware, the driver bails out without setting
the LEDs interfaces, but forget to set the proper error code.
err is then still equal to 0 and the hid subsytem consider the device
to be in perfect shape.
When removing it, thingm_remove() tries to unbind the rgb LEDs which
has not been created, leading to a segfault.

Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
2014-09-03 23:46:09 +02:00
Mauro Carvalho Chehab
c56019fc40 [media] tuner-xc2028: fix bad alignments
As reported by cocinelle:

drivers/media/tuners/tuner-xc2028.c:182:2-18: code aligned with following code on line 183
drivers/media/tuners/tuner-xc2028.c:184:2-19: code aligned with following code on line 185
drivers/media/tuners/tuner-xc2028.c:186:2-19: code aligned with following code on line 187
drivers/media/tuners/tuner-xc2028.c:188:2-17: code aligned with following code on line 189
drivers/media/tuners/tuner-xc2028.c:190:2-19: code aligned with following code on line 191
drivers/media/tuners/tuner-xc2028.c:192:2-19: code aligned with following code on line 193
drivers/media/tuners/tuner-xc2028.c:194:2-18: code aligned with following code on line 195
drivers/media/tuners/tuner-xc2028.c:196:2-17: code aligned with following code on line 197
drivers/media/tuners/tuner-xc2028.c:198:2-18: code aligned with following code on line 199
drivers/media/tuners/tuner-xc2028.c:200:2-19: code aligned with following code on line 201
drivers/media/tuners/tuner-xc2028.c:202:2-18: code aligned with following code on line 203
drivers/media/tuners/tuner-xc2028.c:204:2-16: code aligned with following code on line 205
drivers/media/tuners/tuner-xc2028.c:206:2-20: code aligned with following code on line 207
drivers/media/tuners/tuner-xc2028.c:208:2-17: code aligned with following code on line 209
drivers/media/tuners/tuner-xc2028.c:210:2-18: code aligned with following code on line 211
drivers/media/tuners/tuner-xc2028.c:212:2-18: code aligned with following code on line 213
drivers/media/tuners/tuner-xc2028.c:214:2-18: code aligned with following code on line 215
drivers/media/tuners/tuner-xc2028.c:216:2-16: code aligned with following code on line 217
drivers/media/tuners/tuner-xc2028.c:218:2-18: code aligned with following code on line 219
drivers/media/tuners/tuner-xc2028.c:220:2-20: code aligned with following code on line 221
drivers/media/tuners/tuner-xc2028.c:222:2-21: code aligned with following code on line 223
drivers/media/tuners/tuner-xc2028.c:224:2-20: code aligned with following code on line 225
drivers/media/tuners/tuner-xc2028.c:226:2-23: code aligned with following code on line 227
drivers/media/tuners/tuner-xc2028.c:228:2-23: code aligned with following code on line 229
drivers/media/tuners/tuner-xc2028.c:230:2-22: code aligned with following code on line 231
drivers/media/tuners/tuner-xc2028.c:232:2-24: code aligned with following code on line 233
drivers/media/tuners/tuner-xc2028.c:234:2-19: code aligned with following code on line 235
drivers/media/tuners/tuner-xc2028.c:236:2-19: code aligned with following code on line 237
drivers/media/tuners/tuner-xc2028.c:238:2-20: code aligned with following code on line 239
drivers/media/tuners/tuner-xc2028.c:240:2-19: code aligned with following code on line 241

Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
2014-09-03 18:44:34 -03:00
Nishanth Menon
9a15fff05b ARM: dts: am335x-bone*: Fix model name and update compatibility information
Beaglebone white and beaglebone black differ in tiny little aspects.
This is the reason why we maintain seperate dts for these platforms.
However, there is no real way to decode from dtb which platform it is
since compatible and model name are the same for both platforms.

Fix this so that beaglebone black and beaglebone are identifiable,
while maintaining compatibility for older zImages which might use old
beaglebone compatible flag for black as well.

Reported-by: Tom Rini <trini@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
2014-09-03 14:44:12 -07:00
Kinglong Mee
027bc41a3e NFSD: Put export if prepare_creds() fail
Signed-off-by: Kinglong Mee <kinglongmee@gmail.com>
Signed-off-by: J. Bruce Fields <bfields@redhat.com>
2014-09-03 17:43:04 -04:00
Kinglong Mee
13c82e8eb5 NFSD: Full checking of authentication name
Signed-off-by: Kinglong Mee <kinglongmee@gmail.com>
Signed-off-by: J. Bruce Fields <bfields@redhat.com>
2014-09-03 17:43:03 -04:00
Kinglong Mee
48c348b09c NFSD: Fix bad using of return value from qword_get
Signed-off-by: Kinglong Mee <kinglongmee@gmail.com>
Signed-off-by: J. Bruce Fields <bfields@redhat.com>
2014-09-03 17:43:02 -04:00
Kinglong Mee
15d176c195 NFSD: Fix a memory leak if nfsd4_recdir_load fail
Signed-off-by: Kinglong Mee <kinglongmee@gmail.com>
Signed-off-by: J. Bruce Fields <bfields@redhat.com>
2014-09-03 17:43:01 -04:00
Kinglong Mee
c2236f141e NFSD: Reset creds after mnt_want_write_file() fail
Signed-off-by: Kinglong Mee <kinglongmee@gmail.com>
Signed-off-by: J. Bruce Fields <bfields@redhat.com>
2014-09-03 17:43:01 -04:00
Kinglong Mee
8519f994e5 NFSD: Put file after ima_file_check fail in nfsd_open()
Signed-off-by: Kinglong Mee <kinglongmee@gmail.com>
Signed-off-by: J. Bruce Fields <bfields@redhat.com>
2014-09-03 17:43:00 -04:00
Benjamin Tissoires
89f2ab55ea HID: wacom: Add support for the Cintiq Companion
The Wacom Cintiq Companion shares the same sensor than the Cintiq
Companion Hybrid, with the exception of the different PIDs.

Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
2014-09-03 23:42:53 +02:00
Mauro Carvalho Chehab
97e0e1e867 [media] xc4000: Fix bad alignments
As reported by cocinelle:

drivers/media/tuners/xc4000.c:573:2-28: code aligned with following code on line 574
drivers/media/tuners/xc4000.c:575:2-29: code aligned with following code on line 576
drivers/media/tuners/xc4000.c:577:2-29: code aligned with following code on line 578
drivers/media/tuners/xc4000.c:579:2-27: code aligned with following code on line 580
drivers/media/tuners/xc4000.c:581:2-29: code aligned with following code on line 582
drivers/media/tuners/xc4000.c:583:2-29: code aligned with following code on line 584
drivers/media/tuners/xc4000.c:585:2-28: code aligned with following code on line 586
drivers/media/tuners/xc4000.c:587:2-27: code aligned with following code on line 588
drivers/media/tuners/xc4000.c:589:2-28: code aligned with following code on line 590
drivers/media/tuners/xc4000.c:591:2-29: code aligned with following code on line 592
drivers/media/tuners/xc4000.c:593:2-28: code aligned with following code on line 594
drivers/media/tuners/xc4000.c:595:2-26: code aligned with following code on line 596
drivers/media/tuners/xc4000.c:597:2-30: code aligned with following code on line 598
drivers/media/tuners/xc4000.c:599:2-27: code aligned with following code on line 600
drivers/media/tuners/xc4000.c:601:2-28: code aligned with following code on line 602
drivers/media/tuners/xc4000.c:603:2-28: code aligned with following code on line 604
drivers/media/tuners/xc4000.c:605:2-28: code aligned with following code on line 606
drivers/media/tuners/xc4000.c:607:2-26: code aligned with following code on line 608
drivers/media/tuners/xc4000.c:609:2-28: code aligned with following code on line 610
drivers/media/tuners/xc4000.c:611:2-30: code aligned with following code on line 612
drivers/media/tuners/xc4000.c:613:2-31: code aligned with following code on line 614
drivers/media/tuners/xc4000.c:615:2-30: code aligned with following code on line 616
drivers/media/tuners/xc4000.c:617:2-33: code aligned with following code on line 618
drivers/media/tuners/xc4000.c:619:2-33: code aligned with following code on line 620
drivers/media/tuners/xc4000.c:621:2-32: code aligned with following code on line 622
drivers/media/tuners/xc4000.c:623:2-34: code aligned with following code on line 624
drivers/media/tuners/xc4000.c:625:2-29: code aligned with following code on line 626
drivers/media/tuners/xc4000.c:627:2-29: code aligned with following code on line 628
drivers/media/tuners/xc4000.c:629:2-30: code aligned with following code on line 630
drivers/media/tuners/xc4000.c:631:2-29: code aligned with following code on line 632

Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
2014-09-03 18:42:09 -03:00
Tony Lindgren
5c01d5d134 Merge branch 'for-v3.17-rc/ti-clk-dt' of github.com:t-kristo/linux-pm into fixes-rc3 2014-09-03 14:39:51 -07:00
Alan Stern
8f507ef522 HID: usbhid: improve handling of Clear-Halt and reset
This patch changes the way usbhid carries out Clear-Halt and reset.

Currently, after a Clear-Halt on the interrupt-IN endpoint, the driver
immediately restarts the interrupt URB, even if the Clear-Halt failed.
This doesn't work out well when the reason for the failure was that
the device was disconnected (when a low- or full-speed device is
connected through a hub to an EHCI controller, transfer errors caused
by disconnection are reported as stalls by the hub).  Instead now the
driver will attempt a reset after a failed Clear-Halt.

The way resets are carried out is also changed.  Now the driver will
call usb_queue_reset_device() instead of calling usb_reset_device()
directly.  This avoids a deadlock that would arise when a device is
unplugged: The hid_reset() routine runs as a workqueue item, a reset
attempt after the device has been unplugged will fail, failure will
cause usbhid to be unbound, and the disconnect routine will try to do
cancel_work_sync().  The usb_queue_reset_device() implementation is
carefully written to handle scenarios like this one properly.

Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
2014-09-03 23:37:38 +02:00
Roger Quadros
f0e9fab3bc ARM: dts: dra7-evm: Fix 8th NAND partition's name
The 8th NAND partition should be named "NAND.u-boot-env.backup1"
instead of "NAND.u-boot-env". This is to be consistent with other
TI boards as well as u-boot.

CC: Pekon Gupta <pekon@pek-sem.com>
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
2014-09-03 14:32:35 -07:00
Roger Quadros
544d63d0f3 ARM: dts: dra7-evm: Fix i2c3 pinmux and frequency
The I2C3 pins are taken from pads E21 (GPIO6_14) and
F20 (GPIO6_15). Use the right pinmux register and mode.

Also set the I2C3 bus frequency to a safer 400KHz than
3.4Mhz.

CC: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
2014-09-03 14:32:00 -07:00
Nishanth Menon
a1a57abaaf ARM: dts: omap4-panda: Fix model and SoC family details
Currently we claim that omap4-panda and omap4-panda-es are essentially
the same, but they are not since PandaBoard-ES uses OMAP4460 and
PandaBoard uses OMAP4430.

So, split the common definition and make the model name available.

Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
2014-09-03 14:23:41 -07:00
Jiri Kosina
6726655dfd ACPI / cpuidle: fix deadlock between cpuidle_lock and cpu_hotplug.lock
There is a following AB-BA dependency between cpu_hotplug.lock and
cpuidle_lock:

1) cpu_hotplug.lock -> cpuidle_lock
enable_nonboot_cpus()
 _cpu_up()
  cpu_hotplug_begin()
   LOCK(cpu_hotplug.lock)
 cpu_notify()
  ...
  acpi_processor_hotplug()
   cpuidle_pause_and_lock()
    LOCK(cpuidle_lock)

2) cpuidle_lock -> cpu_hotplug.lock
acpi_os_execute_deferred() workqueue
 ...
 acpi_processor_cst_has_changed()
  cpuidle_pause_and_lock()
   LOCK(cpuidle_lock)
  get_online_cpus()
   LOCK(cpu_hotplug.lock)

Fix this by reversing the order acpi_processor_cst_has_changed() does
thigs -- let it first execute the protection against CPU hotplug by
calling get_online_cpus() and obtain the cpuidle lock only after that (and
perform the symmentric change when allowing CPUs hotplug again and
dropping cpuidle lock).

Spotted by lockdep.

Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Cc: All applicable <stable@vger.kernel.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
2014-09-03 23:05:55 +02:00
Keith Busch
2da78092dd block: Fix dev_t minor allocation lifetime
Releases the dev_t minor when all references are closed to prevent
another device from acquiring the same major/minor.

Since the partition's release may be invoked from call_rcu's soft-irq
context, the ext_dev_idr's mutex had to be replaced with a spinlock so
as not so sleep.

Signed-off-by: Keith Busch <keith.busch@intel.com>
Cc: stable@kernel.org
Signed-off-by: Jens Axboe <axboe@fb.com>
2014-09-03 15:01:02 -06:00
Mauro Carvalho Chehab
ea21f702fc [media] cx231xx: just return 0 instead of using a var
Instead of allocating a var to store 0 and just return it,
change the code to return 0 directly.

Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
2014-09-03 17:59:57 -03:00
Mauro Carvalho Chehab
2f00fce467 [media] mxl5005s: just return 0 instead of using a var
Instead of allocating a var to store 0 and just return it,
change the code to return 0 directly.

Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
2014-09-03 17:59:56 -03:00
Mauro Carvalho Chehab
4539fc5c68 [media] mt2060: just return 0 instead of using a var
Instead of allocating a var to store 0 and just return it,
change the code to return 0 directly.

Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
2014-09-03 17:59:56 -03:00
Mauro Carvalho Chehab
f2747cf6f0 [media] nuvoton-cir: just return 0 instead of using a var
Instead of allocating a var to store 0 and just return it,
change the code to return 0 directly.

Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
2014-09-03 17:59:55 -03:00
Mauro Carvalho Chehab
fc823729e0 [media] ite-cir: just return 0 instead of using a var
Instead of allocating a var to store 0 and just return it,
change the code to return 0 directly.

Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
2014-09-03 17:59:54 -03:00
Mauro Carvalho Chehab
9b08f41724 [media] fintek-cir: just return 0 instead of using a var
Instead of allocating a var to store 0 and just return it,
change the code to return 0 directly.

Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
2014-09-03 17:59:54 -03:00
Mauro Carvalho Chehab
6cf77d18f6 [media] marvel-ccic: just return 0 instead of using a var
Instead of allocating a var to store 0 and just return it,
change the code to return 0 directly.

Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
2014-09-03 17:59:53 -03:00
Mauro Carvalho Chehab
b80cefb415 [media] davinci: just return 0 instead of using a var
Instead of allocating a var to store 0 and just return it,
change the code to return 0 directly.

Acked-by: "Lad, Prabhakar" <prabhakar.csengg@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
2014-09-03 17:59:30 -03:00
Mauro Carvalho Chehab
5b0eb8271d [media] saa7164: just return 0 instead of using a var
Instead of allocating a var to store 0 and just return it,
change the code to return 0 directly.

Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
2014-09-03 17:59:29 -03:00
Mauro Carvalho Chehab
a896dc7a1f [media] bt8xx: just return 0 instead of using a var
Instead of allocating a var to store 0 and just return it,
change the code to return 0 directly.

Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
2014-09-03 17:59:29 -03:00
Mauro Carvalho Chehab
8b37c6455f [media] media-devnode: just return 0 instead of using a var
Instead of allocating a var to store 0 and just return it,
change the code to return 0 directly.

Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
2014-09-03 17:59:28 -03:00
Mauro Carvalho Chehab
7c9950768f [media] stv0367: just return 0 instead of using a var
Instead of allocating a var to store 0 and just return it,
change the code to return 0 directly.

Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
2014-09-03 17:59:28 -03:00
Mauro Carvalho Chehab
2f1e48d670 [media] siano: just return 0 instead of using a var
Instead of allocating a var to store 0 and just return it,
change the code to return 0 directly.

Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
2014-09-03 17:59:27 -03:00
Mauro Carvalho Chehab
d8e8b40c06 [media] s5p-tv: Simplify the return logic
Make sure pm_runtime_* calls does not use unnecessary
IS_ERR_VALUE().

Reported by scripts/coccinelle/api/pm_runtime.cocci script.

Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
2014-09-03 17:59:27 -03:00
Mauro Carvalho Chehab
a04557a20b [media] e4000: simplify boolean tests
Instead of using if (foo == false), just use
if (!foo).

That allows a faster mental parsing when analyzing the
code.

Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
2014-09-03 17:59:26 -03:00
Mauro Carvalho Chehab
b2617dc3eb [media] via-camera: simplify boolean tests
Instead of using if (foo == false), just use
if (!foo).

That allows a faster mental parsing when analyzing the
code.

Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
2014-09-03 17:59:26 -03:00
Mauro Carvalho Chehab
160ac0babc [media] omap: simplify test logic
instead of testing bools if they are false or true, just use
if (!foo) or if (foo). That makes the code easier to
read and shorter.

Also, properly initialize booleans with true or false.

Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
2014-09-03 17:59:25 -03:00
Mauro Carvalho Chehab
1b21e2187a [media] lm3560: simplify a boolean test
lml33dpatch is boolean. So, the possible values are
true or false.

Instead of using if (lml33dpath), just use
if (!lml33dpath).

That allows a faster mental parsing when analyzing the
code.

Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
2014-09-03 17:59:24 -03:00
Mauro Carvalho Chehab
afb666d1e7 [media] lm3560: simplify boolean tests
Instead of using if (on == true), just use
if (on).

That allows a faster mental parsing when analyzing the
code.

Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
2014-09-03 17:59:24 -03:00
Mauro Carvalho Chehab
5a7f7b79d8 [media] drxk_hard: simplify test logic
instead of testing if it is false or true, just use
if (!foo) or if (foo). That makes the code easier to
read and shorter.

Also, properly initialize booleans with true or false.

Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
2014-09-03 17:59:23 -03:00
Mauro Carvalho Chehab
ad7b8c0227 [media] msi2500: simplify boolean tests
Instead of using if (foo == false), just use
if (!foo).

That allows a faster mental parsing when analyzing the
code.

Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
2014-09-03 17:59:23 -03:00
Mauro Carvalho Chehab
61f6a0569c [media] af9005: use true/false for boolean vars
Instead of using 0 or 1 for boolean, use the true/false
defines.

Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
2014-09-03 17:59:22 -03:00
Mauro Carvalho Chehab
235d89ec4a [media] lmedm04: use true/false for boolean vars
Instead of using 0 or 1 for boolean, use the true/false
defines.

Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
2014-09-03 17:59:22 -03:00
Mauro Carvalho Chehab
f6b83c3e06 [media] au0828-dvb: use true/false for boolean vars
Instead of using 0 or 1 for boolean, use the true/false
defines.

Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
2014-09-03 17:59:21 -03:00
Mauro Carvalho Chehab
2816cc31e0 [media] ene_ir: use true/false for boolean vars
Instead of using 0 or 1 for boolean, use the true/false
defines.

Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
2014-09-03 17:59:20 -03:00
Mauro Carvalho Chehab
8b4b68186f [media] radio: use true/false for boolean vars
Instead of using 0 or 1 for boolean, use the true/false
defines.

Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
2014-09-03 17:59:20 -03:00
Mauro Carvalho Chehab
6c515a44a8 [media] vivid-tpg: use true/false for boolean vars
Instead of using 0 or 1 for boolean, use the true/false
defines.

Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
2014-09-03 17:59:19 -03:00
Mauro Carvalho Chehab
68bbbd7912 [media] ti-vpe: use true/false for boolean vars
Instead of using 0 or 1 for boolean, use the true/false
defines.

Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
2014-09-03 17:59:19 -03:00
Mauro Carvalho Chehab
11b4c175d9 [media] omap3isp: use true/false for boolean vars
Instead of using 0 or 1 for boolean, use the true/false
defines.

Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
2014-09-03 17:59:18 -03:00