Commit graph

505,617 commits

Author SHA1 Message Date
Paolo Bonzini
eebbcf6da9 Merge tag 'kvm-s390-master-20140902' of git://git.kernel.org/pub/scm/linux/kernel/git/kvms390/linux into kvm-master 2014-09-02 11:09:00 +02:00
Will Deacon
4d09d99d54 iommu/arm-smmu: fix corner cases in address size calculations
Working out the usable address sizes for the SMMU is surprisingly tricky.
We must take into account both the limitations of the hardware for VA,
IPA and PA sizes but also any restrictions imposed by the Linux page
table code, particularly when dealing with nested translation (where the
IPA size is limited by the input address size at stage-2).

This patch fixes a few corner cases in our address size handling so that
we correctly deal with 40-bit addresses in TTBCR2 and restrict the IPA
size differently depending on whether or not we have support for nested
translation.

Signed-off-by: Will Deacon <will.deacon@arm.com>
2014-09-02 10:04:43 +01:00
Hans Wennborg
70c9a7db93 iommu/arm-smmu: fix decimal printf format specifiers prefixed with 0x
The prefix suggests the number should be printed in hex, so use
the %x specifier to do that.

Found by using regex suggested by Joe Perches.

Signed-off-by: Hans Wennborg <hans@hanshq.net>
Signed-off-by: Will Deacon <will.deacon@arm.com>
2014-09-02 10:04:42 +01:00
Olav Haugan
3c8766d0ca iommu/arm-smmu: Do not access non-existing S2CR registers
The number of S2CR registers is not properly set when stream
matching is not supported. Fix this and add check that we do not try to
access outside of the number of S2CR regisrers.

Signed-off-by: Olav Haugan <ohaugan@codeaurora.org>
[will: added missing NUMSIDB_* definitions]
Signed-off-by: Will Deacon <will.deacon@arm.com>
2014-09-02 10:04:42 +01:00
Will Deacon
43b412bedb iommu/arm-smmu: fix s2cr and smr teardown on device detach from domain
When we attach a device to a domain, we configure the SMRs (if we have
any) to match the Stream IDs for the corresponding SMMU master and
program the s2crs accordingly. However, on detach we tear down the s2crs
assuming stream-indexing (as opposed to stream-matching) and SMRs
assuming they are present.

This patch fixes the device detach code so that it operates as a
converse of the attach code.

Cc: <stable@vger.kernel.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
2014-09-02 10:04:33 +01:00
Linus Walleij
a198420028 pinctrl: sh-pfc: use a saner Kconfig symbol
There is currently a kludge to get the Makefile to move down
to sh-pfc:s drivers: the arch definitions are used twice to
get it done. However we can very well use the Kconfig symbol
for the SH PFC pin control feature itself: it doesn't matter
that it comes from a lower leaf in the Kconfig hierarchy which
is completely orthogonal.

Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2014-09-02 10:53:05 +02:00
Linus Walleij
0752e169ba gpio: adnp: switch to use irqchip helpers
This switches the ADNP GPIO driver to use the gpiolib
irqchip helpers. Also do some random refactoring to make it
look like most other GPIO drivers.

Cc: Roland Stigge <stigge@antcom.de>
Cc: Lars Poeschel <poeschel@lemonage.de>
Cc: Thierry Reding <thierry.reding@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2014-09-02 10:44:01 +02:00
Axel Lin
e4946cdcab gpu: ipu-v3: Return proper error on ipu_add_client_devices error path
Avoid returning an uninitialized variable in the error path.

Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
2014-09-02 10:43:15 +02:00
Axel Lin
b6c044a3d8 gpu: ipu-v3: Select GENERIC_IRQ_CHIP to fix build error
This driver uses GENERIC_IRQ_CHIP, so it needs to select GENERIC_IRQ_CHIP to
avoid build error.

Fixes below build errors:
ERROR: "irq_alloc_domain_generic_chips" [drivers/gpu/ipu-v3/imx-ipu-v3.ko] undefined!
ERROR: "irq_gc_mask_clr_bit" [drivers/gpu/ipu-v3/imx-ipu-v3.ko] undefined!
ERROR: "irq_gc_mask_set_bit" [drivers/gpu/ipu-v3/imx-ipu-v3.ko] undefined!
ERROR: "irq_generic_chip_ops" [drivers/gpu/ipu-v3/imx-ipu-v3.ko] undefined!
ERROR: "irq_gc_ack_set_bit" [drivers/gpu/ipu-v3/imx-ipu-v3.ko] undefined!
ERROR: "irq_get_domain_generic_chip" [drivers/gpu/ipu-v3/imx-ipu-v3.ko] undefined!
make[1]: *** [__modpost] Error 1
make: *** [modules] Error 2

Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
2014-09-02 10:42:59 +02:00
Brian Norris
d6b9302f79 ARM: at91: add MTD_SPI_NOR (new dependency for M25P80)
This defconfig contains the CONFIG_M25P80 symbol, which is now
dependent on the MTD_SPI_NOR symbol. Add CONFIG_MTD_SPI_NOR to satisfy
the new dependency.

At the same time, drop the now-nonexistent CONFIG_MTD_CHAR symbol.

Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Cc: Andrew Victor <linux@maxim.org.za>
Cc: Jean-Christophe Plagniol-Villard <plagnioj@jcrosoft.com>
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
2014-09-02 10:36:13 +02:00
Christian Borntraeger
1951497d90 KVM: s390/mm: Fix guest storage key corruption in ptep_set_access_flags
commit 0944fe3f4a ("s390/mm: implement software referenced bits")
triggered another paging/storage key corruption. There is an
unhandled invalid->valid pte change where we have to set the real
storage key from the pgste.
When doing paging a guest page might be swapcache or swap and when
faulted in it might be read-only and due to a parallel scan old.
An do_wp_page will make it writeable and young. Due to software
reference tracking this page was invalid and now becomes valid.

Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Acked-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: stable@vger.kernel.org # v3.12+
2014-09-02 10:30:43 +02:00
Christian Borntraeger
3e03d4c46d KVM: s390/mm: Fix storage key corruption during swapping
Since 3.12 or more precisely  commit 0944fe3f4a ("s390/mm:
implement software referenced bits") guest storage keys get
corrupted during paging. This commit added another valid->invalid
translation for page tables - namely ptep_test_and_clear_young.
We have to transfer the storage key into the pgste in that case.

Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Acked-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: stable@vger.kernel.org # v3.12+
2014-09-02 10:30:43 +02:00
Ludovic Desroches
d24cd78399 ARM: at91: sama5d3: add usart dma configurations
Add the DMA configuration for USARTs mainly because it is not obvious to
add the FIFO flag which is needed for rx.

Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
2014-09-02 10:24:22 +02:00
Linus Walleij
0dbc8b7afe gpio: move varargs hack outside #ifdef GPIOLIB
commit 39b2bbe3d7
"gpio: add flags argument to gpiod_get*() functions"
added a dynamic flags argument to all the GPIOD getter
functions, however this did not cover the stubs so
when people used gpiod stubs to compile out descriptor
code, compilation failed.

Solve this by:
- Also rename all the stub functions __gpiod_*
- Moving the vararg hack outside of #ifdef CONFIG_GPIOLIB
  so these will always be available.

Reviewed-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2014-09-02 10:09:43 +02:00
Michal Kazior
e556f11184 ath10k: stop monitor vdev for sta assoc
This prevents some fw revisions from crashing in
many cases when user is trying to run a
promiscuous station interface (e.g. sniffing,
4addr bridge).

Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
2014-09-02 10:28:47 +03:00
Michal Kazior
1933747f5c ath10k: fix monitor start/stop sequences
Fix some cases where monitor start failure left
the driver in a confused state.

This also makes the monitor code simpler.

Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
2014-09-02 10:28:36 +03:00
Chao Yu
b73e52824c f2fs: reposition unlock_new_inode to prevent accessing invalid inode
As the race condition on the inode cache, following scenario can appear:
[Thread a]				[Thread b]
					->f2fs_mkdir
					  ->f2fs_add_link
					    ->__f2fs_add_link
					      ->init_inode_metadata failed here
->gc_thread_func
  ->f2fs_gc
    ->do_garbage_collect
      ->gc_data_segment
        ->f2fs_iget
          ->iget_locked
            ->wait_on_inode
					  ->unlock_new_inode
        ->move_data_page
					  ->make_bad_inode
					  ->iput

When we fail in create/symlink/mkdir/mknod/tmpfile, the new allocated inode
should be set as bad to avoid being accessed by other thread. But in above
scenario, it allows f2fs to access the invalid inode before this inode was set
as bad.
This patch fix the potential problem, and this issue was found by code review.

change log from v1:
 o Add condition judgment in gc_data_segment() suggested by Changman Lee.
 o use iget_failed to simplify code.

Signed-off-by: Chao Yu <chao2.yu@samsung.com>
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
2014-09-02 00:22:24 -07:00
Michal Kazior
2139627172 ath10k: kill tasklets after free_irq
Commit 5c771e7454
introduced a regression. On some systems spurious
interrupts could schedule a tasklet while tearing
down leading to, e.g.:

 BUG: unable to handle kernel paging request at fe589030
 IP: [<c1316fb0>] ioread32+0x30/0x40
 ...
 Call Trace:
  [<fe576c1b>] ath10k_pci_tasklet+0x1b/0x60 [ath10k_pci]
  [<c1053fbe>] tasklet_action+0x9e/0xb0
  [<c10534f1>] __do_softirq+0xf1/0x3f0
  [<c1053400>] ? ftrace_raw_event_irq_handler_entry+0xa0/0xa0
  [<c1004999>] do_softirq_own_stack+0x29/0x40
  <IRQ>
  [<c1053a76>] irq_exit+0x86/0xb0
 ...
  [<c132d522>] do_pci_disable_device+0x52/0x60
  [<c132d57f>] pci_disable_device+0x4f/0xb0
  [<c132a961>] ? __pci_set_master+0x51/0x80
  [<fe5740b3>] ath10k_pci_release+0x33/0x40 [ath10k_pci]
  [<fe575d4b>] ath10k_pci_remove+0x7b/0x90 [ath10k_pci]

Reported-by: Kalle Valo <kvalo@qca.qualcomm.com>
Tested-by: Kalle Valo <kvalo@qca.qualcomm.com>
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
2014-09-02 10:18:36 +03:00
Michal Kazior
a4841eb639 ath10k: fix num_legacy_stations tracking
If a station was reassociated, i.e. due to change
of supported rates update via sta_rc_update() the
num_legacy_stations would be (incorrectly) bumped
up leading to unbalanced usage of the var. This in
turn could lock rtscts protection up as enabled.

Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
2014-09-02 10:16:54 +03:00
Michal Kazior
e75db4e368 ath10k: re-enable interrupts properly in hw recovery
Recent changes done to start/restart sequences
broke hw recovery in some hw configurations. The
pci transport was stopped twice however due to a
workaround in the pci disabling code the
disable/enable for first msi interrupt was not
balanced. This ended up with irqs not being
properly re-enabled and the following print out
during recovery:

 ath10k: failed to receive control response completion, polling..
 ath10k: Service connect timeout: -110
 ath10k: Could not init core: -110

Legacy interrupt mode was unaffected while msi
ranged mode would be partially crippled (it would
miss fw indication interrupts but otherwise it
worked fine).

This fixes completely broken fw recovery for a
single msi interrupt mode and fixes subsequent fw
crash reports for msi range interrupt mode.

Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
2014-09-02 10:13:26 +03:00
Borislav Petkov
f4ce6eca71 EDAC: Fix mem_types strings type
This one got forgotten during an earlier cleanup.

Signed-off-by: Borislav Petkov <bp@suse.de>
2014-09-02 09:11:16 +02:00
David S. Miller
88e4194712 Merge branch 'cxgb4'
Hariprasad Shenai says:

====================
Trivial fixes for cxgb4

This patch series adds support to fix T5 adapter accessing T4 adapter registers,
issue mbox command on correct mbox for physical function, avoid dumping write
only registers, use correct length for adapter part number and support to detect
and display firmware reported errors.

The patches series is created against 'net' tree.
And includes patches on cxgb4 driver.

We have included all the maintainers of respective drivers. Kindly review the
change and let us know in case of any review comments.

Thanks

V2:
   Added description for each patch as per David Miller's comment
====================

Signed-off-by: David S. Miller <davem@davemloft.net>
2014-09-01 23:00:49 -07:00
Hariprasad Shenai
5c937dd3f9 cxgb4: Issue mbox commands on correct mbox
A couple of RDMA-related called to t4_query_params() were issuing mbox commands
on mbox0 instead of mbox4.

Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-09-01 23:00:42 -07:00
Hariprasad Shenai
3d9103f80d cxgb4: Avoid dumping Write-only registers in register dump
Avoid dumping MPS_RPLC_MAP_CTL for reg dumps; this is a Write-Only register.
Reading this register may cause MPS TCAM corruption.

Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-09-01 23:00:42 -07:00
Hariprasad Shenai
31d55c2d66 cxgb4: Detect and display firmware reported errors
The adapter firmware can indicate error conditions to the host.
If the firmware has indicated an error, print out the reason for
the firmware error.

Based on original work by Casey Leedom <leedom@chelsio.com>

Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-09-01 23:00:41 -07:00
Hariprasad Shenai
9bb59b96ae cxgb4: Fix T5 adapter accessing T4 adapter registers
Fixes few register access for both T4 and T5.
PCIE_CORE_UTL_SYSTEM_BUS_AGENT_STATUS & PCIE_CORE_UTL_PCI_EXPRESS_PORT_STATUS
is T4 only register don't let T5 access them. For T5 MA_PARITY_ERROR_STATUS2
is additionally read. MPS_TRC_RSS_CONTROL is T4 only register, for T5 use
MPS_T5_TRC_RSS_CONTROL.

Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-09-01 23:00:41 -07:00
Hariprasad Shenai
63a92fe6f7 cxgb4: Fixed the code to use correct length for part number
Previously it was using the length value of serial number.
Also added macro for VPD unique identifier (0x82).

Signed-off-by: Casey Leedom <leedom@chelsio.com>
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-09-01 23:00:41 -07:00
Hariprasad Shenai
444018a7f1 cxgb4: Fix for handling 1Gb/s SFP+ Transceiver Modules
We previously assumed that a Port's Capabilities and Advertised Capabilities
would never change from Port Initialization time.  This is no longer true
when we can have 10Gb/s and 1Gb/s SFP+ Transceiver Modules randomly swapped.

Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-09-01 23:00:41 -07:00
Takashi Iwai
acf08081ad ALSA: hda - Fix COEF setups for ALC1150 codec
ALC1150 codec seems to need the COEF- and PLL-setups just like its
compatible ALC882 codec.  Some machines (e.g. SunMicro X10SAT) show
the problem like too low output volumes unless the COEF setup is
applied.

Reported-and-tested-by: Dana Goyette <danagoyette@gmail.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
2014-09-02 07:21:56 +02:00
Giuseppe CAVALLARO
cc25f0cbe4 stmmac: only remove RXCSUM feature if no rx coe is available
In case of the HW is not able to do the receive checksum offloading
the only feature to remove is NETIF_F_RXCSUM.

Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-09-01 21:51:29 -07:00
Giuseppe CAVALLARO
d2afb5bdff stmmac: fix the rx csum feature
For new GMACs it is possible to turn-on/off the COE.
In the current driver, when disabled the Rx-checksum
via ethtool, the tool reported that csum was disabled
but the HW continued to set the IPC. Indeed this is
because the fix_features allows this. So the patch
fixes this problem by adding the set_features.

Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-09-01 21:51:29 -07:00
Willem de Bruijn
364a9e9324 sock: deduplicate errqueue dequeue
sk->sk_error_queue is dequeued in four locations. All share the
exact same logic. Deduplicate.

Also collapse the two critical sections for dequeue (at the top of
the recv handler) and signal (at the bottom).

This moves signal generation for the next packet forward, which should
be harmless.

It also changes the behavior if the recv handler exits early with an
error. Previously, a signal for follow-up packets on the errqueue
would then not be scheduled. The new behavior, to always signal, is
arguably a bug fix.

For rxrpc, the change causes the same function to be called repeatedly
for each queued packet (because the recv handler == sk_error_report).
It is likely that all packets will fail for the same reason (e.g.,
memory exhaustion).

This code runs without sk_lock held, so it is not safe to trust that
sk->sk_err is immutable inbetween releasing q->lock and the subsequent
test. Introduce int err just to avoid this potential race.

Signed-off-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-09-01 21:49:08 -07:00
Willem de Bruijn
8fe2f761ca net-timestamp: expand documentation
Expand Documentation/networking/timestamping.txt with new
interfaces and bytestream timestamping. Also minor
cleanup of the other text.

Import txtimestamp.c test of the new features.

Signed-off-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-09-01 21:49:08 -07:00
David S. Miller
c5a65680b3 Merge branch 'csums-next'
Tom Herbert says:

====================
net: Checksum offload changes - Part VI

I am working on overhauling RX checksum offload. Goals of this effort
are:

- Specify what exactly it means when driver returns CHECKSUM_UNNECESSARY
- Preserve CHECKSUM_COMPLETE through encapsulation layers
- Don't do skb_checksum more than once per packet
- Unify GRO and non-GRO csum verification as much as possible
- Unify the checksum functions (checksum_init)
- Simplify code

What is in this seventh patch set:

- Add skb->csum. This allows a device or GRO to indicate that an
  invalid checksum was detected.
- Checksum unncessary to checksum complete conversions.

With these changes, I believe that the third goal of the overhaul is
now mostly achieved. In the case of no encapsulation or one layer of
encapsulation, there should only be at most one skb_checksum over
each packet (between GRO and normal path). In the case of two layers
of encapsulation, it is still possible with the right combination of
non-zero and zero UDP checksums to have >1 skb_checksum. For instance:
IP>GRE(with csum)>IP>UDP(zero csum)>VXLAN>IP>UDP(non-zero csum),
would likely necessiate an skb_checksum in GRO and normal path.
This doesn't seem like a common scenario at all so I'm inclined to
not address this now, if multiple layers of encapsulation becomes
popular we can reassess.

Note that checksum conversion shows a nice improvement for RX VXLAN when
outer UDP checksum is enabled (12.65% CPU compared to 20.94%). This
is not only from the fact that we don't need checksum calculation on
the host, but also allows GRO for VXLAN in this case. Checksum
conversion does not help send side (which still needs to perform
a checksum on host). For that we will implement remote checksum offload
in a later patch
(http://tools.ietf.org/html/draft-herbert-remotecsumoffload-00).

Please review carefully and test if possible, mucking with basic
checksum functions is always a little precarious :-)
====================

Signed-off-by: David S. Miller <davem@davemloft.net>
2014-09-01 21:36:35 -07:00
Tom Herbert
72297c59f7 l2tp: Enable checksum unnecessary conversions for l2tp/UDP sockets
Signed-off-by: Tom Herbert <therbert@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-09-01 21:36:28 -07:00
Tom Herbert
c60c308cbd vxlan: Enable checksum unnecessary conversions for vxlan/UDP sockets
Signed-off-by: Tom Herbert <therbert@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-09-01 21:36:28 -07:00
Tom Herbert
884d338c04 gre: Add support for checksum unnecessary conversions
Call skb_checksum_try_convert and skb_gro_checksum_try_convert
after checksum is found present and validated in the GRE header
for normal and GRO paths respectively.

In GRO path, call skb_gro_checksum_try_convert

Signed-off-by: Tom Herbert <therbert@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-09-01 21:36:28 -07:00
Tom Herbert
2abb7cdc0d udp: Add support for doing checksum unnecessary conversion
Add support for doing CHECKSUM_UNNECESSARY to CHECKSUM_COMPLETE
conversion in UDP tunneling path.

In the normal UDP path, we call skb_checksum_try_convert after locating
the UDP socket. The check is that checksum conversion is enabled for
the socket (new flag in UDP socket) and that checksum field is
non-zero.

In the UDP GRO path, we call skb_gro_checksum_try_convert after
checksum is validated and checksum field is non-zero. Since this is
already in GRO we assume that checksum conversion is always wanted.

Signed-off-by: Tom Herbert <therbert@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-09-01 21:36:28 -07:00
Tom Herbert
d96535a17d net: Infrastructure for checksum unnecessary conversions
For normal path, added skb_checksum_try_convert which is called
to attempt to convert CHECKSUM_UNNECESSARY to CHECKSUM_COMPLETE. The
primary condition to allow this is that ip_summed is CHECKSUM_NONE
and csum_valid is true, which will be the state after consuming
a CHECKSUM_UNNECESSARY.

For GRO path, added skb_gro_checksum_try_convert which is the GRO
analogue of skb_checksum_try_convert. The primary condition to allow
this is that NAPI_GRO_CB(skb)->csum_cnt == 0 and
NAPI_GRO_CB(skb)->csum_valid is set. This implies that we have consumed
all available CHECKSUM_UNNECESSARY checksums in the GRO path.

Signed-off-by: Tom Herbert <therbert@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-09-01 21:36:27 -07:00
Tom Herbert
5a21232983 net: Support for csum_bad in skbuff
This flag indicates that an invalid checksum was detected in the
packet. __skb_mark_checksum_bad helper function was added to set this.

Checksums can be marked bad from a driver or the GRO path (the latter
is implemented in this patch). csum_bad is checked in
__skb_checksum_validate_complete (i.e. calling that when ip_summed ==
CHECKSUM_NONE).

csum_bad works in conjunction with ip_summed value. In the case that
ip_summed is CHECKSUM_NONE and csum_bad is set, this implies that the
first (or next) checksum encountered in the packet is bad. When
ip_summed is CHECKSUM_UNNECESSARY, the first checksum after the last
one validated is bad. For example, if ip_summed == CHECKSUM_UNNECESSARY,
csum_level == 1, and csum_bad is set-- then the third checksum in the
packet is bad. In the normal path, the packet will be dropped when
processing the protocol layer of the bad checksum:
__skb_decr_checksum_unnecessary called twice for the good checksums
changing ip_summed to CHECKSUM_NONE so that
__skb_checksum_validate_complete is called to validate the third
checksum and that will fail since csum_bad is set.

Signed-off-by: Tom Herbert <therbert@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-09-01 21:36:27 -07:00
hayeswang
52aec126c4 r8152: rename rx_buf_sz
The variable "rx_buf_sz" is used by both tx and rx buffers. Replace
it with "agg_buf_sz".

Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-09-01 20:41:45 -07:00
Florian Fainelli
4559154a58 net: phy: mdio-bcm-unimac: NULL-terminate unimac_mdio_ids
drivers/net/phy/mdio-bcm-unimac.c:195:37-38: unimac_mdio_ids is not NULL
terminated at line 195

Make sure of_device_id tables are NULL terminated
Generated by: scripts/coccinelle/misc/of_table.cocci

Signed-off-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-09-01 20:41:45 -07:00
Florian Fainelli
61b7363ffa net: dsa: make dsa_pack_type static
net/dsa/dsa.c:624:20: sparse: symbol 'dsa_pack_type' was not declared.
Should it be static?

Fixes: 3e8a72d1da ("net: dsa: reduce number of protocol hooks")
Signed-off-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-09-01 20:41:45 -07:00
David S. Miller
8a3cf39b72 Merge branch 'amd-xgbe-net'
Tom Lendacky says:

====================
amd-xgbe: AMD XGBE driver fixes 2014-08-29

The following series of patches includes fixes to the driver.

- Tx hardware queue flushing support dependent on hardware version
- Incorrect reported fifo size
- Proper mmd select in XPCS debugfs support
- Proper queue count for configuring Tx flow control

This patch series is based on net.
====================

Signed-off-by: David S. Miller <davem@davemloft.net>
2014-09-01 20:38:48 -07:00
Lendacky, Thomas
9fc69affda amd-xgbe: Use the Tx queue count for Tx flow control support
When configuring Tx flow control the Rx queue count was used instead of
the Tx queue count for looping through the Tx hardware queues. Fix the
code to use the Tx queue count.

Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-09-01 20:38:14 -07:00
Lendacky, Thomas
625c8e4a2f amd-xgbe: Fix the xpcs mmd debugfs support
The debugfs support for the xpcs registers did not properly use the
specified mmd (xpcs_mmd entry) which resulted in the default mmd
value always being used.  Update the debugfs support to generate the
proper mmd register value.

Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-09-01 20:38:14 -07:00
Lendacky, Thomas
f076f45372 amd-xgbe: Reported fifo size from hardware is not correct
The fifo size reported by the hardware is not correct. Add support
to limit the reported size to what is actually present.  Also, fix
the argument types used in the fifo size calculation function.

Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-09-01 20:38:14 -07:00
Lendacky, Thomas
a9a4a2d9d6 amd-xgbe: Check for Tx hardware queue flushing support
The flushing of the Tx hardware queues is only supported at a certain
level of the hardware.  Retrieve the current version of the hardware
and use that to determine if flushing is supported.

Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-09-01 20:38:14 -07:00
Geert Uytterhoeven
e148e1bf6f drivers: net: NET_XGENE should depend on HAS_DMA
If NO_DMA=y:

drivers/built-in.o: In function `xgene_enet_delete_ring':
xgene_enet_main.c:(.text+0x28755a): undefined reference to `dma_free_coherent'
drivers/built-in.o: In function `xgene_enet_setup_tx_desc':
xgene_enet_main.c:(.text+0x287774): undefined reference to `dma_map_single'
xgene_enet_main.c:(.text+0x287780): undefined reference to `dma_mapping_error'
drivers/built-in.o: In function `xgene_enet_tx_completion':
xgene_enet_main.c:(.text+0x2878e6): undefined reference to `dma_unmap_single'
drivers/built-in.o: In function `xgene_enet_refill_bufpool':
xgene_enet_main.c:(.text+0x2879d4): undefined reference to `dma_map_single'
xgene_enet_main.c:(.text+0x2879e0): undefined reference to `dma_mapping_error'
drivers/built-in.o: In function `xgene_enet_rx_frame':
xgene_enet_main.c:(.text+0x287aaa): undefined reference to `dma_unmap_single'
drivers/built-in.o: In function `xgene_enet_free_desc_ring':
xgene_enet_main.c:(.text+0x287f98): undefined reference to `dma_free_coherent'
drivers/built-in.o: In function `xgene_enet_create_desc_ring':
xgene_enet_main.c:(.text+0x28808e): undefined reference to `dma_alloc_coherent'
drivers/built-in.o: In function `xgene_enet_probe':
xgene_enet_main.c:(.text+0x2883d4): undefined reference to `dma_set_mask'
xgene_enet_main.c:(.text+0x2883ec): undefined reference to `dma_supported'

Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-09-01 20:33:15 -07:00
Zheng Liu
eb68d0e2fc ext4: track extent status tree shrinker delay statictics
This commit adds some statictics in extent status tree shrinker.  The
purpose to add these is that we want to collect more details when we
encounter a stall caused by extent status tree shrinker.  Here we count
the following statictics:
  stats:
    the number of all objects on all extent status trees
    the number of reclaimable objects on lru list
    cache hits/misses
    the last sorted interval
    the number of inodes on lru list
  average:
    scan time for shrinking some objects
    the number of shrunk objects
  maximum:
    the inode that has max nr. of objects on lru list
    the maximum scan time for shrinking some objects

The output looks like below:
  $ cat /proc/fs/ext4/sda1/es_shrinker_info
  stats:
    28228 objects
    6341 reclaimable objects
    5281/631 cache hits/misses
    586 ms last sorted interval
    250 inodes on lru list
  average:
    153 us scan time
    128 shrunk objects
  maximum:
    255 inode (255 objects, 198 reclaimable)
    125723 us max scan time

If the lru list has never been sorted, the following line will not be
printed:
    586ms last sorted interval
If there is an empty lru list, the following lines also will not be
printed:
    250 inodes on lru list
  ...
  maximum:
    255 inode (255 objects, 198 reclaimable)
    0 us max scan time

Meanwhile in this commit a new trace point is defined to print some
details in __ext4_es_shrink().

Cc: Andreas Dilger <adilger.kernel@dilger.ca>
Cc: Jan Kara <jack@suse.cz>
Reviewed-by: Jan Kara <jack@suse.cz>
Signed-off-by: Zheng Liu <wenqing.lz@taobao.com>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
2014-09-01 22:26:49 -04:00