The Data Modul TP 72037 EasyTouch controller is derived from EGALAX
controller and is capable of detecting dual contacts. Packets can be 5
bytes or 10 bytes long, depending whether one or two contacts are
detected. Format is same as EGALAX touch controller, but with x and y
coordinates inverted.
Signed-off-by: Armando Visconti <armando.visconti@st.com>
Signed-off-by: Viresh Kumar <viresh.kumar@st.com>
Signed-off-by: Daniel Ritz <daniel.ritz@gmx.ch>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Even if cards supports 1.8V I/O voltage those should anyway be
initialized at 3.3V I/O according to (e)MMC, SD and SDIO specs.
Some eMMC and embedded SDIO devices are able to be initialized
at 1.8V as well, but it is better to be safe.
Do note that initialization in this context means that the card
has been completely powered off, otherwise the card will remain
at the last I/O voltage level that were negotitiated.
Due to the above being taken care of the suspend/resume issues
for UHS-I SD-cards has been fixed.
Signed-off-by: Ulf Hansson <ulf.hansson@stericsson.com>
Acked-by: Philip Rakity <prakity@marvell.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Tested-by: Subhash Jadavani <subhashj@codeaurora.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
On a system with large pages (64k in my case), the following BUG is
triggered in MMC core:
[ 2.338023] BUG: failure at drivers/mmc/core/core.c:221/mmc_start_request()!
[ 2.338102] Kernel panic - not syncing: BUG!
[ 2.338155] Call trace:
[ 2.338228] [<ffffffc00008635c>] dump_backtrace+0x0/0x120
[ 2.338317] [<ffffffc0003365ec>] dump_stack+0x14/0x1c
[ 2.338403] [<ffffffc000336990>] panic+0xbc/0x1f0
[ 2.338498] [<ffffffc00027a494>] mmc_start_request+0x154/0x184
[ 2.338600] [<ffffffc00027abdc>] mmc_start_req+0x110/0x140
[ 2.338701] [<ffffffc00028604c>] mmc_blk_issue_rw_rq+0x7c/0x39c
[ 2.338804] [<ffffffc00028652c>] mmc_blk_issue_rq+0x1c0/0x468
[ 2.338905] [<ffffffc000287564>] mmc_queue_thread+0x68/0x118
[ 2.338995] [<ffffffc0000bc308>] kthread+0x84/0x8c
This is because of a 64k request with a max_req_size of 64k-1 bytes.
The following patch fixes the problem by limiting the max_blk_count
such that max_blk_count * max_blk_size == max_req_size. I couldn't
pursuade the compiler to emit a shift instead of a div without encoding
the shift explicitly.
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
On i.MX53 we have to write a special SDHCI_CMD_ABORTCMD to the
SDHCI_TRANSFER_MODE register during a MMC_STOP_TRANSMISSION
command. This works for SD cards. However, with MMC cards
the MMC_SET_BLOCK_COUNT command is used instead, but this
needs the same handling. Fix MMC cards by testing for the
MMC_SET_BLOCK_COUNT command aswell. Tested on a custom i.MX53
board with a Transcend MMC+ card and eMMC.
The kernel started used MMC_SET_BLOCK_COUNT in 3.0, so this
is a regression for these boards introduced in 3.0; it should
go to 3.0/3.1/3.2-stable.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Cc: <stable@vger.kernel.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
A recent commit "mmc: core: Use delayed work in clock gating framework"
(597dd9d79c) introduced a default 200ms delay before clock gating
actually takes place. This means that every time an MMC interface
becomes idle it first stays on for 200ms before gating its clock. This
leads to increased power consumption and is therefore a clear regression.
This patch restores the original behaviour by setting the default delay
to 0. Users prioritising throughput over power efficiency can still
modify the delay via sysfs.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Chris Ball <cjb@laptop.org>
This patch adds support for TI's touchscreen
controller for a 4/5/8 wire resistive panel
that is directly fed to the ADC.
This touchscreen controller will be part of
AM335x TI SoC. The TRM can be found at:
http://www.ti.com/lit/ug/spruh73a/spruh73a.pdf
Signed-off-by: Patil, Rachna <rachna@ti.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
This patch removes redundant bits per pixel information by using the
one storged in var directly. Simplifies code without any functional
changes.
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
dev_dbg() in rpmsg_probe() made use of the %x formatting that
expects an 'unsigned int' which dma_addr_t is not in cases where
dma_addr_t is 64-bit (CONFIG_ARCH_DMA_ADDR_T_64BIT). Casting to
a 'unsigned long long' and using %llx will avoid this.
Signed-off-by: Mark Asselstine <mark.asselstine@windriver.com>
CC: Ohad Ben-Cohen <ohad@wizery.com>
CC: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Ohad Ben-Cohen <ohad@wizery.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.18 (GNU/Linux)
iQEcBAABAgAGBQJPUrf8AAoJEDeqqVYsXL0Ma0cH/1hcV4G3U7ZNbKJsijl7eowP
GON1pme9XvUIHxWibIEZhUaaycWhN3oaShdEO+IAYSVoRSC6pu1H+/Be8VgvVpdT
+1N9a41sXmuMeTadwfdZJ6k0Gs9gtbuxfvO4Z6WRbrpjik5S/3ZP3A/US8jESbCW
rOK9evTUCs+rBFXiyOwyz3Li335/zEbq3E3N14VgbA05vYvw3+AuNQ0e8zS2A9/D
3yLiQfIPhVZmH5majf+4qqyvBqQ0Jacj5TZrKyRehYZpB1c+fHwTDRYBko9vWdEH
Tojk/mz3hPu48BNJyawb0Kemei+hNGKyejj8jbjBT1cb8/FTOGeZsYRa83YA6Hg=
=joKr
-----END PGP SIGNATURE-----
Merge tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi-rc-fixes-2.6
SCSI fixes from James Bottomley:
"There's just a single fix in here: the osd max device number fix."
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi-rc-fixes-2.6:
[SCSI] osd_uld: Bump MAX_OSD_DEVICES from 64 to 1,048,576
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.18 (GNU/Linux)
iQEcBAABAgAGBQJPUqnkAAoJEDeqqVYsXL0MyTwH/14R9sIt+IdQgMGje6Dys6U1
3wxmNHcxNBB461212i+XVToH72GiPtUyWY8Q3LT+Qcq4Rab9oq8wDffxdgflDLja
sZq9COLR8dmXJM0hduyuysCiNIlmuURV20uIMsDbYutBVtAKKqMd7ZrJBmkVh7xT
slBJf+0lcD5IBYPYwf8lbxAI7E/C5TarMCIZk4z21I8ovF321RlGcyyo6NM62q/P
wvLw4bJuW7nJa3q3B7BznzBcoHLmzo9tiY+CbtQlGhSdasDKJ8HuAegTVyofl6s8
0/RTvaUcqTWUlFxXzLVDT+MCWAUP4GFR66tR2T5tygRi9st70TcpMzISiyZzKi8=
=WzAJ
-----END PGP SIGNATURE-----
Merge tag 'parisc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/parisc-2.6
PARISC fixes from James Bottomley:
"This is a set of build fixes to get the cross compiled architecture
testbeds building again"
* tag 'parisc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/parisc-2.6:
[PARISC] don't unconditionally override CROSS_COMPILE for 64 bit.
[PARISC] include <linux/prefetch.h> in drivers/parisc/iommu-helpers.h
[PARISC] fix compile break caused by iomap: make IOPORT/PCI mapping functions conditional
Some user scenarios need to prioritize performance over
maxiumum resolution.
Also, some devices may have bad vendor descriptors, and
this allows the user to set a pixel limit that matches
their specific device to avoid blank screens on higher
resolution monitors.
700000 minimum for DL-115, 2360000 maximum for DL-195
Signed-off-by: Ben Collins <bcollins@ubuntu.com>
Signed-off-by: Bernie Thompson <bernie@plugable.com>
The driver was not using le16_to_cpu when reading keys from the vendor
descriptor, causing incorrect parsing. Mainly, sku_pixel_limit was not
being parsed on big-endian systems. This would result in a blank screen
on big-endian CPUs where the DL chips's max mode was smaller than the
monitor's native mode.
Signed-off-by: Ben Collins <bcollins@ubuntu.com>
Signed-off-by: Bernie Thompson <bernie@plugable.com>
"mem" is type u8. We need parenthesis here or it screws up the pointer
math probably leading to an oops.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Cc: stable@kernel.org
Acked-by: Jeff Garzik <jgarzik@redhat.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Pull from Herbert Xu:
"This push fixes a bug in mv_cesa that causes all hash operations
that supply data on a final operation to fail."
* git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6:
crypto: mv_cesa - fix final callback not ignoring input data
This patch adds the specific part which handles the PCAN-USB Pro adapter
from PEAK-System Technik (http://www.peak-system.com). The PCAN-USB Pro
adapter is a dual-channel USB 2.0 adapter compliant with CAN specifications
Tested-by: Oliver Hartkopp <socketcan@hartkopp.net>
Acked-by: Wolfgang Grandegger <wg@grandegger.com>
Signed-off-by: Stephane Grosjean <s.grosjean@peak-system.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
This patch adds the specific part which handles the PCAN-USB adapter from
PEAK-System Technik (http://www.peak-system.com). The PCAN-USB adapter is
a sja1000 based, mono-channel USB 1.1 adapter compliant with CAN
specifications 2.0A (11-bit ID) and 2.0B (29-bit ID).
Tested-by: Oliver Hartkopp <socketcan@hartkopp.net>
Acked-by: Wolfgang Grandegger <wg@grandegger.com>
Signed-off-by: Stephane Grosjean <s.grosjean@peak-system.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
This patch adds the core of the peak_usb driver which handles PEAK-System
Technik PCAN USB adapters. It defines the parts which are common to the
PCAN-USB adapters: can network interfaces management, network-to/from-usb
data path interface, timestamps management...
Tested-by: Oliver Hartkopp <socketcan@hartkopp.net>
Acked-by: Wolfgang Grandegger <wg@grandegger.com>
Signed-off-by: Stephane Grosjean <s.grosjean@peak-system.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
This patch adds support to the PCAN-PC Card PCMCIA card from
PEAK-System Technik (www.peak-system.com). This card is a CAN interface
for the PC Card slot. It is available as a single or dual-channel version.
Tested-by: Oliver Hartkopp <socketcan@hartkopp.net>
Acked-by: Dominik Brodowski <linux@dominikbrodowski.net>
Signed-off-by: Stephane Grosjean <s.grosjean@peak-system.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
This patch adds the support of some new PEAK-System PCI cards in the CAN
network sub-system. These are:
PCAN-PCIeC (PCI-ExpressCard)
PCAN-mminiPCI (mini-PCI)
PCAN-PCI (PCI next-gen)
This patch also adds the control of the blinking leds of the PCAN-PCIeC.
Tested-by: Oliver Hartkopp <socketcan@hartkopp.net>
Acked-by: Wolfgang Grandegger <wg@grandegger.com>
Signed-off-by: Stephane Grosjean <s.grosjean@peak-system.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
drivers/net/can/cc770/cc770.c included 'linux/can/dev.h' twice,
remove the duplicate.
Signed-off-by: Danny Kukawka <danny.kukawka@bisect.de>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Some devices require a regulator to work, but boards may not have
a software controllable regulator for this device. Provide a helper
function to make it simpler for these boards to register a fixed
regulator as a dummy regulator.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This patches fixes two things:
* Use gpio_valid function to check gpio before usage
This must be done after 63b4c29678 which uses -EINVAL for unused pin's
* Use gpio_to_irq to convert gpio's to irq
The driver assumed a 1:1 mapping between gpio and irq numbers. This is no
longer true after d0fbda9add.
Tested on custom RM9200 board with 8gb CF card.
Signed-off-by: Joachim Eastwood <joachim.eastwood@jotron.com>
Acked-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
If pxa2xx_drv_pcmcia_add_one fails, it will go to err1 error path.
Add a missing clk_put in the error path.
Checking the ret value after the for loop is redundant, it is always false.
Thus remove the redundant checking.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Eric Miao <eric.y.miao@gmail.com>
Acked-by: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Convert static struct pci_device_id *[] to static DEFINE_PCI_DEVICE_TABLE
tables. Also convert to use PCI_DEVICE macro for better readablity.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
This patch converts the drivers in drivers/pcmcia/* to use the
module_platform_driver() macro which makes the code smaller and a bit
simpler.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Wolfram Sang <w.sang@pengutronix.de>
Acked-by: Olof Johansson <olof@lixom.net>
Acked-by: Michael Hennerich <michael.hennerich@analog.com>
Acked-by: Marc Zyngier <maz@misterjones.org> [for the viper part]
Acked-by: Manuel Lauss <manuel.lauss@googlemail.com> [for the db1xxx_ss.c part]
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Since commit [e58aa3d2: genirq: Run irq handlers with interrupts disabled],
We run all interrupt handlers with interrupts disabled
and we even check and yell when an interrupt handler
returns with interrupts enabled (see commit [b738a50a:
genirq: Warn when handler enables interrupts]).
So now this flag is a NOOP and can be removed.
Signed-off-by: Yong Zhang <yong.zhang0@gmail.com>
Acked-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
{g|s}etnumtcs() today returns a u8 that is only used by the DCB code
to verify no error occurred. Today the driver implementations return
negative error codes which end up being non-zero so the logic works
out but triggers some sparse warnings.
To fix the sparse warnings convert the return value to an int.
CC: Eilon Greenstein <eilong@broadcom.com>
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
dcb netlink code calls setup_tc to init hardware traffic classes
to use for DCB. At some call sites the return values are not
checked for errors and in one case may return -EINVAL back to
the net/dcbnl.c caller which is expecting a u8.
This fixes some smatch hits and although failures are never
seen in practive its best to check return codes.
Reported-by: Dan Carenter <dan.carpenter@oracle.com>
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Ben Greear <greearb@candelatech.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The old code would += the total errors every time
stats were gathered. Instead, keep a count of short-pkt
and long-pkt counters and then simply add them together
for the rx-over-length stat.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The kernel already has a debug allocator, no need to have one unique to
a single driver. So delete it, replace with kfree, kmalloc, and, in a
few places that need it, kzalloc().
Cc: Chris Kelly <ckelly@ozmodevices.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Memory is being allocated by kmalloc and stored in
variable pstAddIndication. However, this memory is
not being freed in all cases. Therefore, this patch
frees it on several exit paths. This patch also
removes a whitespace.
Signed-off-by: Kevin McKinney <klmckinney1@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It seems the USB device ID 0bda:8192 is wrongly assigned to the
RTL8192SU chip and not to the RTL8191SU chip in the USB database.
So this patch moves this device ID from the rtl8192u staging
driver to the rtl8712 staging driver.
This patch was tested with a Radicom WIFIHU embedded wireless
module with a RTL8191SU chip and the USB device ID 0bda:8192.
Without the patch the rtl8192u driver claims this device, but
it does not work. With the patch the rtl8712 driver services
this device and it works.
Signed-off-by: Martin Krause <martin.krause@tqs.de>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Remove copies of the double USB device IDs:
- 0bda:8172
- 0bda:8174
Signed-off-by: Martin Krause <martin.krause@tqs.de>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
No functional changes.
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Acked-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Drivers may not need setup_ops at all, so let the core supply
some empty ops.
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Acked-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Changes since V1:
Exclude iio debugfs code in case CONFIG_DEBUG_FS isn't enabled.
Introduce helper function iio_get_debugfs_dentry.
Document additions to struct iio_dev
iio_debugfs_read_reg:
Use snprintf.
Use a shorter fixed length.
Introduce len instead of pointer math.
iio_debugfs_write_reg:
Fix return value use PT_ERR.
Changes since V2:
Use debugfs_remove.
Fix whitespace damage.
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Acked-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The below patch fixes some comments and some typos that I have found
while reading drivers/staging/iio/*
Signed-off-by: Justin P. Mattock <justinmattock@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
app_id comes from the network and can't be trusted. If it's zero then
it will lead to a kernel crash.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Chris Kelly <ckelly@ozmodevices.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This fixes following compilation warning:
drivers/misc/bmp085.c: In function ‘bmp085_get_pressure’:
drivers/misc/bmp085.c:238:4: warning: comparison of distinct pointer
types lacks a cast [enabled by default]
Signed-off-by: Bernhard Walle <bernhard@bwalle.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The probe() function will always fail because we're testing the wrong
variable.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A read from GadgetFS endpoint 0 during the data stage of a control
request would always return 0 on success (as returned by
wait_event_interruptible) despite having written data into the user
buffer.
This patch makes it correctly set the return value to the number of
bytes read.
Signed-off-by: Thomas Faber <thfabba@gmx.de>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The kernel doc entry for usb_unlink_urb() contains the phrase "This
request is always asynchronous.". The "always" leads to the assumption
that the ->complete() callback is not called from within
usb_unlink_urb(). This is not true. The HCD is allowed to call the
->complete() from within ->urb_dequeue() if it is appropriate for the
hardware.
This patch updates the kernel doc so usb-device driver authors make sure
to drop all locks (and make sure it is okay to drop them) which are
acquired by the complete callback before calling usb_unlink_urb().
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
As the coverity checker puts it:
"Passing argument "sizeof (midi_function) /*8*/" to function "kcalloc"
and then casting the return value to "struct usb_descriptor_header **"
is suspicious. ... In this particular case sizeof(struct
usb_descriptor_header **) happens to be equal to sizeof(struct
usb_descriptor_header *), but this is not a portable assumption."
I believe we really do intend to use 'sizeof(*midi_function)' here, so
this patch makes that change.
Signed-off-by: Jesper Juhl <jj@chaosbits.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
"len" is unsigned so it's never less than zero.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use the module_platform_driver macro, move the usb_disabled() check to
the probe function and get rid of the rather pointless message on module
load.
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use the module_platform_driver macro, move the usb_disabled() check to
the probe function and get rid of the rather pointless message on module
load.
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>