Right now, "private:" tag should be lower-case, otherwise the
scripts/kernel-doc won't do the right thing.
Also, no fields after "private:" should be documented. As we don't
want to strip the documentation, let's untag. This way, it will
be seen only at the file, and not at the DocBooks.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Since the new multi-queue capability depends on a new firmware API,
we can already add some code for it. If the new API is present, a
new opmode ops struct is used that handles the new rx_rss method.
For now, only restructure the RX handling to distinguish between
the two. Future patches will convert the new infrastructure to
actually use the new RX descriptor layout.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Instead of relying on a hard-coded constant of a maximum of 64 API and
capability bits, add a new enum value after the others that will then
always track the number of used bits in the API/capabilities. We thus
no longer need to maintain the maximum number, and on 32-bit platforms
even (currently) reduce the number of bits kept in memory.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
There's no need to have negative threshold temperatures, so make
them unsigned to avoid signedness warnings in debugfs.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Using an int* instead of u32* as the kstrtou32() output argument
obviously results in signedness warnings, change that.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
This is a tweak which has been shown to improve performance when
moving away from the AP while working in 80Mhz.
When RS decides to go down to 80MHz SISO MCS0 instead switch to 20MHz MCS4.
Go back to 80MHz MCS1 if RS can sustain 20MHz MCS5.
Signed-off-by: Eyal Shapira <eyalx.shapira@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
As the 3165 device uses the same firmware as 7265-D and currently
all 7000 series (including 3160/3165) use the same API versions
remove IWL3165_UCODE_API_OK and _MIN. We might have to put them
back if firmware support ever splits, but in that case might also
have to add a different MODULE_FIRMWARE statement.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
success_ratio is actually 128 * SR in percentage while
IWL_MVM_RS_SR_NO_DECREASE is 85%. Fix this by using RS_PERCENT().
This bug caused the if branch to be always executed. This in turn
led to always selecting a rate, following a column switch, in which
the expected throughput would exceed the best expected current throughput.
In some scenarios where the success ratio isn't >85% such a rate
could be too aggressive leading us to avoid the new column.
This has the potential of causing sub optimal performance.
Reported-by: Moshe Harel <moshe.harel@intel.com>
Signed-off-by: Eyal Shapira <eyalx.shapira@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
This message isn't very useful and creates clutter.
Remove it.
Signed-off-by: Eyal Shapira <eyalx.shapira@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The firmware has always treated these two bits to mean that
powersave is enabled when POWER_SAVE_ENA is set and CAM is
clear; it doesn't use them in any non-combined way.
Therefore, it's pointless to send it two bits, and the API
should be cleaned up. Prepare the driver by removing the CAM
bit and using only POWER_SAVE_ENA to indicate whether PS is
enabled or not.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
When enabling a queue, the default SSN is 0.
Allow determining what that SSN should be, if required. This
can happen, for example, if a queue gets reconfigured.
Signed-off-by: Liad Kaufman <liad.kaufman@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
"DQA" is shorthand for "dynamic queue allocation", with the
idea of allocating queues per-RA/TID on-demand rather than
using shared queues statically allocated per vif. The goal
of this is to enable future features (like GO PM) and to
improve performance measurements of TX traffic.
When RA/TID streams can't be neatly sorted into different AC
queues, DQA allows sharing queues for the same RA. This means
that DQA allows different ACs may reach the same HW queue.
Update the code to allow such queue sharing by having a mapping
between the HW queue and the mac80211 queues using it (as this
could be more than one queue).
Signed-off-by: Liad Kaufman <liad.kaufman@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
As the transport will decide how many queues (and MSI-X vectors)
to allocate, add a field to indicate that to the op-mode so it
can size/allocate its own data structures appropriately.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Upcoming hardware will have the ability to do L3 hashing for RSS,
directing data packets (and perhaps some associated metadata and
management notifications) to different MSI-X vectors.
In this case, it makes no sense to go through the full RX dispatch
since it's already known that only a subset of the possibilities
can come in, requiring a new receive method. In addition this must
know which queue the packet was received on.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Treat PHY RX specially, since it's actually pretty frequent,
doesn't need all the notication etc. code, and will have a
different handler in future hardware.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Return a proper error when wrong parameters are passed to debugfs
tof_range_request.
Signed-off-by: Assaf Krauss <assaf.krauss@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The command needs to have the AP interfaces BSSID (which corresponds
to its address).
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Make some input formats more natural, e.g. bandwidth and periods
are more natural in decimal than in hexadecimal.
Signed-off-by: Assaf Krauss <assaf.krauss@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The driver still was not offloading TSO on GRE tunnels because
it forgot to set the GSO_GRE flag, causing lots of retransmits.
This fixes generic GRE traffic (like a tunnel added like below)
whereas before it would get 1Gb/s or less, now on a 10G adapter
it gets 8.7Gb/s.
ip ad ad 11.1.0.2/24 dev ens2f0
ip l set ens2f0 up
ip link add gre2 type gretap remote 11.1.0.1 local 11.1.0.2 dev ens2f0
ip l set gre2 up
ip ad ad 192.168.124.2/24 dev gre2
ping 192.168.124.1
netperf -H 192.168.124.1
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commit ddd5404007.
We need to preserve only using this naming strategy for names
coming from chip->names[], the descripor->name field is for the
new interface.
There are cases when the created metadata reply is not used. Ensure the
allocated memory is freed also in such cases.
Fixes: 63d008a4e9 ("ipv4: send arp replies to the correct tunnel")
Reported-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: Jiri Benc <jbenc@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
FW dump may be triggered when running init ucode, for example due to a
sysassert. In this case fw_dump_wk may run after mvm is freed, resulting
in a kernel panic.
Fix it by flushing the work.
Fixes: 01b988a708af ("iwlwifi: mvm: allow to collect debug data when restart is disabled")
Cc: <stable@vger.kernel.org> [3.18+]
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
reqsk_timer_handler() tests if icsk_accept_queue.listen_opt
is NULL at its beginning.
By the time it calls inet_csk_reqsk_queue_drop() and
reqsk_queue_unlink(), listener might have been closed and
inet_csk_listen_stop() had called reqsk_queue_yank_acceptq()
which sets icsk_accept_queue.listen_opt to NULL
We therefore need to correctly check listen_opt being NULL
after holding syn_wait_lock for proper synchronization.
Fixes: fa76ce7328 ("inet: get rid of central tcp/dccp listener timer")
Fixes: b357a364c5 ("inet: fix possible panic in reqsk_queue_unlink()")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Yuchung Cheng <ycheng@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
I’m using the compilation flag -Werror=old-style-declaration, which
requires that the “inline” word would come at the beginning of the code
line.
$ make drivers/net/ethernet/intel/e1000e/e1000e.ko
...
include/net/inet_timewait_sock.h:116:1: error: ‘inline’ is not at
beginning of declaration [-Werror=old-style-declaration]
static void inline inet_twsk_schedule(struct inet_timewait_sock *tw, int
timeo)
include/net/inet_timewait_sock.h:121:1: error: ‘inline’ is not at
beginning of declaration [-Werror=old-style-declaration]
static void inline inet_twsk_reschedule(struct inet_timewait_sock *tw,
int timeo)
Fixes: ed2e923945 ("tcp/dccp: fix timewait races in timer handling")
Signed-off-by: Raanan Avargil <raanan.avargil@intel.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This ethernet driver supports the Micorchip enc424j600/626j600 Ethernet
controller over a SPI bus interface. This driver makes use of the regmap API to
optimize access to registers by caching registers where possible.
Datasheet:
http://ww1.microchip.com/downloads/en/DeviceDoc/39935b.pdf
Signed-off-by: Jon Ringle <jringle@gridpoint.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This commit allows installing a custom reg_update_bits function for cases where
the hardware provides a mechanism to set or clear register bits without a
read/modify/write cycle. Such is the case with the Microchip ENCX24J600.
Signed-off-by: Jon Ringle <jringle@gridpoint.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
During the CT-kill exit flow, the card is powered up and partially
initialized to check if the temperature is already low enough.
Unfortunately the init bails early because the CT-kill flag is set.
Make the code bail early only for HW RF-kill, as was intended by the
author. CT-kill is self-imposed and is not really RF-kill.
Fixes: 31b8b343e0 ("iwlwifi: fix RFkill while calibrating")
Cc: <stable@vger.kernel.org> [3.18+]
Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Add 3 new subdevice IDs for the 0x095A device ID and 2 for the 0x095B
device ID.
Cc: <stable@vger.kernerl.org> [3.13+]
Reported-by: Jeremy <jeremy.bomkamp@gmail.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The MODULE_FIRMWARE() for 3160 should be using the 7260 version as
it's done in the device configuration struct instead of referencing
IWL3160_UCODE_API_OK which doesn't even exist.
Cc: <stable@vger.kernel.org> [3.8+]
Reported-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The csa_countdown flag was not cleared when the AP is stopped.
As a result, if the AP was stopped after csa_countdown had started,
all the folowing channel switch commands would fail.
Fix that by clearing the csa_countdown flag when the AP is stopped.
Cc: <stable@vger.kernel.org> [3.17+]
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The current code invokes hang reset in case of error interrupt. We should
hang reset only in case of tx timeout. This because of the way hang reset
is implemented in firmware. Hang reset takes more firmware resources than
soft reset. Adaptor does not generate error interrupt in case of tx
timeout.
Hang reset only in case of tx timeout, in .ndo_tx_timeout. Do soft reset
otherwise. Introduce deferred work, enic_tx_hang_reset, to do hang reset.
Signed-off-by: Govindarajulu Varadarajan <_govind@gmx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some of the enic adaptors are know to generate spurious interrupts. When
error interrupt is generated, driver just resets the device. This patch
resets the device only when an error is occurred.
Signed-off-by: Govindarajulu Varadarajan <_govind@gmx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The code to send the RX PN data (for each TID) to the firmware
has a devastating bug: it overwrites the data for TID 0 with
all the TID data, leaving the remaining TIDs zeroed. This will
allow replays to actually be accepted by the firmware, which
could allow waking up the system.
Cc: <stable@vger.kernel.org> [3.1+]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The code to send the RX PN data (for each TID) to the firmware
has a devastating bug: it overwrites the data for TID 0 with
all the TID data, leaving the remaining TIDs zeroed. This will
allow replays to actually be accepted by the firmware, which
could allow waking up the system.
Cc: <stable@vger.kernel.org> [3.1+]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Hariprasad Shenai says:
====================
cxgb4: Trivial fixes for cxgb4
Fixes the following issues
Don't read non existent T4/T5/T6 adapter registers for ethtool dump.
For T4, dont read mailbox control registers. Adds new devlog faility and
report correct link speed for unsupported ones.
This patch series has been created against net-next tree and includes
patches on cxgb4 driver.
We have included all the maintainers of respective drivers. Kindly review
the change and let us know in case of any review comments.
====================
Acked-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When we get garbage from the firmware with weird Port Speeds,
etc. we should emit a warning regarding unsupported speeds rather than
use the bogus default of "10Mbps" which isn't even an option in the
firmware Port Information message
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The firmware team added a new Device Log Facility FW_DEVLOG_FACILITY_CF,
but the driver has been decoding Device Log messages with that Facility as
"(NULL)", fixing it.
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
T4 doesn't have the Shadow copy of the register which we can read without
side effect. So don't read mbox control register for T4 adapter
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Update T4/T5/T6 adapter register ranges so that it doesn't read non
existent registers when dumped using ethtool
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When going into/coming out of D3, the TX PN must be programmed into
and restored from the firmware respectively. The restore was broken
due to my previous commit to move PN assignment into the driver.
Sending the PN to the firmware still worked since we now use the
counter that's shared with mac80211, but accessing it through the
mac80211 API makes no sense now.
Fix this by reading/writing the counter directly. This actually
simplifies the code since we don't need to round-trip through the
key_seq structure.
Fixes: ca8c0f4bed ("iwlwifi: mvm: move TX PN assignment for CCMP to the driver")
Cc: <stable@vger.kernel.org> [4.1+]
Reported-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
If common clock framework is configured, the driver generates warnings,
which are fixed by this change:
WARNING: CPU: 0 PID: 1 at linux/drivers/clk/clk.c:727 clk_core_enable+0x2c/0xa4()
Modules linked in:
CPU: 0 PID: 1 Comm: swapper Not tainted 4.3.0-rc2+ #141
Hardware name: LPC32XX SoC (Flattened Device Tree)
Backtrace:
[<>] (dump_backtrace) from [<>] (show_stack+0x18/0x1c)
[<>] (show_stack) from [<>] (dump_stack+0x20/0x28)
[<>] (dump_stack) from [<>] (warn_slowpath_common+0x90/0xb8)
[<>] (warn_slowpath_common) from [<>] (warn_slowpath_null+0x24/0x2c)
[<>] (warn_slowpath_null) from [<>] (clk_core_enable+0x2c/0xa4)
[<>] (clk_core_enable) from [<>] (clk_enable+0x24/0x38)
[<>] (clk_enable) from [<>] (lpc_eth_drv_probe+0xfc/0x99c)
[<>] (lpc_eth_drv_probe) from [<>] (platform_drv_probe+0x50/0xa0)
[<>] (platform_drv_probe) from [<>] (driver_probe_device+0x18c/0x408)
[<>] (driver_probe_device) from [<>] (__driver_attach+0x70/0x94)
[<>] (__driver_attach) from [<>] (bus_for_each_dev+0x74/0x98)
[<>] (bus_for_each_dev) from [<>] (driver_attach+0x20/0x28)
[<>] (driver_attach) from [<>] (bus_add_driver+0x11c/0x248)
[<>] (bus_add_driver) from [<>] (driver_register+0xa4/0xe8)
[<>] (driver_register) from [<>] (__platform_driver_register+0x50/0x64)
[<>] (__platform_driver_register) from [<>] (lpc_eth_driver_init+0x18/0x20)
[<>] (lpc_eth_driver_init) from [<>] (do_one_initcall+0x11c/0x1dc)
[<>] (do_one_initcall) from [<>] (kernel_init_freeable+0x10c/0x1d4)
[<>] (kernel_init_freeable) from [<>] (kernel_init+0x10/0xec)
[<>] (kernel_init) from [<>] (ret_from_fork+0x14/0x24)
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Eric W. Biederman says:
====================
net: Pass net through ip fragmention
This is the next installment of my work to pass struct net through the
output path so the code does not need to guess how to figure out which
network namespace it is in, and ultimately routes can have output
devices in another network namespace.
This round focuses on passing net through ip fragmentation which we seem
to call from about everywhere. That is the main ip output paths, the
bridge netfilter code, and openvswitch. This has to happend at once
accross the tree as function pointers are involved.
First some prep work is done, then ipv4 and ipv6 are converted and then
temporary helper functions are removed.
====================
Acked-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Sowmini Varadhan says:
====================
RDS: RDS-TCP perf enhancements
A 3-part patchset that (a) improves current RDS-TCP perf
by 2X-3X and (b) refactors earlier robustness code for
better observability/scaling.
Patch 1 is an enhancment of earlier robustness fixes
that had used separate sockets for client and server endpoints to
resolve race conditions. It is possible to have an equivalent
solution that does not use 2 sockets. The benefit of a
single socket solution is that it results in more predictable
and observable behavior for the underlying TCP pipe of an
RDS connection
Patches 2 and 3 are simple, straightforward perf bug fixes
that align the RDS TCP socket with other parts of the kernel stack.
v2: fix kbuild-test-robot warnings, comments from Sergei Shtylov
and Santosh Shilimkar.
====================
Acked-by: Santosh Shilimkar <santosh.shilimkar@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For the same reasons as commit 2f53384424 ("tcp: allow splice() to
build full TSO packets") and commit 35f9c09fe9 ("tcp: tcp_sendpages()
should call tcp_push() once"), rds_tcp_xmit may have multiple pages to
send, so use the MSG_MORE and MSG_SENDPAGE_NOTLAST as hints to
tcp_sendpage()
Signed-off-by: Sowmini Varadhan <sowmini.varadhan@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
