The ilw@linux.intel.com address is being phased out, replace
it with the new address.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The formula used in D0i3 should also be used in D3, instead of
the hardcoded value.
Additionally, the formula is actually wrong - if the calculation
yields 0 then 1 should be used instead of disabling entirely.
Also need to add 1 since the firmware needs 3 to skip 2, etc.
To make all this clearer, centralize the calculation into a
single function.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
This is a workaround to an OTP bug. In Series 8000 1x1, the OTP
0xA052 defines 2x2 antenna configuration. This workaround overrides
the decision based on HW id and MIMO disabled bit which is correct
in the OTP and set to disabled.
Signed-off-by: Moshe Harel <moshe.harel@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Move the DTS measurement command and notification from short
command header to the new PHY command group for firmware
supporting the extended command headers.
Signed-off-by: Aviya Erenfeld <aviya.erenfeld@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
This patch adds a support of the expandes found on Intel Galileo Gen2 board.
The platform information comes from ACPI.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Instead of using id->driver_data directly we copied it to the internal
structure. This will help to adapt driver for ACPI use.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
We need to call intel_runtime_pm_put() and mutex_unlock() before
returning.
Fixes: 7cb5dff8d5 ('drm/i915: fix task reference leak in i915_debugfs.c')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Geliang Tang <geliangtang@163.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
When the core starts or shuts down the actual HCI transport, send a new
monitor event that indicates that this is happening. These new events
correspond to HCI_DEV_OPEN and HCI_DEV_CLOSE events.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Setting and clearing of HCI_RUNNING flag in each and every driver is
just duplicating the same code all over the place. So instead of having
the driver do it in their hdev->open and hdev->close callbacks, set it
globally in the core transport handling.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
In all callbacks for hdev->send the status of HCI_RUNNING is checked. So
instead of repeating that code in every driver, move the check into the
hci_send_frame function before calling hdev->send.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
When opening the HCI transport via hdev->open send HCI_DEV_OPEN event
and when closing the HCI transport via hdev->close send HCI_DEV_CLOSE.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The stack internal events that are exposed to userspace should be
limited to HCI_DEV_REG, HCI_DEV_UNREG, HCI_DEV_UP and HCI_DEV_DOWN.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The commit 7bee8b08c4 allows the Read Verbose Config Info to fail
gracefully and not cause the controller setup to abort. It seems the
reason that command failed in the first place was the missing HCI Reset
to bring the controller in full Bluetooth mode.
Apple Bluetooth controllers start out in HID mode and when in that mode
the Read Verbose Config Info command is not allowed. Sending HCI Reset
switches the controller into full HCI mode.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Use the ERRPTR standard way to return an error code in a pointer
thus simplifiying the code.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
If bgpio_map returns NULL then err should always be set.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
If a MCB PCI Carrier device is IO mapped insted of memory-mapped,
the memory of the PCI device is still not unmapped.
Also the patch adds deallocation of the bus
if chameleon_parse_cells() fails.
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Signed-off-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some modules register several sub-drivers. Provide a helper that makes
it easy to register and unregister a list of sub-drivers, as well as
unwind properly on error.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Mention that the ldisc open method must set tty->receive_room, and
that many methods are optional. Add description of receive_buf2 method.
Signed-off-by: Tilman Schmidt <tilman@imap.cc>
Reviewed-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Tony found on his setup, if memory block size 512M will cause crash
during booting.
BUG: unable to handle kernel paging request at ffffea0074000020
IP: [<ffffffff81670527>] get_nid_for_pfn+0x17/0x40
PGD 128ffcb067 PUD 128ffc9067 PMD 0
Oops: 0000 [#1] SMP
Modules linked in:
CPU: 0 PID: 1 Comm: swapper/0 Not tainted 4.2.0-rc8 #1
...
Call Trace:
[<ffffffff81453b56>] ? register_mem_sect_under_node+0x66/0xe0
[<ffffffff81453eeb>] register_one_node+0x17b/0x240
[<ffffffff81b1f1ed>] ? pci_iommu_alloc+0x6e/0x6e
[<ffffffff81b1f229>] topology_init+0x3c/0x95
[<ffffffff8100213d>] do_one_initcall+0xcd/0x1f0
The system has non continuous RAM address:
BIOS-e820: [mem 0x0000001300000000-0x0000001cffffffff] usable
BIOS-e820: [mem 0x0000001d70000000-0x0000001ec7ffefff] usable
BIOS-e820: [mem 0x0000001f00000000-0x0000002bffffffff] usable
BIOS-e820: [mem 0x0000002c18000000-0x0000002d6fffefff] usable
BIOS-e820: [mem 0x0000002e00000000-0x00000039ffffffff] usable
So there are start sections in memory block not present.
For example:
memory block : [0x2c18000000, 0x2c20000000) 512M
first three sections are not present.
Current register_mem_sect_under_node() assume first section is present,
but memory block section number range [start_section_nr, end_section_nr]
would include not present section.
For arch that support vmemmap, we don't setup memmap for struct page area
within not present sections area.
So skip the pfn range that belong to absent section.
Also fixes unregister_mem_sect_under_nodes() that assume one section per
memory block.
Reported-by: Tony Luck <tony.luck@intel.com>
Tested-by: Tony Luck <tony.luck@intel.com>
Fixes: bdee237c03 ("x86: mm: Use 2GB memory block size on large memory x86-64 systems")
Fixes: 982792c782 ("x86, mm: probe memory block size for generic x86 64bit")
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Cc: stable@vger.kernel.org #v3.15
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The iomap[] array has PCIM_IOMAP_MAX (6) elements and not
DEVICE_COUNT_RESOURCE (16). This bug was found using a static checker.
It may be that the "if (!(mask & (1 << i)))" check means we never
actually go past the end of the array in real life.
Fixes: ec04b07584 ('iomap: implement pcim_iounmap_regions()')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In 64bit system, if you set CONFIG_CMA_SIZE_MBYTES>=2048, it will
overflow and size_bytes will be a big wrong number.
Set CONFIG_CMA_SIZE_MBYTES=2048 and you will get an info below
during system boot:
*********
cma: Failed to reserve 17592186042368 MiB
*********
Signed-off-by: Tan Xiaojun <tanxiaojun@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patches makes following changes to omap_hdq driver
- Enable 1-wire mode.
- Implement w1_triplet callback to facilitate search rom
procedure and auto detection of 1-wire slaves.
- Proper enabling and disabling of interrupt.
- Cleanups (formatting and return value checks).
HDQ mode remains unchanged.
Signed-off-by: Vignesh R <vigneshr@ti.com>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Pawel Moll <pawel.moll@arm.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Ian Campbell <ijc+devicetree@hellion.org.uk>
Cc: Kumar Gala <galak@codeaurora.org>
Acked-by: Evgeniy Polyakov <zbr@ioremap.net>
Cc: Jonathan Corbet <corbet@lwn.net>
CC: Tony Lindgren <tony@atomide.com>
Cc: Vignesh R <vigneshr@ti.com>
Cc: NeilBrown <neilb@suse.de>
Cc: Fabian Frederick <fabf@skynet.be>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently, memsetting and kfreeing the device is bad behaviour. The
device will have a reference count of 1 and hence can cause trouble
because it has kfree'd. Proper way to handle a failed device_register is
to call put_device right after it fails.
Signed-off-by: Levente Kurusa <levex@linux.com>
Acked-by: Evgeniy Polyakov <zbr@ioremap.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use kstrdup instead of kmalloc and strncpy.
Signed-off-by: Geliang Tang <geliangtang@163.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This platform driver has a OF device ID table but the OF module
alias information is not created so module autoloading won't work.
Signed-off-by: Luis de Bethencourt <luisbg@osg.samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This platform driver has a OF device ID table but the OF module
alias information is not created so module autoloading won't work.
Signed-off-by: Luis de Bethencourt <luisbg@osg.samsung.com>
Acked-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
SCIF depends on IOVA which requires IOMMU_SUPPORT to be enabled.
The long term fix is to move IOVA from drivers/iommu to lib/
but this current patch should fix the reported issue.
Reported-by: Fengguang Wu <fengguang.wu@intel.com>
Reviewed-by: Ashutosh Dixit <ashutosh.dixit@intel.com>
Signed-off-by: Sudeep Dutt <sudeep.dutt@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Unfortunately, the SILK board bindings were not quite correct, as the board
name should be all caps. Fix that, adding the board model # in parens and
removing stray semicolon.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Define the R8A7794 generic part of the HS-USB device node.
It is up to the board file to enable the device.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Nikolay Aleksandrov says:
====================
bridge: complete netlink support
This set completes the bridge device's netlink support and makes it
possible to view and configure everything that can be configured via
sysfs. I have tested all of these (setting and getting). There're a few
longer line warnings about the br_get_size() ifla comments but I think we
should have them to know what has been accounted for. I have used the sysfs
interface as a guide of what and how to set. As usual I'll send the
corresponding iproute2 patches later.
The bridge port's netlink interface will be completed after this set gets
applied in some form.
This patch-set is on top of my last vlan cleanups set:
http://www.spinics.net/lists/netdev/msg346005.html
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Add IFLA_BR_VLAN_DEFAULT_PVID to allow setting/getting bridge's
default_pvid via netlink.
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support to allow getting/setting netfilter tables settings.
Currently these are IFLA_BR_NF_CALL_IPTABLES, IFLA_BR_NF_CALL_IP6TABLES
and IFLA_BR_NF_CALL_ARPTABLES.
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support to set/get all of the igmp's configurable intervals via
netlink. These currently are:
IFLA_BR_MCAST_LAST_MEMBER_INTVL
IFLA_BR_MCAST_MEMBERSHIP_INTVL
IFLA_BR_MCAST_QUERIER_INTVL
IFLA_BR_MCAST_QUERY_INTVL
IFLA_BR_MCAST_QUERY_RESPONSE_INTVL
IFLA_BR_MCAST_STARTUP_QUERY_INTVL
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add IFLA_BR_MCAST_STARTUP_QUERY_CNT to allow setting/getting
br->multicast_startup_query_count via netlink. Also align the ifla
comments.
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add IFLA_BR_MCAST_LAST_MEMBER_CNT to allow setting/getting
br->multicast_last_member_count via netlink.
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add IFLA_BR_MCAST_HASH_MAX to allow setting/getting br->hash_max via
netlink.
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add IFLA_BR_MCAST_HASH_ELASTICITY to allow setting/getting
br->hash_elasticity via netlink.
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add IFLA_BR_MCAST_QUERIER to allow setting/getting br->multicast_querier
via netlink.
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add IFLA_BR_MCAST_QUERY_USE_IFADDR to allow setting/getting
br->multicast_query_use_ifaddr via netlink.
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add IFLA_BR_MCAST_SNOOPING to allow enabling/disabling multicast
snooping via netlink.
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add IFLA_BR_MCAST_ROUTER to allow setting and retrieving
br->multicast_router when igmp snooping is enabled.
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Simple attribute that flushes the bridge's fdb.
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add IFLA_BR_GROUP_ADDR attribute to allow setting and retrieving the
group_addr via netlink.
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Export the following bridge timers (also exported via sysfs):
IFLA_BR_HELLO_TIMER, IFLA_BR_TCN_TIMER, IFLA_BR_TOPOLOGY_CHANGE_TIMER,
IFLA_BR_GC_TIMER via netlink.
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add IFLA_BR_TOPOLOGY_CHANGE and IFLA_BR_TOPOLOGY_CHANGE_DETECTED and
export them via netlink.
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add IFLA_BR_ROOT_PATH_COST and export it via netlink.
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add IFLA_BR_ROOT_PORT and export it via netlink.
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add IFLA_BR_BRIDGE_ID and export br->bridge_id via netlink.
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
